Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6: (44 commits)
  [PATCH] I2C: I2C controllers go into right place on sysfs
  [PATCH] hwmon-vid: Add support for Intel Core and Conroe
  [PATCH] lm70: New hardware monitoring driver
  [PATCH] hwmon: Fix the Kconfig header
  [PATCH] i2c-i801: Merge setup function
  [PATCH] i2c-i801: Better pci subsystem integration
  [PATCH] i2c-i801: Cleanups
  [PATCH] i2c-i801: Remove PCI function check
  [PATCH] i2c-i801: Remove force_addr parameter
  [PATCH] i2c-i801: Fix block transaction poll loops
  [PATCH] scx200_acb: Documentation update
  [PATCH] scx200_acb: Mark scx200_acb_probe __init
  [PATCH] scx200_acb: Use PCI I/O resource when appropriate
  [PATCH] i2c: Mark block write buffers as const
  [PATCH] i2c-ocores: Minor cleanups
  [PATCH] abituguru: Fix fan detection
  [PATCH] abituguru: Review fixes
  [PATCH] abituguru: New hardware monitoring driver
  [PATCH] w83792d: Add missing data access locks
  [PATCH] w83792d: Fix setting the PWM value
  ...

41 files changed, 5747 insertions, 474 deletions

diff --git a/Documentation/hwmon/abituguru b/Documentation/hwmon/abituguru
new file mode 100644
index 00000000000..69cdb527d58
--- /dev/null
+++ b/Documentation/hwmon/abituguru
@@ -0,0 +1,59 @@
+Kernel driver abituguru
+=======================
+
+Supported chips:
+  * Abit uGuru (Hardware Monitor part only)
+    Prefix: 'abituguru'
+    Addresses scanned: ISA 0x0E0
+    Datasheet: Not available, this driver is based on reverse engineering.
+	A "Datasheet" has been written based on the reverse engineering it
+	should be available in the same dir as this file under the name
+	abituguru-datasheet.
+
+Authors:
+	Hans de Goede <j.w.r.degoede@hhs.nl>,
+	(Initial reverse engineering done by Olle Sandberg
+	 <ollebull@gmail.com>)
+
+
+Module Parameters
+-----------------
+
+* force: bool		Force detection. Note this parameter only causes the
+			detection to be skipped, if the uGuru can't be read
+			the module initialization (insmod) will still fail.
+* fan_sensors: int	Tell the driver how many fan speed sensors there are
+			on your motherboard. Default: 0 (autodetect).
+* pwms: int		Tell the driver how many fan speed controls (fan
+			pwms) your motherboard has. Default: 0 (autodetect).
+* verbose: int		How verbose should the driver be? (0-3):
+			   0 normal output
+			   1 + verbose error reporting
+			   2 + sensors type probing info\n"
+			   3 + retryable error reporting
+			Default: 2 (the driver is still in the testing phase)
+
+Notice if you need any of the first three options above please insmod the
+driver with verbose set to 3 and mail me <j.w.r.degoede@hhs.nl> the output of:
+dmesg | grep abituguru
+
+
+Description
+-----------
+
+This driver supports the hardware monitoring features of the Abit uGuru chip
+found on Abit uGuru featuring motherboards (most modern Abit motherboards).
+
+The uGuru chip in reality is a Winbond W83L950D in disguise (despite Abit
+claiming it is "a new microprocessor designed by the ABIT Engineers").
+Unfortunatly this doesn't help since the W83L950D is a generic
+microcontroller with a custom Abit application running on it.
+
+Despite Abit not releasing any information regarding the uGuru, Olle
+Sandberg <ollebull@gmail.com> has managed to reverse engineer the sensor part
+of the uGuru. Without his work this driver would not have been possible.
+
+Known Issues
+------------
+
+The voltage and frequency control parts of the Abit uGuru are not supported.
diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet
new file mode 100644
index 00000000000..aef5a9b3684
--- /dev/null
+++ b/Documentation/hwmon/abituguru-datasheet
@@ -0,0 +1,312 @@
+uGuru datasheet
+===============
+
+First of all, what I know about uGuru is no fact based on any help, hints or
+datasheet from Abit. The data I have got on uGuru have I assembled through
+my weak knowledge in "backwards engineering".
+And just for the record, you may have noticed uGuru isn't a chip developed by
+Abit, as they claim it to be. It's realy just an microprocessor (uC) created by
+Winbond (W83L950D). And no, reading the manual for this specific uC or
+mailing  Windbond for help won't give any usefull data about uGuru, as it is
+the program inside the uC that is responding to calls.
+
+Olle Sandberg <ollebull@gmail.com>, 2005-05-25
+
+
+Original version by Olle Sandberg who did the heavy lifting of the initial
+reverse engineering. This version has been almost fully rewritten for clarity
+and extended with write support and info on more databanks, the write support
+is once again reverse engineered by Olle the additional databanks have been
+reverse engineered by me. I would like to express my thanks to Olle, this
+document and the Linux driver could not have been written without his efforts.
+
+Note: because of the lack of specs only the sensors part of the uGuru is
+described here and not the CPU / RAM / etc voltage & frequency control.
+
+Hans de Goede <j.w.r.degoede@hhs.nl>, 28-01-2006
+
+
+Detection
+=========
+
+As far as known the uGuru is always placed at and using the (ISA) I/O-ports
+0xE0 and 0xE4, so we don't have to scan any port-range, just check what the two
+ports are holding for detection. We will refer to 0xE0 as CMD (command-port)
+and 0xE4 as DATA because Abit refers to them with these names.
+
+If DATA holds 0x00 or 0x08 and CMD holds 0x00 or 0xAC an uGuru could be
+present. We have to check for two different values at data-port, because
+after a reboot uGuru will hold 0x00 here, but if the driver is removed and
+later on attached again data-port will hold 0x08, more about this later.
+
+After wider testing of the Linux kernel driver some variants of the uGuru have
+turned up which will hold 0x00 instead of 0xAC at the CMD port, thus we also
+have to test CMD for two different values. On these uGuru's DATA will initally
+hold 0x09 and will only hold 0x08 after reading CMD first, so CMD must be read
+first!
+
+To be really sure an uGuru is present a test read of one or more register
+sets should be done.
+
+
+Reading / Writing
+=================
+
+Addressing
+----------
+
+The uGuru has a number of different addressing levels. The first addressing
+level we will call banks. A bank holds data for one or more sensors. The data
+in a bank for a sensor is one or more bytes large.
+
+The number of bytes is fixed for a given bank, you should always read or write
+that many bytes, reading / writing more will fail, the results when writing
+less then the number of bytes for a given bank are undetermined.
+
+See below for all known bank addresses, numbers of sensors in that bank,
+number of bytes data per sensor and contents/meaning of those bytes.
+
+Although both this document and the kernel driver have kept the sensor
+terminoligy for the addressing within a bank this is not 100% correct, in
+bank 0x24 for example the addressing within the bank selects a PWM output not
+a sensor.
+
+Notice that some banks have both a read and a write address this is how the
+uGuru determines if a read from or a write to the bank is taking place, thus
+when reading you should always use the read address and when writing the
+write address. The write address is always one (1) more then the read address.
+
+
+uGuru ready
+-----------
+
+Before you can read from or write to the uGuru you must first put the uGuru
+in "ready" mode.
+
+To put the uGuru in ready mode first write 0x00 to DATA and then wait for DATA
+to hold 0x09, DATA should read 0x09 within 250 read cycles.
+
+Next CMD _must_ be read and should hold 0xAC, usually CMD will hold 0xAC the
+first read but sometimes it takes a while before CMD holds 0xAC and thus it
+has to be read a number of times (max 50).
+
+After reading CMD, DATA should hold 0x08 which means that the uGuru is ready
+for input. As above DATA will usually hold 0x08 the first read but not always.
+This step can be skipped, but it is undetermined what happens if the uGuru has
+not yet reported 0x08 at DATA and you proceed with writing a bank address.
+
+
+Sending bank and sensor addresses to the uGuru
+----------------------------------------------
+
+First the uGuru must be in "ready" mode as described above, DATA should hold
+0x08 indicating that the uGuru wants input, in this case the bank address.
+
+Next write the bank address to DATA. After the bank address has been written
+wait for to DATA to hold 0x08 again indicating that it wants / is ready for
+more input (max 250 reads).
+
+Once DATA holds 0x08 again write the sensor address to CMD.
+
+
+Reading
+-------
+
+First send the bank and sensor addresses as described above.
+Then for each byte of data you want to read wait for DATA to hold 0x01
+which indicates that the uGuru is ready to be read (max 250 reads) and once
+DATA holds 0x01 read the byte from CMD.
+
+Once all bytes have been read data will hold 0x09, but there is no reason to
+test for this. Notice that the number of bytes is bank address dependent see
+above and below.
+
+After completing a successfull read it is advised to put the uGuru back in
+ready mode, so that it is ready for the next read / write cycle. This way
+if your program / driver is unloaded and later loaded again the detection
+algorithm described above will still work.
+
+
+
+Writing
+-------
+
+First send the bank and sensor addresses as described above.
+Then for each byte of data you want to write wait for DATA to hold 0x00
+which indicates that the uGuru is ready to be written (max 250 reads) and
+once DATA holds 0x00 write the byte to CMD.
+
+Once all bytes have been written wait for DATA to hold 0x01 (max 250 reads)
+don't ask why this is the way it is.
+
+Once DATA holds 0x01 read CMD it should hold 0xAC now.
+
+After completing a successfull write it is advised to put the uGuru back in
+ready mode, so that it is ready for the next read / write cycle. This way
+if your program / driver is unloaded and later loaded again the detection
+algorithm described above will still work.
+
+
+Gotchas
+-------
+
+After wider testing of the Linux kernel driver some variants of the uGuru have
+turned up which do not hold 0x08 at DATA within 250 reads after writing the
+bank address. With these versions this happens quite frequent, using larger
+timeouts doesn't help, they just go offline for a second or 2, doing some
+internal callibration or whatever. Your code should be prepared to handle
+this and in case of no response in this specific case just goto sleep for a
+while and then retry.
+
+
+Address Map
+===========
+
+Bank 0x20 Alarms (R)
+--------------------
+This bank contains 0 sensors, iow the sensor address is ignored (but must be
+written) just use 0. Bank 0x20 contains 3 bytes:
+
+Byte 0:
+This byte holds the alarm flags for sensor 0-7 of Sensor Bank1, with bit 0
+corresponding to sensor 0, 1 to 1, etc.
+
+Byte 1:
+This byte holds the alarm flags for sensor 8-15 of Sensor Bank1, with bit 0
+corresponding to sensor 8, 1 to 9, etc.
+
+Byte 2:
+This byte holds the alarm flags for sensor 0-5 of Sensor Bank2, with bit 0
+corresponding to sensor 0, 1 to 1, etc.
+
+
+Bank 0x21 Sensor Bank1 Values / Readings (R)
+--------------------------------------------
+This bank contains 16 sensors, for each sensor it contains 1 byte.
+So far the following sensors are known to be available on all motherboards:
+Sensor  0 CPU temp
+Sensor  1 SYS temp
+Sensor  3 CPU core volt
+Sensor  4 DDR volt
+Sensor 10 DDR Vtt volt
+Sensor 15 PWM temp
+
+Byte 0:
+This byte holds the reading from the sensor. Sensors in Bank1 can be both
+volt and temp sensors, this is motherboard specific. The uGuru however does
+seem to know (be programmed with) what kindoff sensor is attached see Sensor
+Bank1 Settings description.
+
+Volt sensors use a linear scale, a reading 0 corresponds with 0 volt and a
+reading of 255 with 3494 mV. The sensors for higher voltages however are
+connected through a division circuit. The currently known division circuits
+in use result in ranges of: 0-4361mV, 0-6248mV or 0-14510mV. 3.3 volt sources
+use the 0-4361mV range, 5 volt the 0-6248mV and 12 volt the 0-14510mV .
+
+Temp sensors also use a linear scale, a reading of 0 corresponds with 0 degree
+Celsius and a reading of 255 with a reading of 255 degrees Celsius.
+
+
+Bank 0x22 Sensor Bank1 Settings (R)
+Bank 0x23 Sensor Bank1 Settings (W)
+-----------------------------------
+
+This bank contains 16 sensors, for each sensor it contains 3 bytes. Each
+set of 3 bytes contains the settings for the sensor with the same sensor
+address in Bank 0x21 .
+
+Byte 0:
+Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
+Bit 0: Give an alarm if measured temp is over the warning threshold	(RW) *
+Bit 1: Give an alarm if measured volt is over the max threshold		(RW) **
+Bit 2: Give an alarm if measured volt is under the min threshold	(RW) **
+Bit 3: Beep if alarm							(RW)
+Bit 4: 1 if alarm cause measured temp is over the warning threshold	(R)
+Bit 5: 1 if alarm cause measured volt is over the max threshold		(R)
+Bit 6: 1 if alarm cause measured volt is under the min threshold	(R)
+Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds	(RW)
+       Temp sensor: Shutdown if temp is over the shutdown threshold	(RW)
+
+*  This bit is only honored/used by the uGuru if a temp sensor is connected
+** This bit is only honored/used by the uGuru if a volt sensor is connected
+Note with some trickery this can be used to find out what kinda sensor is
+detected see the Linux kernel driver for an example with many comments on
+how todo this.
+
+Byte 1:
+Temp sensor: warning threshold  (scale as bank 0x21)
+Volt sensor: min threshold      (scale as bank 0x21)
+
+Byte 2:
+Temp sensor: shutdown threshold (scale as bank 0x21)
+Volt sensor: max threshold      (scale as bank 0x21)
+
+
+Bank 0x24 PWM outputs for FAN's (R)
+Bank 0x25 PWM outputs for FAN's (W)
+-----------------------------------
+
+This bank contains 3 "sensors", for each sensor it contains 5 bytes.
+Sensor 0 usually controls the CPU fan
+Sensor 1 usually controls the NB (or chipset for single chip) fan
+Sensor 2 usually controls the System fan
+
+Byte 0:
+Flag 0x80 to enable control, Fan runs at 100% when disabled.
+low nibble (temp)sensor address at bank 0x21 used for control.
+
+Byte 1:
+0-255 = 0-12v (linear), specify voltage at which fan will rotate when under
+low threshold temp (specified in byte 3)
+
+Byte 2:
+0-255 = 0-12v (linear), specify voltage at which fan will rotate when above
+high threshold temp (specified in byte 4)
+
+Byte 3:
+Low threshold temp  (scale as bank 0x21)
+
+byte 4:
+High threshold temp (scale as bank 0x21)
+
+
+Bank 0x26 Sensors Bank2 Values / Readings (R)
+---------------------------------------------
+
+This bank contains 6 sensors (AFAIK), for each sensor it contains 1 byte.
+So far the following sensors are known to be available on all motherboards:
+Sensor 0: CPU fan speed
+Sensor 1: NB (or chipset for single chip) fan speed
+Sensor 2: SYS fan speed
+
+Byte 0:
+This byte holds the reading from the sensor. 0-255 = 0-15300 (linear)
+
+
+Bank 0x27 Sensors Bank2 Settings (R)
+Bank 0x28 Sensors Bank2 Settings (W)
+------------------------------------
+
+This bank contains 6 sensors (AFAIK), for each sensor it contains 2 bytes.
+
+Byte 0:
+Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
+Bit 0: Give an alarm if measured rpm is under the min threshold	(RW)
+Bit 3: Beep if alarm						(RW)
+Bit 7: Shutdown if alarm persist for more then 4 seconds	(RW)
+
+Byte 1:
+min threshold (scale as bank 0x26)
+
+
+Warning for the adventerous
+===========================
+
+A word of caution to those who want to experiment and see if they can figure
+the voltage / clock programming out, I tried reading and only reading banks
+0-0x30 with the reading code used for the sensor banks (0x20-0x28) and this
+resulted in a _permanent_ reprogramming of the voltages, luckily I had the
+sensors part configured so that it would shutdown my system on any out of spec
+voltages which proprably safed my computer (after a reboot I managed to
+immediatly enter the bios and reload the defaults). This probably means that
+the read/write cycle for the non sensor part is different from the sensor part.
diff --git a/Documentation/hwmon/lm70 b/Documentation/hwmon/lm70
new file mode 100644
index 00000000000..2bdd3feebf5
--- /dev/null
+++ b/Documentation/hwmon/lm70
@@ -0,0 +1,31 @@
+Kernel driver lm70
+==================
+
+Supported chip:
+  * National Semiconductor LM70
+    Datasheet: http://www.national.com/pf/LM/LM70.html
+
+Author:
+        Kaiwan N Billimoria <kaiwan@designergraphix.com>
+
+Description
+-----------
+
+This driver implements support for the National Semiconductor LM70
+temperature sensor.
+
+The LM70 temperature sensor chip supports a single temperature sensor.
+It communicates with a host processor (or microcontroller) via an
+SPI/Microwire Bus interface.
+
+Communication with the LM70 is simple: when the temperature is to be sensed,
+the driver accesses the LM70 using SPI communication: 16 SCLK cycles
+comprise the MOSI/MISO loop. At the end of the transfer, the 11-bit 2's
+complement digital temperature (sent via the SIO line), is available in the
+driver for interpretation. This driver makes use of the kernel's in-core
+SPI support.
+
+Thanks to
+---------
+Jean Delvare <khali@linux-fr.org> for mentoring the hwmon-side driver
+development.
diff --git a/Documentation/hwmon/lm83 b/Documentation/hwmon/lm83
index 061d9ed8ff4..f7aad1489cb 100644
--- a/Documentation/hwmon/lm83
+++ b/Documentation/hwmon/lm83
@@ -7,6 +7,10 @@ Supported chips:
     Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e
     Datasheet: Publicly available at the National Semiconductor website
                http://www.national.com/pf/LM/LM83.html
+  * National Semiconductor LM82
+    Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e
+    Datasheet: Publicly available at the National Semiconductor website
+               http://www.national.com/pf/LM/LM82.html
 
 
 Author: Jean Delvare <khali@linux-fr.org>
@@ -15,10 +19,11 @@ Description
 -----------
 
 The LM83 is a digital temperature sensor. It senses its own temperature as
-well as the temperature of up to three external diodes. It is compatible
-with many other devices such as the LM84 and all other ADM1021 clones.
-The main difference between the LM83 and the LM84 in that the later can
-only sense the temperature of one external diode.
+well as the temperature of up to three external diodes. The LM82 is
+a stripped down version of the LM83 that only supports one external diode.
+Both are compatible with many other devices such as the LM84 and all
+other ADM1021 clones. The main difference between the LM83 and the LM84
+in that the later can only sense the temperature of one external diode.
 
 Using the adm1021 driver for a LM83 should work, but only two temperatures
 will be reported instead of four.
@@ -30,12 +35,16 @@ contact us. Note that the LM90 can easily be misdetected as a LM83.
 
 Confirmed motherboards:
     SBS         P014
+    SBS         PSL09
 
 Unconfirmed motherboards:
     Gigabyte    GA-8IK1100
     Iwill       MPX2
     Soltek      SL-75DRV5
 
+The LM82 is confirmed to have been found on most AMD Geode reference
+designs and test platforms.
+
 The driver has been successfully tested by Magnus Forsström, who I'd
 like to thank here. More testers will be of course welcome.
 
diff --git a/Documentation/hwmon/smsc47m192 b/Documentation/hwmon/smsc47m192
new file mode 100644
index 00000000000..45d6453cd43
--- /dev/null
+++ b/Documentation/hwmon/smsc47m192
@@ -0,0 +1,102 @@
+Kernel driver smsc47m192
+========================
+
+Supported chips:
+  * SMSC LPC47M192 and LPC47M997
+    Prefix: 'smsc47m192'
+    Addresses scanned: I2C 0x2c - 0x2d
+    Datasheet: The datasheet for LPC47M192 is publicly available from
+               http://www.smsc.com/
+               The LPC47M997 is compatible for hardware monitoring.
+
+Author: Hartmut Rick <linux@rick.claranet.de>
+        Special thanks to Jean Delvare for careful checking
+        of the code and many helpful comments and suggestions.
+
+
+Description
+-----------
+
+This driver implements support for the hardware sensor capabilities
+of the SMSC LPC47M192 and LPC47M997 Super-I/O chips.
+
+These chips support 3 temperature channels and 8 voltage inputs
+as well as CPU voltage VID input.
+
+They do also have fan monitoring and control capabilities, but the
+these features are accessed via ISA bus and are not supported by this
+driver. Use the 'smsc47m1' driver for fan monitoring and control.
+
+Voltages and temperatures are measured by an 8-bit ADC, the resolution
+of the temperatures is 1 bit per degree C.
+Voltages are scaled such that the nominal voltage corresponds to
+192 counts, i.e. 3/4 of the full range. Thus the available range for
+each voltage channel is 0V ... 255/192*(nominal voltage), the resolution
+is 1 bit per (nominal voltage)/192.
+Both voltage and temperature values are scaled by 1000, the sys files
+show voltages in mV and temperatures in units of 0.001 degC.
+
+The +12V analog voltage input channel (in4_input) is multiplexed with
+bit 4 of the encoded CPU voltage. This means that you either get
+a +12V voltage measurement or a 5 bit CPU VID, but not both.
+The default setting is to use the pin as 12V input, and use only 4 bit VID.
+This driver assumes that the information in the configuration register
+is correct, i.e. that the BIOS has updated the configuration if
+the motherboard has this input wired to VID4.
+
+The temperature and voltage readings are updated once every 1.5 seconds.
+Reading them more often repeats the same values.
+
+
+sysfs interface
+---------------
+
+in0_input	- +2.5V voltage input
+in1_input	- CPU voltage input (nominal 2.25V)
+in2_input	- +3.3V voltage input
+in3_input	- +5V voltage input
+in4_input	- +12V voltage input (may be missing if used as VID4)
+in5_input	- Vcc voltage input (nominal 3.3V)
+		  This is the supply voltage of the sensor chip itself.
+in6_input	- +1.5V voltage input
+in7_input	- +1.8V voltage input
+
+in[0-7]_min,
+in[0-7]_max	- lower and upper alarm thresholds for in[0-7]_input reading
+
+		  All voltages are read and written in mV.
+
+in[0-7]_alarm	- alarm flags for voltage inputs
+		  These files read '1' in case of alarm, '0' otherwise.
+
+temp1_input	- chip temperature measured by on-chip diode
+temp[2-3]_input	- temperature measured by external diodes (one of these would
+		  typically be wired to the diode inside the CPU)
+
+temp[1-3]_min,
+temp[1-3]_max	- lower and upper alarm thresholds for temperatures
+
+temp[1-3]_offset - temperature offset registers
+		  The chip adds the offsets stored in these registers to
+		  the corresponding temperature readings.
+		  Note that temp1 and temp2 offsets share the same register,
+		  they cannot both be different from zero at the same time.
+		  Writing a non-zero number to one of them will reset the other
+		  offset to zero.
+
+		  All temperatures and offsets are read and written in
+		  units of 0.001 degC.
+
+temp[1-3]_alarm - alarm flags for temperature inputs, '1' in case of alarm,
+		  '0' otherwise.
+temp[2-3]_input_fault - diode fault flags for temperature inputs 2 and 3.
+		  A fault is detected if the two pins for the corresponding
+		  sensor are open or shorted, or any of the two is shorted
+		  to ground or Vcc. '1' indicates a diode fault.
+
+cpu0_vid	- CPU voltage as received from the CPU
+
+vrm		- CPU VID standard used for decoding CPU voltage
+
+		  The *_min, *_max, *_offset and vrm files can be read and
+		  written, all others are read-only.
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index a0d0ab24288..d1d390aaf62 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -3,15 +3,15 @@ Naming and data format standards for sysfs files
 
 The libsensors library offers an interface to the raw sensors data
 through the sysfs interface. See libsensors documentation and source for
-more further information. As of writing this document, libsensors
-(from lm_sensors 2.8.3) is heavily chip-dependant. Adding or updating
+further information. As of writing this document, libsensors
+(from lm_sensors 2.8.3) is heavily chip-dependent. Adding or updating
 support for any given chip requires modifying the library's code.
 This is because libsensors was written for the procfs interface
 older kernel modules were using, which wasn't standardized enough.
 Recent versions of libsensors (from lm_sensors 2.8.2 and later) have
 support for the sysfs interface, though.
 
-The new sysfs interface was designed to be as chip-independant as
+The new sysfs interface was designed to be as chip-independent as
 possible.
 
 Note that motherboards vary widely in the connections to sensor chips.
@@ -24,7 +24,7 @@ range using external resistors. Since the values of these resistors
 can change from motherboard to motherboard, the conversions cannot be
 hard coded into the driver and have to be done in user space.
 
-For this reason, even if we aim at a chip-independant libsensors, it will
+For this reason, even if we aim at a chip-independent libsensors, it will
 still require a configuration file (e.g. /etc/sensors.conf) for proper
 values conversion, labeling of inputs and hiding of unused inputs.
 
@@ -39,15 +39,16 @@ If you are developing a userspace application please send us feedback on
 this standard.
 
 Note that this standard isn't completely established yet, so it is subject
-to changes, even important ones. One more reason to use the library instead
-of accessing sysfs files directly.
+to changes. If you are writing a new hardware monitoring driver those
+features can't seem to fit in this interface, please contact us with your
+extension proposal. Keep in mind that backward compatibility must be
+preserved.
 
 Each chip gets its own directory in the sysfs /sys/devices tree.  To
-find all sensor chips, it is easier to follow the symlinks from
-/sys/i2c/devices/
+find all sensor chips, it is easier to follow the device symlinks from
+/sys/class/hwmon/hwmon*.
 
-All sysfs values are fixed point numbers.  To get the true value of some
-of the values, you should divide by the specified value.
+All sysfs values are fixed point numbers.
 
 There is only one value per file, unlike the older /proc specification.
 The common scheme for files naming is: <type><number>_<item>. Usual
@@ -69,28 +70,40 @@ to cause an alarm) is chip-dependent.
 
 -------------------------------------------------------------------------
 
+[0-*]	denotes any positive number starting from 0
+[1-*]	denotes any positive number starting from 1
+RO	read only value
+RW	read/write value
+
+Read/write values may be read-only for some chips, depending on the
+hardware implementation.
+
+All entries are optional, and should only be created in a given driver
+if the chip has the feature.
+
 ************
 * Voltages *
 ************
 
-in[0-8]_min	Voltage min value.
+in[0-*]_min	Voltage min value.
 		Unit: millivolt
-		Read/Write
+		RW
 		
-in[0-8]_max	Voltage max value.
+in[0-*]_max	Voltage max value.
 		Unit: millivolt
-		Read/Write
+		RW
 		
-in[0-8]_input	Voltage input value.
+in[0-*]_input	Voltage input value.
 		Unit: millivolt
-		Read only
+		RO
+		Voltage measured on the chip pin.
 		Actual voltage depends on the scaling resistors on the
 		motherboard, as recommended in the chip datasheet.
 		This varies by chip and by motherboard.
 		Because of this variation, values are generally NOT scaled
 		by the chip driver, and must be done by the application.
 		However, some drivers (notably lm87 and via686a)
-		do scale, with various degrees of success.
+		do scale, because of internal resistors built into a chip.
 		These drivers will output the actual voltage.
 
 		Typical usage:
@@ -104,58 +117,72 @@ in[0-8]_input	Voltage input value.
 			in7_*	varies
 			in8_*	varies
 
-cpu[0-1]_vid	CPU core reference voltage.
+cpu[0-*]_vid	CPU core reference voltage.
 		Unit: millivolt
-		Read only.
+		RO
 		Not always correct.
 
 vrm		Voltage Regulator Module version number. 
-		Read only.
-		Two digit number, first is major version, second is
-		minor version.
+		RW (but changing it should no more be necessary)
+		Originally the VRM standard version multiplied by 10, but now
+		an arbitrary number, as not all standards have a version
+		number.
 		Affects the way the driver calculates the CPU core reference
 		voltage from the vid pins.
 
+Also see the Alarms section for status flags associated with voltages.
+
 
 ********
 * Fans *
 ********
 
-fan[1-3]_min	Fan minimum value
+fan[1-*]_min	Fan minimum value
 		Unit: revolution/min (RPM)
-		Read/Write.
+		RW
 
-fan[1-3]_input	Fan input value.
+fan[1-*]_input	Fan input value.
 		Unit: revolution/min (RPM)
-		Read only.
+		RO
 
-fan[1-3]_div	Fan divisor.
+fan[1-*]_div	Fan divisor.
 		Integer value in powers of two (1, 2, 4, 8, 16, 32, 64, 128).
+		RW
 		Some chips only support values 1, 2, 4 and 8.
 		Note that this is actually an internal clock divisor, which
 		affects the measurable speed range, not the read value.
 
+Also see the Alarms section for status flags associated with fans.
+
+
 *******
 * PWM *
 *******
 
-pwm[1-3]	Pulse width modulation fan control.
+pwm[1-*]	Pulse width modulation fan control.
 		Integer value in the range 0 to 255
-		Read/Write
+		RW
 		255 is max or 100%.
 
-pwm[1-3]_enable
+pwm[1-*]_enable
 		Switch PWM on and off.
 		Not always present even if fan*_pwm is.
-		0 to turn off
-		1 to turn on in manual mode
-		2 to turn on in automatic mode
-		Read/Write
+		0: turn off
+		1: turn on in manual mode
+		2+: turn on in automatic mode
+		Check individual chip documentation files for automatic mode details.
+		RW
+
+pwm[1-*]_mode
+		0: DC mode
+		1: PWM mode
+		RW
 
 pwm[1-*]_auto_channels_temp
 		Select which temperature channels affect this PWM output in
 		auto mode. Bitfield, 1 is temp1, 2 is temp2, 4 is temp3 etc...
 		Which values are possible depend on the chip used.
+		RW
 
 pwm[1-*]_auto_point[1-*]_pwm
 pwm[1-*]_auto_point[1-*]_temp
@@ -163,6 +190,7 @@ pwm[1-*]_auto_point[1-*]_temp_hyst
 		Define the PWM vs temperature curve. Number of trip points is
 		chip-dependent. Use this for chips which associate trip points
 		to PWM output channels.
+		RW
 
 OR
 
@@ -172,50 +200,57 @@ temp[1-*]_auto_point[1-*]_temp_hyst
 		Define the PWM vs temperature curve. Number of trip points is
 		chip-dependent. Use this for chips which associate trip points
 		to temperature channels.
+		RW
 
 
 ****************
 * Temperatures *
 ****************
 
-temp[1-3]_type	Sensor type selection.
+temp[1-*]_type	Sensor type selection.
 		Integers 1 to 4 or thermistor Beta value (typically 3435)
-		Read/Write.
+		RW
 		1: PII/Celeron Diode
 		2: 3904 transistor
 		3: thermal diode
 		4: thermistor (default/unknown Beta)
 		Not all types are supported by all chips
 
-temp[1-4]_max	Temperature max value.
-		Unit: millidegree Celcius
-		Read/Write value.
+temp[1-*]_max	Temperature max value.
+		Unit: millidegree Celsius (or millivolt, see below)
+		RW
 
-temp[1-3]_min	Temperature min value.
-		Unit: millidegree Celcius
-		Read/Write value.
+temp[1-*]_min	Temperature min value.
+		Unit: millidegree Celsius
+		RW
 
-temp[1-3]_max_hyst
+temp[1-*]_max_hyst
 		Temperature hysteresis value for max limit.
-		Unit: millidegree Celcius
+		Unit: millidegree Celsius
 		Must be reported as an absolute temperature, NOT a delta
 		from the max value.
-		Read/Write value.
+		RW
 
-temp[1-4]_input Temperature input value.
-		Unit: millidegree Celcius
-		Read only value.
+temp[1-*]_input Temperature input value.
+		Unit: millidegree Celsius
+		RO
 
-temp[1-4]_crit	Temperature critical value, typically greater than
+temp[1-*]_crit	Temperature critical value, typically greater than
 		corresponding temp_max values.
-		Unit: millidegree Celcius
-		Read/Write value.
+		Unit: millidegree Celsius
+		RW
 
-temp[1-2]_crit_hyst
+temp[1-*]_crit_hyst
 		Temperature hysteresis value for critical limit.
-		Unit: millidegree Celcius
+		Unit: millidegree Celsius
 		Must be reported as an absolute temperature, NOT a delta
 		from the critical value.
+		RW
+
+temp[1-4]_offset
+		Temperature offset which is added to the temperature reading
+		by the chip.
+		Unit: millidegree Celsius
 		Read/Write value.
 
