summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorSergei Shtylyov <sshtylyov@ru.mvista.com>2007-05-05 22:03:49 +0200
committerBartlomiej Zolnierkiewicz <bzolnier@gmail.com>2007-05-05 22:03:49 +0200
commit60e7a82f1acb76af05d81e93ca0f65fdd52c23c2 (patch)
treebe3868264f513cbb2979dc6059aa0cb525b62365
parent688a87d145e04f6761c63e7f2e19fd9b3e4ca060 (diff)
cmd64x: fix multiword and remove single-word DMA support
Fix the multiword DMA and drop the single-word DMA support (which nobody will miss, I think). In order to do it, a number of changes was necessary: - rename program_drive_counts() to program_cycle_times(), pass to it cycle's total/active times instead of the clock counts, and convert them into the active/recovery clocks there instead of cmd64x_tune_pio() -- this causes quantize_timing() to also move; - contrarywise, move all the code handling the address setup timing into cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup; - remove from the speedproc() method the bogus code pretending to set the DMA timings by twiddling bits in the BMIDE status register, handle setting MWDMA by just calling program_cycle_times(); while at it, improve the style of that whole switch statement; - stop fiddling with the DMA capable bits in the speedproc() method -- they do not enable DMA, and are properly dealt with by the dma_host_{on,off} methods; - don't set hwif->swdma_mask in the init_hwif() method anymore. In addition to those changes, do the following: - in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt status bit, eliminate local_irq_{save|restore}() around this code as there's *no* actual race with the interrupt handler, and move cmdprintk() to a more fitting place -- after ide_get_best_pio_mode() call; - make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn; - rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[]; - in the speedproc() method, get rid of the duplicate reads/writes from/to the UDIDETCRx registers and of the extra variable used to store the transfer mode value after filtering, use another method of determining master/slave drive, and cleanup useless parens; - beautify cmdprintk() output here and there. While at it, remove meaningless comment about the driver being used only on UltraSPARC and long non-relevant RCS tag. :-) Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-rw-r--r--drivers/ide/pci/cmd64x.c248
1 files changed, 117 insertions, 131 deletions
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index 561197f7b5b..336d02f5801 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -1,10 +1,7 @@
-/* $Id: cmd64x.c,v 1.21 2000/01/30 23:23:16
- *
- * linux/drivers/ide/pci/cmd64x.c Version 1.42 Feb 8, 2007
+/*
+ * linux/drivers/ide/pci/cmd64x.c Version 1.43 Mar 10, 2007
*
* cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
- * Note, this driver is not used at all on other systems because
- * there the "BIOS" has done all of the following already.
* Due to massive hardware bugs, UltraDMA is only supported
* on the 646U2 and not on the 646U.
*
@@ -195,116 +192,103 @@ static u8 quantize_timing(int timing, int quant)
}
/*
- * This routine writes the prepared setup/active/recovery counts
- * for a drive into the cmd646 chipset registers to active them.
+ * This routine calculates active/recovery counts and then writes them into
+ * the chipset registers.
*/
-static void program_drive_counts (ide_drive_t *drive, int setup_count, int active_count, int recovery_count)
+static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_time)
{
- unsigned long flags;
- struct pci_dev *dev = HWIF(drive)->pci_dev;
- ide_drive_t *drives = HWIF(drive)->drives;
- u8 temp_b;
- static const u8 setup_counts[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
- static const u8 recovery_counts[] =
+ struct pci_dev *dev = HWIF(drive)->pci_dev;
+ int clock_time = 1000 / system_bus_clock();
+ u8 cycle_count, active_count, recovery_count, drwtim;
+ static const u8 recovery_values[] =
{15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
- static const u8 arttim_regs[2][2] = {
- { ARTTIM0, ARTTIM1 },
- { ARTTIM23, ARTTIM23 }
- };
- static const u8 drwtim_regs[2][2] = {
- { DRWTIM0, DRWTIM1 },
- { DRWTIM2, DRWTIM3 }
- };
- int channel = (int) HWIF(drive)->channel;
- int slave = (drives != drive); /* Is this really the best way to determine this?? */
-
- cmdprintk("program_drive_count parameters = s(%d),a(%d),r(%d),p(%d)\n",
- setup_count, active_count, recovery_count, drive->present);
+ static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};
+
+ cmdprintk("program_cycle_times parameters: total=%d, active=%d\n",
+ cycle_time, active_time);
+
+ cycle_count = quantize_timing( cycle_time, clock_time);
+ active_count = quantize_timing(active_time, clock_time);
+ recovery_count = cycle_count - active_count;
+
/*
- * Set up address setup count registers.