 		If there are multiple temperature sensors, temp1_* is
@@ -225,6 +260,17 @@ temp[1-2]_crit_hyst
 		itself, for example the thermal diode inside the CPU or
 		a thermistor nearby.
 
+Some chips measure temperature using external thermistors and an ADC, and
+report the temperature measurement as a voltage. Converting this voltage
+back to a temperature (or the other way around for limits) requires
+mathematical functions not available in the kernel, so the conversion
+must occur in user space. For these chips, all temp* files described
+above should contain values expressed in millivolt instead of millidegree
+Celsius. In other words, such temperature channels are handled as voltage
+channels by the driver.
+
+Also see the Alarms section for status flags associated with temperatures.
+
 
 ************
 * Currents *
@@ -233,25 +279,88 @@ temp[1-2]_crit_hyst
 Note that no known chip provides current measurements as of writing,
 so this part is theoretical, so to say.
 
-curr[1-n]_max	Current max value
+curr[1-*]_max	Current max value
 		Unit: milliampere
-		Read/Write.
+		RW
 
-curr[1-n]_min	Current min value.
+curr[1-*]_min	Current min value.
 		Unit: milliampere
-		Read/Write.
+		RW
 
-curr[1-n]_input	Current input value
+curr[1-*]_input	Current input value
 		Unit: milliampere
-		Read only.
+		RO
 
 
-*********
-* Other *
-*********
+**********
+* Alarms *
+**********
+
+Each channel or limit may have an associated alarm file, containing a
+boolean value. 1 means than an alarm condition exists, 0 means no alarm.
+
+Usually a given chip will either use channel-related alarms, or
+limit-related alarms, not both. The driver should just reflect the hardware
+implementation.
+
+in[0-*]_alarm
+fan[1-*]_alarm
+temp[1-*]_alarm
+		Channel alarm
+		0: no alarm
+		1: alarm
+		RO
+
+OR
+
+in[0-*]_min_alarm
+in[0-*]_max_alarm
+fan[1-*]_min_alarm
+temp[1-*]_min_alarm
+temp[1-*]_max_alarm
+temp[1-*]_crit_alarm
+		Limit alarm
+		0: no alarm
+		1: alarm
+		RO
+
+Each input channel may have an associated fault file. This can be used
+to notify open diodes, unconnected fans etc. where the hardware
+supports it. When this boolean has value 1, the measurement for that
+channel should not be trusted.
+
+in[0-*]_input_fault
+fan[1-*]_input_fault
+temp[1-*]_input_fault
+		Input fault condition
+		0: no fault occured
+		1: fault condition
+		RO
+
+Some chips also offer the possibility to get beeped when an alarm occurs:
+
+beep_enable	Master beep enable
+		0: no beeps
+		1: beeps
+		RW
+
+in[0-*]_beep
+fan[1-*]_beep
+temp[1-*]_beep
+		Channel beep
+		0: disable
+		1: enable
+		RW
+
+In theory, a chip could provide per-limit beep masking, but no such chip
+was seen so far.
+
+Old drivers provided a different, non-standard interface to alarms and
+beeps. These interface files are deprecated, but will be kept around
+for compatibility reasons:
 
 alarms		Alarm bitmask.
-		Read only.
+		RO
 		Integer representation of one to four bytes.
 		A '1' bit means an alarm.
 		Chips should be programmed for 'comparator' mode so that
@@ -259,35 +368,26 @@ alarms		Alarm bitmask.
 		if it is still valid.
 		Generally a direct representation of a chip's internal
 		alarm registers; there is no standard for the position
-		of individual bits.
+		of individual bits. For this reason, the use of this
+		interface file for new drivers is discouraged. Use
+		individual *_alarm and *_fault files instead.
 		Bits are defined in kernel/include/sensors.h.
 
-alarms_in	Alarm bitmask relative to in (voltage) channels
-		Read only
-		A '1' bit means an alarm, LSB corresponds to in0 and so on
-		Prefered to 'alarms' for newer chips
-
-alarms_fan	Alarm bitmask relative to fan channels
-		Read only
-		A '1' bit means an alarm, LSB corresponds to fan1 and so on
-		Prefered to 'alarms' for newer chips
-
-alarms_temp	Alarm bitmask relative to temp (temperature) channels
-		Read only
-		A '1' bit means an alarm, LSB corresponds to temp1 and so on
-		Prefered to 'alarms' for newer chips
+beep_mask	Bitmask for beep.
+		Same format as 'alarms' with the same bit locations,
+		use discouraged for the same reason. Use individual
+		*_beep files instead.
+		RW
 
-beep_enable	Beep/interrupt enable
-		0 to disable.
-		1 to enable.
-		Read/Write
 
-beep_mask	Bitmask for beep.
-		Same format as 'alarms' with the same bit locations.
-		Read/Write
+*********
+* Other *
+*********
 
 eeprom		Raw EEPROM data in binary form.
-		Read only.
+		RO
 
 pec		Enable or disable PEC (SMBus only)
-		Read/Write
+		0: disable
+		1: enable
+		RW
diff --git a/Documentation/hwmon/userspace-tools b/Documentation/hwmon/userspace-tools
index 2622aac6542..19900a8fe67 100644
--- a/Documentation/hwmon/userspace-tools
+++ b/Documentation/hwmon/userspace-tools
@@ -6,31 +6,32 @@ voltages, fans speed). They are often connected through an I2C bus, but some
 are also connected directly through the ISA bus.
 
 The kernel drivers make the data from the sensor chips available in the /sys
-virtual filesystem. Userspace tools are then used to display or set or the
-data in a more friendly manner.
+virtual filesystem. Userspace tools are then used to display the measured
+values or configure the chips in a more friendly manner.
 
 Lm-sensors
 ----------
 
-Core set of utilites that will allow you to obtain health information,
+Core set of utilities that will allow you to obtain health information,
 setup monitoring limits etc. You can get them on their homepage
 http://www.lm-sensors.nu/ or as a package from your Linux distribution.
 
 If from website:
-Get lmsensors from project web site. Please note, you need only userspace
-part, so compile with "make user_install" target.
+Get lm-sensors from project web site. Please note, you need only userspace
+part, so compile with "make user" and install with "make user_install".
 
 General hints to get things working:
 
 0) get lm-sensors userspace utils
-1) compile all drivers in I2C section as modules in your kernel
+1) compile all drivers in I2C and Hardware Monitoring sections as modules
+   in your kernel
 2) run sensors-detect script, it will tell you what modules you need to load.
 3) load them and run "sensors" command, you should see some results.
 4) fix sensors.conf, labels, limits, fan divisors
 5) if any more problems consult FAQ, or documentation
 
-Other utilites
---------------
+Other utilities
+---------------
 
 If you want some graphical indicators of system health look for applications
 like: gkrellm, ksensors, xsensors, wmtemp, wmsensors, wmgtemp, ksysguardd,
diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d
new file mode 100644
index 00000000000..83a3836289c
--- /dev/null
+++ b/Documentation/hwmon/w83791d
@@ -0,0 +1,113 @@
+Kernel driver w83791d
+=====================
+
+Supported chips:
+  * Winbond W83791D
+    Prefix: 'w83791d'
+    Addresses scanned: I2C 0x2c - 0x2f
+    Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791Da.pdf
+
+Author: Charles Spirakis <bezaur@gmail.com>
+
+This driver was derived from the w83781d.c and w83792d.c source files.
+
+Credits:
+  w83781d.c:
+    Frodo Looijaard <frodol@dds.nl>,
+    Philip Edelbrock <phil@netroedge.com>,
+    and Mark Studebaker <mdsxyz123@yahoo.com>
+  w83792d.c:
+    Chunhao Huang <DZShen@Winbond.com.tw>,
+    Rudolf Marek <r.marek@sh.cvut.cz>
+
+Module Parameters
+-----------------
+
+* init boolean
+  (default 0)
+  Use 'init=1' to have the driver do extra software initializations.
+  The default behavior is to do the minimum initialization possible
+  and depend on the BIOS to properly setup the chip. If you know you
+  have a w83791d and you're having problems, try init=1 before trying
+  reset=1.
+
+* reset boolean
+  (default 0)
+  Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default
+  behavior is no chip reset to preserve BIOS settings.
+
+* force_subclients=bus,caddr,saddr,saddr
+  This is used to force the i2c addresses for subclients of
+  a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b'
+  to force the subclients of chip 0x2f on bus 0 to i2c addresses
+  0x4a and 0x4b.
+
+
+Description
+-----------
+
+This driver implements support for the Winbond W83791D chip.
+
+Detection of the chip can sometimes be foiled because it can be in an
+internal state that allows no clean access (Bank with ID register is not
+currently selected). If you know the address of the chip, use a 'force'
+parameter; this will put it into a more well-behaved state first.
+
+The driver implements three temperature sensors, five fan rotation speed
+sensors, and ten voltage sensors.
+
+Temperatures are measured in degrees Celsius and measurement resolution is 1
+degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
+the temperature gets higher than the Overtemperature Shutdown value; it stays
+on until the temperature falls below the Hysteresis value.
+
+Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
+triggered if the rotation speed has dropped below a programmable limit. Fan
+readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3
+and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more
+range or accuracy.
+
+Voltage sensors (also known as IN sensors) report their values in millivolts.
+An alarm is triggered if the voltage has crossed a programmable minimum
+or maximum limit.
+
+Alarms are provided as output from a "realtime status register". The
+following bits are defined:
+
+bit - alarm on:
+0  - Vcore
+1  - VINR0
+2  - +3.3VIN
+3  - 5VDD
+4  - temp1
+5  - temp2
+6  - fan1
+7  - fan2
+8  - +12VIN
+9  - -12VIN
+10 - -5VIN
+11 - fan3
+12 - chassis
+13 - temp3
+14 - VINR1
+15 - reserved
+16 - tart1
+17 - tart2
+18 - tart3
+19 - VSB
+20 - VBAT
+21 - fan4
+22 - fan5
+23 - reserved
+
+When an alarm goes off, you can be warned by a beeping signal through your
+computer speaker. It is possible to enable all beeping globally, or only
+the beeping for some alarms.
+
+The driver only reads the chip values each 3 seconds; reading them more
+often will do no harm, but will return 'old' values.
+
+W83791D TODO:
+---------------
+Provide a patch for per-file alarms as discussed on the mailing list
+Provide a patch for smart-fan control (still need appropriate motherboard/fans)
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index fd4b2712d57..e46c2345824 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -21,8 +21,7 @@ Authors:
 Module Parameters
 -----------------
 
-* force_addr: int
-  Forcibly enable the ICH at the given address. EXTREMELY DANGEROUS!
+None.
 
 
 Description
diff --git a/Documentation/i2c/busses/i2c-nforce2 b/Documentation/i2c/busses/i2c-nforce2
index d751282d9b2..cd49c428a3a 100644
--- a/Documentation/i2c/busses/i2c-nforce2
+++ b/Documentation/i2c/busses/i2c-nforce2
@@ -7,6 +7,8 @@ Supported adapters:
   * nForce3 250Gb MCP          10de:00E4 
   * nForce4 MCP                10de:0052
   * nForce4 MCP-04             10de:0034
+  * nForce4 MCP51              10de:0264
+  * nForce4 MCP55              10de:0368
 
 Datasheet: not publically available, but seems to be similar to the
            AMD-8111 SMBus 2.0 adapter.
diff --git a/Documentation/i2c/busses/i2c-ocores b/Documentation/i2c/busses/i2c-ocores
new file mode 100644
index 00000000000..cfcebb10d14
--- /dev/null
+++ b/Documentation/i2c/busses/i2c-ocores
@@ -0,0 +1,51 @@
+Kernel driver i2c-ocores
+
+Supported adapters:
+  * OpenCores.org I2C controller by Richard Herveille (see datasheet link)
+    Datasheet: http://www.opencores.org/projects.cgi/web/i2c/overview
+
+Author: Peter Korsgaard <jacmet@sunsite.dk>
+
+Description
+-----------
+
+i2c-ocores is an i2c bus driver for the OpenCores.org I2C controller
+IP core by Richard Herveille.
+
+Usage
+-----
+
+i2c-ocores uses the platform bus, so you need to provide a struct
+platform_device with the base address and interrupt number. The
+dev.platform_data of the device should also point to a struct
+ocores_i2c_platform_data (see linux/i2c-ocores.h) describing the
+distance between registers and the input clock speed.
+
+E.G. something like:
+
+static struct resource ocores_resources[] = {
+	[0] = {
+		.start	= MYI2C_BASEADDR,
+		.end	= MYI2C_BASEADDR + 8,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= MYI2C_IRQ,
+		.end	= MYI2C_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct ocores_i2c_platform_data myi2c_data = {
+	.regstep	= 2,		/* two bytes between registers */
+	.clock_khz	= 50000,	/* input clock of 50MHz */
+};
+
+static struct platform_device myi2c = {
+	.name			= "ocores-i2c",
+	.dev = {
+		.platform_data	= &myi2c_data,
+	},
+	.num_resources		= ARRAY_SIZE(ocores_resources),
+	.resource		= ocores_resources,
+};
diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4
index a1c8f581afe..92147633323 100644
--- a/Documentation/i2c/busses/i2c-piix4
+++ b/Documentation/i2c/busses/i2c-piix4
@@ -6,6 +6,8 @@ Supported adapters:
     Datasheet: Publicly available at the Intel website
   * ServerWorks OSB4, CSB5, CSB6 and HT-1000 southbridges
     Datasheet: Only available via NDA from ServerWorks
+  * ATI IXP southbridges IXP200, IXP300, IXP400
+    Datasheet: Not publicly available
   * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge
     Datasheet: Publicly available at the SMSC website http://www.smsc.com
 
@@ -21,8 +23,6 @@ Module Parameters
   Forcibly enable the PIIX4. DANGEROUS!
 * force_addr: int
   Forcibly enable the PIIX4 at the given address. EXTREMELY DANGEROUS!
-* fix_hstcfg: int
-  Fix config register. Needed on some boards (Force CPCI735).
 
 
 Description
@@ -63,10 +63,36 @@ The PIIX4E is just an new version of the PIIX4; it is supported as well.
 The PIIX/PIIX3 does not implement an SMBus or I2C bus, so you can't use
 this driver on those mainboards.
 
-The ServerWorks Southbridges, the Intel 440MX, and the Victory766 are
+The ServerWorks Southbridges, the Intel 440MX, and the Victory66 are
 identical to the PIIX4 in I2C/SMBus support.
 
-A few OSB4 southbridges are known to be misconfigured by the BIOS. In this
-case, you have you use the fix_hstcfg module parameter. Do not use it
-unless you know you have to, because in some cases it also breaks
-configuration on southbridges that don't need it.
+If you own Force CPCI735 motherboard or other OSB4 based systems you may need
+to change the SMBus Interrupt Select register so the SMBus controller uses
+the SMI mode.
+
+1) Use lspci command and locate the PCI device with the SMBus controller:
+   00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 4f)
+   The line may vary for different chipsets. Please consult the driver source
+   for all possible PCI ids (and lspci -n to match them). Lets assume the
+   device is located at 00:0f.0.
+2) Now you just need to change the value in 0xD2 register. Get it first with
+   command: lspci -xxx -s 00:0f.0
+   If the value is 0x3 then you need to change it to 0x1
+   setpci  -s 00:0f.0 d2.b=1
+
+Please note that you don't need to do that in all cases, just when the SMBus is
+not working properly.
+
+
+Hardware-specific issues
+------------------------
+
+This driver will refuse to load on IBM systems with an Intel PIIX4 SMBus.
+Some of these machines have an RFID EEPROM (24RF08) connected to the SMBus,
+which can easily get corrupted due to a state machine bug. These are mostly
+Thinkpad laptops, but desktop systems may also be affected. We have no list
+of all affected systems, so the only safe solution was to prevent access to
+the SMBus on all IBM systems (detected using DMI data.)
+
+For additional information, read:
+http://www2.lm-sensors.nu/~lm78/cvs/lm_sensors2/README.thinkpad
diff --git a/Documentation/i2c/busses/scx200_acb b/Documentation/i2c/busses/scx200_acb
index f50e69981ec..7c07883d4df 100644
--- a/Documentation/i2c/busses/scx200_acb
+++ b/Documentation/i2c/busses/scx200_acb
@@ -2,14 +2,31 @@ Kernel driver scx200_acb
 
 Author: Christer Weinigel <wingel@nano-system.com>
 
+The driver supersedes the older, never merged driver named i2c-nscacb.
+
 Module Parameters
 -----------------
 
-* base: int
+* base: up to 4 ints
   Base addresses for the ACCESS.bus controllers on SCx200 and SC1100 devices
 
+  By default the driver uses two base addresses 0x820 and 0x840.
+  If you want only one base address, specify the second as 0 so as to
+  override this default.
+
 Description
 -----------
 
 Enable the use of the ACCESS.bus controller on the Geode SCx200 and
 SC1100 processors and the CS5535 and CS5536 Geode companion devices.
+
+Device-specific notes
+---------------------
+
+The SC1100 WRAP boards are known to use base addresses 0x810 and 0x820.
+If the scx200_acb driver is built into the kernel, add the following
+parameter to your boot command line:
+  scx200_acb.base=0x810,0x820
+If the scx200_acb driver is built as a module, add the following line to
+the file /etc/modprobe.conf instead:
+  options scx200_acb base=0x810,0x820
diff --git a/MAINTAINERS b/MAINTAINERS
index d10e629db56..f4cf0148c90 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -181,6 +181,12 @@ M:	bcrl@kvack.org
 L:	linux-aio@kvack.org
 S:	Supported
 
+ABIT UGURU HARDWARE MONITOR DRIVER
+P:	Hans de Goede
+M:	j.w.r.degoede@hhs.nl
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+
 ACENIC DRIVER
 P:	Jes Sorensen
 M:	jes@trained-monkey.org
@@ -2057,6 +2063,12 @@ M:      adaplas@pol.net
 L:      linux-fbdev-devel@lists.sourceforge.net
 S:      Maintained
 
+OPENCORES I2C BUS DRIVER
+P:	Peter Korsgaard
+M:	jacmet@sunsite.dk
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+
 ORACLE CLUSTER FILESYSTEM 2 (OCFS2)
 P:	Mark Fasheh
 M:	mark.fasheh@oracle.com
@@ -2528,12 +2540,6 @@ M:	thomas@winischhofer.net
 W:	http://www.winischhofer.at/linuxsisusbvga.shtml
 S:	Maintained
 
-SMSC47M1 HARDWARE MONITOR DRIVER
-P:	Jean Delvare
-M:	khali@linux-fr.org
-L:	lm-sensors@lm-sensors.org
-S:	Odd Fixes
-
 SMB FILESYSTEM
 P:	Urban Widmark
 M:	urban@teststation.com
@@ -3146,12 +3152,6 @@ L:	wbsd-devel@list.drzeus.cx
 W:	http://projects.drzeus.cx/wbsd
 S:	Maintained
 
-W83L785TS HARDWARE MONITOR DRIVER
-P:	Jean Delvare
-M:	khali@linux-fr.org
-L:	lm-sensors@lm-sensors.org
-S:	Odd Fixes
-
 WATCHDOG DEVICE DRIVERS
 P:	Wim Van Sebroeck
 M:	wim@iguana.be
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 99cdc612d2c..0e31a0c496e 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1,5 +1,5 @@
 #
-# I2C Sensor chip drivers configuration
+# Hardware monitoring chip drivers configuration
 #
 
 menu "Hardware Monitoring support"
@@ -16,6 +16,10 @@ config HWMON
 	  should say Y here and also to the specific driver(s) for your
 	  sensors chip(s) below.
 
+	  To find out which specific driver(s) you need, use the
+	  sensors-detect script from the lm_sensors package.  Read
+	  <file:Documentation/hwmon/userspace-tools> for details.
+
 	  This support can also be built as a module.  If so, the module
 	  will be called hwmon.
 
@@ -23,6 +27,18 @@ config HWMON_VID
 	tristate
 	default n
 
+config SENSORS_ABITUGURU
+	tristate "Abit uGuru"
+	depends on HWMON && EXPERIMENTAL
+	help
+	  If you say yes here you get support for the Abit uGuru chips
+	  sensor part. The voltage and frequency control parts of the Abit
+	  uGuru are not supported. The Abit uGuru chip can be found on Abit
+	  uGuru featuring motherboards (most modern Abit motherboards).
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called abituguru.
+
 config SENSORS_ADM1021
 	tristate "Analog Devices ADM1021 and compatibles"
 	depends on HWMON && I2C
@@ -188,6 +204,16 @@ config SENSORS_LM63
 	  This driver can also be built as a module.  If so, the module
 	  will be called lm63.
 
+config SENSORS_LM70
+	tristate "National Semiconductor LM70"
+	depends on HWMON && SPI_MASTER && EXPERIMENTAL
+	help
+	  If you say yes here you get support for the National Semiconductor
+	  LM70 digital temperature sensor chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called lm70.
+
 config SENSORS_LM75
 	tristate "National Semiconductor LM75 and compatibles"
 	depends on HWMON && I2C
@@ -236,11 +262,11 @@ config SENSORS_LM80
 	  will be called lm80.
 
 config SENSORS_LM83
-	tristate "National Semiconductor LM83"
+	tristate "National Semiconductor LM83 and compatibles"
 	depends on HWMON && I2C
 	help
 	  If you say yes here you get support for National Semiconductor
-	  LM83 sensor chips.
+	  LM82 and LM83 sensor chips.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called lm83.
@@ -333,11 +359,32 @@ config SENSORS_SMSC47M1
 	help
 	  If you say yes here you get support for the integrated fan
 	  monitoring and control capabilities of the SMSC LPC47B27x,
-	  LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x and LPC47M192 chips.
+	  LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x, LPC47M192 and
+	  LPC47M997 chips.
+
+	  The temperature and voltage sensor features of the LPC47M192
+	  and LPC47M997 are supported by another driver, select also
+	  "SMSC LPC47M192 and compatibles" below for those.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called smsc47m1.
 
+config SENSORS_SMSC47M192
+	tristate "SMSC LPC47M192 and compatibles"
+	depends on HWMON && I2C && EXPERIMENTAL
+	select HWMON_VID
+	help
+	  If you say yes here you get support for the temperature and
+	  voltage sensors of the SMSC LPC47M192 and LPC47M997 chips.
+
+	  The fan monitoring and control capabilities of these chips
+	  are supported by another driver, select
+	  "SMSC LPC47M10x and compatibles" above. You need both drivers
+	  if you want fan control and voltage/temperature sensor support.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called smsc47m192.
+
 config SENSORS_SMSC47B397
 	tristate "SMSC LPC47B397-NC"
 	depends on HWMON && I2C && EXPERIMENTAL
@@ -385,6 +432,16 @@ config SENSORS_W83781D
 	  This driver can also be built as a module.  If so, the module
 	  will be called w83781d.
 
+config SENSORS_W83791D
+	tristate "Winbond W83791D"
+	depends on HWMON && I2C && EXPERIMENTAL
+	select HWMON_VID
+	help
+	  If you say yes here you get support for the Winbond W83791D chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called w83791d.
+
 config SENSORS_W83792D
 	tristate "Winbond W83792D"
 	depends on HWMON && I2C && EXPERIMENTAL
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index fbdb8d911a7..31415843a91 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -10,7 +10,9 @@ obj-$(CONFIG_SENSORS_ASB100)	+= asb100.o
 obj-$(CONFIG_SENSORS_W83627HF)	+= w83627hf.o
 obj-$(CONFIG_SENSORS_W83792D)	+= w83792d.o
 obj-$(CONFIG_SENSORS_W83781D)	+= w83781d.o
+obj-$(CONFIG_SENSORS_W83791D)	+= w83791d.o
 