- * Primary interface has individual count/timing registers for
- * each drive. Secondary interface has one common set of registers,
- * for address setup so we merge these timings, using the slowest
- * value.
+ * In case we've got too long recovery phase, try to lengthen
+ * the active phase
*/
- if (channel) {
- drive->drive_data = setup_count;
- setup_count = max(drives[0].drive_data,
- drives[1].drive_data);
- cmdprintk("Secondary interface, setup_count = %d\n",
- setup_count);
+ if (recovery_count > 16) {
+ active_count += recovery_count - 16;
+ recovery_count = 16;
}
+ if (active_count > 16) /* shouldn't actually happen... */
+ active_count = 16;
+
+ cmdprintk("Final counts: total=%d, active=%d, recovery=%d\n",
+ cycle_count, active_count, recovery_count);
/*
* Convert values to internal chipset representation
*/
- setup_count = (setup_count > 5) ? 0xc0 : (int) setup_counts[setup_count];
- active_count &= 0xf; /* Remember, max value is 16 */
- recovery_count = (int) recovery_counts[recovery_count];
-
- cmdprintk("Final values = %d,%d,%d\n",
- setup_count, active_count, recovery_count);
+ recovery_count = recovery_values[recovery_count];
+ active_count &= 0x0f;
- /*
- * Now that everything is ready, program the new timings
- */
- local_irq_save(flags);
- /*
- * Program the address_setup clocks into ARTTIM reg,
- * and then the active/recovery counts into the DRWTIM reg
- */
- (void) pci_read_config_byte(dev, arttim_regs[channel][slave], &temp_b);
- (void) pci_write_config_byte(dev, arttim_regs[channel][slave],
- ((u8) setup_count) | (temp_b & 0x3f));
- (void) pci_write_config_byte(dev, drwtim_regs[channel][slave],
- (u8) ((active_count << 4) | recovery_count));
- cmdprintk ("Write %x to %x\n",
- ((u8) setup_count) | (temp_b & 0x3f),
- arttim_regs[channel][slave]);
- cmdprintk ("Write %x to %x\n",
- (u8) ((active_count << 4) | recovery_count),
- drwtim_regs[channel][slave]);
- local_irq_restore(flags);
+ /* Program the active/recovery counts into the DRWTIM register */
+ drwtim = (active_count << 4) | recovery_count;
+ (void) pci_write_config_byte(dev, drwtim_regs[drive->dn], drwtim);
+ cmdprintk("Write 0x%02x to reg 0x%x\n", drwtim, drwtim_regs[drive->dn]);
}
/*
- * This routine selects drive's best PIO mode, calculates setup/active/recovery
- * counts, and then writes them into the chipset registers.
+ * This routine selects drive's best PIO mode and writes into the chipset
+ * registers setup/active/recovery timings.