+obj-$(CONFIG_SENSORS_ABITUGURU)	+= abituguru.o
 obj-$(CONFIG_SENSORS_ADM1021)	+= adm1021.o
 obj-$(CONFIG_SENSORS_ADM1025)	+= adm1025.o
 obj-$(CONFIG_SENSORS_ADM1026)	+= adm1026.o
@@ -26,6 +28,7 @@ obj-$(CONFIG_SENSORS_GL520SM)	+= gl520sm.o
 obj-$(CONFIG_SENSORS_HDAPS)	+= hdaps.o
 obj-$(CONFIG_SENSORS_IT87)	+= it87.o
 obj-$(CONFIG_SENSORS_LM63)	+= lm63.o
+obj-$(CONFIG_SENSORS_LM70)	+= lm70.o
 obj-$(CONFIG_SENSORS_LM75)	+= lm75.o
 obj-$(CONFIG_SENSORS_LM77)	+= lm77.o
 obj-$(CONFIG_SENSORS_LM78)	+= lm78.o
@@ -40,6 +43,7 @@ obj-$(CONFIG_SENSORS_PC87360)	+= pc87360.o
 obj-$(CONFIG_SENSORS_SIS5595)	+= sis5595.o
 obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
 obj-$(CONFIG_SENSORS_SMSC47M1)	+= smsc47m1.o
+obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
 obj-$(CONFIG_SENSORS_VIA686A)	+= via686a.o
 obj-$(CONFIG_SENSORS_VT8231)	+= vt8231.o
 obj-$(CONFIG_SENSORS_W83627EHF)	+= w83627ehf.o
diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c
new file mode 100644
index 00000000000..59122cc0a50
--- /dev/null
+++ b/drivers/hwmon/abituguru.c
@@ -0,0 +1,1415 @@
+/*
+    abituguru.c Copyright (c) 2005-2006 Hans de Goede <j.w.r.degoede@hhs.nl>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+/*
+    This driver supports the sensor part of the custom Abit uGuru chip found
+    on Abit uGuru motherboards. Note: because of lack of specs the CPU / RAM /
+    etc voltage & frequency control is not supported!
+*/
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <asm/io.h>
+
+/* Banks */
+#define ABIT_UGURU_ALARM_BANK			0x20 /* 1x 3 bytes */
+#define ABIT_UGURU_SENSOR_BANK1			0x21 /* 16x volt and temp */
+#define ABIT_UGURU_FAN_PWM			0x24 /* 3x 5 bytes */
+#define ABIT_UGURU_SENSOR_BANK2			0x26 /* fans */
+/* max nr of sensors in bank1, a bank1 sensor can be in, temp or nc */
+#define ABIT_UGURU_MAX_BANK1_SENSORS		16
+/* Warning if you increase one of the 2 MAX defines below to 10 or higher you
+   should adjust the belonging _NAMES_LENGTH macro for the 2 digit number! */
+/* max nr of sensors in bank2, currently mb's with max 6 fans are known */
+#define ABIT_UGURU_MAX_BANK2_SENSORS		6
+/* max nr of pwm outputs, currently mb's with max 5 pwm outputs are known */
+#define ABIT_UGURU_MAX_PWMS			5
+/* uGuru sensor bank 1 flags */			     /* Alarm if: */
+#define ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE	0x01 /*  temp over warn */
+#define ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE	0x02 /*  volt over max */
+#define ABIT_UGURU_VOLT_LOW_ALARM_ENABLE	0x04 /*  volt under min */
+#define ABIT_UGURU_TEMP_HIGH_ALARM_FLAG		0x10 /* temp is over warn */
+#define ABIT_UGURU_VOLT_HIGH_ALARM_FLAG		0x20 /* volt is over max */
+#define ABIT_UGURU_VOLT_LOW_ALARM_FLAG		0x40 /* volt is under min */
+/* uGuru sensor bank 2 flags */			     /* Alarm if: */
+#define ABIT_UGURU_FAN_LOW_ALARM_ENABLE		0x01 /*   fan under min */
+/* uGuru sensor bank common flags */
+#define ABIT_UGURU_BEEP_ENABLE			0x08 /* beep if alarm */
+#define ABIT_UGURU_SHUTDOWN_ENABLE		0x80 /* shutdown if alarm */
+/* uGuru fan PWM (speed control) flags */
+#define ABIT_UGURU_FAN_PWM_ENABLE		0x80 /* enable speed control */
+/* Values used for conversion */
+#define ABIT_UGURU_FAN_MAX			15300 /* RPM */
+/* Bank1 sensor types */
+#define ABIT_UGURU_IN_SENSOR			0
+#define ABIT_UGURU_TEMP_SENSOR			1
+#define ABIT_UGURU_NC				2
+/* Timeouts / Retries, if these turn out to need a lot of fiddling we could
+   convert them to params. */
+/* 250 was determined by trial and error, 200 works most of the time, but not
+   always. I assume this is cpu-speed independent, since the ISA-bus and not
+   the CPU should be the bottleneck. Note that 250 sometimes is still not
+   enough (only reported on AN7 mb) this is handled by a higher layer. */
+#define ABIT_UGURU_WAIT_TIMEOUT			250
+/* Normally all expected status in abituguru_ready, are reported after the
+   first read, but sometimes not and we need to poll, 5 polls was not enough
+   50 sofar is. */
+#define ABIT_UGURU_READY_TIMEOUT		50
+/* Maximum 3 retries on timedout reads/writes, delay 200 ms before retrying */
+#define ABIT_UGURU_MAX_RETRIES			3
+#define ABIT_UGURU_RETRY_DELAY			(HZ/5)
+/* Maximum 2 timeouts in abituguru_update_device, iow 3 in a row is an error */
+#define ABIT_UGURU_MAX_TIMEOUTS			2
+/* utility macros */
+#define ABIT_UGURU_NAME				"abituguru"
+#define ABIT_UGURU_DEBUG(level, format, arg...)				\
+	if (level <= verbose)						\
+		printk(KERN_DEBUG ABIT_UGURU_NAME ": "	format , ## arg)
+/* Macros to help calculate the sysfs_names array length */
+/* sum of strlen of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0,
+   in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0 */
+#define ABITUGURU_IN_NAMES_LENGTH	(11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14)
+/* sum of strlen of: temp??_input\0, temp??_max\0, temp??_crit\0,
+   temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0 */
+#define ABITUGURU_TEMP_NAMES_LENGTH	(13 + 11 + 12 + 13 + 20 + 12 + 16)
+/* sum of strlen of: fan?_input\0, fan?_min\0, fan?_alarm\0,
+   fan?_alarm_enable\0, fan?_beep\0, fan?_shutdown\0 */
+#define ABITUGURU_FAN_NAMES_LENGTH	(11 + 9 + 11 + 18 + 10 + 14)
+/* sum of strlen of: pwm?_enable\0, pwm?_auto_channels_temp\0,
+   pwm?_auto_point{1,2}_pwm\0, pwm?_auto_point{1,2}_temp\0 */
+#define ABITUGURU_PWM_NAMES_LENGTH	(12 + 24 + 2 * 21 + 2 * 22)
+/* IN_NAMES_LENGTH > TEMP_NAMES_LENGTH so assume all bank1 sensors are in */
+#define ABITUGURU_SYSFS_NAMES_LENGTH	( \
+	ABIT_UGURU_MAX_BANK1_SENSORS * ABITUGURU_IN_NAMES_LENGTH + \
+	ABIT_UGURU_MAX_BANK2_SENSORS * ABITUGURU_FAN_NAMES_LENGTH + \
+	ABIT_UGURU_MAX_PWMS * ABITUGURU_PWM_NAMES_LENGTH)
+
+/* All the macros below are named identical to the oguru and oguru2 programs
+   reverse engineered by Olle Sandberg, hence the names might not be 100%
+   logical. I could come up with better names, but I prefer keeping the names
+   identical so that this driver can be compared with his work more easily. */
+/* Two i/o-ports are used by uGuru */
+#define ABIT_UGURU_BASE				0x00E0
+/* Used to tell uGuru what to read and to read the actual data */
+#define ABIT_UGURU_CMD				0x00
+/* Mostly used to check if uGuru is busy */
+#define ABIT_UGURU_DATA				0x04
+#define ABIT_UGURU_REGION_LENGTH		5
+/* uGuru status' */
+#define ABIT_UGURU_STATUS_WRITE			0x00 /* Ready to be written */
+#define ABIT_UGURU_STATUS_READ			0x01 /* Ready to be read */
+#define ABIT_UGURU_STATUS_INPUT			0x08 /* More input */
+#define ABIT_UGURU_STATUS_READY			0x09 /* Ready to be written */
+
+/* Constants */
+/* in (Volt) sensors go up to 3494 mV, temp to 255000 millidegrees Celsius */
+static const int abituguru_bank1_max_value[2] = { 3494, 255000 };
+/* Min / Max allowed values for sensor2 (fan) alarm threshold, these values
+   correspond to 300-3000 RPM */
+static const u8 abituguru_bank2_min_threshold = 5;
+static const u8 abituguru_bank2_max_threshold = 50;
+/* Register 0 is a bitfield, 1 and 2 are pwm settings (255 = 100%), 3 and 4
+   are temperature trip points. */
+static const int abituguru_pwm_settings_multiplier[5] = { 0, 1, 1, 1000, 1000 };
+/* Min / Max allowed values for pwm_settings. Note: pwm1 (CPU fan) is a
+   special case the minium allowed pwm% setting for this is 30% (77) on
+   some MB's this special case is handled in the code! */
+static const u8 abituguru_pwm_min[5] = { 0, 170, 170, 25, 25 };
+static const u8 abituguru_pwm_max[5] = { 0, 255, 255, 75, 75 };
+
+
+/* Insmod parameters */
+static int force;
+module_param(force, bool, 0);
+MODULE_PARM_DESC(force, "Set to one to force detection.");
+static int fan_sensors;
+module_param(fan_sensors, int, 0);
+MODULE_PARM_DESC(fan_sensors, "Number of fan sensors on the uGuru "
+	"(0 = autodetect)");
+static int pwms;
+module_param(pwms, int, 0);
+MODULE_PARM_DESC(pwms, "Number of PWMs on the uGuru "
+	"(0 = autodetect)");
+
+/* Default verbose is 2, since this driver is still in the testing phase */
+static int verbose = 2;
+module_param(verbose, int, 0644);
+MODULE_PARM_DESC(verbose, "How verbose should the driver be? (0-3):\n"
+	"   0 normal output\n"
+	"   1 + verbose error reporting\n"
+	"   2 + sensors type probing info\n"
+	"   3 + retryable error reporting");
+
+
+/* For the Abit uGuru, we need to keep some data in memory.
+   The structure is dynamically allocated, at the same time when a new
+   abituguru device is allocated. */
+struct abituguru_data {
+	struct class_device *class_dev; /* hwmon registered device */
+	struct mutex update_lock;	/* protect access to data and uGuru */
+	unsigned long last_updated;	/* In jiffies */
+	unsigned short addr;		/* uguru base address */
+	char uguru_ready;		/* is the uguru in ready state? */
+	unsigned char update_timeouts;	/* number of update timeouts since last
+					   successful update */
+
+	/* The sysfs attr and their names are generated automatically, for bank1
+	   we cannot use a predefined array because we don't know beforehand
+	   of a sensor is a volt or a temp sensor, for bank2 and the pwms its
+	   easier todo things the same way.  For in sensors we have 9 (temp 7)
+	   sysfs entries per sensor, for bank2 and pwms 6. */
+	struct sensor_device_attribute_2 sysfs_attr[
+		ABIT_UGURU_MAX_BANK1_SENSORS * 9 +
+		ABIT_UGURU_MAX_BANK2_SENSORS * 6 + ABIT_UGURU_MAX_PWMS * 6];
+	/* Buffer to store the dynamically generated sysfs names */
+	char sysfs_names[ABITUGURU_SYSFS_NAMES_LENGTH];
+
+	/* Bank 1 data */
+	/* number of and addresses of [0] in, [1] temp sensors */
+	u8 bank1_sensors[2];
+	u8 bank1_address[2][ABIT_UGURU_MAX_BANK1_SENSORS];
+	u8 bank1_value[ABIT_UGURU_MAX_BANK1_SENSORS];
+	/* This array holds 3 entries per sensor for the bank 1 sensor settings
+	   (flags, min, max for voltage / flags, warn, shutdown for temp). */
+	u8 bank1_settings[ABIT_UGURU_MAX_BANK1_SENSORS][3];
+	/* Maximum value for each sensor used for scaling in mV/millidegrees
+	   Celsius. */
+	int bank1_max_value[ABIT_UGURU_MAX_BANK1_SENSORS];
+
+	/* Bank 2 data, ABIT_UGURU_MAX_BANK2_SENSORS entries for bank2 */
+	u8 bank2_sensors; /* actual number of bank2 sensors found */
+	u8 bank2_value[ABIT_UGURU_MAX_BANK2_SENSORS];
+	u8 bank2_settings[ABIT_UGURU_MAX_BANK2_SENSORS][2]; /* flags, min */
+
+	/* Alarms 2 bytes for bank1, 1 byte for bank2 */
+	u8 alarms[3];
+
+	/* Fan PWM (speed control) 5 bytes per PWM */
+	u8 pwms; /* actual number of pwms found */
+	u8 pwm_settings[ABIT_UGURU_MAX_PWMS][5];
+};
+
+/* wait till the uguru is in the specified state */
+static int abituguru_wait(struct abituguru_data *data, u8 state)
+{
+	int timeout = ABIT_UGURU_WAIT_TIMEOUT;
+
+	while (inb_p(data->addr + ABIT_UGURU_DATA) != state) {
+		timeout--;
+		if (timeout == 0)
+			return -EBUSY;
+	}
+	return 0;
+}
+
+/* Put the uguru in ready for input state */
+static int abituguru_ready(struct abituguru_data *data)
+{
+	int timeout = ABIT_UGURU_READY_TIMEOUT;
+
+	if (data->uguru_ready)
+		return 0;
+
+	/* Reset? / Prepare for next read/write cycle */
+	outb(0x00, data->addr + ABIT_UGURU_DATA);
+
+	/* Wait till the uguru is ready */
+	if (abituguru_wait(data, ABIT_UGURU_STATUS_READY)) {
+		ABIT_UGURU_DEBUG(1,
+			"timeout exceeded waiting for ready state\n");
+		return -EIO;
+	}
+
+	/* Cmd port MUST be read now and should contain 0xAC */
+	while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
+		timeout--;
+		if (timeout == 0) {
+			ABIT_UGURU_DEBUG(1,
+			   "CMD reg does not hold 0xAC after ready command\n");
+			return -EIO;
+		}
+	}
+
+	/* After this the ABIT_UGURU_DATA port should contain
+	   ABIT_UGURU_STATUS_INPUT */
+	timeout = ABIT_UGURU_READY_TIMEOUT;
+	while (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT) {
+		timeout--;
+		if (timeout == 0) {
+			ABIT_UGURU_DEBUG(1,
+				"state != more input after ready command\n");
+			return -EIO;
+		}
+	}
+
+	data->uguru_ready = 1;
+	return 0;
+}
+
+/* Send the bank and then sensor address to the uGuru for the next read/write
+   cycle. This function gets called as the first part of a read/write by
+   abituguru_read and abituguru_write. This function should never be
+   called by any other function. */
+static int abituguru_send_address(struct abituguru_data *data,
+	u8 bank_addr, u8 sensor_addr, int retries)
+{
+	/* assume the caller does error handling itself if it has not requested
+	   any retries, and thus be quiet. */
+	int report_errors = retries;
+
+	for (;;) {
+		/* Make sure the uguru is ready and then send the bank address,
+		   after this the uguru is no longer "ready". */
+		if (abituguru_ready(data) != 0)
+			return -EIO;
+		outb(bank_addr, data->addr + ABIT_UGURU_DATA);
+		data->uguru_ready = 0;
+
+		/* Wait till the uguru is ABIT_UGURU_STATUS_INPUT state again
+		   and send the sensor addr */
+		if (abituguru_wait(data, ABIT_UGURU_STATUS_INPUT)) {
+			if (retries) {
+				ABIT_UGURU_DEBUG(3, "timeout exceeded "
+					"waiting for more input state, %d "
+					"tries remaining\n", retries);
+				set_current_state(TASK_UNINTERRUPTIBLE);
+				schedule_timeout(ABIT_UGURU_RETRY_DELAY);
+				retries--;
+				continue;
+			}
+			if (report_errors)
+				ABIT_UGURU_DEBUG(1, "timeout exceeded "
+					"waiting for more input state "
+					"(bank: %d)\n", (int)bank_addr);
+			return -EBUSY;
+		}
+		outb(sensor_addr, data->addr + ABIT_UGURU_CMD);
+		return 0;
+	}
+}
+
+/* Read count bytes from sensor sensor_addr in bank bank_addr and store the
+   result in buf, retry the send address part of the read retries times. */
+static int abituguru_read(struct abituguru_data *data,
+	u8 bank_addr, u8 sensor_addr, u8 *buf, int count, int retries)
+{
+	int i;
+
+	/* Send the address */
+	i = abituguru_send_address(data, bank_addr, sensor_addr, retries);
+	if (i)
+		return i;
+
+	/* And read the data */
+	for (i = 0; i < count; i++) {
+		if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
+			ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for "
+				"read state (bank: %d, sensor: %d)\n",
+				(int)bank_addr, (int)sensor_addr);
+			break;
+		}
+		buf[i] = inb(data->addr + ABIT_UGURU_CMD);
+	}
+
+	/* Last put the chip back in ready state */
+	abituguru_ready(data);
+
+	return i;
+}
+
+/* Write count bytes from buf to sensor sensor_addr in bank bank_addr, the send
+   address part of the write is always retried ABIT_UGURU_MAX_RETRIES times. */
+static int abituguru_write(struct abituguru_data *data,
+	u8 bank_addr, u8 sensor_addr, u8 *buf, int count)
+{
+	int i;
+
+	/* Send the address */
+	i = abituguru_send_address(data, bank_addr, sensor_addr,
+		ABIT_UGURU_MAX_RETRIES);
+	if (i)
+		return i;
+
+	/* And write the data */
+	for (i = 0; i < count; i++) {
+		if (abituguru_wait(data, ABIT_UGURU_STATUS_WRITE)) {
+			ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for "
+				"write state (bank: %d, sensor: %d)\n",
+				(int)bank_addr, (int)sensor_addr);
+			break;
+		}
+		outb(buf[i], data->addr + ABIT_UGURU_CMD);
+	}
+
+	/* Now we need to wait till the chip is ready to be read again,
+	   don't ask why */
+	if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
+		ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for read state "
+			"after write (bank: %d, sensor: %d)\n", (int)bank_addr,
+			(int)sensor_addr);
+		return -EIO;
+	}
+
+	/* Cmd port MUST be read now and should contain 0xAC */
+	if (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
+		ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after write "
+			"(bank: %d, sensor: %d)\n", (int)bank_addr,
+			(int)sensor_addr);
+		return -EIO;
+	}
+
+	/* Last put the chip back in ready state */
+	abituguru_ready(data);
+
+	return i;
+}
+
+/* Detect sensor type. Temp and Volt sensors are enabled with
+   different masks and will ignore enable masks not meant for them.
+   This enables us to test what kind of sensor we're dealing with.
+   By setting the alarm thresholds so that we will always get an
+   alarm for sensor type X and then enabling the sensor as sensor type
+   X, if we then get an alarm it is a sensor of type X. */
+static int __devinit
+abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
+				   u8 sensor_addr)
+{
+	u8 val, buf[3];
+	int ret = ABIT_UGURU_NC;
+
+	/* First read the sensor and the current settings */
+	if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, sensor_addr, &val,
+			1, ABIT_UGURU_MAX_RETRIES) != 1)
+		return -ENODEV;
+
+	/* Test val is sane / usable for sensor type detection. */
+	if ((val < 10u) || (val > 240u)) {
+		printk(KERN_WARNING ABIT_UGURU_NAME
+			": bank1-sensor: %d reading (%d) too close to limits, "
+			"unable to determine sensor type, skipping sensor\n",
+			(int)sensor_addr, (int)val);
+		/* assume no sensor is there for sensors for which we can't
+		   determine the sensor type because their reading is too close
+		   to their limits, this usually means no sensor is there. */
+		return ABIT_UGURU_NC;
+	}
+
+	ABIT_UGURU_DEBUG(2, "testing bank1 sensor %d\n", (int)sensor_addr);
+	/* Volt sensor test, enable volt low alarm, set min value ridicously
+	   high. If its a volt sensor this should always give us an alarm. */
+	buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
+	buf[1] = 245;
+	buf[2] = 250;
+	if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
+			buf, 3) != 3)
+		return -ENODEV;
+	/* Now we need 20 ms to give the uguru time to read the sensors
+	   and raise a voltage alarm */
+	set_current_state(TASK_UNINTERRUPTIBLE);
+	schedule_timeout(HZ/50);
+	/* Check for alarm and check the alarm is a volt low alarm. */
+	if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
+			ABIT_UGURU_MAX_RETRIES) != 3)
+		return -ENODEV;
+	if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
+				sensor_addr, buf, 3,
+				ABIT_UGURU_MAX_RETRIES) != 3)
+			return -ENODEV;
+		if (buf[0] & ABIT_UGURU_VOLT_LOW_ALARM_FLAG) {
+			/* Restore original settings */
+			if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
+					sensor_addr,
+					data->bank1_settings[sensor_addr],
+					3) != 3)
+				return -ENODEV;
+			ABIT_UGURU_DEBUG(2, "  found volt sensor\n");
+			return ABIT_UGURU_IN_SENSOR;
+		} else
+			ABIT_UGURU_DEBUG(2, "  alarm raised during volt "
+				"sensor test, but volt low flag not set\n");
+	} else
+		ABIT_UGURU_DEBUG(2, "  alarm not raised during volt sensor "
+			"test\n");
+
+	/* Temp sensor test, enable sensor as a temp sensor, set beep value
+	   ridicously low (but not too low, otherwise uguru ignores it).
+	   If its a temp sensor this should always give us an alarm. */
+	buf[0] = ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE;
+	buf[1] = 5;
+	buf[2] = 10;
+	if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
+			buf, 3) != 3)
+		return -ENODEV;
+	/* Now we need 50 ms to give the uguru time to read the sensors
+	   and raise a temp alarm */
+	set_current_state(TASK_UNINTERRUPTIBLE);
+	schedule_timeout(HZ/20);
+	/* Check for alarm and check the alarm is a temp high alarm. */
+	if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
+			ABIT_UGURU_MAX_RETRIES) != 3)
+		return -ENODEV;
+	if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
+				sensor_addr, buf, 3,
+				ABIT_UGURU_MAX_RETRIES) != 3)
+			return -ENODEV;
+		if (buf[0] & ABIT_UGURU_TEMP_HIGH_ALARM_FLAG) {
+			ret = ABIT_UGURU_TEMP_SENSOR;
+			ABIT_UGURU_DEBUG(2, "  found temp sensor\n");
+		} else
+			ABIT_UGURU_DEBUG(2, "  alarm raised during temp "
+				"sensor test, but temp high flag not set\n");
+	} else
+		ABIT_UGURU_DEBUG(2, "  alarm not raised during temp sensor "
+			"test\n");
+
+	/* Restore original settings */
+	if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
+			data->bank1_settings[sensor_addr], 3) != 3)
+		return -ENODEV;
+
+	return ret;
+}
+
+/* These functions try to find out how many sensors there are in bank2 and how
+   many pwms there are. The purpose of this is to make sure that we don't give
+   the user the possibility to change settings for non-existent sensors / pwm.
+   The uGuru will happily read / write whatever memory happens to be after the
+   memory storing the PWM settings when reading/writing to a PWM which is not
+   there. Notice even if we detect a PWM which doesn't exist we normally won't
+   write to it, unless the user tries to change the settings.
+
+   Although the uGuru allows reading (settings) from non existing bank2
+   sensors, my version of the uGuru does seem to stop writing to them, the
+   write function above aborts in this case with:
+   "CMD reg does not hold 0xAC after write"
+
+   Notice these 2 tests are non destructive iow read-only tests, otherwise
+   they would defeat their purpose. Although for the bank2_sensors detection a
+   read/write test would be feasible because of the reaction above, I've
+   however opted to stay on the safe side. */
+static void __devinit
+abituguru_detect_no_bank2_sensors(struct abituguru_data *data)
+{
+	int i;
+
+	if (fan_sensors) {
+		data->bank2_sensors = fan_sensors;
+		ABIT_UGURU_DEBUG(2, "assuming %d fan sensors because of "
+			"\"fan_sensors\" module param\n",
+			(int)data->bank2_sensors);
+		return;
+	}
+
+	ABIT_UGURU_DEBUG(2, "detecting number of fan sensors\n");
+	for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
+		/* 0x89 are the known used bits:
+		   -0x80 enable shutdown
+		   -0x08 enable beep
+		   -0x01 enable alarm
+		   All other bits should be 0, but on some motherboards
+		   0x40 (bit 6) is also high for some of the fans?? */
+		if (data->bank2_settings[i][0] & ~0xC9) {
+			ABIT_UGURU_DEBUG(2, "  bank2 sensor %d does not seem "
+				"to be a fan sensor: settings[0] = %02X\n",
+				i, (unsigned int)data->bank2_settings[i][0]);
+			break;
+		}
+
+		/* check if the threshold is within the allowed range */
+		if (data->bank2_settings[i][1] <
+				abituguru_bank2_min_threshold) {
+			ABIT_UGURU_DEBUG(2, "  bank2 sensor %d does not seem "
+				"to be a fan sensor: the threshold (%d) is "
+				"below the minimum (%d)\n", i,
+				(int)data->bank2_settings[i][1],
+				(int)abituguru_bank2_min_threshold);
+			break;
+		}
+		if (data->bank2_settings[i][1] >
+				abituguru_bank2_max_threshold) {
+			ABIT_UGURU_DEBUG(2, "  bank2 sensor %d does not seem "
+				"to be a fan sensor: the threshold (%d) is "
+				"above the maximum (%d)\n", i,
+				(int)data->bank2_settings[i][1],
+				(int)abituguru_bank2_max_threshold);
+			break;
+		}
+	}
+
+	data->bank2_sensors = i;
+	ABIT_UGURU_DEBUG(2, " found: %d fan sensors\n",
+		(int)data->bank2_sensors);
+}
+
+static void __devinit
+abituguru_detect_no_pwms(struct abituguru_data *data)
+{
+	int i, j;
+
+	if (pwms) {
+		data->pwms = pwms;
+		ABIT_UGURU_DEBUG(2, "assuming %d PWM outputs because of "
+			"\"pwms\" module param\n", (int)data->pwms);
+		return;
+	}
+
+	ABIT_UGURU_DEBUG(2, "detecting number of PWM outputs\n");
+	for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
+		/* 0x80 is the enable bit and the low
+		   nibble is which temp sensor to use,
+		   the other bits should be 0 */
+		if (data->pwm_settings[i][0] & ~0x8F) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: settings[0] = %02X\n",
+				i, (unsigned int)data->pwm_settings[i][0]);
+			break;
+		}
+
+		/* the low nibble must correspond to one of the temp sensors
+		   we've found */
+		for (j = 0; j < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR];
+				j++) {
+			if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][j] ==
+					(data->pwm_settings[i][0] & 0x0F))
+				break;
+		}
+		if (j == data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: %d is not a valid temp "
+				"sensor address\n", i,
+				data->pwm_settings[i][0] & 0x0F);
+			break;
+		}
+
+		/* check if all other settings are within the allowed range */
+		for (j = 1; j < 5; j++) {
+			u8 min;
+			/* special case pwm1 min pwm% */
+			if ((i == 0) && ((j == 1) || (j == 2)))
+				min = 77;
+			else
+				min = abituguru_pwm_min[j];
+			if (data->pwm_settings[i][j] < min) {
+				ABIT_UGURU_DEBUG(2, "  pwm channel %d does "
+					"not seem to be a pwm channel: "
+					"setting %d (%d) is below the minimum "
+					"value (%d)\n", i, j,
+					(int)data->pwm_settings[i][j],
+					(int)min);
+				goto abituguru_detect_no_pwms_exit;
+			}
+			if (data->pwm_settings[i][j] > abituguru_pwm_max[j]) {
+				ABIT_UGURU_DEBUG(2, "  pwm channel %d does "
+					"not seem to be a pwm channel: "
+					"setting %d (%d) is above the maximum "
+					"value (%d)\n", i, j,
+					(int)data->pwm_settings[i][j],
+					(int)abituguru_pwm_max[j]);
+				goto abituguru_detect_no_pwms_exit;
+			}
+		}
+
+		/* check that min temp < max temp and min pwm < max pwm */
+		if (data->pwm_settings[i][1] >= data->pwm_settings[i][2]) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: min pwm (%d) >= "
+				"max pwm (%d)\n", i,
+				(int)data->pwm_settings[i][1],
+				(int)data->pwm_settings[i][2]);
+			break;
+		}
+		if (data->pwm_settings[i][3] >= data->pwm_settings[i][4]) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: min temp (%d) >= "
+				"max temp (%d)\n", i,
+				(int)data->pwm_settings[i][3],
+				(int)data->pwm_settings[i][4]);
+			break;
+		}
+	}
+
+abituguru_detect_no_pwms_exit:
+	data->pwms = i;
+	ABIT_UGURU_DEBUG(2, " found: %d PWM outputs\n", (int)data->pwms);
+}
+
+/* Following are the sysfs callback functions. These functions expect:
+   sensor_device_attribute_2->index:   sensor address/offset in the bank
+   sensor_device_attribute_2->nr:      register offset, bitmask or NA. */
+static struct abituguru_data *abituguru_update_device(struct device *dev);
+
+static ssize_t show_bank1_value(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	return sprintf(buf, "%d\n", (data->bank1_value[attr->index] *
+		data->bank1_max_value[attr->index] + 128) / 255);
+}
+
+static ssize_t show_bank1_setting(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%d\n",
+		(data->bank1_settings[attr->index][attr->nr] *
+		data->bank1_max_value[attr->index] + 128) / 255);
+}
+
+static ssize_t show_bank2_value(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	return sprintf(buf, "%d\n", (data->bank2_value[attr->index] *
+		ABIT_UGURU_FAN_MAX + 128) / 255);
+}
+
+static ssize_t show_bank2_setting(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%d\n",
+		(data->bank2_settings[attr->index][attr->nr] *
+		ABIT_UGURU_FAN_MAX + 128) / 255);
+}
+
+static ssize_t store_bank1_setting(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 val = (simple_strtoul(buf, NULL, 10) * 255 +
+		data->bank1_max_value[attr->index]/2) /
+		data->bank1_max_value[attr->index];
+	ssize_t ret = count;
+
+	mutex_lock(&data->update_lock);
+	if (data->bank1_settings[attr->index][attr->nr] != val) {
+		u8 orig_val = data->bank1_settings[attr->index][attr->nr];
+		data->bank1_settings[attr->index][attr->nr] = val;
+		if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
+				attr->index, data->bank1_settings[attr->index],
+				3) <= attr->nr) {
+			data->bank1_settings[attr->index][attr->nr] = orig_val;
+			ret = -EIO;
+		}
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t store_bank2_setting(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 val = (simple_strtoul(buf, NULL, 10)*255 + ABIT_UGURU_FAN_MAX/2) /
+		ABIT_UGURU_FAN_MAX;
+	ssize_t ret = count;
+
+	/* this check can be done before taking the lock */
+	if ((val < abituguru_bank2_min_threshold) ||
+			(val > abituguru_bank2_max_threshold))
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	if (data->bank2_settings[attr->index][attr->nr] != val) {
+		u8 orig_val = data->bank2_settings[attr->index][attr->nr];
+		data->bank2_settings[attr->index][attr->nr] = val;
+		if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK2 + 2,
+				attr->index, data->bank2_settings[attr->index],
+				2) <= attr->nr) {
+			data->bank2_settings[attr->index][attr->nr] = orig_val;
+			ret = -EIO;
+		}
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_bank1_alarm(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	/* See if the alarm bit for this sensor is set, and if the
+	   alarm matches the type of alarm we're looking for (for volt
+	   it can be either low or high). The type is stored in a few
+	   readonly bits in the settings part of the relevant sensor.
+	   The bitmask of the type is passed to us in attr->nr. */
+	if ((data->alarms[attr->index / 8] & (0x01 << (attr->index % 8))) &&
+			(data->bank1_settings[attr->index][0] & attr->nr))
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_bank2_alarm(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	if (data->alarms[2] & (0x01 << attr->index))
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_bank1_mask(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	if (data->bank1_settings[attr->index][0] & attr->nr)
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_bank2_mask(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	if (data->bank2_settings[attr->index][0] & attr->nr)
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t store_bank1_mask(struct device *dev,
+	struct device_attribute *devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int mask = simple_strtoul(buf, NULL, 10);
+	ssize_t ret = count;
+	u8 orig_val;
+
+	mutex_lock(&data->update_lock);
+	orig_val = data->bank1_settings[attr->index][0];
+
+	if (mask)
+		data->bank1_settings[attr->index][0] |= attr->nr;
+	else
+		data->bank1_settings[attr->index][0] &= ~attr->nr;
+
+	if ((data->bank1_settings[attr->index][0] != orig_val) &&
+			(abituguru_write(data,
+			ABIT_UGURU_SENSOR_BANK1 + 2, attr->index,
+			data->bank1_settings[attr->index], 3) < 1)) {
+		data->bank1_settings[attr->index][0] = orig_val;
+		ret = -EIO;
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t store_bank2_mask(struct device *dev,
+	struct device_attribute *devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int mask = simple_strtoul(buf, NULL, 10);
+	ssize_t ret = count;
+	u8 orig_val;
+
+	mutex_lock(&data->update_lock);
+	orig_val = data->bank2_settings[attr->index][0];
+
+	if (mask)
+		data->bank2_settings[attr->index][0] |= attr->nr;
+	else
+		data->bank2_settings[attr->index][0] &= ~attr->nr;
+
+	if ((data->bank2_settings[attr->index][0] != orig_val) &&
+			(abituguru_write(data,
+			ABIT_UGURU_SENSOR_BANK2 + 2, attr->index,
+			data->bank2_settings[attr->index], 2) < 1)) {
+		data->bank2_settings[attr->index][0] = orig_val;
+		ret = -EIO;
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+/* Fan PWM (speed control) */
+static ssize_t show_pwm_setting(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%d\n", data->pwm_settings[attr->index][attr->nr] *
+		abituguru_pwm_settings_multiplier[attr->nr]);
+}
+
+static ssize_t store_pwm_setting(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 min, val = (simple_strtoul(buf, NULL, 10) +
+		abituguru_pwm_settings_multiplier[attr->nr]/2) /
+		abituguru_pwm_settings_multiplier[attr->nr];
+	ssize_t ret = count;
+
+	/* special case pwm1 min pwm% */
+	if ((attr->index == 0) && ((attr->nr == 1) || (attr->nr == 2)))
+		min = 77;
+	else
+		min = abituguru_pwm_min[attr->nr];
+
+	/* this check can be done before taking the lock */
+	if ((val < min) || (val > abituguru_pwm_max[attr->nr]))
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	/* this check needs to be done after taking the lock */
+	if ((attr->nr & 1) &&
+			(val >= data->pwm_settings[attr->index][attr->nr + 1]))
+		ret = -EINVAL;
+	else if (!(attr->nr & 1) &&
+			(val <= data->pwm_settings[attr->index][attr->nr - 1]))
+		ret = -EINVAL;
+	else if (data->pwm_settings[attr->index][attr->nr] != val) {
+		u8 orig_val = data->pwm_settings[attr->index][attr->nr];
+		data->pwm_settings[attr->index][attr->nr] = val;
+		if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
+				attr->index, data->pwm_settings[attr->index],
+				5) <= attr->nr) {
+			data->pwm_settings[attr->index][attr->nr] =
+				orig_val;
+			ret = -EIO;
+		}
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_pwm_sensor(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int i;
+	/* We need to walk to the temp sensor addresses to find what
+	   the userspace id of the configured temp sensor is. */
+	for (i = 0; i < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]; i++)
+		if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][i] ==
+				(data->pwm_settings[attr->index][0] & 0x0F))
+			return sprintf(buf, "%d\n", i+1);
+
+	return -ENXIO;
+}
+
+static ssize_t store_pwm_sensor(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	unsigned long val = simple_strtoul(buf, NULL, 10) - 1;
+	ssize_t ret = count;
+
+	mutex_lock(&data->update_lock);
+	if (val < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]) {
+		u8 orig_val = data->pwm_settings[attr->index][0];
+		u8 address = data->bank1_address[ABIT_UGURU_TEMP_SENSOR][val];
+		data->pwm_settings[attr->index][0] &= 0xF0;
+		data->pwm_settings[attr->index][0] |= address;
+		if (data->pwm_settings[attr->index][0] != orig_val) {
+			if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
+					attr->index,
+					data->pwm_settings[attr->index],
+					5) < 1) {
+				data->pwm_settings[attr->index][0] = orig_val;
+				ret = -EIO;
+			}
+		}
+	}
+	else
+		ret = -EINVAL;
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_pwm_enable(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int res = 0;
+	if (data->pwm_settings[attr->index][0] & ABIT_UGURU_FAN_PWM_ENABLE)
+		res = 2;
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t store_pwm_enable(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 orig_val, user_val = simple_strtoul(buf, NULL, 10);
+	ssize_t ret = count;
+
+	mutex_lock(&data->update_lock);
+	orig_val = data->pwm_settings[attr->index][0];
+	switch (user_val) {
+		case 0:
+			data->pwm_settings[attr->index][0] &=
+				~ABIT_UGURU_FAN_PWM_ENABLE;
+			break;
+		case 2:
+			data->pwm_settings[attr->index][0] |=
+				ABIT_UGURU_FAN_PWM_ENABLE;
+			break;
+		default:
+			ret = -EINVAL;
+	}
+	if ((data->pwm_settings[attr->index][0] != orig_val) &&
+			(abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
+			attr->index, data->pwm_settings[attr->index],
+			5) < 1)) {
+		data->pwm_settings[attr->index][0] = orig_val;
+		ret = -EIO;
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_name(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	return sprintf(buf, "%s\n", ABIT_UGURU_NAME);
+}
+
+/* Sysfs attr templates, the real entries are generated automatically. */
+static const
+struct sensor_device_attribute_2 abituguru_sysfs_bank1_templ[2][9] = {
+	{
+	SENSOR_ATTR_2(in%d_input, 0444, show_bank1_value, NULL, 0, 0),
+	SENSOR_ATTR_2(in%d_min, 0644, show_bank1_setting,
+		store_bank1_setting, 1, 0),
+	SENSOR_ATTR_2(in%d_min_alarm, 0444, show_bank1_alarm, NULL,
+		ABIT_UGURU_VOLT_LOW_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(in%d_max, 0644, show_bank1_setting,
+		store_bank1_setting, 2, 0),
+	SENSOR_ATTR_2(in%d_max_alarm, 0444, show_bank1_alarm, NULL,
+		ABIT_UGURU_VOLT_HIGH_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(in%d_beep, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_shutdown, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_min_alarm_enable, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_VOLT_LOW_ALARM_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_max_alarm_enable, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE, 0),
+	}, {
+	SENSOR_ATTR_2(temp%d_input, 0444, show_bank1_value, NULL, 0, 0),
+	SENSOR_ATTR_2(temp%d_alarm, 0444, show_bank1_alarm, NULL,
+		ABIT_UGURU_TEMP_HIGH_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(temp%d_max, 0644, show_bank1_setting,
+		store_bank1_setting, 1, 0),
+	SENSOR_ATTR_2(temp%d_crit, 0644, show_bank1_setting,
+		store_bank1_setting, 2, 0),
+	SENSOR_ATTR_2(temp%d_beep, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(temp%d_shutdown, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(temp%d_alarm_enable, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE, 0),
+	}
+};
+
+static const struct sensor_device_attribute_2 abituguru_sysfs_fan_templ[6] = {
+	SENSOR_ATTR_2(fan%d_input, 0444, show_bank2_value, NULL, 0, 0),
+	SENSOR_ATTR_2(fan%d_alarm, 0444, show_bank2_alarm, NULL, 0, 0),
+	SENSOR_ATTR_2(fan%d_min, 0644, show_bank2_setting,
+		store_bank2_setting, 1, 0),
+	SENSOR_ATTR_2(fan%d_beep, 0644, show_bank2_mask,
+		store_bank2_mask, ABIT_UGURU_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(fan%d_shutdown, 0644, show_bank2_mask,
+		store_bank2_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(fan%d_alarm_enable, 0644, show_bank2_mask,
+		store_bank2_mask, ABIT_UGURU_FAN_LOW_ALARM_ENABLE, 0),
+};
+
+static const struct sensor_device_attribute_2 abituguru_sysfs_pwm_templ[6] = {
+	SENSOR_ATTR_2(pwm%d_enable, 0644, show_pwm_enable,
+		store_pwm_enable, 0, 0),
+	SENSOR_ATTR_2(pwm%d_auto_channels_temp, 0644, show_pwm_sensor,
+		store_pwm_sensor, 0, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point1_pwm, 0644, show_pwm_setting,
+		store_pwm_setting, 1, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point2_pwm, 0644, show_pwm_setting,
+		store_pwm_setting, 2, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point1_temp, 0644, show_pwm_setting,
+		store_pwm_setting, 3, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point2_temp, 0644, show_pwm_setting,
+		store_pwm_setting, 4, 0),
+};
+
+static struct sensor_device_attribute_2 abituguru_sysfs_attr[] = {
+	SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0),
+};
+
+static int __devinit abituguru_probe(struct platform_device *pdev)
+{
+	struct abituguru_data *data;
+	int i, j, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV;
+	char *sysfs_filename;
+
+	/* El weirdo probe order, to keep the sysfs order identical to the
+	   BIOS and window-appliction listing order. */
+	const u8 probe_order[ABIT_UGURU_MAX_BANK1_SENSORS] = {
+		0x00, 0x01, 0x03, 0x04, 0x0A, 0x08, 0x0E, 0x02,
+		0x09, 0x06, 0x05, 0x0B, 0x0F, 0x0D, 0x07, 0x0C };
+
+	if (!(data = kzalloc(sizeof(struct abituguru_data), GFP_KERNEL)))
+		return -ENOMEM;
+
+	data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start;
+	mutex_init(&data->update_lock);
+	platform_set_drvdata(pdev, data);
+
+	/* See if the uGuru is ready */
+	if (inb_p(data->addr + ABIT_UGURU_DATA) == ABIT_UGURU_STATUS_INPUT)
+		data->uguru_ready = 1;
+
+	/* Completely read the uGuru this has 2 purposes:
+	   - testread / see if one really is there.
+	   - make an in memory copy of all the uguru settings for future use. */
+	if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
+			data->alarms, 3, ABIT_UGURU_MAX_RETRIES) != 3)
+		goto abituguru_probe_error;
+
+	for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, i,
+				&data->bank1_value[i], 1,
+				ABIT_UGURU_MAX_RETRIES) != 1)
+			goto abituguru_probe_error;
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1+1, i,
+				data->bank1_settings[i], 3,
+				ABIT_UGURU_MAX_RETRIES) != 3)
+			goto abituguru_probe_error;
+	}
+	/* Note: We don't know how many bank2 sensors / pwms there really are,
+	   but in order to "detect" this we need to read the maximum amount
+	   anyways. If we read sensors/pwms not there we'll just read crap
+	   this can't hurt. We need the detection because we don't want
+	   unwanted writes, which will hurt! */
+	for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2, i,
+				&data->bank2_value[i], 1,
+				ABIT_UGURU_MAX_RETRIES) != 1)
+			goto abituguru_probe_error;
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2+1, i,
+				data->bank2_settings[i], 2,
+				ABIT_UGURU_MAX_RETRIES) != 2)
+			goto abituguru_probe_error;
+	}
+	for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
+		if (abituguru_read(data, ABIT_UGURU_FAN_PWM, i,
+				data->pwm_settings[i], 5,
+				ABIT_UGURU_MAX_RETRIES) != 5)
+			goto abituguru_probe_error;
+	}
+	data->last_updated = jiffies;
+
+	/* Detect sensor types and fill the sysfs attr for bank1 */
+	sysfs_attr_i = 0;
+	sysfs_filename = data->sysfs_names;
+	sysfs_names_free = ABITUGURU_SYSFS_NAMES_LENGTH;
+	for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
+		res = abituguru_detect_bank1_sensor_type(data, probe_order[i]);
+		if (res < 0)
+			goto abituguru_probe_error;
+		if (res == ABIT_UGURU_NC)
+			continue;
+
+		/* res 1 (temp) sensors have 7 sysfs entries, 0 (in) 9 */
+		for (j = 0; j < (res ? 7 : 9); j++) {
+			used = snprintf(sysfs_filename, sysfs_names_free,
+				abituguru_sysfs_bank1_templ[res][j].dev_attr.
+				attr.name, data->bank1_sensors[res] + res)
+				+ 1;
+			data->sysfs_attr[sysfs_attr_i] =
+				abituguru_sysfs_bank1_templ[res][j];
+			data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+				sysfs_filename;
+			data->sysfs_attr[sysfs_attr_i].index = probe_order[i];
+			sysfs_filename += used;
+			sysfs_names_free -= used;
+			sysfs_attr_i++;
+		}
+		data->bank1_max_value[probe_order[i]] =
+			abituguru_bank1_max_value[res];
+		data->bank1_address[res][data->bank1_sensors[res]] =
+			probe_order[i];
+		data->bank1_sensors[res]++;
+	}
+	/* Detect number of sensors and fill the sysfs attr for bank2 (fans) */
+	abituguru_detect_no_bank2_sensors(data);
+	for (i = 0; i < data->bank2_sensors; i++) {
+		for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_fan_templ); j++) {
+			used = snprintf(sysfs_filename, sysfs_names_free,
+				abituguru_sysfs_fan_templ[j].dev_attr.attr.name,
+				i + 1) + 1;
+			data->sysfs_attr[sysfs_attr_i] =
+				abituguru_sysfs_fan_templ[j];
+			data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+				sysfs_filename;
+			data->sysfs_attr[sysfs_attr_i].index = i;
+			sysfs_filename += used;
+			sysfs_names_free -= used;
+			sysfs_attr_i++;
+		}
+	}
+	/* Detect number of sensors and fill the sysfs attr for pwms */
+	abituguru_detect_no_pwms(data);
+	for (i = 0; i < data->pwms; i++) {
+		for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_pwm_templ); j++) {
+			used = snprintf(sysfs_filename, sysfs_names_free,
+				abituguru_sysfs_pwm_templ[j].dev_attr.attr.name,
+				i + 1) + 1;
+			data->sysfs_attr[sysfs_attr_i] =
+				abituguru_sysfs_pwm_templ[j];
+			data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+				sysfs_filename;
+			data->sysfs_attr[sysfs_attr_i].index = i;
+			sysfs_filename += used;
+			sysfs_names_free -= used;
+			sysfs_attr_i++;
+		}
+	}
+	/* Fail safe check, this should never happen! */
+	if (sysfs_names_free < 0) {
+		printk(KERN_ERR ABIT_UGURU_NAME ": Fatal error ran out of "
+		       "space for sysfs attr names. This should never "
+		       "happen please report to the abituguru maintainer "
+		       "(see MAINTAINERS)\n");
+		res = -ENAMETOOLONG;
+		goto abituguru_probe_error;
+	}
+	printk(KERN_INFO ABIT_UGURU_NAME ": found Abit uGuru\n");
+
+	/* Register sysfs hooks */
+	data->class_dev = hwmon_device_register(&pdev->dev);
+	if (IS_ERR(data->class_dev)) {
+		res = PTR_ERR(data->class_dev);
+		goto abituguru_probe_error;
+	}
+	for (i = 0; i < sysfs_attr_i; i++)
+		device_create_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+	for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
+		device_create_file(&pdev->dev,
+			&abituguru_sysfs_attr[i].dev_attr);
+
+	return 0;
+
+abituguru_probe_error:
+	kfree(data);
+	return res;
+}
+
+static int __devexit abituguru_remove(struct platform_device *pdev)
+{
+	struct abituguru_data *data = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+	hwmon_device_unregister(data->class_dev);
+	kfree(data);
+
+	return 0;
+}
+
+static struct abituguru_data *abituguru_update_device(struct device *dev)
+{
+	int i, err;
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	/* fake a complete successful read if no update necessary. */
+	char success = 1;
+
+	mutex_lock(&data->update_lock);
+	if (time_after(jiffies, data->last_updated + HZ)) {
+		success = 0;
+		if ((err = abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
+				data->alarms, 3, 0)) != 3)
+			goto LEAVE_UPDATE;
+		for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
+			if ((err = abituguru_read(data,
+					ABIT_UGURU_SENSOR_BANK1, i,
+					&data->bank1_value[i], 1, 0)) != 1)
+				goto LEAVE_UPDATE;
+			if ((err = abituguru_read(data,
+					ABIT_UGURU_SENSOR_BANK1 + 1, i,
+					data->bank1_settings[i], 3, 0)) != 3)
+				goto LEAVE_UPDATE;
+		}
+		for (i = 0; i < data->bank2_sensors; i++)
+			if ((err = abituguru_read(data,
+					ABIT_UGURU_SENSOR_BANK2, i,
+					&data->bank2_value[i], 1, 0)) != 1)
+				goto LEAVE_UPDATE;
+		/* success! */
+		success = 1;
+		data->update_timeouts = 0;
+LEAVE_UPDATE:
+		/* handle timeout condition */
+		if (err == -EBUSY) {
+			/* No overflow please */
+			if (data->update_timeouts < 255u)
+				data->update_timeouts++;
+			if (data->update_timeouts <= ABIT_UGURU_MAX_TIMEOUTS) {
+				ABIT_UGURU_DEBUG(3, "timeout exceeded, will "
+					"try again next update\n");
+				/* Just a timeout, fake a successful read */
+				success = 1;
+			} else
+				ABIT_UGURU_DEBUG(1, "timeout exceeded %d "
+					"times waiting for more input state\n",
+					(int)data->update_timeouts);
+		}
+		/* On success set last_updated */
+		if (success)
+			data->last_updated = jiffies;
+	}
+	mutex_unlock(&data->update_lock);
+
+	if (success)
+		return data;
+	else
+		return NULL;
+}
+
+static struct platform_driver abituguru_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= ABIT_UGURU_NAME,
+	},
+	.probe	= abituguru_probe,
+	.remove	= __devexit_p(abituguru_remove),
+};
+
+static int __init abituguru_detect(void)
+{
+	/* See if there is an uguru there. After a reboot uGuru will hold 0x00
+	   at DATA and 0xAC, when this driver has already been loaded once
+	   DATA will hold 0x08. For most uGuru's CMD will hold 0xAC in either
+	   scenario but some will hold 0x00.
+	   Some uGuru's initally hold 0x09 at DATA and will only hold 0x08
+	   after reading CMD first, so CMD must be read first! */
+	u8 cmd_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_CMD);
+	u8 data_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_DATA);
+	if (((data_val == 0x00) || (data_val == 0x08)) &&
+	    ((cmd_val == 0x00) || (cmd_val == 0xAC)))
+		return ABIT_UGURU_BASE;
+
+	ABIT_UGURU_DEBUG(2, "no Abit uGuru found, data = 0x%02X, cmd = "
+		"0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
+
+	if (force) {
+		printk(KERN_INFO ABIT_UGURU_NAME ": Assuming Abit uGuru is "
+				"present because of \"force\" parameter\n");
+		return ABIT_UGURU_BASE;
+	}
+
+	/* No uGuru found */
+	return -ENODEV;
+}
+
+static struct platform_device *abituguru_pdev;
+
+static int __init abituguru_init(void)
+{
+	int address, err;
+	struct resource res = { .flags = IORESOURCE_IO };
+
+	address = abituguru_detect();
+	if (address < 0)
+		return address;
+
+	err = platform_driver_register(&abituguru_driver);
+	if (err)
+		goto exit;
+
+	abituguru_pdev = platform_device_alloc(ABIT_UGURU_NAME, address);
+	if (!abituguru_pdev) {
+		printk(KERN_ERR ABIT_UGURU_NAME
+			": Device allocation failed\n");
+		err = -ENOMEM;
+		goto exit_driver_unregister;
+	}
+
+	res.start = address;
+	res.end = address + ABIT_UGURU_REGION_LENGTH - 1;
+	res.name = ABIT_UGURU_NAME;
+
+	err = platform_device_add_resources(abituguru_pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR ABIT_UGURU_NAME
+			": Device resource addition failed (%d)\n", err);
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(abituguru_pdev);
+	if (err) {
+		printk(KERN_ERR ABIT_UGURU_NAME
+			": Device addition failed (%d)\n", err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(abituguru_pdev);
+exit_driver_unregister:
+	platform_driver_unregister(&abituguru_driver);
+exit:
+	return err;
+}
+
+static void __exit abituguru_exit(void)
+{
+	platform_device_unregister(abituguru_pdev);
+	platform_driver_unregister(&abituguru_driver);
+}
+
+MODULE_AUTHOR("Hans de Goede <j.w.r.degoede@hhs.nl>");
+MODULE_DESCRIPTION("Abit uGuru Sensor device");
+MODULE_LICENSE("GPL");
+
+module_init(abituguru_init);
+module_exit(abituguru_exit);
diff --git a/drivers/hwmon/f71805f.c b/drivers/hwmon/f71805f.c
index 885465df6e6..fd72440faf7 100644
--- a/drivers/hwmon/f71805f.c
+++ b/drivers/hwmon/f71805f.c
@@ -99,10 +99,6 @@ superio_exit(int base)
 #define ADDR_REG_OFFSET		0
 #define DATA_REG_OFFSET		1
 