*/
static u8 cmd64x_tune_pio (ide_drive_t *drive, u8 mode_wanted)
{
- int setup_time, active_time, cycle_time;
- u8 cycle_count, setup_count, active_count, recovery_count;
- u8 pio_mode;
- int clock_time = 1000 / system_bus_clock();
+ ide_hwif_t *hwif = HWIF(drive);
+ struct pci_dev *dev = hwif->pci_dev;
ide_pio_data_t pio;
-
+ u8 pio_mode, setup_count, arttim = 0;
+ static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
+ static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
pio_mode = ide_get_best_pio_mode(drive, mode_wanted, 5, &pio);
- cycle_time = pio.cycle_time;
- setup_time = ide_pio_timings[pio_mode].setup_time;
- active_time = ide_pio_timings[pio_mode].active_time;
+ cmdprintk("%s: PIO mode wanted %d, selected %d (%d ns)%s\n",
+ drive->name, mode_wanted, pio_mode, pio.cycle_time,
+ pio.overridden ? " (overriding vendor mode)" : "");
- setup_count = quantize_timing( setup_time, clock_time);
- cycle_count = quantize_timing( cycle_time, clock_time);
- active_count = quantize_timing(active_time, clock_time);
+ program_cycle_times(drive, pio.cycle_time,
+ ide_pio_timings[pio_mode].active_time);
- recovery_count = cycle_count - active_count;
- /* program_drive_counts() takes care of zero recovery cycles */
- if (recovery_count > 16) {
- active_count += recovery_count - 16;
- recovery_count = 16;
+ setup_count = quantize_timing(ide_pio_timings[pio_mode].setup_time,
+ 1000 / system_bus_clock());
+
+ /*
+ * The primary channel has individual address setup timing registers
+ * for each drive and the hardware selects the slowest timing itself.
+ * The secondary channel has one common register and we have to select
+ * the slowest address setup timing ourselves.
+ */
+ if (hwif->channel) {
+ ide_drive_t *drives = hwif->drives;
+
+ drive->drive_data = setup_count;
+ setup_count = max(drives[0].drive_data, drives[1].drive_data);
}
- if (active_count > 16)
- active_count = 16; /* maximum allowed by cmd64x */
- program_drive_counts (drive, setup_count, active_count, recovery_count);
+ if (setup_count > 5) /* shouldn't actually happen... */
+ setup_count = 5;
+ cmdprintk("Final address setup count: %d\n", setup_count);
- cmdprintk("%s: PIO mode wanted %d, selected %d (%dns)%s, "
- "clocks=%d/%d/%d\n",
- drive->name, mode_wanted, pio_mode, cycle_time,
- pio.overridden ? " (overriding vendor mode)" : "",
- setup_count, active_count, recovery_count);
+ /*
+ * Program the address setup clocks into the ARTTIM registers.
+ * Avoid clearing the secondary channel's interrupt bit.
+ */
+ (void) pci_read_config_byte (dev, arttim_regs[drive->dn], &arttim);
+ if (hwif->channel)
+ arttim &= ~ARTTIM23_INTR_CH1;
+ arttim &= ~0xc0;
+ arttim |= setup_values[setup_count];
+ (void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
+ cmdprintk("Write 0x%02x to reg 0x%x\n", arttim, arttim_regs[drive->dn]);
return pio_mode;
}
@@ -376,61 +360,64 @@ static u8 cmd64x_ratemask (ide_drive_t *drive)
return mode;
}
-static int cmd64x_tune_chipset (ide_drive_t *drive, u8 xferspeed)
+static int cmd64x_tune_chipset (ide_drive_t *drive, u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