-static struct resource f71805f_resource __initdata = {
-	.flags	= IORESOURCE_IO,
-};
-
 /*
  * Registers
  */
@@ -782,6 +778,11 @@ static struct platform_driver f71805f_driver = {
 
 static int __init f71805f_device_add(unsigned short address)
 {
+	struct resource res = {
+		.start	= address,
+		.end	= address + REGION_LENGTH - 1,
+		.flags	= IORESOURCE_IO,
+	};
 	int err;
 
 	pdev = platform_device_alloc(DRVNAME, address);
@@ -791,10 +792,8 @@ static int __init f71805f_device_add(unsigned short address)
 		goto exit;
 	}
 
-	f71805f_resource.start = address;
-	f71805f_resource.end = address + REGION_LENGTH - 1;
-	f71805f_resource.name = pdev->name;
-	err = platform_device_add_resources(pdev, &f71805f_resource, 1);
+	res.name = pdev->name;
+	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
 		printk(KERN_ERR DRVNAME ": Device resource addition failed "
 		       "(%d)\n", err);
diff --git a/drivers/hwmon/hdaps.c b/drivers/hwmon/hdaps.c
index 1659f6c4145..42b632889dd 100644
--- a/drivers/hwmon/hdaps.c
+++ b/drivers/hwmon/hdaps.c
@@ -41,7 +41,7 @@
 #define HDAPS_PORT_STATE	0x1611	/* device state */
 #define HDAPS_PORT_YPOS		0x1612	/* y-axis position */
 #define	HDAPS_PORT_XPOS		0x1614	/* x-axis position */
-#define HDAPS_PORT_TEMP1	0x1616	/* device temperature, in celcius */
+#define HDAPS_PORT_TEMP1	0x1616	/* device temperature, in Celsius */
 #define HDAPS_PORT_YVAR		0x1617	/* y-axis variance (what is this?) */
 #define HDAPS_PORT_XVAR		0x1619	/* x-axis variance (what is this?) */
 #define HDAPS_PORT_TEMP2	0x161b	/* device temperature (again?) */
@@ -522,13 +522,15 @@ static int __init hdaps_init(void)
 {
 	int ret;
 
-	/* Note that DMI_MATCH(...,"ThinkPad T42") will match "ThinkPad T42p" */
+	/* Note that HDAPS_DMI_MATCH_NORMAL("ThinkPad T42") would match
+	  "ThinkPad T42p", so the order of the entries matters */
 	struct dmi_system_id hdaps_whitelist[] = {
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad H"),
 		HDAPS_DMI_MATCH_INVERT("ThinkPad R50p"),
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad R50"),
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad R51"),
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad R52"),
+		HDAPS_DMI_MATCH_NORMAL("ThinkPad H"),	 /* R52 (1846AQG) */
 		HDAPS_DMI_MATCH_INVERT("ThinkPad T41p"),
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad T41"),
 		HDAPS_DMI_MATCH_INVERT("ThinkPad T42p"),
@@ -536,9 +538,9 @@ static int __init hdaps_init(void)
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad T43"),
 		HDAPS_DMI_MATCH_LENOVO("ThinkPad T60p"),
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad X40"),
-		HDAPS_DMI_MATCH_NORMAL("ThinkPad X41 Tablet"),
 		HDAPS_DMI_MATCH_NORMAL("ThinkPad X41"),
 		HDAPS_DMI_MATCH_LENOVO("ThinkPad X60"),
+		HDAPS_DMI_MATCH_NORMAL("ThinkPad Z60m"),
 		{ .ident = NULL }
 	};
 
diff --git a/drivers/hwmon/hwmon-vid.c b/drivers/hwmon/hwmon-vid.c
index a74a44f16f5..a6764ff0080 100644
--- a/drivers/hwmon/hwmon-vid.c
+++ b/drivers/hwmon/hwmon-vid.c
@@ -58,11 +58,20 @@
     doesn't seem to be any named specification for these. The conversion
     tables are detailed directly in the various Pentium M datasheets:
     http://www.intel.com/design/intarch/pentiumm/docs_pentiumm.htm
+
+    The 14 specification corresponds to Intel Core series. There
+    doesn't seem to be any named specification for these. The conversion
+    tables are detailed directly in the various Pentium Core datasheets:
+    http://www.intel.com/design/mobile/datashts/309221.htm
+
+    The 110 (VRM 11) specification corresponds to Intel Conroe based series.
+    http://www.intel.com/design/processor/applnots/313214.htm
 */
 
 /* vrm is the VRM/VRD document version multiplied by 10.
-   val is the 4-, 5- or 6-bit VID code.
-   Returned value is in mV to avoid floating point in the kernel. */
+   val is the 4-bit or more VID code.
+   Returned value is in mV to avoid floating point in the kernel.
+   Some VID have some bits in uV scale, this is rounded to mV */
 int vid_from_reg(int val, u8 vrm)
 {
 	int vid;
@@ -70,26 +79,36 @@ int vid_from_reg(int val, u8 vrm)
 	switch(vrm) {
 
 	case 100:               /* VRD 10.0 */
+		/* compute in uV, round to mV */
+		val &= 0x3f;
 		if((val & 0x1f) == 0x1f)
 			return 0;
 		if((val & 0x1f) <= 0x09 || val == 0x0a)
-			vid = 10875 - (val & 0x1f) * 250;
+			vid = 1087500 - (val & 0x1f) * 25000;
 		else
-			vid = 18625 - (val & 0x1f) * 250;
+			vid = 1862500 - (val & 0x1f) * 25000;
 		if(val & 0x20)
-			vid -= 125;
-		vid /= 10;      /* only return 3 dec. places for now */
-		return vid;
+			vid -= 12500;
+		return((vid + 500) / 1000);
 
+	case 110:		/* Intel Conroe */
+				/* compute in uV, round to mV */
+		val &= 0xff;
+		if(((val & 0x7e) == 0xfe) || (!(val & 0x7e)))
+			return 0;
+		return((1600000 - (val - 2) * 6250 + 500) / 1000);
 	case 24:                /* Opteron processor */
+		val &= 0x1f;
 		return(val == 0x1f ? 0 : 1550 - val * 25);
 
 	case 91:		/* VRM 9.1 */
 	case 90:		/* VRM 9.0 */
+		val &= 0x1f;
 		return(val == 0x1f ? 0 :
 		                       1850 - val * 25);
 
 	case 85:		/* VRM 8.5 */
+		val &= 0x1f;
 		return((val & 0x10  ? 25 : 0) +
 		       ((val & 0x0f) > 0x04 ? 2050 : 1250) -
 		       ((val & 0x0f) * 50));
@@ -98,14 +117,21 @@ int vid_from_reg(int val, u8 vrm)
 		val &= 0x0f;
 				/* fall through */
 	case 82:		/* VRM 8.2 */
+		val &= 0x1f;
 		return(val == 0x1f ? 0 :
 		       val & 0x10  ? 5100 - (val) * 100 :
 		                     2050 - (val) * 50);
 	case 17:		/* Intel IMVP-II */
+		val &= 0x1f;
 		return(val & 0x10 ? 975 - (val & 0xF) * 25 :
 				    1750 - val * 50);
 	case 13:
-		return(1708 - (val & 0x3f) * 16);
+		val &= 0x3f;
+		return(1708 - val * 16);
+	case 14:		/* Intel Core */
+				/* compute in uV, round to mV */
+		val &= 0x7f;
+		return(val > 0x77 ? 0 : (1500000 - (val * 12500) + 500) / 1000);
 	default:		/* report 0 for unknown */
 		printk(KERN_INFO "hwmon-vid: requested unknown VRM version\n");
 		return 0;
@@ -138,6 +164,8 @@ static struct vrm_model vrm_models[] = {
 	{X86_VENDOR_INTEL, 0x6, 0x9, ANY, 13},		/* Pentium M (130 nm) */
 	{X86_VENDOR_INTEL, 0x6, 0xB, ANY, 85},		/* Tualatin */
 	{X86_VENDOR_INTEL, 0x6, 0xD, ANY, 13},		/* Pentium M (90 nm) */
+	{X86_VENDOR_INTEL, 0x6, 0xE, ANY, 14},		/* Intel Core (65 nm) */
+	{X86_VENDOR_INTEL, 0x6, 0xF, ANY, 110},		/* Intel Conroe */
 	{X86_VENDOR_INTEL, 0x6, ANY, ANY, 82},		/* any P6 */
 	{X86_VENDOR_INTEL, 0x7, ANY, ANY, 0},		/* Itanium */
 	{X86_VENDOR_INTEL, 0xF, 0x0, ANY, 90},		/* P4 */
diff --git a/drivers/hwmon/lm70.c b/drivers/hwmon/lm70.c
new file mode 100644
index 00000000000..6ba84731b9c
--- /dev/null
+++ b/drivers/hwmon/lm70.c
@@ -0,0 +1,165 @@
+/*
+ * lm70.c
+ *
+ * The LM70 is a temperature sensor chip from National Semiconductor (NS).
+ * Copyright (C) 2006 Kaiwan N Billimoria <kaiwan@designergraphix.com>
+ *
+ * The LM70 communicates with a host processor via an SPI/Microwire Bus
+ * interface. The complete datasheet is available at National's website
+ * here:
+ * http://www.national.com/pf/LM/LM70.html
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/sysfs.h>
+#include <linux/hwmon.h>
+#include <linux/spi/spi.h>
+#include <asm/semaphore.h>
+
+#define DRVNAME		"lm70"
+
+struct lm70 {
+	struct class_device *cdev;
+	struct semaphore sem;
+};
+
+/* sysfs hook function */
+static ssize_t lm70_sense_temp(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	int status, val;
+	u8 rxbuf[2];
+	s16 raw=0;
+	struct lm70 *p_lm70 = dev_get_drvdata(&spi->dev);
+
+	if (down_interruptible(&p_lm70->sem))
+		return -ERESTARTSYS;
+
+	/*
+	 * spi_read() requires a DMA-safe buffer; so we use
+	 * spi_write_then_read(), transmitting 0 bytes.
+	 */
+	status = spi_write_then_read(spi, NULL, 0, &rxbuf[0], 2);
+	if (status < 0) {
+		printk(KERN_WARNING
+		"spi_write_then_read failed with status %d\n", status);
+		goto out;
+	}
+	dev_dbg(dev, "rxbuf[1] : 0x%x rxbuf[0] : 0x%x\n", rxbuf[1], rxbuf[0]);
+
+	raw = (rxbuf[1] << 8) + rxbuf[0];
+	dev_dbg(dev, "raw=0x%x\n", raw);
+
+	/*
+	 * The "raw" temperature read into rxbuf[] is a 16-bit signed 2's
+	 * complement value. Only the MSB 11 bits (1 sign + 10 temperature
+	 * bits) are meaningful; the LSB 5 bits are to be discarded.
+	 * See the datasheet.
+	 *
+	 * Further, each bit represents 0.25 degrees Celsius; so, multiply
+	 * by 0.25. Also multiply by 1000 to represent in millidegrees
+	 * Celsius.
+	 * So it's equivalent to multiplying by 0.25 * 1000 = 250.
+	 */
+	val = ((int)raw/32) * 250;
+	status = sprintf(buf, "%+d\n", val); /* millidegrees Celsius */
+out:
+	up(&p_lm70->sem);
+	return status;
+}
+
+static DEVICE_ATTR(temp1_input, S_IRUGO, lm70_sense_temp, NULL);
+
+/*----------------------------------------------------------------------*/
+
+static int __devinit lm70_probe(struct spi_device *spi)
+{
+	struct lm70 *p_lm70;
+	int status;
+
+	p_lm70 = kzalloc(sizeof *p_lm70, GFP_KERNEL);
+	if (!p_lm70)
+		return -ENOMEM;
+
+	init_MUTEX(&p_lm70->sem);
+
+	/* sysfs hook */
+	p_lm70->cdev = hwmon_device_register(&spi->dev);
+	if (IS_ERR(p_lm70->cdev)) {
+		dev_dbg(&spi->dev, "hwmon_device_register failed.\n");
+		status = PTR_ERR(p_lm70->cdev);
+		goto out_dev_reg_failed;
+	}
+	dev_set_drvdata(&spi->dev, p_lm70);
+
+	if ((status = device_create_file(&spi->dev, &dev_attr_temp1_input))) {
+		dev_dbg(&spi->dev, "device_create_file failure.\n");
+		goto out_dev_create_file_failed;
+	}
+
+	return 0;
+
+out_dev_create_file_failed:
+	hwmon_device_unregister(p_lm70->cdev);
+out_dev_reg_failed:
+	dev_set_drvdata(&spi->dev, NULL);
+	kfree(p_lm70);
+	return status;
+}
+
+static int __exit lm70_remove(struct spi_device *spi)
+{
+	struct lm70 *p_lm70 = dev_get_drvdata(&spi->dev);
+
+	device_remove_file(&spi->dev, &dev_attr_temp1_input);
+	hwmon_device_unregister(p_lm70->cdev);
+	dev_set_drvdata(&spi->dev, NULL);
+	kfree(p_lm70);
+
+	return 0;
+}
+
+static struct spi_driver lm70_driver = {
+	.driver = {
+		.name	= "lm70",
+		.owner	= THIS_MODULE,
+	},
+	.probe	= lm70_probe,
+	.remove	= __devexit_p(lm70_remove),
+};
+
+static int __init init_lm70(void)
+{
+	return spi_register_driver(&lm70_driver);
+}
+
+static void __exit cleanup_lm70(void)
+{
+	spi_unregister_driver(&lm70_driver);
+}
+
+module_init(init_lm70);
+module_exit(cleanup_lm70);
+
+MODULE_AUTHOR("Kaiwan N Billimoria");
+MODULE_DESCRIPTION("National Semiconductor LM70 Linux driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/hwmon/lm83.c b/drivers/hwmon/lm83.c
index aac4ec2bf69..2137d7879df 100644
--- a/drivers/hwmon/lm83.c
+++ b/drivers/hwmon/lm83.c
@@ -12,6 +12,10 @@
  * Since the datasheet omits to give the chip stepping code, I give it
  * here: 0x03 (at register 0xff).
  *
+ * Also supports the LM82 temp sensor, which is basically a stripped down
+ * model of the LM83.  Datasheet is here:
+ * http://www.national.com/pf/LM/LM82.html
+ *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
@@ -52,7 +56,7 @@ static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a,
  * Insmod parameters
  */
 
-I2C_CLIENT_INSMOD_1(lm83);
+I2C_CLIENT_INSMOD_2(lm83, lm82);
 
 /*
  * The LM83 registers
@@ -283,6 +287,9 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind)
 		if (man_id == 0x01) { /* National Semiconductor */
 			if (chip_id == 0x03) {
 				kind = lm83;
+			} else
+			if (chip_id == 0x01) {
+				kind = lm82;
 			}
 		}
 
@@ -296,6 +303,9 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind)
 
 	if (kind == lm83) {
 		name = "lm83";
+	} else
+	if (kind == lm82) {
+		name = "lm82";
 	}
 
 	/* We can fill in the remaining client fields */
@@ -319,32 +329,46 @@ static int lm83_detect(struct i2c_adapter *adapter, int address, int kind)
 		goto exit_detach;
 	}
 
+	/*
+	 * The LM82 can only monitor one external diode which is
+	 * at the same register as the LM83 temp3 entry - so we
+	 * declare 1 and 3 common, and then 2 and 4 only for the LM83.
+	 */
+
 	device_create_file(&new_client->dev,
 			   &sensor_dev_attr_temp1_input.dev_attr);
 	device_create_file(&new_client->dev,
-			   &sensor_dev_attr_temp2_input.dev_attr);
-	device_create_file(&new_client->dev,
 			   &sensor_dev_attr_temp3_input.dev_attr);
-	device_create_file(&new_client->dev,
-			   &sensor_dev_attr_temp4_input.dev_attr);
+
 	device_create_file(&new_client->dev,
 			   &sensor_dev_attr_temp1_max.dev_attr);
 	device_create_file(&new_client->dev,
-			   &sensor_dev_attr_temp2_max.dev_attr);
-	device_create_file(&new_client->dev,
 			   &sensor_dev_attr_temp3_max.dev_attr);
-	device_create_file(&new_client->dev,
-			   &sensor_dev_attr_temp4_max.dev_attr);
+
 	device_create_file(&new_client->dev,
 			   &sensor_dev_attr_temp1_crit.dev_attr);
 	device_create_file(&new_client->dev,
-			   &sensor_dev_attr_temp2_crit.dev_attr);
-	device_create_file(&new_client->dev,
 			   &sensor_dev_attr_temp3_crit.dev_attr);
-	device_create_file(&new_client->dev,
-			   &sensor_dev_attr_temp4_crit.dev_attr);
+
 	device_create_file(&new_client->dev, &dev_attr_alarms);
 
+	if (kind == lm83) {
+		device_create_file(&new_client->dev,
+				   &sensor_dev_attr_temp2_input.dev_attr);
+		device_create_file(&new_client->dev,
+				   &sensor_dev_attr_temp4_input.dev_attr);
+
+		device_create_file(&new_client->dev,
+				   &sensor_dev_attr_temp2_max.dev_attr);
+		device_create_file(&new_client->dev,
+				   &sensor_dev_attr_temp4_max.dev_attr);
+
+		device_create_file(&new_client->dev,
+				   &sensor_dev_attr_temp2_crit.dev_attr);
+		device_create_file(&new_client->dev,
+				   &sensor_dev_attr_temp4_crit.dev_attr);
+	}
+
 	return 0;
 
 exit_detach:
diff --git a/drivers/hwmon/smsc47m192.c b/drivers/hwmon/smsc47m192.c
new file mode 100644
index 00000000000..bdc4570acf9
--- /dev/null
+++ b/drivers/hwmon/smsc47m192.c
@@ -0,0 +1,648 @@
+/*
+    smsc47m192.c - Support for hardware monitoring block of
+                   SMSC LPC47M192 and LPC47M997 Super I/O chips
+
+    Copyright (C) 2006  Hartmut Rick <linux@rick.claranet.de>
+
+    Derived from lm78.c and other chip drivers.
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
+#include <linux/err.h>
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2c, 0x2d, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(smsc47m192);
+
+/* SMSC47M192 registers */
+#define SMSC47M192_REG_IN(nr)		((nr)<6 ? (0x20 + (nr)) : \
+					(0x50 + (nr) - 6))
+#define SMSC47M192_REG_IN_MAX(nr)	((nr)<6 ? (0x2b + (nr) * 2) : \
+					(0x54 + (((nr) - 6) * 2)))
+#define SMSC47M192_REG_IN_MIN(nr)	((nr)<6 ? (0x2c + (nr) * 2) : \
+					(0x55 + (((nr) - 6) * 2)))
+static u8 SMSC47M192_REG_TEMP[3] =	{ 0x27, 0x26, 0x52 };
+static u8 SMSC47M192_REG_TEMP_MAX[3] =	{ 0x39, 0x37, 0x58 };
+static u8 SMSC47M192_REG_TEMP_MIN[3] =	{ 0x3A, 0x38, 0x59 };
+#define SMSC47M192_REG_TEMP_OFFSET(nr)	((nr)==2 ? 0x1e : 0x1f)
+#define SMSC47M192_REG_ALARM1		0x41
+#define SMSC47M192_REG_ALARM2		0x42
+#define SMSC47M192_REG_VID		0x47
+#define SMSC47M192_REG_VID4		0x49
+#define SMSC47M192_REG_CONFIG		0x40
+#define SMSC47M192_REG_SFR		0x4f
+#define SMSC47M192_REG_COMPANY_ID	0x3e
+#define SMSC47M192_REG_VERSION		0x3f
+
+/* generalised scaling with integer rounding */
+static inline int SCALE(long val, int mul, int div)
+{
+	if (val < 0)
+		return (val * mul - div / 2) / div;
+	else
+		return (val * mul + div / 2) / div;
+}
+
+/* Conversions */
+
+/* smsc47m192 internally scales voltage measurements */
+static const u16 nom_mv[] = { 2500, 2250, 3300, 5000, 12000, 3300, 1500, 1800 };
+
+static inline unsigned int IN_FROM_REG(u8 reg, int n)
+{
+	return SCALE(reg, nom_mv[n], 192);
+}
+
+static inline u8 IN_TO_REG(unsigned long val, int n)
+{
+	return SENSORS_LIMIT(SCALE(val, 192, nom_mv[n]), 0, 255);
+}
+
+/* TEMP: 0.001 degC units (-128C to +127C)
+   REG: 1C/bit, two's complement */
+static inline s8 TEMP_TO_REG(int val)
+{
+	return SENSORS_LIMIT(SCALE(val, 1, 1000), -128000, 127000);
+}
+
+static inline int TEMP_FROM_REG(s8 val)
+{
+	return val * 1000;
+}
+
+struct smsc47m192_data {
+	struct i2c_client client;
+	struct class_device *class_dev;
+	struct semaphore update_lock;
+	char valid;		/* !=0 if following fields are valid */
+	unsigned long last_updated;	/* In jiffies */
+
+	u8 in[8];		/* Register value */
+	u8 in_max[8];		/* Register value */
+	u8 in_min[8];		/* Register value */
+	s8 temp[3];		/* Register value */
+	s8 temp_max[3];		/* Register value */
+	s8 temp_min[3];		/* Register value */
+	s8 temp_offset[3];	/* Register value */
+	u16 alarms;		/* Register encoding, combined */
+	u8 vid;			/* Register encoding, combined */
+	u8 vrm;
+};
+
+static int smsc47m192_attach_adapter(struct i2c_adapter *adapter);
+static int smsc47m192_detect(struct i2c_adapter *adapter, int address,
+		int kind);
+static int smsc47m192_detach_client(struct i2c_client *client);
+static struct smsc47m192_data *smsc47m192_update_device(struct device *dev);
+
+static struct i2c_driver smsc47m192_driver = {
+	.driver = {
+		.name	= "smsc47m192",
+	},
+	.attach_adapter	= smsc47m192_attach_adapter,
+	.detach_client	= smsc47m192_detach_client,
+};
+
+/* Voltages */
+static ssize_t show_in(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", IN_FROM_REG(data->in[nr], nr));
+}
+
+static ssize_t show_in_min(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", IN_FROM_REG(data->in_min[nr], nr));
+}
+
+static ssize_t show_in_max(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", IN_FROM_REG(data->in_max[nr], nr));
+}
+
+static ssize_t set_in_min(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	unsigned long val = simple_strtoul(buf, NULL, 10);
+
+	down(&data->update_lock);
+	data->in_min[nr] = IN_TO_REG(val, nr);
+	i2c_smbus_write_byte_data(client, SMSC47M192_REG_IN_MIN(nr),
+							data->in_min[nr]);
+	up(&data->update_lock);
+	return count;
+}
+
+static ssize_t set_in_max(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	unsigned long val = simple_strtoul(buf, NULL, 10);
+
+	down(&data->update_lock);
+	data->in_max[nr] = IN_TO_REG(val, nr);
+	i2c_smbus_write_byte_data(client, SMSC47M192_REG_IN_MAX(nr),
+							data->in_max[nr]);
+	up(&data->update_lock);
+	return count;
+}
+
+#define show_in_offset(offset)					\
+static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO,		\
+		show_in, NULL, offset);				\
+static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR,	\
+		show_in_min, set_in_min, offset);		\
+static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR,	\
+		show_in_max, set_in_max, offset);
+
+show_in_offset(0)
+show_in_offset(1)
+show_in_offset(2)
+show_in_offset(3)
+show_in_offset(4)
+show_in_offset(5)
+show_in_offset(6)
+show_in_offset(7)
+
+/* Temperatures */
+static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp[nr]));
+}
+
+static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_min[nr]));
+}
+
+static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_max[nr]));
+}
+
+static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	long val = simple_strtol(buf, NULL, 10);
+
+	down(&data->update_lock);
+	data->temp_min[nr] = TEMP_TO_REG(val);
+	i2c_smbus_write_byte_data(client, SMSC47M192_REG_TEMP_MIN[nr],
+						data->temp_min[nr]);
+	up(&data->update_lock);
+	return count;
+}
+
+static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	long val = simple_strtol(buf, NULL, 10);
+
+	down(&data->update_lock);
+	data->temp_max[nr] = TEMP_TO_REG(val);
+	i2c_smbus_write_byte_data(client, SMSC47M192_REG_TEMP_MAX[nr],
+						data->temp_max[nr]);
+	up(&data->update_lock);
+	return count;
+}
+
+static ssize_t show_temp_offset(struct device *dev, struct device_attribute
+		*attr, char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_offset[nr]));
+}
+
+static ssize_t set_temp_offset(struct device *dev, struct device_attribute
+		*attr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct i2c_client *client = to_i2c_client(dev);
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	u8 sfr = i2c_smbus_read_byte_data(client, SMSC47M192_REG_SFR);
+	long val = simple_strtol(buf, NULL, 10);
+
+	down(&data->update_lock);
+	data->temp_offset[nr] = TEMP_TO_REG(val);
+	if (nr>1)
+		i2c_smbus_write_byte_data(client,
+			SMSC47M192_REG_TEMP_OFFSET(nr), data->temp_offset[nr]);
+	else if (data->temp_offset[nr] != 0) {
+		/* offset[0] and offset[1] share the same register,
+			SFR bit 4 activates offset[0] */
+		i2c_smbus_write_byte_data(client, SMSC47M192_REG_SFR,
+					(sfr & 0xef) | (nr==0 ? 0x10 : 0));
+		data->temp_offset[1-nr] = 0;
+		i2c_smbus_write_byte_data(client,
+			SMSC47M192_REG_TEMP_OFFSET(nr), data->temp_offset[nr]);
+	} else if ((sfr & 0x10) == (nr==0 ? 0x10 : 0))
+		i2c_smbus_write_byte_data(client,
+					SMSC47M192_REG_TEMP_OFFSET(nr), 0);
+	up(&data->update_lock);
+	return count;
+}
+
+#define show_temp_index(index)						\
+static SENSOR_DEVICE_ATTR(temp##index##_input, S_IRUGO,			\
+		show_temp, NULL, index-1);				\
+static SENSOR_DEVICE_ATTR(temp##index##_min, S_IRUGO | S_IWUSR,		\
+		show_temp_min, set_temp_min, index-1);			\
+static SENSOR_DEVICE_ATTR(temp##index##_max, S_IRUGO | S_IWUSR,		\
+		show_temp_max, set_temp_max, index-1);			\
+static SENSOR_DEVICE_ATTR(temp##index##_offset, S_IRUGO | S_IWUSR,	\
+		show_temp_offset, set_temp_offset, index-1);
+
+show_temp_index(1)
+show_temp_index(2)
+show_temp_index(3)
+
+/* VID */
+static ssize_t show_vid(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
+}
+static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL);
+
+static ssize_t show_vrm(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%d\n", data->vrm);
+}
+
+static ssize_t set_vrm(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	data->vrm = simple_strtoul(buf, NULL, 10);
+	return count;
+}
+static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm);
+
+/* Alarms */
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct smsc47m192_data *data = smsc47m192_update_device(dev);
+	return sprintf(buf, "%u\n", (data->alarms & nr) ? 1 : 0);
+}
+
+static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 0x0010);
+static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 0x0020);
+static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 0x0040);
+static SENSOR_DEVICE_ATTR(temp2_input_fault, S_IRUGO, show_alarm, NULL, 0x4000);
+static SENSOR_DEVICE_ATTR(temp3_input_fault, S_IRUGO, show_alarm, NULL, 0x8000);
+static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0x0001);
+static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 0x0002);
+static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 0x0004);
+static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 0x0008);
+static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 0x0100);
+static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 0x0200);
+static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 0x0400);
+static SENSOR_DEVICE_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 0x0800);
+
+/* This function is called when:
+    * smsc47m192_driver is inserted (when this module is loaded), for each
+      available adapter
+    * when a new adapter is inserted (and smsc47m192_driver is still present) */
+static int smsc47m192_attach_adapter(struct i2c_adapter *adapter)
+{
+	if (!(adapter->class & I2C_CLASS_HWMON))
+		return 0;
+	return i2c_probe(adapter, &addr_data, smsc47m192_detect);
+}
+
+static void smsc47m192_init_client(struct i2c_client *client)
+{
+	int i;
+	u8 config = i2c_smbus_read_byte_data(client, SMSC47M192_REG_CONFIG);
+	u8 sfr = i2c_smbus_read_byte_data(client, SMSC47M192_REG_SFR);
+
+	/* select cycle mode (pause 1 sec between updates) */
+	i2c_smbus_write_byte_data(client, SMSC47M192_REG_SFR,
+						(sfr & 0xfd) | 0x02);
+	if (!(config & 0x01)) {
+		/* initialize alarm limits */
+		for (i=0; i<8; i++) {
+			i2c_smbus_write_byte_data(client,
+				SMSC47M192_REG_IN_MIN(i), 0);
+			i2c_smbus_write_byte_data(client,
+				SMSC47M192_REG_IN_MAX(i), 0xff);
+		}
+		for (i=0; i<3; i++) {
+			i2c_smbus_write_byte_data(client,
+				SMSC47M192_REG_TEMP_MIN[i], 0x80);
+			i2c_smbus_write_byte_data(client,
+				SMSC47M192_REG_TEMP_MAX[i], 0x7f);
+		}
+
+		/* start monitoring */
+		i2c_smbus_write_byte_data(client, SMSC47M192_REG_CONFIG,
+						(config & 0xf7) | 0x01);
+	}
+}
+
+/* This function is called by i2c_probe */
+static int smsc47m192_detect(struct i2c_adapter *adapter, int address,
+		int kind)
+{
+	struct i2c_client *client;
+	struct smsc47m192_data *data;
+	int err = 0;
+	int version, config;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+		goto exit;
+
+	if (!(data = kzalloc(sizeof(struct smsc47m192_data), GFP_KERNEL))) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &smsc47m192_driver;
+
+	if (kind == 0)
+		kind = smsc47m192;
+
+	/* Detection criteria from sensors_detect script */
+	if (kind < 0) {
+		if (i2c_smbus_read_byte_data(client,
+				SMSC47M192_REG_COMPANY_ID) == 0x55
+		 && ((version = i2c_smbus_read_byte_data(client,
+				SMSC47M192_REG_VERSION)) & 0xf0) == 0x20
+		 && (i2c_smbus_read_byte_data(client,
+				SMSC47M192_REG_VID) & 0x70) == 0x00
+		 && (i2c_smbus_read_byte_data(client,
+				SMSC47M192_REG_VID4) & 0xfe) == 0x80) {
+			dev_info(&adapter->dev,
+				 "found SMSC47M192 or SMSC47M997, "
+				 "version 2, stepping A%d\n", version & 0x0f);
+		} else {
+			dev_dbg(&adapter->dev,
+				"SMSC47M192 detection failed at 0x%02x\n",
+				address);
+			goto exit_free;
+		}
+	}
+
+	/* Fill in the remaining client fields and put into the global list */
+	strlcpy(client->name, "smsc47m192", I2C_NAME_SIZE);
+	data->vrm = vid_which_vrm();
+	init_MUTEX(&data->update_lock);
+
+	/* Tell the I2C layer a new client has arrived */
+	if ((err = i2c_attach_client(client)))
+		goto exit_free;
+
+	/* Initialize the SMSC47M192 chip */
+	smsc47m192_init_client(client);
+
+	/* Register sysfs hooks */
+	data->class_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(data->class_dev)) {
+		err = PTR_ERR(data->class_dev);
+		goto exit_detach;
+	}
+
+	device_create_file(&client->dev, &sensor_dev_attr_in0_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in0_min.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in0_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in0_alarm.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in1_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in1_min.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in1_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in1_alarm.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in2_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in2_min.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in2_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in2_alarm.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in3_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in3_min.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in3_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in3_alarm.dev_attr);
+
+	/* Pin 110 is either in4 (+12V) or VID4 */
+	config = i2c_smbus_read_byte_data(client, SMSC47M192_REG_CONFIG);
+	if (!(config & 0x20)) {
+		device_create_file(&client->dev,
+				   &sensor_dev_attr_in4_input.dev_attr);
+		device_create_file(&client->dev,
+				   &sensor_dev_attr_in4_min.dev_attr);
+		device_create_file(&client->dev,
+				   &sensor_dev_attr_in4_max.dev_attr);
+		device_create_file(&client->dev,
+				   &sensor_dev_attr_in4_alarm.dev_attr);
+	}
+	device_create_file(&client->dev, &sensor_dev_attr_in5_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in5_min.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in5_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in5_alarm.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in6_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in6_min.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in6_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in6_alarm.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in7_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in7_min.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in7_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_in7_alarm.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp1_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp1_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp1_min.dev_attr);
+	device_create_file(&client->dev,
+			   &sensor_dev_attr_temp1_offset.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp1_alarm.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp2_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp2_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp2_min.dev_attr);
+	device_create_file(&client->dev,
+			   &sensor_dev_attr_temp2_offset.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp2_alarm.dev_attr);
+	device_create_file(&client->dev,
+			   &sensor_dev_attr_temp2_input_fault.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp3_input.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp3_max.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp3_min.dev_attr);
+	device_create_file(&client->dev,
+			   &sensor_dev_attr_temp3_offset.dev_attr);
+	device_create_file(&client->dev, &sensor_dev_attr_temp3_alarm.dev_attr);
+	device_create_file(&client->dev,
+			   &sensor_dev_attr_temp3_input_fault.dev_attr);
+	device_create_file(&client->dev, &dev_attr_cpu0_vid);
+	device_create_file(&client->dev, &dev_attr_vrm);
+
+	return 0;
+
+exit_detach:
+	i2c_detach_client(client);
+exit_free:
+	kfree(data);
+exit:
+	return err;
+}
+
+static int smsc47m192_detach_client(struct i2c_client *client)
+{
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	int err;
+
+	hwmon_device_unregister(data->class_dev);
+
+	if ((err = i2c_detach_client(client)))
+		return err;
+
+	kfree(data);
+
+	return 0;
+}
+
+static struct smsc47m192_data *smsc47m192_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct smsc47m192_data *data = i2c_get_clientdata(client);
+	int i, config;
+
+	down(&data->update_lock);
+
+	if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
+	 || !data->valid) {
+		u8 sfr = i2c_smbus_read_byte_data(client, SMSC47M192_REG_SFR);
+
+		dev_dbg(&client->dev, "Starting smsc47m192 update\n");
+
+		for (i = 0; i <= 7; i++) {
+			data->in[i] = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_IN(i));
+			data->in_min[i] = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_IN_MIN(i));
+			data->in_max[i] = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_IN_MAX(i));
+		}
+		for (i = 0; i < 3; i++) {
+			data->temp[i] = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_TEMP[i]);
+			data->temp_max[i] = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_TEMP_MAX[i]);
+			data->temp_min[i] = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_TEMP_MIN[i]);
+		}
+		for (i = 1; i < 3; i++)
+			data->temp_offset[i] = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_TEMP_OFFSET(i));
+		/* first offset is temp_offset[0] if SFR bit 4 is set,
+					temp_offset[1] otherwise */
+		if (sfr & 0x10) {
+			data->temp_offset[0] = data->temp_offset[1];
+			data->temp_offset[1] = 0;
+		} else
+			data->temp_offset[0] = 0;
+
+		data->vid = i2c_smbus_read_byte_data(client, SMSC47M192_REG_VID)
+			    & 0x0f;
+		config = i2c_smbus_read_byte_data(client,
+						  SMSC47M192_REG_CONFIG);
+		if (config & 0x20)
+			data->vid |= (i2c_smbus_read_byte_data(client,
+					SMSC47M192_REG_VID4) & 0x01) << 4;
+		data->alarms = i2c_smbus_read_byte_data(client,
+						SMSC47M192_REG_ALARM1) |
+			       (i2c_smbus_read_byte_data(client,
+		       				SMSC47M192_REG_ALARM2) << 8);
+
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+
+	up(&data->update_lock);
+
+	return data;
+}
+
+static int __init smsc47m192_init(void)
+{
+	return i2c_add_driver(&smsc47m192_driver);
+}
+
+static void __exit smsc47m192_exit(void)
+{
+	i2c_del_driver(&smsc47m192_driver);
+}
+
+MODULE_AUTHOR("Hartmut Rick <linux@rick.claranet.de>");
+MODULE_DESCRIPTION("SMSC47M192 driver");
+MODULE_LICENSE("GPL");
+
+module_init(smsc47m192_init);
+module_exit(smsc47m192_exit);
diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c
index b6bd5685fd3..40301bc6ce1 100644
--- a/drivers/hwmon/w83627ehf.c
+++ b/drivers/hwmon/w83627ehf.c
@@ -30,10 +30,7 @@
     Supports the following chips:
 
     Chip        #vin    #fan    #pwm    #temp   chip_id man_id
-    w83627ehf   -       5       -       3       0x88    0x5ca3
-
-    This is a preliminary version of the driver, only supporting the
-    fan and temperature inputs. The chip does much more than that.
+    w83627ehf   10      5       -       3       0x88    0x5ca3
 */
 
 #include <linux/module.h>
@@ -121,6 +118,14 @@ superio_exit(void)
 static const u16 W83627EHF_REG_FAN[] = { 0x28, 0x29, 0x2a, 0x3f, 0x553 };
 static const u16 W83627EHF_REG_FAN_MIN[] = { 0x3b, 0x3c, 0x3d, 0x3e, 0x55c };
 
+/* The W83627EHF registers for nr=7,8,9 are in bank 5 */
+#define W83627EHF_REG_IN_MAX(nr)	((nr < 7) ? (0x2b + (nr) * 2) : \
+					 (0x554 + (((nr) - 7) * 2)))
+#define W83627EHF_REG_IN_MIN(nr)	((nr < 7) ? (0x2c + (nr) * 2) : \
+					 (0x555 + (((nr) - 7) * 2)))
+#define W83627EHF_REG_IN(nr)		((nr < 7) ? (0x20 + (nr)) : \
+					 (0x550 + (nr) - 7))
+
 #define W83627EHF_REG_TEMP1		0x27
 #define W83627EHF_REG_TEMP1_HYST	0x3a
 #define W83627EHF_REG_TEMP1_OVER	0x39
@@ -136,6 +141,10 @@ static const u16 W83627EHF_REG_TEMP_CONFIG[] = { 0x152, 0x252 };
 #define W83627EHF_REG_DIODE		0x59
 #define W83627EHF_REG_SMI_OVT		0x4C
 
+#define W83627EHF_REG_ALARM1		0x459
+#define W83627EHF_REG_ALARM2		0x45A
+#define W83627EHF_REG_ALARM3		0x45B
+
 /*
  * Conversions
  */
@@ -172,6 +181,20 @@ temp1_to_reg(int temp)
 	return (temp + 500) / 1000;
 }
 
+/* Some of analog inputs have internal scaling (2x), 8mV is ADC LSB */
+
+static u8 scale_in[10] = { 8, 8, 16, 16, 8, 8, 8, 16, 16, 8 };
+
+static inline long in_from_reg(u8 reg, u8 nr)
+{
+	return reg * scale_in[nr];
+}
+
+static inline u8 in_to_reg(u32 val, u8 nr)
+{
+	return SENSORS_LIMIT(((val + (scale_in[nr] / 2)) / scale_in[nr]), 0, 255);
+}
+
 /*
  * Data structures and manipulation thereof
  */
@@ -186,6 +209,9 @@ struct w83627ehf_data {
 	unsigned long last_updated;	/* In jiffies */
 
 	/* Register values */
+	u8 in[10];		/* Register value */
+	u8 in_max[10];		/* Register value */
+	u8 in_min[10];		/* Register value */
 	u8 fan[5];
 	u8 fan_min[5];
 	u8 fan_div[5];
@@ -196,6 +222,7 @@ struct w83627ehf_data {
 	s16 temp[2];
 	s16 temp_max[2];
 	s16 temp_max_hyst[2];
+	u32 alarms;
 };
 
 static inline int is_word_sized(u16 reg)
@@ -349,6 +376,16 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
 			data->fan_div[3] |= (i >> 5) & 0x04;
 		}
 
+		/* Measured voltages and limits */
+		for (i = 0; i < 10; i++) {
+			data->in[i] = w83627ehf_read_value(client,
+				      W83627EHF_REG_IN(i));
+			data->in_min[i] = w83627ehf_read_value(client,
+					  W83627EHF_REG_IN_MIN(i));
+			data->in_max[i] = w83627ehf_read_value(client,
+					  W83627EHF_REG_IN_MAX(i));
+		}
+
 		/* Measured fan speeds and limits */
 		for (i = 0; i < 5; i++) {
 			if (!(data->has_fan & (1 << i)))
@@ -395,6 +432,13 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
 						 W83627EHF_REG_TEMP_HYST[i]);
 		}
 
+		data->alarms = w83627ehf_read_value(client,
+					W83627EHF_REG_ALARM1) |
+			       (w83627ehf_read_value(client,
+					W83627EHF_REG_ALARM2) << 8) |
+			       (w83627ehf_read_value(client,
+					W83627EHF_REG_ALARM3) << 16);
+
 		data->last_updated = jiffies;
 		data->valid = 1;
 	}
@@ -406,6 +450,109 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
 /*
  * Sysfs callback functions
  */
+#define show_in_reg(reg) \
+static ssize_t \
+show_##reg(struct device *dev, struct device_attribute *attr, \
+	   char *buf) \
+{ \
+	struct w83627ehf_data *data = w83627ehf_update_device(dev); \
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
+	int nr = sensor_attr->index; \
+	return sprintf(buf, "%ld\n", in_from_reg(data->reg[nr], nr)); \
+}
+show_in_reg(in)
+show_in_reg(in_min)
+show_in_reg(in_max)
+
+#define store_in_reg(REG, reg) \
+static ssize_t \
+store_in_##reg (struct device *dev, struct device_attribute *attr, \
+			const char *buf, size_t count) \
+{ \
+	struct i2c_client *client = to_i2c_client(dev); \
+	struct w83627ehf_data *data = i2c_get_clientdata(client); \
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr); \
+	int nr = sensor_attr->index; \
+	u32 val = simple_strtoul(buf, NULL, 10); \
+ \
+	mutex_lock(&data->update_lock); \
+	data->in_##reg[nr] = in_to_reg(val, nr); \
+	w83627ehf_write_value(client, W83627EHF_REG_IN_##REG(nr), \
+			      data->in_##reg[nr]); \
+	mutex_unlock(&data->update_lock); \
+	return count; \
+}
+
+store_in_reg(MIN, min)
+store_in_reg(MAX, max)
+
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct w83627ehf_data *data = w83627ehf_update_device(dev);
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	return sprintf(buf, "%u\n", (data->alarms >> nr) & 0x01);
+}
+
+static struct sensor_device_attribute sda_in_input[] = {
+	SENSOR_ATTR(in0_input, S_IRUGO, show_in, NULL, 0),
+	SENSOR_ATTR(in1_input, S_IRUGO, show_in, NULL, 1),
+	SENSOR_ATTR(in2_input, S_IRUGO, show_in, NULL, 2),
+	SENSOR_ATTR(in3_input, S_IRUGO, show_in, NULL, 3),
+	SENSOR_ATTR(in4_input, S_IRUGO, show_in, NULL, 4),
+	SENSOR_ATTR(in5_input, S_IRUGO, show_in, NULL, 5),
+	SENSOR_ATTR(in6_input, S_IRUGO, show_in, NULL, 6),
+	SENSOR_ATTR(in7_input, S_IRUGO, show_in, NULL, 7),
+	SENSOR_ATTR(in8_input, S_IRUGO, show_in, NULL, 8),
+	SENSOR_ATTR(in9_input, S_IRUGO, show_in, NULL, 9),
+};
+
+static struct sensor_device_attribute sda_in_alarm[] = {
+	SENSOR_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0),
+	SENSOR_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1),
+	SENSOR_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2),
+	SENSOR_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3),
+	SENSOR_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8),
+	SENSOR_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 21),
+	SENSOR_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 20),
+	SENSOR_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 16),
+	SENSOR_ATTR(in8_alarm, S_IRUGO, show_alarm, NULL, 17),
+	SENSOR_ATTR(in9_alarm, S_IRUGO, show_alarm, NULL, 19),
+};
+
+static struct sensor_device_attribute sda_in_min[] = {
+       SENSOR_ATTR(in0_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 0),
+       SENSOR_ATTR(in1_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 1),
+       SENSOR_ATTR(in2_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 2),
+       SENSOR_ATTR(in3_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 3),
+       SENSOR_ATTR(in4_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 4),
+       SENSOR_ATTR(in5_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 5),
+       SENSOR_ATTR(in6_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 6),
+       SENSOR_ATTR(in7_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 7),
+       SENSOR_ATTR(in8_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 8),
+       SENSOR_ATTR(in9_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 9),
+};
+
+static struct sensor_device_attribute sda_in_max[] = {
+       SENSOR_ATTR(in0_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 0),
+       SENSOR_ATTR(in1_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 1),
+       SENSOR_ATTR(in2_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 2),
+       SENSOR_ATTR(in3_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 3),
+       SENSOR_ATTR(in4_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 4),
+       SENSOR_ATTR(in5_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 5),
+       SENSOR_ATTR(in6_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 6),
+       SENSOR_ATTR(in7_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 7),
+       SENSOR_ATTR(in8_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 8),
+       SENSOR_ATTR(in9_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 9),
+};
+
+static void device_create_file_in(struct device *dev, int i)
+{
+	device_create_file(dev, &sda_in_input[i].dev_attr);
+	device_create_file(dev, &sda_in_alarm[i].dev_attr);
+	device_create_file(dev, &sda_in_min[i].dev_attr);
+	device_create_file(dev, &sda_in_max[i].dev_attr);
+}
 
 #define show_fan_reg(reg) \
 static ssize_t \
@@ -505,6 +652,14 @@ static struct sensor_device_attribute sda_fan_input[] = {
 	SENSOR_ATTR(fan5_input, S_IRUGO, show_fan, NULL, 4),
 };
 
+static struct sensor_device_attribute sda_fan_alarm[] = {
+	SENSOR_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6),
+	SENSOR_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7),
+	SENSOR_ATTR(fan3_alarm, S_IRUGO, show_alarm, NULL, 11),
+	SENSOR_ATTR(fan4_alarm, S_IRUGO, show_alarm, NULL, 10),
+	SENSOR_ATTR(fan5_alarm, S_IRUGO, show_alarm, NULL, 23),
+};
+
 static struct sensor_device_attribute sda_fan_min[] = {
 	SENSOR_ATTR(fan1_min, S_IWUSR | S_IRUGO, show_fan_min,
 		    store_fan_min, 0),
@@ -529,6 +684,7 @@ static struct sensor_device_attribute sda_fan_div[] = {
 static void device_create_file_fan(struct device *dev, int i)
 {
 	device_create_file(dev, &sda_fan_input[i].dev_attr);
+	device_create_file(dev, &sda_fan_alarm[i].dev_attr);
 	device_create_file(dev, &sda_fan_div[i].dev_attr);
 	device_create_file(dev, &sda_fan_min[i].dev_attr);
 }
@@ -616,6 +772,9 @@ static struct sensor_device_attribute sda_temp[] = {
 		    store_temp_max_hyst, 0),
 	SENSOR_ATTR(temp3_max_hyst, S_IRUGO | S_IWUSR, show_temp_max_hyst,
 		    store_temp_max_hyst, 1),
+	SENSOR_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4),
+	SENSOR_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5),
+	SENSOR_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 13),
 };
 
 /*
@@ -705,6 +864,9 @@ static int w83627ehf_detect(struct i2c_adapter *adapter)
 		goto exit_detach;
 	}
 