+ u8 unit = drive->dn & 0x01;
+ u8 regU = 0, pciU = hwif->channel ? UDIDETCR1 : UDIDETCR0;
- u8 unit = (drive->select.b.unit & 0x01);
- u8 regU = 0, pciU = (hwif->channel) ? UDIDETCR1 : UDIDETCR0;
- u8 regD = 0, pciD = (hwif->channel) ? BMIDESR1 : BMIDESR0;
-
- u8 speed = ide_rate_filter(cmd64x_ratemask(drive), xferspeed);
+ speed = ide_rate_filter(cmd64x_ratemask(drive), speed);
if (speed >= XFER_SW_DMA_0) {
- (void) pci_read_config_byte(dev, pciD, &regD);
(void) pci_read_config_byte(dev, pciU, &regU);
- regD &= ~(unit ? 0x40 : 0x20);
regU &= ~(unit ? 0xCA : 0x35);
- (void) pci_write_config_byte(dev, pciD, regD);
- (void) pci_write_config_byte(dev, pciU, regU);
- (void) pci_read_config_byte(dev, pciD, &regD);
- (void) pci_read_config_byte(dev, pciU, &regU);
}
switch(speed) {
- case XFER_UDMA_5: regU |= (unit ? 0x0A : 0x05); break;
- case XFER_UDMA_4: regU |= (unit ? 0x4A : 0x15); break;
- case XFER_UDMA_3: regU |= (unit ? 0x8A : 0x25); break;
- case XFER_UDMA_2: regU |= (unit ? 0x42 : 0x11); break;
- case XFER_UDMA_1: regU |= (unit ? 0x82 : 0x21); break;
- case XFER_UDMA_0: regU |= (unit ? 0xC2 : 0x31); break;
- case XFER_MW_DMA_2: regD |= (unit ? 0x40 : 0x10); break;
- case XFER_MW_DMA_1: regD |= (unit ? 0x80 : 0x20); break;
- case XFER_MW_DMA_0: regD |= (unit ? 0xC0 : 0x30); break;
- case XFER_SW_DMA_2: regD |= (unit ? 0x40 : 0x10); break;
- case XFER_SW_DMA_1: regD |= (unit ? 0x80 : 0x20); break;
- case XFER_SW_DMA_0: regD |= (unit ? 0xC0 : 0x30); break;
- case XFER_PIO_5:
- case XFER_PIO_4:
- case XFER_PIO_3:
- case XFER_PIO_2:
- case XFER_PIO_1:
- case XFER_PIO_0:
- (void) cmd64x_tune_pio(drive, speed - XFER_PIO_0);
- break;
-
- default:
- return 1;
+ case XFER_UDMA_5:
+ regU |= unit ? 0x0A : 0x05;
+ break;
+ case XFER_UDMA_4:
+ regU |= unit ? 0x4A : 0x15;
+ break;
+ case XFER_UDMA_3:
+ regU |= unit ? 0x8A : 0x25;
+ break;
+ case XFER_UDMA_2:
+ regU |= unit ? 0x42 : 0x11;
+ break;
+ case XFER_UDMA_1:
+ regU |= unit ? 0x82 : 0x21;
+ break;
+ case XFER_UDMA_0:
+ regU |= unit ? 0xC2 : 0x31;
+ break;
+ case XFER_MW_DMA_2:
+ program_cycle_times(drive, 120, 70);
+ break;
+ case XFER_MW_DMA_1:
+ program_cycle_times(drive, 150, 80);
+ break;
+ case XFER_MW_DMA_0:
+ program_cycle_times(drive, 480, 215);
+ break;
+ case XFER_PIO_5:
+ case XFER_PIO_4:
+ case XFER_PIO_3:
+ case XFER_PIO_2:
+ case XFER_PIO_1:
+ case XFER_PIO_0:
+ (void) cmd64x_tune_pio(drive, speed - XFER_PIO_0);
+ break;
+ default:
+ return 1;
}
- if (speed >= XFER_SW_DMA_0) {
+ if (speed >= XFER_SW_DMA_0)
(void) pci_write_config_byte(dev, pciU, regU);
- regD |= (unit ? 0x40 : 0x20);
- (void) pci_write_config_byte(dev, pciD, regD);
- }
- return (ide_config_drive_speed(drive, speed));
+ return ide_config_drive_speed(drive, speed);
}
static int config_chipset_for_dma (ide_drive_t *drive)
@@ -665,7 +652,6 @@ static void __devinit init_hwif_cmd64x(ide_hwif_t *hwif)
hwif->ultra_mask = 0x3f;
hwif->mwdma_mask = 0x07;
- hwif->swdma_mask = 0x07;
if (dev->device == PCI_DEVICE_ID_CMD_643)
hwif->ultra_mask = 0x80;