+	for (i = 0; i < 10; i++)
+		device_create_file_in(dev, i);
+
 	for (i = 0; i < 5; i++) {
 		if (data->has_fan & (1 << i))
 			device_create_file_fan(dev, i);
diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c
new file mode 100644
index 00000000000..eec43abd57f
--- /dev/null
+++ b/drivers/hwmon/w83791d.c
@@ -0,0 +1,1255 @@
+/*
+    w83791d.c - Part of lm_sensors, Linux kernel modules for hardware
+                monitoring
+
+    Copyright (C) 2006 Charles Spirakis <bezaur@gmail.com>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+/*
+    Supports following chips:
+
+    Chip	#vin	#fanin	#pwm	#temp	wchipid	vendid	i2c	ISA
+    w83791d	10	5	3	3	0x71	0x5ca3	yes	no
+
+    The w83791d chip appears to be part way between the 83781d and the
+    83792d. Thus, this file is derived from both the w83792d.c and
+    w83781d.c files, but its output is more along the lines of the
+    83781d (which means there are no changes to the user-mode sensors
+    program which treats the 83791d as an 83781d).
+*/
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-vid.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+
+#define NUMBER_OF_VIN		10
+#define NUMBER_OF_FANIN		5
+#define NUMBER_OF_TEMPIN	3
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_1(w83791d);
+I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: "
+			"{bus, clientaddr, subclientaddr1, subclientaddr2}");
+
+static int reset;
+module_param(reset, bool, 0);
+MODULE_PARM_DESC(reset, "Set to one to force a hardware chip reset");
+
+static int init;
+module_param(init, bool, 0);
+MODULE_PARM_DESC(init, "Set to one to force extra software initialization");
+
+/* The W83791D registers */
+static const u8 W83791D_REG_IN[NUMBER_OF_VIN] = {
+	0x20,			/* VCOREA in DataSheet */
+	0x21,			/* VINR0 in DataSheet */
+	0x22,			/* +3.3VIN in DataSheet */
+	0x23,			/* VDD5V in DataSheet */
+	0x24,			/* +12VIN in DataSheet */
+	0x25,			/* -12VIN in DataSheet */
+	0x26,			/* -5VIN in DataSheet */
+	0xB0,			/* 5VSB in DataSheet */
+	0xB1,			/* VBAT in DataSheet */
+	0xB2			/* VINR1 in DataSheet */
+};
+
+static const u8 W83791D_REG_IN_MAX[NUMBER_OF_VIN] = {
+	0x2B,			/* VCOREA High Limit in DataSheet */
+	0x2D,			/* VINR0 High Limit in DataSheet */
+	0x2F,			/* +3.3VIN High Limit in DataSheet */
+	0x31,			/* VDD5V High Limit in DataSheet */
+	0x33,			/* +12VIN High Limit in DataSheet */
+	0x35,			/* -12VIN High Limit in DataSheet */
+	0x37,			/* -5VIN High Limit in DataSheet */
+	0xB4,			/* 5VSB High Limit in DataSheet */
+	0xB6,			/* VBAT High Limit in DataSheet */
+	0xB8			/* VINR1 High Limit in DataSheet */
+};
+static const u8 W83791D_REG_IN_MIN[NUMBER_OF_VIN] = {
+	0x2C,			/* VCOREA Low Limit in DataSheet */
+	0x2E,			/* VINR0 Low Limit in DataSheet */
+	0x30,			/* +3.3VIN Low Limit in DataSheet */
+	0x32,			/* VDD5V Low Limit in DataSheet */
+	0x34,			/* +12VIN Low Limit in DataSheet */
+	0x36,			/* -12VIN Low Limit in DataSheet */
+	0x38,			/* -5VIN Low Limit in DataSheet */
+	0xB5,			/* 5VSB Low Limit in DataSheet */
+	0xB7,			/* VBAT Low Limit in DataSheet */
+	0xB9			/* VINR1 Low Limit in DataSheet */
+};
+static const u8 W83791D_REG_FAN[NUMBER_OF_FANIN] = {
+	0x28,			/* FAN 1 Count in DataSheet */
+	0x29,			/* FAN 2 Count in DataSheet */
+	0x2A,			/* FAN 3 Count in DataSheet */
+	0xBA,			/* FAN 4 Count in DataSheet */
+	0xBB,			/* FAN 5 Count in DataSheet */
+};
+static const u8 W83791D_REG_FAN_MIN[NUMBER_OF_FANIN] = {
+	0x3B,			/* FAN 1 Count Low Limit in DataSheet */
+	0x3C,			/* FAN 2 Count Low Limit in DataSheet */
+	0x3D,			/* FAN 3 Count Low Limit in DataSheet */
+	0xBC,			/* FAN 4 Count Low Limit in DataSheet */
+	0xBD,			/* FAN 5 Count Low Limit in DataSheet */
+};
+
+static const u8 W83791D_REG_FAN_CFG[2] = {
+	0x84,			/* FAN 1/2 configuration */
+	0x95,			/* FAN 3 configuration */
+};
+
+static const u8 W83791D_REG_FAN_DIV[3] = {
+	0x47,			/* contains FAN1 and FAN2 Divisor */
+	0x4b,			/* contains FAN3 Divisor */
+	0x5C,			/* contains FAN4 and FAN5 Divisor */
+};
+
+#define W83791D_REG_BANK		0x4E
+#define W83791D_REG_TEMP2_CONFIG	0xC2
+#define W83791D_REG_TEMP3_CONFIG	0xCA
+
+static const u8 W83791D_REG_TEMP1[3] = {
+	0x27,			/* TEMP 1 in DataSheet */
+	0x39,			/* TEMP 1 Over in DataSheet */
+	0x3A,			/* TEMP 1 Hyst in DataSheet */
+};
+
+static const u8 W83791D_REG_TEMP_ADD[2][6] = {
+	{0xC0,			/* TEMP 2 in DataSheet */
+	 0xC1,			/* TEMP 2(0.5 deg) in DataSheet */
+	 0xC5,			/* TEMP 2 Over High part in DataSheet */
+	 0xC6,			/* TEMP 2 Over Low part in DataSheet */
+	 0xC3,			/* TEMP 2 Thyst High part in DataSheet */
+	 0xC4},			/* TEMP 2 Thyst Low part in DataSheet */
+	{0xC8,			/* TEMP 3 in DataSheet */
+	 0xC9,			/* TEMP 3(0.5 deg) in DataSheet */
+	 0xCD,			/* TEMP 3 Over High part in DataSheet */
+	 0xCE,			/* TEMP 3 Over Low part in DataSheet */
+	 0xCB,			/* TEMP 3 Thyst High part in DataSheet */
+	 0xCC}			/* TEMP 3 Thyst Low part in DataSheet */
+};
+
+#define W83791D_REG_BEEP_CONFIG		0x4D
+
+static const u8 W83791D_REG_BEEP_CTRL[3] = {
+	0x56,			/* BEEP Control Register 1 */
+	0x57,			/* BEEP Control Register 2 */
+	0xA3,			/* BEEP Control Register 3 */
+};
+
+#define W83791D_REG_CONFIG		0x40
+#define W83791D_REG_VID_FANDIV		0x47
+#define W83791D_REG_DID_VID4		0x49
+#define W83791D_REG_WCHIPID		0x58
+#define W83791D_REG_CHIPMAN		0x4F
+#define W83791D_REG_PIN			0x4B
+#define W83791D_REG_I2C_SUBADDR		0x4A
+
+#define W83791D_REG_ALARM1 0xA9	/* realtime status register1 */
+#define W83791D_REG_ALARM2 0xAA	/* realtime status register2 */
+#define W83791D_REG_ALARM3 0xAB	/* realtime status register3 */
+
+#define W83791D_REG_VBAT		0x5D
+#define W83791D_REG_I2C_ADDR		0x48
+
+/* The SMBus locks itself. The Winbond W83791D has a bank select register
+   (index 0x4e), but the driver only accesses registers in bank 0. Since
+   we don't switch banks, we don't need any special code to handle
+   locking access between bank switches */
+static inline int w83791d_read(struct i2c_client *client, u8 reg)
+{
+	return i2c_smbus_read_byte_data(client, reg);
+}
+
+static inline int w83791d_write(struct i2c_client *client, u8 reg, u8 value)
+{
+	return i2c_smbus_write_byte_data(client, reg, value);
+}
+
+/* The analog voltage inputs have 16mV LSB. Since the sysfs output is
+   in mV as would be measured on the chip input pin, need to just
+   multiply/divide by 16 to translate from/to register values. */
+#define IN_TO_REG(val)		(SENSORS_LIMIT((((val) + 8) / 16), 0, 255))
+#define IN_FROM_REG(val)	((val) * 16)
+
+static u8 fan_to_reg(long rpm, int div)
+{
+	if (rpm == 0)
+		return 255;
+	rpm = SENSORS_LIMIT(rpm, 1, 1000000);
+	return SENSORS_LIMIT((1350000 + rpm * div / 2) / (rpm * div), 1, 254);
+}
+
+#define FAN_FROM_REG(val,div)	((val) == 0   ? -1 : \
+				((val) == 255 ? 0 : \
+					1350000 / ((val) * (div))))
+
+/* for temp1 which is 8-bit resolution, LSB = 1 degree Celsius */
+#define TEMP1_FROM_REG(val)	((val) * 1000)
+#define TEMP1_TO_REG(val)	((val) <= -128000 ? -128 : \
+				 (val) >= 127000 ? 127 : \
+				 (val) < 0 ? ((val) - 500) / 1000 : \
+				 ((val) + 500) / 1000)
+
+/* for temp2 and temp3 which are 9-bit resolution, LSB = 0.5 degree Celsius
+   Assumes the top 8 bits are the integral amount and the bottom 8 bits
+   are the fractional amount. Since we only have 0.5 degree resolution,
+   the bottom 7 bits will always be zero */
+#define TEMP23_FROM_REG(val)	((val) / 128 * 500)
+#define TEMP23_TO_REG(val)	((val) <= -128000 ? 0x8000 : \
+				 (val) >= 127500 ? 0x7F80 : \
+				 (val) < 0 ? ((val) - 250) / 500 * 128 : \
+				 ((val) + 250) / 500 * 128)
+
+
+#define BEEP_MASK_TO_REG(val)		((val) & 0xffffff)
+#define BEEP_MASK_FROM_REG(val)		((val) & 0xffffff)
+
+#define DIV_FROM_REG(val)		(1 << (val))
+
+static u8 div_to_reg(int nr, long val)
+{
+	int i;
+	int max;
+
+	/* first three fan's divisor max out at 8, rest max out at 128 */
+	max = (nr < 3) ? 8 : 128;
+	val = SENSORS_LIMIT(val, 1, max) >> 1;
+	for (i = 0; i < 7; i++) {
+		if (val == 0)
+			break;
+		val >>= 1;
+	}
+	return (u8) i;
+}
+
+struct w83791d_data {
+	struct i2c_client client;
+	struct class_device *class_dev;
+	struct mutex update_lock;
+
+	char valid;			/* !=0 if following fields are valid */
+	unsigned long last_updated;	/* In jiffies */
+
+	/* array of 2 pointers to subclients */
+	struct i2c_client *lm75[2];
+
+	/* volts */
+	u8 in[NUMBER_OF_VIN];		/* Register value */
+	u8 in_max[NUMBER_OF_VIN];	/* Register value */
+	u8 in_min[NUMBER_OF_VIN];	/* Register value */
+
+	/* fans */
+	u8 fan[NUMBER_OF_FANIN];	/* Register value */
+	u8 fan_min[NUMBER_OF_FANIN];	/* Register value */
+	u8 fan_div[NUMBER_OF_FANIN];	/* Register encoding, shifted right */
+
+	/* Temperature sensors */
+
+	s8 temp1[3];		/* current, over, thyst */
+	s16 temp_add[2][3];	/* fixed point value. Top 8 bits are the
+				   integral part, bottom 8 bits are the
+				   fractional part. We only use the top
+				   9 bits as the resolution is only
+				   to the 0.5 degree C...
+				   two sensors with three values
+				   (cur, over, hyst)  */
+
+	/* Misc */
+	u32 alarms;		/* realtime status register encoding,combined */
+	u8 beep_enable;		/* Global beep enable */
+	u32 beep_mask;		/* Mask off specific beeps */
+	u8 vid;			/* Register encoding, combined */
+	u8 vrm;			/* hwmon-vid */
+};
+
+static int w83791d_attach_adapter(struct i2c_adapter *adapter);
+static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind);
+static int w83791d_detach_client(struct i2c_client *client);
+
+static int w83791d_read(struct i2c_client *client, u8 register);
+static int w83791d_write(struct i2c_client *client, u8 register, u8 value);
+static struct w83791d_data *w83791d_update_device(struct device *dev);
+
+#ifdef DEBUG
+static void w83791d_print_debug(struct w83791d_data *data, struct device *dev);
+#endif
+
+static void w83791d_init_client(struct i2c_client *client);
+
+static struct i2c_driver w83791d_driver = {
+	.driver = {
+		.name = "w83791d",
+	},
+	.attach_adapter = w83791d_attach_adapter,
+	.detach_client = w83791d_detach_client,
+};
+
+/* following are the sysfs callback functions */
+#define show_in_reg(reg) \
+static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
+			char *buf) \
+{ \
+	struct sensor_device_attribute *sensor_attr = \
+						to_sensor_dev_attr(attr); \
+	struct w83791d_data *data = w83791d_update_device(dev); \
+	int nr = sensor_attr->index; \
+	return sprintf(buf,"%d\n", IN_FROM_REG(data->reg[nr])); \
+}
+
+show_in_reg(in);
+show_in_reg(in_min);
+show_in_reg(in_max);
+
+#define store_in_reg(REG, reg) \
+static ssize_t store_in_##reg(struct device *dev, \
+				struct device_attribute *attr, \
+				const char *buf, size_t count) \
+{ \
+	struct sensor_device_attribute *sensor_attr = \
+						to_sensor_dev_attr(attr); \
+	struct i2c_client *client = to_i2c_client(dev); \
+	struct w83791d_data *data = i2c_get_clientdata(client); \
+	unsigned long val = simple_strtoul(buf, NULL, 10); \
+	int nr = sensor_attr->index; \
+	 \
+	mutex_lock(&data->update_lock); \
+	data->in_##reg[nr] = IN_TO_REG(val); \
+	w83791d_write(client, W83791D_REG_IN_##REG[nr], data->in_##reg[nr]); \
+	mutex_unlock(&data->update_lock); \
+	 \
+	return count; \
+}
+store_in_reg(MIN, min);
+store_in_reg(MAX, max);
+
+static struct sensor_device_attribute sda_in_input[] = {
+	SENSOR_ATTR(in0_input, S_IRUGO, show_in, NULL, 0),
+	SENSOR_ATTR(in1_input, S_IRUGO, show_in, NULL, 1),
+	SENSOR_ATTR(in2_input, S_IRUGO, show_in, NULL, 2),
+	SENSOR_ATTR(in3_input, S_IRUGO, show_in, NULL, 3),
+	SENSOR_ATTR(in4_input, S_IRUGO, show_in, NULL, 4),
+	SENSOR_ATTR(in5_input, S_IRUGO, show_in, NULL, 5),
+	SENSOR_ATTR(in6_input, S_IRUGO, show_in, NULL, 6),
+	SENSOR_ATTR(in7_input, S_IRUGO, show_in, NULL, 7),
+	SENSOR_ATTR(in8_input, S_IRUGO, show_in, NULL, 8),
+	SENSOR_ATTR(in9_input, S_IRUGO, show_in, NULL, 9),
+};
+
+static struct sensor_device_attribute sda_in_min[] = {
+	SENSOR_ATTR(in0_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 0),
+	SENSOR_ATTR(in1_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 1),
+	SENSOR_ATTR(in2_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 2),
+	SENSOR_ATTR(in3_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 3),
+	SENSOR_ATTR(in4_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 4),
+	SENSOR_ATTR(in5_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 5),
+	SENSOR_ATTR(in6_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 6),
+	SENSOR_ATTR(in7_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 7),
+	SENSOR_ATTR(in8_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 8),
+	SENSOR_ATTR(in9_min, S_IWUSR | S_IRUGO, show_in_min, store_in_min, 9),
+};
+
+static struct sensor_device_attribute sda_in_max[] = {
+	SENSOR_ATTR(in0_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 0),
+	SENSOR_ATTR(in1_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 1),
+	SENSOR_ATTR(in2_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 2),
+	SENSOR_ATTR(in3_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 3),
+	SENSOR_ATTR(in4_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 4),
+	SENSOR_ATTR(in5_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 5),
+	SENSOR_ATTR(in6_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 6),
+	SENSOR_ATTR(in7_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 7),
+	SENSOR_ATTR(in8_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 8),
+	SENSOR_ATTR(in9_max, S_IWUSR | S_IRUGO, show_in_max, store_in_max, 9),
+};
+
+#define show_fan_reg(reg) \
+static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
+				char *buf) \
+{ \
+	struct sensor_device_attribute *sensor_attr = \
+						to_sensor_dev_attr(attr); \
+	struct w83791d_data *data = w83791d_update_device(dev); \
+	int nr = sensor_attr->index; \
+	return sprintf(buf,"%d\n", \
+		FAN_FROM_REG(data->reg[nr], DIV_FROM_REG(data->fan_div[nr]))); \
+}
+
+show_fan_reg(fan);
+show_fan_reg(fan_min);
+
+static ssize_t store_fan_min(struct device *dev, struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	unsigned long val = simple_strtoul(buf, NULL, 10);
+	int nr = sensor_attr->index;
+
+	mutex_lock(&data->update_lock);
+	data->fan_min[nr] = fan_to_reg(val, DIV_FROM_REG(data->fan_div[nr]));
+	w83791d_write(client, W83791D_REG_FAN_MIN[nr], data->fan_min[nr]);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static ssize_t show_fan_div(struct device *dev, struct device_attribute *attr,
+				char *buf)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	struct w83791d_data *data = w83791d_update_device(dev);
+	return sprintf(buf, "%u\n", DIV_FROM_REG(data->fan_div[nr]));
+}
+
+/* Note: we save and restore the fan minimum here, because its value is
+   determined in part by the fan divisor.  This follows the principle of
+   least suprise; the user doesn't expect the fan minimum to change just
+   because the divisor changed. */
+static ssize_t store_fan_div(struct device *dev, struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	int nr = sensor_attr->index;
+	unsigned long min;
+	u8 tmp_fan_div;
+	u8 fan_div_reg;
+	int indx = 0;
+	u8 keep_mask = 0;
+	u8 new_shift = 0;
+
+	/* Save fan_min */
+	min = FAN_FROM_REG(data->fan_min[nr], DIV_FROM_REG(data->fan_div[nr]));
+
+	mutex_lock(&data->update_lock);
+	data->fan_div[nr] = div_to_reg(nr, simple_strtoul(buf, NULL, 10));
+
+	switch (nr) {
+	case 0:
+		indx = 0;
+		keep_mask = 0xcf;
+		new_shift = 4;
+		break;
+	case 1:
+		indx = 0;
+		keep_mask = 0x3f;
+		new_shift = 6;
+		break;
+	case 2:
+		indx = 1;
+		keep_mask = 0x3f;
+		new_shift = 6;
+		break;
+	case 3:
+		indx = 2;
+		keep_mask = 0xf8;
+		new_shift = 0;
+		break;
+	case 4:
+		indx = 2;
+		keep_mask = 0x8f;
+		new_shift = 4;
+		break;
+#ifdef DEBUG
+	default:
+		dev_warn(dev, "store_fan_div: Unexpected nr seen: %d\n", nr);
+		count = -EINVAL;
+		goto err_exit;
+#endif
+	}
+
+	fan_div_reg = w83791d_read(client, W83791D_REG_FAN_DIV[indx])
+			& keep_mask;
+	tmp_fan_div = (data->fan_div[nr] << new_shift) & ~keep_mask;
+
+	w83791d_write(client, W83791D_REG_FAN_DIV[indx],
+				fan_div_reg | tmp_fan_div);
+
+	/* Restore fan_min */
+	data->fan_min[nr] = fan_to_reg(min, DIV_FROM_REG(data->fan_div[nr]));
+	w83791d_write(client, W83791D_REG_FAN_MIN[nr], data->fan_min[nr]);
+
+#ifdef DEBUG
+err_exit:
+#endif
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static struct sensor_device_attribute sda_fan_input[] = {
+	SENSOR_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 0),
+	SENSOR_ATTR(fan2_input, S_IRUGO, show_fan, NULL, 1),
+	SENSOR_ATTR(fan3_input, S_IRUGO, show_fan, NULL, 2),
+	SENSOR_ATTR(fan4_input, S_IRUGO, show_fan, NULL, 3),
+	SENSOR_ATTR(fan5_input, S_IRUGO, show_fan, NULL, 4),
+};
+
+static struct sensor_device_attribute sda_fan_min[] = {
+	SENSOR_ATTR(fan1_min, S_IWUSR | S_IRUGO,
+			show_fan_min, store_fan_min, 0),
+	SENSOR_ATTR(fan2_min, S_IWUSR | S_IRUGO,
+			show_fan_min, store_fan_min, 1),
+	SENSOR_ATTR(fan3_min, S_IWUSR | S_IRUGO,
+			show_fan_min, store_fan_min, 2),
+	SENSOR_ATTR(fan4_min, S_IWUSR | S_IRUGO,
+			show_fan_min, store_fan_min, 3),
+	SENSOR_ATTR(fan5_min, S_IWUSR | S_IRUGO,
+			show_fan_min, store_fan_min, 4),
+};
+
+static struct sensor_device_attribute sda_fan_div[] = {
+	SENSOR_ATTR(fan1_div, S_IWUSR | S_IRUGO,
+			show_fan_div, store_fan_div, 0),
+	SENSOR_ATTR(fan2_div, S_IWUSR | S_IRUGO,
+			show_fan_div, store_fan_div, 1),
+	SENSOR_ATTR(fan3_div, S_IWUSR | S_IRUGO,
+			show_fan_div, store_fan_div, 2),
+	SENSOR_ATTR(fan4_div, S_IWUSR | S_IRUGO,
+			show_fan_div, store_fan_div, 3),
+	SENSOR_ATTR(fan5_div, S_IWUSR | S_IRUGO,
+			show_fan_div, store_fan_div, 4),
+};
+
+/* read/write the temperature1, includes measured value and limits */
+static ssize_t show_temp1(struct device *dev, struct device_attribute *devattr,
+				char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct w83791d_data *data = w83791d_update_device(dev);
+	return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp1[attr->index]));
+}
+
+static ssize_t store_temp1(struct device *dev, struct device_attribute *devattr,
+				const char *buf, size_t count)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	long val = simple_strtol(buf, NULL, 10);
+	int nr = attr->index;
+
+	mutex_lock(&data->update_lock);
+	data->temp1[nr] = TEMP1_TO_REG(val);
+	w83791d_write(client, W83791D_REG_TEMP1[nr], data->temp1[nr]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+/* read/write temperature2-3, includes measured value and limits */
+static ssize_t show_temp23(struct device *dev, struct device_attribute *devattr,
+				char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct w83791d_data *data = w83791d_update_device(dev);
+	int nr = attr->nr;
+	int index = attr->index;
+	return sprintf(buf, "%d\n", TEMP23_FROM_REG(data->temp_add[nr][index]));
+}
+
+static ssize_t store_temp23(struct device *dev,
+				struct device_attribute *devattr,
+				const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	long val = simple_strtol(buf, NULL, 10);
+	int nr = attr->nr;
+	int index = attr->index;
+
+	mutex_lock(&data->update_lock);
+	data->temp_add[nr][index] = TEMP23_TO_REG(val);
+	w83791d_write(client, W83791D_REG_TEMP_ADD[nr][index * 2],
+				data->temp_add[nr][index] >> 8);
+	w83791d_write(client, W83791D_REG_TEMP_ADD[nr][index * 2 + 1],
+				data->temp_add[nr][index] & 0x80);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static struct sensor_device_attribute_2 sda_temp_input[] = {
+	SENSOR_ATTR_2(temp1_input, S_IRUGO, show_temp1, NULL, 0, 0),
+	SENSOR_ATTR_2(temp2_input, S_IRUGO, show_temp23, NULL, 0, 0),
+	SENSOR_ATTR_2(temp3_input, S_IRUGO, show_temp23, NULL, 1, 0),
+};
+
+static struct sensor_device_attribute_2 sda_temp_max[] = {
+	SENSOR_ATTR_2(temp1_max, S_IRUGO | S_IWUSR,
+			show_temp1, store_temp1, 0, 1),
+	SENSOR_ATTR_2(temp2_max, S_IRUGO | S_IWUSR,
+			show_temp23, store_temp23, 0, 1),
+	SENSOR_ATTR_2(temp3_max, S_IRUGO | S_IWUSR,
+			show_temp23, store_temp23, 1, 1),
+};
+
+static struct sensor_device_attribute_2 sda_temp_max_hyst[] = {
+	SENSOR_ATTR_2(temp1_max_hyst, S_IRUGO | S_IWUSR,
+			show_temp1, store_temp1, 0, 2),
+	SENSOR_ATTR_2(temp2_max_hyst, S_IRUGO | S_IWUSR,
+			show_temp23, store_temp23, 0, 2),
+	SENSOR_ATTR_2(temp3_max_hyst, S_IRUGO | S_IWUSR,
+			show_temp23, store_temp23, 1, 2),
+};
+
+
+/* get reatime status of all sensors items: voltage, temp, fan */
+static ssize_t show_alarms_reg(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct w83791d_data *data = w83791d_update_device(dev);
+	return sprintf(buf, "%u\n", data->alarms);
+}
+
+static DEVICE_ATTR(alarms, S_IRUGO, show_alarms_reg, NULL);
+
+/* Beep control */
+
+#define GLOBAL_BEEP_ENABLE_SHIFT	15
+#define GLOBAL_BEEP_ENABLE_MASK		(1 << GLOBAL_BEEP_ENABLE_SHIFT)
+
+static ssize_t show_beep_enable(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct w83791d_data *data = w83791d_update_device(dev);
+	return sprintf(buf, "%d\n", data->beep_enable);
+}
+
+static ssize_t show_beep_mask(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct w83791d_data *data = w83791d_update_device(dev);
+	return sprintf(buf, "%d\n", BEEP_MASK_FROM_REG(data->beep_mask));
+}
+
+
+static ssize_t store_beep_mask(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	long val = simple_strtol(buf, NULL, 10);
+	int i;
+
+	mutex_lock(&data->update_lock);
+
+	/* The beep_enable state overrides any enabling request from
+	   the masks */
+	data->beep_mask = BEEP_MASK_TO_REG(val) & ~GLOBAL_BEEP_ENABLE_MASK;
+	data->beep_mask |= (data->beep_enable << GLOBAL_BEEP_ENABLE_SHIFT);
+
+	val = data->beep_mask;
+
+	for (i = 0; i < 3; i++) {
+		w83791d_write(client, W83791D_REG_BEEP_CTRL[i], (val & 0xff));
+		val >>= 8;
+	}
+
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static ssize_t store_beep_enable(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+
+	data->beep_enable = val ? 1 : 0;
+
+	/* Keep the full mask value in sync with the current enable */
+	data->beep_mask &= ~GLOBAL_BEEP_ENABLE_MASK;
+	data->beep_mask |= (data->beep_enable << GLOBAL_BEEP_ENABLE_SHIFT);
+
+	/* The global control is in the second beep control register
+	   so only need to update that register */
+	val = (data->beep_mask >> 8) & 0xff;
+
+	w83791d_write(client, W83791D_REG_BEEP_CTRL[1], val);
+
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+static struct sensor_device_attribute sda_beep_ctrl[] = {
+	SENSOR_ATTR(beep_enable, S_IRUGO | S_IWUSR,
+			show_beep_enable, store_beep_enable, 0),
+	SENSOR_ATTR(beep_mask, S_IRUGO | S_IWUSR,
+			show_beep_mask, store_beep_mask, 1)
+};
+
+/* cpu voltage regulation information */
+static ssize_t show_vid_reg(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct w83791d_data *data = w83791d_update_device(dev);
+	return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
+}
+
+static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid_reg, NULL);
+
+static ssize_t show_vrm_reg(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct w83791d_data *data = w83791d_update_device(dev);
+	return sprintf(buf, "%d\n", data->vrm);
+}
+
+static ssize_t store_vrm_reg(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	unsigned long val = simple_strtoul(buf, NULL, 10);
+
+	/* No lock needed as vrm is internal to the driver
+	   (not read from a chip register) and so is not
+	   updated in w83791d_update_device() */
+	data->vrm = val;
+
+	return count;
+}
+
+static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm_reg, store_vrm_reg);
+
+/* This function is called when:
+     * w83791d_driver is inserted (when this module is loaded), for each
+       available adapter
+     * when a new adapter is inserted (and w83791d_driver is still present) */
+static int w83791d_attach_adapter(struct i2c_adapter *adapter)
+{
+	if (!(adapter->class & I2C_CLASS_HWMON))
+		return 0;
+	return i2c_probe(adapter, &addr_data, w83791d_detect);
+}
+
+
+static int w83791d_create_subclient(struct i2c_adapter *adapter,
+				struct i2c_client *client, int addr,
+				struct i2c_client **sub_cli)
+{
+	int err;
+	struct i2c_client *sub_client;
+
+	(*sub_cli) = sub_client =
+			kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
+	if (!(sub_client)) {
+		return -ENOMEM;
+	}
+	sub_client->addr = 0x48 + addr;
+	i2c_set_clientdata(sub_client, NULL);
+	sub_client->adapter = adapter;
+	sub_client->driver = &w83791d_driver;
+	strlcpy(sub_client->name, "w83791d subclient", I2C_NAME_SIZE);
+	if ((err = i2c_attach_client(sub_client))) {
+		dev_err(&client->dev, "subclient registration "
+			"at address 0x%x failed\n", sub_client->addr);
+		kfree(sub_client);
+		return err;
+	}
+	return 0;
+}
+
+
+static int w83791d_detect_subclients(struct i2c_adapter *adapter, int address,
+				int kind, struct i2c_client *client)
+{
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	int i, id, err;
+	u8 val;
+
+	id = i2c_adapter_id(adapter);
+	if (force_subclients[0] == id && force_subclients[1] == address) {
+		for (i = 2; i <= 3; i++) {
+			if (force_subclients[i] < 0x48 ||
+			    force_subclients[i] > 0x4f) {
+				dev_err(&client->dev,
+					"invalid subclient "
+					"address %d; must be 0x48-0x4f\n",
+					force_subclients[i]);
+				err = -ENODEV;
+				goto error_sc_0;
+			}
+		}
+		w83791d_write(client, W83791D_REG_I2C_SUBADDR,
+					(force_subclients[2] & 0x07) |
+					((force_subclients[3] & 0x07) << 4));
+	}
+
+	val = w83791d_read(client, W83791D_REG_I2C_SUBADDR);
+	if (!(val & 0x08)) {
+		err = w83791d_create_subclient(adapter, client,
+						val & 0x7, &data->lm75[0]);
+		if (err < 0)
+			goto error_sc_0;
+	}
+	if (!(val & 0x80)) {
+		if ((data->lm75[0] != NULL) &&
+				((val & 0x7) == ((val >> 4) & 0x7))) {
+			dev_err(&client->dev,
+				"duplicate addresses 0x%x, "
+				"use force_subclient\n",
+				data->lm75[0]->addr);
+			err = -ENODEV;
+			goto error_sc_1;
+		}
+		err = w83791d_create_subclient(adapter, client,
+					(val >> 4) & 0x7, &data->lm75[1]);
+		if (err < 0)
+			goto error_sc_1;
+	}
+
+	return 0;
+
+/* Undo inits in case of errors */
+
+error_sc_1:
+	if (data->lm75[0] != NULL) {
+		i2c_detach_client(data->lm75[0]);
+		kfree(data->lm75[0]);
+	}
+error_sc_0:
+	return err;
+}
+
+
+static int w83791d_detect(struct i2c_adapter *adapter, int address, int kind)
+{
+	struct i2c_client *client;
+	struct device *dev;
+	struct w83791d_data *data;
+	int i, val1, val2;
+	int err = 0;
+	const char *client_name = "";
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+		goto error0;
+	}
+
+	/* OK. For now, we presume we have a valid client. We now create the
+	   client structure, even though we cannot fill it completely yet.
+	   But it allows us to access w83791d_{read,write}_value. */
+	if (!(data = kzalloc(sizeof(struct w83791d_data), GFP_KERNEL))) {
+		err = -ENOMEM;
+		goto error0;
+	}
+
+	client = &data->client;
+	dev = &client->dev;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &w83791d_driver;
+	mutex_init(&data->update_lock);
+
+	/* Now, we do the remaining detection. */
+
+	/* The w83791d may be stuck in some other bank than bank 0. This may
+	   make reading other information impossible. Specify a force=...
+	   parameter, and the Winbond will be reset to the right bank. */
+	if (kind < 0) {
+		if (w83791d_read(client, W83791D_REG_CONFIG) & 0x80) {
+			dev_dbg(dev, "Detection failed at step 1\n");
+			goto error1;
+		}
+		val1 = w83791d_read(client, W83791D_REG_BANK);
+		val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
+		/* Check for Winbond ID if in bank 0 */
+		if (!(val1 & 0x07)) {
+			/* yes it is Bank0 */
+			if (((!(val1 & 0x80)) && (val2 != 0xa3)) ||
+			    ((val1 & 0x80) && (val2 != 0x5c))) {
+				dev_dbg(dev, "Detection failed at step 2\n");
+				goto error1;
+			}
+		}
+		/* If Winbond chip, address of chip and W83791D_REG_I2C_ADDR
+		   should match */
+		if (w83791d_read(client, W83791D_REG_I2C_ADDR) != address) {
+			dev_dbg(dev, "Detection failed at step 3\n");
+			goto error1;
+		}
+	}
+
+	/* We either have a force parameter or we have reason to
+	   believe it is a Winbond chip. Either way, we want bank 0 and
+	   Vendor ID high byte */
+	val1 = w83791d_read(client, W83791D_REG_BANK) & 0x78;
+	w83791d_write(client, W83791D_REG_BANK, val1 | 0x80);
+
+	/* Verify it is a Winbond w83791d */
+	if (kind <= 0) {
+		/* get vendor ID */
+		val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
+		if (val2 != 0x5c) {	/* the vendor is NOT Winbond */
+			dev_dbg(dev, "Detection failed at step 4\n");
+			goto error1;
+		}
+		val1 = w83791d_read(client, W83791D_REG_WCHIPID);
+		if (val1 == 0x71) {
+			kind = w83791d;
+		} else {
+			if (kind == 0)
+				dev_warn(dev,
+					"w83791d: Ignoring 'force' parameter "
+					"for unknown chip at adapter %d, "
+					"address 0x%02x\n",
+					i2c_adapter_id(adapter), address);
+			goto error1;
+		}
+	}
+
+	if (kind == w83791d) {
+		client_name = "w83791d";
+	} else {
+		dev_err(dev, "w83791d: Internal error: unknown kind (%d)?!?",
+			kind);
+		goto error1;
+	}
+
+#ifdef DEBUG
+	val1 = w83791d_read(client, W83791D_REG_DID_VID4);
+	dev_dbg(dev, "Device ID version: %d.%d (0x%02x)\n",
+			(val1 >> 5) & 0x07, (val1 >> 1) & 0x0f, val1);
+#endif
+
+	/* Fill in the remaining client fields and put into the global list */
+	strlcpy(client->name, client_name, I2C_NAME_SIZE);
+
+	/* Tell the I2C layer a new client has arrived */
+	if ((err = i2c_attach_client(client)))
+		goto error1;
+
+	if ((err = w83791d_detect_subclients(adapter, address, kind, client)))
+		goto error2;
+
+	/* Initialize the chip */
+	w83791d_init_client(client);
+
+	/* If the fan_div is changed, make sure there is a rational
+	   fan_min in place */
+	for (i = 0; i < NUMBER_OF_FANIN; i++) {
+		data->fan_min[i] = w83791d_read(client, W83791D_REG_FAN_MIN[i]);
+	}
+
+	/* Register sysfs hooks */
+	data->class_dev = hwmon_device_register(dev);
+	if (IS_ERR(data->class_dev)) {
+		err = PTR_ERR(data->class_dev);
+		goto error3;
+	}
+
+	for (i = 0; i < NUMBER_OF_VIN; i++) {
+		device_create_file(dev, &sda_in_input[i].dev_attr);
+		device_create_file(dev, &sda_in_min[i].dev_attr);
+		device_create_file(dev, &sda_in_max[i].dev_attr);
+	}
+
+	for (i = 0; i < NUMBER_OF_FANIN; i++) {
+		device_create_file(dev, &sda_fan_input[i].dev_attr);
+		device_create_file(dev, &sda_fan_div[i].dev_attr);
+		device_create_file(dev, &sda_fan_min[i].dev_attr);
+	}
+
+	for (i = 0; i < NUMBER_OF_TEMPIN; i++) {
+		device_create_file(dev, &sda_temp_input[i].dev_attr);
+		device_create_file(dev, &sda_temp_max[i].dev_attr);
+		device_create_file(dev, &sda_temp_max_hyst[i].dev_attr);
+	}
+
+	device_create_file(dev, &dev_attr_alarms);
+
+	for (i = 0; i < ARRAY_SIZE(sda_beep_ctrl); i++) {
+		device_create_file(dev, &sda_beep_ctrl[i].dev_attr);
+	}
+
+	device_create_file(dev, &dev_attr_cpu0_vid);
+	device_create_file(dev, &dev_attr_vrm);
+
+	return 0;
+
+error3:
+	if (data->lm75[0] != NULL) {
+		i2c_detach_client(data->lm75[0]);
+		kfree(data->lm75[0]);
+	}
+	if (data->lm75[1] != NULL) {
+		i2c_detach_client(data->lm75[1]);
+		kfree(data->lm75[1]);
+	}
+error2:
+	i2c_detach_client(client);
+error1:
+	kfree(data);
+error0:
+	return err;
+}
+
+static int w83791d_detach_client(struct i2c_client *client)
+{
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	int err;
+
+	/* main client */
+	if (data)
+		hwmon_device_unregister(data->class_dev);
+
+	if ((err = i2c_detach_client(client)))
+		return err;
+
+	/* main client */
+	if (data)
+		kfree(data);
+	/* subclient */
+	else
+		kfree(client);
+
+	return 0;
+}
+
+static void w83791d_init_client(struct i2c_client *client)
+{
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	u8 tmp;
+	u8 old_beep;
+
+	/* The difference between reset and init is that reset
+	   does a hard reset of the chip via index 0x40, bit 7,
+	   but init simply forces certain registers to have "sane"
+	   values. The hope is that the BIOS has done the right
+	   thing (which is why the default is reset=0, init=0),
+	   but if not, reset is the hard hammer and init
+	   is the soft mallet both of which are trying to whack
+	   things into place...
+	   NOTE: The data sheet makes a distinction between
+	   "power on defaults" and "reset by MR". As far as I can tell,
+	   the hard reset puts everything into a power-on state so I'm
+	   not sure what "reset by MR" means or how it can happen.
+	   */
+	if (reset || init) {
+		/* keep some BIOS settings when we... */
+		old_beep = w83791d_read(client, W83791D_REG_BEEP_CONFIG);
+
+		if (reset) {
+			/* ... reset the chip and ... */
+			w83791d_write(client, W83791D_REG_CONFIG, 0x80);
+		}
+
+		/* ... disable power-on abnormal beep */
+		w83791d_write(client, W83791D_REG_BEEP_CONFIG, old_beep | 0x80);
+
+		/* disable the global beep (not done by hard reset) */
+		tmp = w83791d_read(client, W83791D_REG_BEEP_CTRL[1]);
+		w83791d_write(client, W83791D_REG_BEEP_CTRL[1], tmp & 0xef);
+
+		if (init) {
+			/* Make sure monitoring is turned on for add-ons */
+			tmp = w83791d_read(client, W83791D_REG_TEMP2_CONFIG);
+			if (tmp & 1) {
+				w83791d_write(client, W83791D_REG_TEMP2_CONFIG,
+					tmp & 0xfe);
+			}
+
+			tmp = w83791d_read(client, W83791D_REG_TEMP3_CONFIG);
+			if (tmp & 1) {
+				w83791d_write(client, W83791D_REG_TEMP3_CONFIG,
+					tmp & 0xfe);
+			}
+
+			/* Start monitoring */
+			tmp = w83791d_read(client, W83791D_REG_CONFIG) & 0xf7;
+			w83791d_write(client, W83791D_REG_CONFIG, tmp | 0x01);
+		}
+	}
+
+	data->vrm = vid_which_vrm();
+}
+
+static struct w83791d_data *w83791d_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct w83791d_data *data = i2c_get_clientdata(client);
+	int i, j;
+	u8 reg_array_tmp[3];
+
+	mutex_lock(&data->update_lock);
+
+	if (time_after(jiffies, data->last_updated + (HZ * 3))
+			|| !data->valid) {
+		dev_dbg(dev, "Starting w83791d device update\n");
+
+		/* Update the voltages measured value and limits */
+		for (i = 0; i < NUMBER_OF_VIN; i++) {
+			data->in[i] = w83791d_read(client,
+						W83791D_REG_IN[i]);
+			data->in_max[i] = w83791d_read(client,
+						W83791D_REG_IN_MAX[i]);
+			data->in_min[i] = w83791d_read(client,
+						W83791D_REG_IN_MIN[i]);
+		}
+
+		/* Update the fan counts and limits */
+		for (i = 0; i < NUMBER_OF_FANIN; i++) {
+			/* Update the Fan measured value and limits */
+			data->fan[i] = w83791d_read(client,
+						W83791D_REG_FAN[i]);
+			data->fan_min[i] = w83791d_read(client,
+						W83791D_REG_FAN_MIN[i]);
+		}
+
+		/* Update the fan divisor */
+		for (i = 0; i < 3; i++) {
+			reg_array_tmp[i] = w83791d_read(client,
+						W83791D_REG_FAN_DIV[i]);
+		}
+		data->fan_div[0] = (reg_array_tmp[0] >> 4) & 0x03;
+		data->fan_div[1] = (reg_array_tmp[0] >> 6) & 0x03;
+		data->fan_div[2] = (reg_array_tmp[1] >> 6) & 0x03;
+		data->fan_div[3] = reg_array_tmp[2] & 0x07;
+		data->fan_div[4] = (reg_array_tmp[2] >> 4) & 0x07;
+
+		/* Update the first temperature sensor */
+		for (i = 0; i < 3; i++) {
+			data->temp1[i] = w83791d_read(client,
+						W83791D_REG_TEMP1[i]);
+		}
+
+		/* Update the rest of the temperature sensors */
+		for (i = 0; i < 2; i++) {
+			for (j = 0; j < 3; j++) {
+				data->temp_add[i][j] =
+					(w83791d_read(client,
+					W83791D_REG_TEMP_ADD[i][j * 2]) << 8) |
+					w83791d_read(client,
+					W83791D_REG_TEMP_ADD[i][j * 2 + 1]);
+			}
+		}
+
+		/* Update the realtime status */
+		data->alarms =
+			w83791d_read(client, W83791D_REG_ALARM1) +
+			(w83791d_read(client, W83791D_REG_ALARM2) << 8) +
+			(w83791d_read(client, W83791D_REG_ALARM3) << 16);
+
+		/* Update the beep configuration information */
+		data->beep_mask =
+			w83791d_read(client, W83791D_REG_BEEP_CTRL[0]) +
+			(w83791d_read(client, W83791D_REG_BEEP_CTRL[1]) << 8) +
+			(w83791d_read(client, W83791D_REG_BEEP_CTRL[2]) << 16);
+
+		data->beep_enable =
+			(data->beep_mask >> GLOBAL_BEEP_ENABLE_SHIFT) & 0x01;
+
+		/* Update the cpu voltage information */
+		i = w83791d_read(client, W83791D_REG_VID_FANDIV);
+		data->vid = i & 0x0f;
+		data->vid |= (w83791d_read(client, W83791D_REG_DID_VID4) & 0x01)
+				<< 4;
+
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+
+	mutex_unlock(&data->update_lock);
+
+#ifdef DEBUG
+	w83791d_print_debug(data, dev);
+#endif
+
+	return data;
+}
+
+#ifdef DEBUG
+static void w83791d_print_debug(struct w83791d_data *data, struct device *dev)
+{
+	int i = 0, j = 0;
+
+	dev_dbg(dev, "======Start of w83791d debug values======\n");
+	dev_dbg(dev, "%d set of Voltages: ===>\n", NUMBER_OF_VIN);
+	for (i = 0; i < NUMBER_OF_VIN; i++) {
+		dev_dbg(dev, "vin[%d] is:     0x%02x\n", i, data->in[i]);
+		dev_dbg(dev, "vin[%d] min is: 0x%02x\n", i, data->in_min[i]);
+		dev_dbg(dev, "vin[%d] max is: 0x%02x\n", i, data->in_max[i]);
+	}
+	dev_dbg(dev, "%d set of Fan Counts/Divisors: ===>\n", NUMBER_OF_FANIN);
+	for (i = 0; i < NUMBER_OF_FANIN; i++) {
+		dev_dbg(dev, "fan[%d] is:     0x%02x\n", i, data->fan[i]);
+		dev_dbg(dev, "fan[%d] min is: 0x%02x\n", i, data->fan_min[i]);
+		dev_dbg(dev, "fan_div[%d] is: 0x%02x\n", i, data->fan_div[i]);
+	}
+
+	/* temperature math is signed, but only print out the
+	   bits that matter */
+	dev_dbg(dev, "%d set of Temperatures: ===>\n", NUMBER_OF_TEMPIN);
+	for (i = 0; i < 3; i++) {
+		dev_dbg(dev, "temp1[%d] is: 0x%02x\n", i, (u8) data->temp1[i]);
+	}
+	for (i = 0; i < 2; i++) {
+		for (j = 0; j < 3; j++) {
+			dev_dbg(dev, "temp_add[%d][%d] is: 0x%04x\n", i, j,
+				(u16) data->temp_add[i][j]);
+		}
+	}
+
+	dev_dbg(dev, "Misc Information: ===>\n");
+	dev_dbg(dev, "alarm is:     0x%08x\n", data->alarms);
+	dev_dbg(dev, "beep_mask is: 0x%08x\n", data->beep_mask);
+	dev_dbg(dev, "beep_enable is: %d\n", data->beep_enable);
+	dev_dbg(dev, "vid is: 0x%02x\n", data->vid);
+	dev_dbg(dev, "vrm is: 0x%02x\n", data->vrm);
+	dev_dbg(dev, "=======End of w83791d debug values========\n");
+	dev_dbg(dev, "\n");
+}
+#endif
+
+static int __init sensors_w83791d_init(void)
+{
+	return i2c_add_driver(&w83791d_driver);
+}
+
+static void __exit sensors_w83791d_exit(void)
+{
+	i2c_del_driver(&w83791d_driver);
+}
+
+MODULE_AUTHOR("Charles Spirakis <bezaur@gmail.com>");
+MODULE_DESCRIPTION("W83791D driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_w83791d_init);
+module_exit(sensors_w83791d_exit);
diff --git a/drivers/hwmon/w83792d.c b/drivers/hwmon/w83792d.c
index 958602e2841..4ef884c216e 100644
--- a/drivers/hwmon/w83792d.c
+++ b/drivers/hwmon/w83792d.c
@@ -250,8 +250,6 @@ FAN_TO_REG(long rpm, int div)
 			: (val)) / 1000, 0, 0xff))
 #define TEMP_ADD_TO_REG_LOW(val)	((val%1000) ? 0x80 : 0x00)
 
-#define PWM_FROM_REG(val)		(val)
-#define PWM_TO_REG(val)			(SENSORS_LIMIT((val),0,255))
 #define DIV_FROM_REG(val)		(1 << (val))
 
 static inline u8
@@ -291,7 +289,6 @@ struct w83792d_data {
 	u8 pwm[7];		/* We only consider the first 3 set of pwm,
 				   although 792 chip has 7 set of pwm. */
 	u8 pwmenable[3];
-	u8 pwm_mode[7];		/* indicates PWM or DC mode: 1->PWM; 0->DC */
 	u32 alarms;		/* realtime status register encoding,combined */
 	u8 chassis;		/* Chassis status */
 	u8 chassis_clear;	/* CLR_CHS, clear chassis intrusion detection */
@@ -375,8 +372,10 @@ static ssize_t store_in_##reg (struct device *dev, \
 	u32 val; \
 	 \
 	val = simple_strtoul(buf, NULL, 10); \
+	mutex_lock(&data->update_lock); \
 	data->in_##reg[nr] = SENSORS_LIMIT(IN_TO_REG(nr, val)/4, 0, 255); \
 	w83792d_write_value(client, W83792D_REG_IN_##REG[nr], data->in_##reg[nr]); \
+	mutex_unlock(&data->update_lock); \
 	 \
 	return count; \
 }
@@ -443,9 +442,11 @@ store_fan_min(struct device *dev, struct device_attribute *attr,
 	u32 val;
 
 	val = simple_strtoul(buf, NULL, 10);
+	mutex_lock(&data->update_lock);
 	data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
 	w83792d_write_value(client, W83792D_REG_FAN_MIN[nr],
 				data->fan_min[nr]);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -478,6 +479,7 @@ store_fan_div(struct device *dev, struct device_attribute *attr,
 	u8 tmp_fan_div;
 
 	/* Save fan_min */
+	mutex_lock(&data->update_lock);
 	min = FAN_FROM_REG(data->fan_min[nr],
 			   DIV_FROM_REG(data->fan_div[nr]));
 
@@ -493,6 +495,7 @@ store_fan_div(struct device *dev, struct device_attribute *attr,
 	/* Restore fan_min */
 	data->fan_min[nr] = FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
 	w83792d_write_value(client, W83792D_REG_FAN_MIN[nr], data->fan_min[nr]);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -547,10 +550,11 @@ static ssize_t store_temp1(struct device *dev, struct device_attribute *attr,
 	s32 val;
 
 	val = simple_strtol(buf, NULL, 10);
-
+	mutex_lock(&data->update_lock);
 	data->temp1[nr] = TEMP1_TO_REG(val);
 	w83792d_write_value(client, W83792D_REG_TEMP1[nr],
 		data->temp1[nr]);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -580,13 +584,14 @@ static ssize_t store_temp23(struct device *dev, struct device_attribute *attr,
 	s32 val;
 
 	val = simple_strtol(buf, NULL, 10);
-
+	mutex_lock(&data->update_lock);
 	data->temp_add[nr][index] = TEMP_ADD_TO_REG_HIGH(val);
 	data->temp_add[nr][index+1] = TEMP_ADD_TO_REG_LOW(val);
 	w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index],
 		data->temp_add[nr][index]);
 	w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index+1],
 		data->temp_add[nr][index+1]);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -627,7 +632,7 @@ show_pwm(struct device *dev, struct device_attribute *attr,
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	struct w83792d_data *data = w83792d_update_device(dev);
-	return sprintf(buf, "%ld\n", (long) PWM_FROM_REG(data->pwm[nr-1]));
+	return sprintf(buf, "%d\n", (data->pwm[nr] & 0x0f) << 4);
 }
 
 static ssize_t
@@ -659,14 +664,16 @@ store_pwm(struct device *dev, struct device_attribute *attr,
 		const char *buf, size_t count)
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
-	int nr = sensor_attr->index - 1;
+	int nr = sensor_attr->index;
 	struct i2c_client *client = to_i2c_client(dev);
 	struct w83792d_data *data = i2c_get_clientdata(client);
-	u32 val;
+	u8 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 0, 255) >> 4;
 
-	val = simple_strtoul(buf, NULL, 10);
-	data->pwm[nr] = PWM_TO_REG(val);
+	mutex_lock(&data->update_lock);
+	val |= w83792d_read_value(client, W83792D_REG_PWM[nr]) & 0xf0;
+	data->pwm[nr] = val;
 	w83792d_write_value(client, W83792D_REG_PWM[nr], data->pwm[nr]);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -683,6 +690,10 @@ store_pwmenable(struct device *dev, struct device_attribute *attr,
 	u8 fan_cfg_tmp, cfg1_tmp, cfg2_tmp, cfg3_tmp, cfg4_tmp;
 
 	val = simple_strtoul(buf, NULL, 10);
+	if (val < 1 || val > 3)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
 	switch (val) {
 	case 1:
 		data->pwmenable[nr] = 0; /* manual mode */
@@ -693,8 +704,6 @@ store_pwmenable(struct device *dev, struct device_attribute *attr,
 	case 3:
 		data->pwmenable[nr] = 1; /* thermal cruise/Smart Fan I */
 		break;
-	default:
-		return -EINVAL;
 	}
 	cfg1_tmp = data->pwmenable[0];
 	cfg2_tmp = (data->pwmenable[1]) << 2;
@@ -702,14 +711,15 @@ store_pwmenable(struct device *dev, struct device_attribute *attr,
 	cfg4_tmp = w83792d_read_value(client,W83792D_REG_FAN_CFG) & 0xc0;
 	fan_cfg_tmp = ((cfg4_tmp | cfg3_tmp) | cfg2_tmp) | cfg1_tmp;
 	w83792d_write_value(client, W83792D_REG_FAN_CFG, fan_cfg_tmp);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
 
 static struct sensor_device_attribute sda_pwm[] = {
-	SENSOR_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 1),
-	SENSOR_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 2),
-	SENSOR_ATTR(pwm3, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 3),
+	SENSOR_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 0),
+	SENSOR_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 1),
+	SENSOR_ATTR(pwm3, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 2),
 };
 static struct sensor_device_attribute sda_pwm_enable[] = {
 	SENSOR_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
@@ -728,7 +738,7 @@ show_pwm_mode(struct device *dev, struct device_attribute *attr,
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 	int nr = sensor_attr->index;
 	struct w83792d_data *data = w83792d_update_device(dev);
-	return sprintf(buf, "%d\n", data->pwm_mode[nr-1]);
+	return sprintf(buf, "%d\n", data->pwm[nr] >> 7);
 }
 
 static ssize_t
@@ -736,29 +746,35 @@ store_pwm_mode(struct device *dev, struct device_attribute *attr,
 			const char *buf, size_t count)
 {
 	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
-	int nr = sensor_attr->index - 1;
+	int nr = sensor_attr->index;
 	struct i2c_client *client = to_i2c_client(dev);
 	struct w83792d_data *data = i2c_get_clientdata(client);
 	u32 val;
-	u8 pwm_mode_mask = 0;
 
 	val = simple_strtoul(buf, NULL, 10);
-	data->pwm_mode[nr] = SENSORS_LIMIT(val, 0, 1);
-	pwm_mode_mask = w83792d_read_value(client,
-		W83792D_REG_PWM[nr]) & 0x7f;
-	w83792d_write_value(client, W83792D_REG_PWM[nr],
-		((data->pwm_mode[nr]) << 7) | pwm_mode_mask);
+	if (val != 0 && val != 1)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	data->pwm[nr] = w83792d_read_value(client, W83792D_REG_PWM[nr]);
+	if (val) {			/* PWM mode */
+		data->pwm[nr] |= 0x80;
+	} else {			/* DC mode */
+		data->pwm[nr] &= 0x7f;
+	}
+	w83792d_write_value(client, W83792D_REG_PWM[nr], data->pwm[nr]);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
 
 static struct sensor_device_attribute sda_pwm_mode[] = {
 	SENSOR_ATTR(pwm1_mode, S_IWUSR | S_IRUGO,
-		    show_pwm_mode, store_pwm_mode, 1),
+		    show_pwm_mode, store_pwm_mode, 0),
 	SENSOR_ATTR(pwm2_mode, S_IWUSR | S_IRUGO,
-		    show_pwm_mode, store_pwm_mode, 2),
+		    show_pwm_mode, store_pwm_mode, 1),
 	SENSOR_ATTR(pwm3_mode, S_IWUSR | S_IRUGO,
-		    show_pwm_mode, store_pwm_mode, 3),
+		    show_pwm_mode, store_pwm_mode, 2),
 };
 
 
@@ -789,12 +805,13 @@ store_chassis_clear(struct device *dev, struct device_attribute *attr,
 	u8 temp1 = 0, temp2 = 0;
 
 	val = simple_strtoul(buf, NULL, 10);
-
+	mutex_lock(&data->update_lock);
 	data->chassis_clear = SENSORS_LIMIT(val, 0 ,1);
 	temp1 = ((data->chassis_clear) << 7) & 0x80;
 	temp2 = w83792d_read_value(client,
 		W83792D_REG_CHASSIS_CLR) & 0x7f;
 	w83792d_write_value(client, W83792D_REG_CHASSIS_CLR, temp1 | temp2);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -827,10 +844,12 @@ store_thermal_cruise(struct device *dev, struct device_attribute *attr,
 	val = simple_strtoul(buf, NULL, 10);
 	target_tmp = val;
 	target_tmp = target_tmp & 0x7f;
+	mutex_lock(&data->update_lock);
 	target_mask = w83792d_read_value(client, W83792D_REG_THERMAL[nr]) & 0x80;
 	data->thermal_cruise[nr] = SENSORS_LIMIT(target_tmp, 0, 255);
 	w83792d_write_value(client, W83792D_REG_THERMAL[nr],
 		(data->thermal_cruise[nr]) | target_mask);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -867,6 +886,7 @@ store_tolerance(struct device *dev, struct device_attribute *attr,
 	u8 tol_tmp, tol_mask;
 
 	val = simple_strtoul(buf, NULL, 10);
+	mutex_lock(&data->update_lock);
 	tol_mask = w83792d_read_value(client,
 		W83792D_REG_TOLERANCE[nr]) & ((nr == 1) ? 0x0f : 0xf0);
 	tol_tmp = SENSORS_LIMIT(val, 0, 15);
@@ -877,6 +897,7 @@ store_tolerance(struct device *dev, struct device_attribute *attr,
 	}
 	w83792d_write_value(client, W83792D_REG_TOLERANCE[nr],
 		tol_mask | tol_tmp);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -915,11 +936,13 @@ store_sf2_point(struct device *dev, struct device_attribute *attr,
 	u8 mask_tmp = 0;
 
 	val = simple_strtoul(buf, NULL, 10);
+	mutex_lock(&data->update_lock);
 	data->sf2_points[index][nr] = SENSORS_LIMIT(val, 0, 127);
 	mask_tmp = w83792d_read_value(client,
 					W83792D_REG_POINTS[index][nr]) & 0x80;
 	w83792d_write_value(client, W83792D_REG_POINTS[index][nr],
 		mask_tmp|data->sf2_points[index][nr]);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -979,6 +1002,7 @@ store_sf2_level(struct device *dev, struct device_attribute *attr,
 	u8 mask_tmp=0, level_tmp=0;
 
 	val = simple_strtoul(buf, NULL, 10);
+	mutex_lock(&data->update_lock);
 	data->sf2_levels[index][nr] = SENSORS_LIMIT((val * 15) / 100, 0, 15);
 	mask_tmp = w83792d_read_value(client, W83792D_REG_LEVELS[index][nr])
 		& ((nr==3) ? 0xf0 : 0x0f);
@@ -988,6 +1012,7 @@ store_sf2_level(struct device *dev, struct device_attribute *attr,
 		level_tmp = data->sf2_levels[index][nr] << 4;
 	}
 	w83792d_write_value(client, W83792D_REG_LEVELS[index][nr], level_tmp | mask_tmp);
+	mutex_unlock(&data->update_lock);
 
 	return count;
 }
@@ -1373,7 +1398,7 @@ static struct w83792d_data *w83792d_update_device(struct device *dev)
 	struct i2c_client *client = to_i2c_client(dev);
 	struct w83792d_data *data = i2c_get_clientdata(client);
 	int i, j;
-	u8 reg_array_tmp[4], pwm_array_tmp[7], reg_tmp;
+	u8 reg_array_tmp[4], reg_tmp;
 
 	mutex_lock(&data->update_lock);
 
@@ -1402,10 +1427,8 @@ static struct w83792d_data *w83792d_update_device(struct device *dev)
 			data->fan_min[i] = w83792d_read_value(client,
 						W83792D_REG_FAN_MIN[i]);
 			/* Update the PWM/DC Value and PWM/DC flag */
-			pwm_array_tmp[i] = w83792d_read_value(client,
+			data->pwm[i] = w83792d_read_value(client,
 						W83792D_REG_PWM[i]);
-			data->pwm[i] = pwm_array_tmp[i] & 0x0f;
-			data->pwm_mode[i] = pwm_array_tmp[i] >> 7;
 		}
 
 		reg_tmp = w83792d_read_value(client, W83792D_REG_FAN_CFG);
@@ -1513,7 +1536,6 @@ static void w83792d_print_debug(struct w83792d_data *data, struct device *dev)
 		dev_dbg(dev, "fan[%d] is: 0x%x\n", i, data->fan[i]);
 		dev_dbg(dev, "fan[%d] min is: 0x%x\n", i, data->fan_min[i]);
 		dev_dbg(dev, "pwm[%d]     is: 0x%x\n", i, data->pwm[i]);
-		dev_dbg(dev, "pwm_mode[%d] is: 0x%x\n", i, data->pwm_mode[i]);
 	}
 	dev_dbg(dev, "3 set of Temperatures: =====>\n");
 	for (i=0; i<3; i++) {
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index d6d44946a28..f7af7e9bb7d 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -163,7 +163,7 @@ config I2C_PXA_SLAVE
 	  I2C bus.
 
 config I2C_PIIX4
-	tristate "Intel PIIX4"
+	tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)"
 	depends on I2C && PCI
 	help
 	  If you say yes to this option, support will be included for the Intel
@@ -172,6 +172,9 @@ config I2C_PIIX4
 	  of Broadcom):
 	    Intel PIIX4
 	    Intel 440MX
+	    ATI IXP200
+	    ATI IXP300
+	    ATI IXP400
 	    Serverworks OSB4
 	    Serverworks CSB5
 	    Serverworks CSB6
@@ -273,6 +276,17 @@ config I2C_NFORCE2
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-nforce2.
 
+config I2C_OCORES
+	tristate "OpenCores I2C Controller"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes to this option, support will be included for the
+	  OpenCores I2C controller. For details see
+	  http://www.opencores.org/projects.cgi/web/i2c/overview
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-ocores.
+
 config I2C_PARPORT
 	tristate "Parallel port adapter"
 	depends on I2C && PARPORT
@@ -500,6 +514,7 @@ config I2C_PCA_ISA
 	tristate "PCA9564 on an ISA bus"
 	depends on I2C
 	select I2C_ALGOPCA
+	default n
 	help
 	  This driver supports ISA boards using the Philips PCA 9564
 	  Parallel bus to I2C bus controller
@@ -507,6 +522,11 @@ config I2C_PCA_ISA
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-pca-isa.
 
+	  This device is almost undetectable and using this driver on a
+	  system which doesn't have this device will result in long
+	  delays when I2C/SMBus chip drivers are loaded (e.g. at boot
+	  time).  If unsure, say N.
+
 config I2C_MV64XXX
 	tristate "Marvell mv64xxx I2C Controller"
 	depends on I2C && MV64X60 && EXPERIMENTAL
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index b44831dff68..ac56df53155 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
 obj-$(CONFIG_I2C_MPC)		+= i2c-mpc.o
 obj-$(CONFIG_I2C_MV64XXX)	+= i2c-mv64xxx.o
 obj-$(CONFIG_I2C_NFORCE2)	+= i2c-nforce2.o
+obj-$(CONFIG_I2C_OCORES)	+= i2c-ocores.o
 obj-$(CONFIG_I2C_PARPORT)	+= i2c-parport.o
 obj-$(CONFIG_I2C_PARPORT_LIGHT)	+= i2c-parport-light.o
 obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index dfca7493362..3e0d04d5a80 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -1,5 +1,5 @@
 /*
-    i801.c - Part of lm_sensors, Linux kernel modules for hardware
+    i2c-i801.c - Part of lm_sensors, Linux kernel modules for hardware
               monitoring
     Copyright (c) 1998 - 2002  Frodo Looijaard <frodol@dds.nl>,
     Philip Edelbrock <phil@netroedge.com>, and Mark D. Studebaker
@@ -36,7 +36,7 @@
     This driver supports several versions of Intel's I/O Controller Hubs (ICH).
     For SMBus support, they are similar to the PIIX4 and are part
     of Intel's '810' and other chipsets.
-    See the doc/busses/i2c-i801 file for details.
+    See the file Documentation/i2c/busses/i2c-i801 for details.
     I2C Block Read and Process Call are not supported.
 */
 
@@ -66,9 +66,8 @@
 #define SMBAUXCTL	(13 + i801_smba)	/* ICH4 only */
 
 /* PCI Address Constants */
-#define SMBBA		0x020
+#define SMBBAR		4
 #define SMBHSTCFG	0x040
-#define SMBREV		0x008
 
 /* Host configuration bits for SMBHSTCFG */
 #define SMBHSTCFG_HST_EN	1
@@ -92,92 +91,16 @@
 #define I801_START		0x40
 #define I801_PEC_EN		0x80	/* ICH4 only */
 
-/* insmod parameters */
-
-/* If force_addr is set to anything different from 0, we forcibly enable
-   the I801 at the given address. VERY DANGEROUS! */
-static u16 force_addr;
-module_param(force_addr, ushort, 0);
-MODULE_PARM_DESC(force_addr,
-		 "Forcibly enable the I801 at the given address. "
-		 "EXTREMELY DANGEROUS!");
 
 static int i801_transaction(void);
 static int i801_block_transaction(union i2c_smbus_data *data, char read_write,
 				  int command, int hwpec);
 
-static unsigned short i801_smba;
+static unsigned long i801_smba;
 static struct pci_driver i801_driver;
 static struct pci_dev *I801_dev;
 static int isich4;
 
-static int i801_setup(struct pci_dev *dev)
-{
-	int error_return = 0;
-	unsigned char temp;
-
-	/* Note: we keep on searching until we have found 'function 3' */
-	if(PCI_FUNC(dev->devfn) != 3)
-		return -ENODEV;
-
-	I801_dev = dev;
-	if ((dev->device == PCI_DEVICE_ID_INTEL_82801DB_3) ||
-	    (dev->device == PCI_DEVICE_ID_INTEL_82801EB_3) ||
-	    (dev->device == PCI_DEVICE_ID_INTEL_ESB_4))
-		isich4 = 1;
-	else
-		isich4 = 0;
-
-	/* Determine the address of the SMBus areas */
-	if (force_addr) {
-		i801_smba = force_addr & 0xfff0;
-	} else {
-		pci_read_config_word(I801_dev, SMBBA, &i801_smba);
-		i801_smba &= 0xfff0;
-		if(i801_smba == 0) {
-			dev_err(&dev->dev, "SMB base address uninitialized "
-				"- upgrade BIOS or use force_addr=0xaddr\n");
-			return -ENODEV;
-		}
-	}
-
-	if (!request_region(i801_smba, (isich4 ? 16 : 8), i801_driver.name)) {
-		dev_err(&dev->dev, "I801_smb region 0x%x already in use!\n",
-			i801_smba);
-		error_return = -EBUSY;
-		goto END;
-	}
-
-	pci_read_config_byte(I801_dev, SMBHSTCFG, &temp);
-	temp &= ~SMBHSTCFG_I2C_EN;	/* SMBus timing */
-	pci_write_config_byte(I801_dev, SMBHSTCFG, temp);
-
-	/* If force_addr is set, we program the new address here. Just to make
-	   sure, we disable the device first. */
-	if (force_addr) {
-		pci_write_config_byte(I801_dev, SMBHSTCFG, temp & 0xfe);
-		pci_write_config_word(I801_dev, SMBBA, i801_smba);
-		pci_write_config_byte(I801_dev, SMBHSTCFG, temp | 0x01);
-		dev_warn(&dev->dev, "WARNING: I801 SMBus interface set to "
-			"new address %04x!\n", i801_smba);
-	} else if ((temp & 1) == 0) {
-		pci_write_config_byte(I801_dev, SMBHSTCFG, temp | 1);
-		dev_warn(&dev->dev, "enabling SMBus device\n");
-	}
-
-	if (temp & 0x02)
-		dev_dbg(&dev->dev, "I801 using Interrupt SMI# for SMBus.\n");
-	else
-		dev_dbg(&dev->dev, "I801 using PCI Interrupt for SMBus.\n");
-
-	pci_read_config_byte(I801_dev, SMBREV, &temp);
-	dev_dbg(&dev->dev, "SMBREV = 0x%X\n", temp);
-	dev_dbg(&dev->dev, "I801_smba = 0x%X\n", i801_smba);
-
-END:
-	return error_return;
-}
-
 static int i801_transaction(void)
 {
 	int temp;
@@ -334,8 +257,8 @@ static int i801_block_transaction(union i2c_smbus_data *data, char read_write,
 		/* We will always wait for a fraction of a second! */
 		timeout = 0;
 		do {
-			temp = inb_p(SMBHSTSTS);
 			msleep(1);
+			temp = inb_p(SMBHSTSTS);
 		}
 		    while ((!(temp & 0x80))
 			   && (timeout++ < MAX_TIMEOUT));
@@ -393,8 +316,8 @@ static int i801_block_transaction(union i2c_smbus_data *data, char read_write,
 		/* wait for INTR bit as advised by Intel */
 		timeout = 0;
 		do {
-			temp = inb_p(SMBHSTSTS);
 			msleep(1);
+			temp = inb_p(SMBHSTSTS);
 		} while ((!(temp & 0x02))
 			   && (timeout++ < MAX_TIMEOUT));
 
@@ -541,25 +464,76 @@ MODULE_DEVICE_TABLE (pci, i801_ids);
 
 static int __devinit i801_probe(struct pci_dev *dev, const struct pci_device_id *id)
 {
+	unsigned char temp;
+	int err;
+
+	I801_dev = dev;
+	if ((dev->device == PCI_DEVICE_ID_INTEL_82801DB_3) ||
+	    (dev->device == PCI_DEVICE_ID_INTEL_82801EB_3) ||
+	    (dev->device == PCI_DEVICE_ID_INTEL_ESB_4))
+		isich4 = 1;
+	else
+		isich4 = 0;
+
+	err = pci_enable_device(dev);
+	if (err) {
+		dev_err(&dev->dev, "Failed to enable SMBus PCI device (%d)\n",
+			err);
+		goto exit;
+	}
+
+	/* Determine the address of the SMBus area */
+	i801_smba = pci_resource_start(dev, SMBBAR);
+	if (!i801_smba) {
+		dev_err(&dev->dev, "SMBus base address uninitialized, "
+			"upgrade BIOS\n");
+		err = -ENODEV;
+		goto exit_disable;
+	}
+
+	err = pci_request_region(dev, SMBBAR, i801_driver.name);
+	if (err) {
+		dev_err(&dev->dev, "Failed to request SMBus region "
+			"0x%lx-0x%lx\n", i801_smba,
+			pci_resource_end(dev, SMBBAR));
+		goto exit_disable;
+	}
 
-	if (i801_setup(dev)) {
-		dev_warn(&dev->dev,
-			"I801 not detected, module not inserted.\n");
-		return -ENODEV;
+	pci_read_config_byte(I801_dev, SMBHSTCFG, &temp);
+	temp &= ~SMBHSTCFG_I2C_EN;	/* SMBus timing */
+	if (!(temp & SMBHSTCFG_HST_EN)) {
+		dev_info(&dev->dev, "Enabling SMBus device\n");
+		temp |= SMBHSTCFG_HST_EN;
 	}
+	pci_write_config_byte(I801_dev, SMBHSTCFG, temp);
+
+	if (temp & SMBHSTCFG_SMB_SMI_EN)
+		dev_dbg(&dev->dev, "SMBus using interrupt SMI#\n");
+	else
+		dev_dbg(&dev->dev, "SMBus using PCI Interrupt\n");
 
 	/* set up the driverfs linkage to our parent device */
 	i801_adapter.dev.parent = &dev->dev;
 
 	snprintf(i801_adapter.name, I2C_NAME_SIZE,
-		"SMBus I801 adapter at %04x", i801_smba);
-	return i2c_add_adapter(&i801_adapter);
+		"SMBus I801 adapter at %04lx", i801_smba);
+	err = i2c_add_adapter(&i801_adapter);
+	if (err) {
+		dev_err(&dev->dev, "Failed to add SMBus adapter\n");
+		goto exit_disable;
+	}
+
+exit_disable:
+	pci_disable_device(dev);
+exit:
+	return err;
 }
 
 static void __devexit i801_remove(struct pci_dev *dev)
 {
 	i2c_del_adapter(&i801_adapter);
-	release_region(i801_smba, (isich4 ? 16 : 8));
+	pci_release_region(dev, SMBBAR);
+	pci_disable_device(dev);
 }
 
 static struct pci_driver i801_driver = {
diff --git a/drivers/i2c/busses/i2c-nforce2.c b/drivers/i2c/busses/i2c-nforce2.c
index 2d80eb26f68..604b49e22df 100644
--- a/drivers/i2c/busses/i2c-nforce2.c
+++ b/drivers/i2c/busses/i2c-nforce2.c
@@ -31,6 +31,8 @@
     nForce3 250Gb MCP		00E4
     nForce4 MCP			0052
     nForce4 MCP-04		0034
+    nForce4 MCP51		0264
+    nForce4 MCP55		0368
 
     This driver supports the 2 SMBuses that are included in the MCP of the
     nForce2/3/4 chipsets.
@@ -64,6 +66,7 @@ struct nforce2_smbus {
 
 /*
  * nVidia nForce2 SMBus control register definitions
+ * (Newer incarnations use standard BARs 4 and 5 instead)
  */
 #define NFORCE_PCI_SMB1	0x50
 #define NFORCE_PCI_SMB2	0x54
@@ -259,6 +262,8 @@ static struct pci_device_id nforce2_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE4_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_SMBUS) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SMBUS) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SMBUS) },
 	{ 0 }
 };
 
@@ -266,19 +271,29 @@ static struct pci_device_id nforce2_ids[] = {
 MODULE_DEVICE_TABLE (pci, nforce2_ids);
 
 
-static int __devinit nforce2_probe_smb (struct pci_dev *dev, int reg,
-	struct nforce2_smbus *smbus, char *name)
+static int __devinit nforce2_probe_smb (struct pci_dev *dev, int bar,
+	int alt_reg, struct nforce2_smbus *smbus, const char *name)
 {
-	u16 iobase;
 	int error;
 
-	if (pci_read_config_word(dev, reg, &iobase) != PCIBIOS_SUCCESSFUL) {
-		dev_err(&smbus->adapter.dev, "Error reading PCI config for %s\n", name);
-		return -1;
+	smbus->base = pci_resource_start(dev, bar);
+	if (smbus->base) {
+		smbus->size = pci_resource_len(dev, bar);
+	} else {
+		/* Older incarnations of the device used non-standard BARs */
+		u16 iobase;
+
+		if (pci_read_config_word(dev, alt_reg, &iobase)
+		    != PCIBIOS_SUCCESSFUL) {
+			dev_err(&dev->dev, "Error reading PCI config for %s\n",
+				name);
+			return -1;
+		}
+
+		smbus->base = iobase & PCI_BASE_ADDRESS_IO_MASK;
+		smbus->size = 8;
 	}
-	smbus->dev  = dev;
-	smbus->base = iobase & 0xfffc;
-	smbus->size = 8;
+	smbus->dev = dev;
 
 	if (!request_region(smbus->base, smbus->size, nforce2_driver.name)) {
 		dev_err(&smbus->adapter.dev, "Error requesting region %02x .. %02X for %s\n",
@@ -313,12 +328,13 @@ static int __devinit nforce2_probe(struct pci_dev *dev, const struct pci_device_
 	pci_set_drvdata(dev, smbuses);
 
 	/* SMBus adapter 1 */
-	res1 = nforce2_probe_smb (dev, NFORCE_PCI_SMB1, &smbuses[0], "SMB1");
+	res1 = nforce2_probe_smb(dev, 4, NFORCE_PCI_SMB1, &smbuses[0], "SMB1");
 	if (res1 < 0) {
 		dev_err(&dev->dev, "Error probing SMB1.\n");
 		smbuses[0].base = 0;	/* to have a check value */
 	}
-	res2 = nforce2_probe_smb (dev, NFORCE_PCI_SMB2, &smbuses[1], "SMB2");
+	/* SMBus adapter 2 */
+	res2 = nforce2_probe_smb(dev, 5, NFORCE_PCI_SMB2, &smbuses[1], "SMB2");
 	if (res2 < 0) {
 		dev_err(&dev->dev, "Error probing SMB2.\n");
 		smbuses[1].base = 0;	/* to have a check value */
diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c
new file mode 100644
index 00000000000..592824087c4
--- /dev/null
+++ b/drivers/i2c/busses/i2c-ocores.c
@@ -0,0 +1,341 @@
+/*
+ * i2c-ocores.c: I2C bus driver for OpenCores I2C controller
+ * (http://www.opencores.org/projects.cgi/web/i2c/overview).
+ *
+ * Peter Korsgaard <jacmet@sunsite.dk>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/wait.h>
+#include <linux/i2c-ocores.h>
+#include <asm/io.h>
+
+struct ocores_i2c {
+	void __iomem *base;
+	int regstep;
+	wait_queue_head_t wait;
+	struct i2c_adapter adap;
+	struct i2c_msg *msg;
+	int pos;
+	int nmsgs;
+	int state; /* see STATE_ */
+};
+
+/* registers */
+#define OCI2C_PRELOW		0
+#define OCI2C_PREHIGH		1
+#define OCI2C_CONTROL		2
+#define OCI2C_DATA		3
+#define OCI2C_CMD		4 /* write only */
+#define OCI2C_STATUS		4 /* read only, same address as OCI2C_CMD */
+
+#define OCI2C_CTRL_IEN		0x40
+#define OCI2C_CTRL_EN		0x80
+
+#define OCI2C_CMD_START		0x91
+#define OCI2C_CMD_STOP		0x41
+#define OCI2C_CMD_READ		0x21
+#define OCI2C_CMD_WRITE		0x11
+#define OCI2C_CMD_READ_ACK	0x21
+#define OCI2C_CMD_READ_NACK	0x29
+#define OCI2C_CMD_IACK		0x01
+
+#define OCI2C_STAT_IF		0x01
+#define OCI2C_STAT_TIP		0x02
+#define OCI2C_STAT_ARBLOST	0x20
+#define OCI2C_STAT_BUSY		0x40
+#define OCI2C_STAT_NACK		0x80
+
+#define STATE_DONE		0
+#define STATE_START		1
+#define STATE_WRITE		2
+#define STATE_READ		3
+#define STATE_ERROR		4
+
+static inline void oc_setreg(struct ocores_i2c *i2c, int reg, u8 value)
+{
+	iowrite8(value, i2c->base + reg * i2c->regstep);
+}
+
+static inline u8 oc_getreg(struct ocores_i2c *i2c, int reg)
+{
+	return ioread8(i2c->base + reg * i2c->regstep);
+}
+
+static void ocores_process(struct ocores_i2c *i2c)
+{
+	struct i2c_msg *msg = i2c->msg;
+	u8 stat = oc_getreg(i2c, OCI2C_STATUS);
+
+	if ((i2c->state == STATE_DONE) || (i2c->state == STATE_ERROR)) {
+		/* stop has been sent */
+		oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_IACK);
+		wake_up(&i2c->wait);
+		return;
+	}
+
+	/* error? */
+	if (stat & OCI2C_STAT_ARBLOST) {
+		i2c->state = STATE_ERROR;
+		oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_STOP);
+		return;
+	}
+
+	if ((i2c->state == STATE_START) || (i2c->state == STATE_WRITE)) {
+		i2c->state =
+			(msg->flags & I2C_M_RD) ? STATE_READ : STATE_WRITE;
+
+		if (stat & OCI2C_STAT_NACK) {
+			i2c->state = STATE_ERROR;
+			oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_STOP);
+			return;
+		}
+	} else
+		msg->buf[i2c->pos++] = oc_getreg(i2c, OCI2C_DATA);
+
+	/* end of msg? */
+	if (i2c->pos == msg->len) {
+		i2c->nmsgs--;
+		i2c->msg++;
+		i2c->pos = 0;
+		msg = i2c->msg;
+
+		if (i2c->nmsgs) {	/* end? */
+			/* send start? */
+			if (!(msg->flags & I2C_M_NOSTART)) {
+				u8 addr = (msg->addr << 1);
+
+				if (msg->flags & I2C_M_RD)
+					addr |= 1;
+
+				i2c->state = STATE_START;
+
+				oc_setreg(i2c, OCI2C_DATA, addr);
+				oc_setreg(i2c, OCI2C_CMD,  OCI2C_CMD_START);
+				return;
+			} else
+				i2c->state = (msg->flags & I2C_M_RD)
+					? STATE_READ : STATE_WRITE;
+		} else {
+			i2c->state = STATE_DONE;
+			oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_STOP);
+			return;
+		}
+	}
+
+	if (i2c->state == STATE_READ) {
+		oc_setreg(i2c, OCI2C_CMD, i2c->pos == (msg->len-1) ?
+			  OCI2C_CMD_READ_NACK : OCI2C_CMD_READ_ACK);
+	} else {
+		oc_setreg(i2c, OCI2C_DATA, msg->buf[i2c->pos++]);
+		oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_WRITE);
+	}
+}
+
+static irqreturn_t ocores_isr(int irq, void *dev_id, struct pt_regs *regs)
+{
+	struct ocores_i2c *i2c = dev_id;
+
+	ocores_process(i2c);
+
+	return IRQ_HANDLED;
+}
+
+static int ocores_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
+{
+	struct ocores_i2c *i2c = i2c_get_adapdata(adap);
+
+	i2c->msg = msgs;
+	i2c->pos = 0;
+	i2c->nmsgs = num;
+	i2c->state = STATE_START;
+
+	oc_setreg(i2c, OCI2C_DATA,
+			(i2c->msg->addr << 1) |
+			((i2c->msg->flags & I2C_M_RD) ? 1:0));
+
+	oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_START);
+
+	if (wait_event_timeout(i2c->wait, (i2c->state == STATE_ERROR) ||
+			       (i2c->state == STATE_DONE), HZ))
+		return (i2c->state == STATE_DONE) ? num : -EIO;
+	else
+		return -ETIMEDOUT;
+}
+
+static void ocores_init(struct ocores_i2c *i2c,
+			struct ocores_i2c_platform_data *pdata)
+{
+	int prescale;
+	u8 ctrl = oc_getreg(i2c, OCI2C_CONTROL);
+
+	/* make sure the device is disabled */
+	oc_setreg(i2c, OCI2C_CONTROL, ctrl & ~(OCI2C_CTRL_EN|OCI2C_CTRL_IEN));
+
+	prescale = (pdata->clock_khz / (5*100)) - 1;
+	oc_setreg(i2c, OCI2C_PRELOW, prescale & 0xff);
+	oc_setreg(i2c, OCI2C_PREHIGH, prescale >> 8);
+
+	/* Init the device */
+	oc_setreg(i2c, OCI2C_CMD, OCI2C_CMD_IACK);
+	oc_setreg(i2c, OCI2C_CONTROL, ctrl | OCI2C_CTRL_IEN | OCI2C_CTRL_EN);
+}
+
+
+static u32 ocores_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static struct i2c_algorithm ocores_algorithm = {
+	.master_xfer	= ocores_xfer,
+	.functionality	= ocores_func,
+};
+
+static struct i2c_adapter ocores_adapter = {
+	.owner		= THIS_MODULE,
+	.name		= "i2c-ocores",
+	.class		= I2C_CLASS_HWMON,
+	.algo		= &ocores_algorithm,
+};
+
+
+static int __devinit ocores_i2c_probe(struct platform_device *pdev)
+{
+	struct ocores_i2c *i2c;
+	struct ocores_i2c_platform_data *pdata;
+	struct resource *res, *res2;
+	int ret;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+
+	res2 = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res2)
+		return -ENODEV;
+
+	pdata = (struct ocores_i2c_platform_data*) pdev->dev.platform_data;
+	if (!pdata)
+		return -ENODEV;
+
+	i2c = kzalloc(sizeof(*i2c), GFP_KERNEL);
+	if (!i2c)
+		return -ENOMEM;
+
+	if (!request_mem_region(res->start, res->end - res->start + 1,
+				pdev->name)) {
+		dev_err(&pdev->dev, "Memory region busy\n");
+		ret = -EBUSY;
+		goto request_mem_failed;
+	}
+
+	i2c->base = ioremap(res->start, res->end - res->start + 1);
+	if (!i2c->base) {
+		dev_err(&pdev->dev, "Unable to map registers\n");
+		ret = -EIO;
+		goto map_failed;
+	}
+
+	i2c->regstep = pdata->regstep;
+	ocores_init(i2c, pdata);
+
+	init_waitqueue_head(&i2c->wait);
+	ret = request_irq(res2->start, ocores_isr, 0, pdev->name, i2c);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot claim IRQ\n");
+		goto request_irq_failed;
+	}
+
+	/* hook up driver to tree */
+	platform_set_drvdata(pdev, i2c);
+	i2c->adap = ocores_adapter;
+	i2c_set_adapdata(&i2c->adap, i2c);
+	i2c->adap.dev.parent = &pdev->dev;
+
+	/* add i2c adapter to i2c tree */
+	ret = i2c_add_adapter(&i2c->adap);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to add adapter\n");
+		goto add_adapter_failed;
+	}
+
+	return 0;
+
+add_adapter_failed:
+	free_irq(res2->start, i2c);
+request_irq_failed:
+	iounmap(i2c->base);
+map_failed:
+	release_mem_region(res->start, res->end - res->start + 1);
+request_mem_failed:
+	kfree(i2c);
+
+	return ret;
+}
+
+static int __devexit ocores_i2c_remove(struct platform_device* pdev)
+{
+	struct ocores_i2c *i2c = platform_get_drvdata(pdev);
+	struct resource *res;
+
+	/* disable i2c logic */
+	oc_setreg(i2c, OCI2C_CONTROL, oc_getreg(i2c, OCI2C_CONTROL)
+		  & ~(OCI2C_CTRL_EN|OCI2C_CTRL_IEN));
+
+	/* remove adapter & data */
+	i2c_del_adapter(&i2c->adap);
+	platform_set_drvdata(pdev, NULL);
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (res)
+		free_irq(res->start, i2c);
+
+	iounmap(i2c->base);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res)
+		release_mem_region(res->start, res->end - res->start + 1);
+
+	kfree(i2c);
+
+	return 0;
+}
+
+static struct platform_driver ocores_i2c_driver = {
+	.probe  = ocores_i2c_probe,
+	.remove = __devexit_p(ocores_i2c_remove),
+	.driver = {
+		.owner = THIS_MODULE,
+		.name = "ocores-i2c",
+	},
+};
+
+static int __init ocores_i2c_init(void)
+{
+	return platform_driver_register(&ocores_i2c_driver);
+}
+
+static void __exit ocores_i2c_exit(void)
+{
+	platform_driver_unregister(&ocores_i2c_driver);
+}
+
+module_init(ocores_i2c_init);
+module_exit(ocores_i2c_exit);
+
+MODULE_AUTHOR("Peter Korsgaard <jacmet@sunsite.dk>");
+MODULE_DESCRIPTION("OpenCores I2C bus driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c
index d9c7c00e71f..8f2f65b793b 100644
--- a/drivers/i2c/busses/i2c-piix4.c
+++ b/drivers/i2c/busses/i2c-piix4.c
@@ -102,13 +102,6 @@ MODULE_PARM_DESC(force_addr,
 		 "Forcibly enable the PIIX4 at the given address. "
 		 "EXTREMELY DANGEROUS!");
 
-/* If fix_hstcfg is set to anything different from 0, we reset one of the
-   registers to be a valid value. */
-static int fix_hstcfg;
-module_param (fix_hstcfg, int, 0);
-MODULE_PARM_DESC(fix_hstcfg,
-		"Fix config register. Needed on some boards (Force CPCI735).");
-
 static int piix4_transaction(void);
 
 static unsigned short piix4_smba;
@@ -137,7 +130,7 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev,
 	/* Don't access SMBus on IBM systems which get corrupted eeproms */
 	if (dmi_check_system(piix4_dmi_table) &&
 			PIIX4_dev->vendor == PCI_VENDOR_ID_INTEL) {
-		dev_err(&PIIX4_dev->dev, "IBM Laptop detected; this module "
+		dev_err(&PIIX4_dev->dev, "IBM system detected; this module "
 			"may corrupt your serial eeprom! Refusing to load "
 			"module!\n");
 		return -EPERM;
@@ -166,22 +159,6 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev,
 
 	pci_read_config_byte(PIIX4_dev, SMBHSTCFG, &temp);
 
-	/* Some BIOS will set up the chipset incorrectly and leave a register
-	   in an undefined state (causing I2C to act very strangely). */
-	if (temp & 0x02) {
-		if (fix_hstcfg) {
-			dev_info(&PIIX4_dev->dev, "Working around buggy BIOS "
-					"(I2C)\n");
-			temp &= 0xfd;
-			pci_write_config_byte(PIIX4_dev, SMBHSTCFG, temp);
-		} else {
-			dev_info(&PIIX4_dev->dev, "Unusual config register "
-					"value\n");
-			dev_info(&PIIX4_dev->dev, "Try using fix_hstcfg=1 if "
-					"you experience problems\n");
-		}
-	}
- 
 	/* If force_addr is set, we program the new address here. Just to make
 	   sure, we disable the PIIX4 first. */
 	if (force_addr) {
@@ -214,7 +191,7 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev,
 		}
 	}
 
-	if ((temp & 0x0E) == 8)
+	if (((temp & 0x0E) == 8) || ((temp & 0x0E) == 2))
 		dev_dbg(&PIIX4_dev->dev, "Using Interrupt 9 for SMBus.\n");
 	else if ((temp & 0x0E) == 0)
 		dev_dbg(&PIIX4_dev->dev, "Using Interrupt SMI# for SMBus.\n");
@@ -413,6 +390,12 @@ static struct i2c_adapter piix4_adapter = {
 static struct pci_device_id piix4_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3),
 	  .driver_data = 3 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP200_SMBUS),
+	  .driver_data = 0 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_SMBUS),
+	  .driver_data = 0 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_SMBUS),
+	  .driver_data = 0 },
 	{ PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4),
 	  .driver_data = 0 },
 	{ PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5),
diff --git a/drivers/i2c/busses/scx200_acb.c b/drivers/i2c/busses/scx200_acb.c
index 766cc969c4d..22a3eda0416 100644
--- a/drivers/i2c/busses/scx200_acb.c
+++ b/drivers/i2c/busses/scx200_acb.c
@@ -33,7 +33,6 @@
 #include <linux/delay.h>
 #include <linux/mutex.h>
 #include <asm/io.h>
-#include <asm/msr.h>
 
 #include <linux/scx200.h>
 
@@ -85,6 +84,10 @@ struct scx200_acb_iface {
 	u8 *ptr;
 	char needs_reset;
 	unsigned len;
+
+	/* PCI device info */
+	struct pci_dev *pdev;
+	int bar;
 };
 
 /* Register Definitions */
@@ -381,7 +384,7 @@ static struct i2c_algorithm scx200_acb_algorithm = {
 static struct scx200_acb_iface *scx200_acb_list;
 static DECLARE_MUTEX(scx200_acb_list_mutex);
 
-static int scx200_acb_probe(struct scx200_acb_iface *iface)
+static __init int scx200_acb_probe(struct scx200_acb_iface *iface)
 {
 	u8 val;
 
@@ -417,17 +420,16 @@ static int scx200_acb_probe(struct scx200_acb_iface *iface)
 	return 0;
 }
 
-static int  __init scx200_acb_create(const char *text, int base, int index)
+static __init struct scx200_acb_iface *scx200_create_iface(const char *text,
+		int index)
 {
 	struct scx200_acb_iface *iface;
 	struct i2c_adapter *adapter;
-	int rc;
 
 	iface = kzalloc(sizeof(*iface), GFP_KERNEL);
 	if (!iface) {
 		printk(KERN_ERR NAME ": can't allocate memory\n");
-		rc = -ENOMEM;
-		goto errout;
+		return NULL;
 	}
 
 	adapter = &iface->adapter;
@@ -440,26 +442,27 @@ static int  __init scx200_acb_create(const char *text, int base, int index)
 
 	mutex_init(&iface->mutex);
 
-	if (!request_region(base, 8, adapter->name)) {
-		printk(KERN_ERR NAME ": can't allocate io 0x%x-0x%x\n",
-			base, base + 8-1);
-		rc = -EBUSY;
-		goto errout_free;
-	}
-	iface->base = base;
+	return iface;
+}
+
+static int __init scx200_acb_create(struct scx200_acb_iface *iface)
+{
+	struct i2c_adapter *adapter;
+	int rc;
+
+	adapter = &iface->adapter;
 
 	rc = scx200_acb_probe(iface);
 	if (rc) {
 		printk(KERN_WARNING NAME ": probe failed\n");
-		goto errout_release;
+		return rc;
 	}
 
 	scx200_acb_reset(iface);
 
 	if (i2c_add_adapter(adapter) < 0) {
 		printk(KERN_ERR NAME ": failed to register\n");
-		rc = -ENODEV;
-		goto errout_release;
+		return -ENODEV;
 	}
 
 	down(&scx200_acb_list_mutex);
@@ -468,64 +471,148 @@ static int  __init scx200_acb_create(const char *text, int base, int index)
 	up(&scx200_acb_list_mutex);
 
 	return 0;
+}
 
- errout_release:
-	release_region(iface->base, 8);
+static __init int scx200_create_pci(const char *text, struct pci_dev *pdev,
+		int bar)
+{
+	struct scx200_acb_iface *iface;
+	int rc;
+
+	iface = scx200_create_iface(text, 0);
+
+	if (iface == NULL)
+		return -ENOMEM;
+
+	iface->pdev = pdev;
+	iface->bar = bar;
+
+	pci_enable_device_bars(iface->pdev, 1 << iface->bar);
+
+	rc = pci_request_region(iface->pdev, iface->bar, iface->adapter.name);
+
+	if (rc != 0) {
+		printk(KERN_ERR NAME ": can't allocate PCI BAR %d\n",
+				iface->bar);
+		goto errout_free;
+	}
+
+	iface->base = pci_resource_start(iface->pdev, iface->bar);
+	rc = scx200_acb_create(iface);
+
+	if (rc == 0)
+		return 0;
+
+	pci_release_region(iface->pdev, iface->bar);
+	pci_dev_put(iface->pdev);
  errout_free:
 	kfree(iface);
- errout:
 	return rc;
 }
 
-static struct pci_device_id scx200[] = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_BRIDGE) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SC1100_BRIDGE) },
-	{ },
-};
+static int __init scx200_create_isa(const char *text, unsigned long base,
+		int index)
+{
+	struct scx200_acb_iface *iface;
+	int rc;
+
+	iface = scx200_create_iface(text, index);
+
+	if (iface == NULL)
+		return -ENOMEM;
+
+	if (request_region(base, 8, iface->adapter.name) == 0) {
+		printk(KERN_ERR NAME ": can't allocate io 0x%lx-0x%lx\n",
+		       base, base + 8 - 1);
+		rc = -EBUSY;
+		goto errout_free;
+	}
+
+	iface->base = base;
+	rc = scx200_acb_create(iface);
+
+	if (rc == 0)
+		return 0;
 
-static struct pci_device_id divil_pci[] = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_NS,  PCI_DEVICE_ID_NS_CS5535_ISA) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA) },
-	{ } /* NULL entry */
+	release_region(base, 8);
+ errout_free:
+	kfree(iface);
+	return rc;
+}
+
+/* Driver data is an index into the scx200_data array that indicates
+ * the name and the BAR where the I/O address resource is located.  ISA
+ * devices are flagged with a bar value of -1 */
+
+static struct pci_device_id scx200_pci[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_BRIDGE),
+	  .driver_data = 0 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SC1100_BRIDGE),
+	  .driver_data = 0 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_CS5535_ISA),
+	  .driver_data = 1 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA),
+	  .driver_data = 2 }
 };
 
-#define MSR_LBAR_SMB		0x5140000B
+static struct {
+	const char *name;
+	int bar;
+} scx200_data[] = {
+	{ "SCx200", -1 },
+	{ "CS5535",  0 },
+	{ "CS5536",  0 }
+};
 
-static __init int scx200_add_cs553x(void)
+static __init int scx200_scan_pci(void)
 {
-	u32	low, hi;
-	u32	smb_base;
-
-	/* Grab & reserve the SMB I/O range */
-	rdmsr(MSR_LBAR_SMB, low, hi);
+	int data, dev;
+	int rc = -ENODEV;
+	struct pci_dev *pdev;
+
+	for(dev = 0; dev < ARRAY_SIZE(scx200_pci); dev++) {
+		pdev = pci_get_device(scx200_pci[dev].vendor,
+				scx200_pci[dev].device, NULL);
+
+		if (pdev == NULL)
+			continue;
+
+		data = scx200_pci[dev].driver_data;
+
+		/* if .bar is greater or equal to zero, this is a
+		 * PCI device - otherwise, we assume
+		   that the ports are ISA based
+		*/
+
+		if (scx200_data[data].bar >= 0)
+			rc = scx200_create_pci(scx200_data[data].name, pdev,
+					scx200_data[data].bar);
+		else {
+			int i;
+
+			for (i = 0; i < MAX_DEVICES; ++i) {
+				if (base[i] == 0)
+					continue;
+
+				rc = scx200_create_isa(scx200_data[data].name,
+						base[i],
+						i);
+			}
+		}
 
-	/* Check the IO mask and whether SMB is enabled */
-	if (hi != 0x0000F001) {
-		printk(KERN_WARNING NAME ": SMBus not enabled\n");
-		return -ENODEV;
+		break;
 	}
 
-	/* SMBus IO size is 8 bytes */
-	smb_base = low & 0x0000FFF8;
-
-	return scx200_acb_create("CS5535", smb_base, 0);
+	return rc;
 }
 
 static int __init scx200_acb_init(void)
 {
-	int i;
-	int	rc = -ENODEV;
+	int rc;
 
 	pr_debug(NAME ": NatSemi SCx200 ACCESS.bus Driver\n");
 
-	/* Verify that this really is a SCx200 processor */
-	if (pci_dev_present(scx200)) {
-		for (i = 0; i < MAX_DEVICES; ++i) {
-			if (base[i] > 0)
-				rc = scx200_acb_create("SCx200", base[i], i);
-		}
-	} else if (pci_dev_present(divil_pci))
-		rc = scx200_add_cs553x();
+	rc = scx200_scan_pci();
 
 	/* If at least one bus was created, init must succeed */
 	if (scx200_acb_list)
@@ -543,7 +630,14 @@ static void __exit scx200_acb_cleanup(void)
 		up(&scx200_acb_list_mutex);
 
 		i2c_del_adapter(&iface->adapter);
-		release_region(iface->base, 8);
+
+		if (iface->pdev) {
+			pci_release_region(iface->pdev, iface->bar);
+			pci_dev_put(iface->pdev);
+		}
+		else
+			release_region(iface->base, 8);
+
 		kfree(iface);
 		down(&scx200_acb_list_mutex);
 	}
diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig
index 7aa5c38f085..87ee3ce5861 100644
--- a/drivers/i2c/chips/Kconfig
+++ b/drivers/i2c/chips/Kconfig
@@ -39,6 +39,7 @@ config SENSORS_EEPROM
 config SENSORS_PCF8574
 	tristate "Philips PCF8574 and PCF8574A"
 	depends on I2C && EXPERIMENTAL
+	default n
 	help
 	  If you say yes here you get support for Philips PCF8574 and 
 	  PCF8574A chips.
@@ -46,6 +47,9 @@ config SENSORS_PCF8574
 	  This driver can also be built as a module.  If so, the module
 	  will be called pcf8574.
 
+	  These devices are hard to detect and rarely found on mainstream
+	  hardware.  If unsure, say N.
+
 config SENSORS_PCA9539
 	tristate "Philips PCA9539 16-bit I/O port"
 	depends on I2C && EXPERIMENTAL
@@ -59,12 +63,16 @@ config SENSORS_PCA9539
 config SENSORS_PCF8591
 	tristate "Philips PCF8591"
 	depends on I2C && EXPERIMENTAL
+	default n
 	help
 	  If you say yes here you get support for Philips PCF8591 chips.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called pcf8591.
 
+	  These devices are hard to detect and rarely found on mainstream
+	  hardware.  If unsure, say N.
+
 config ISP1301_OMAP
 	tristate "Philips ISP1301 with OMAP OTG"
 	depends on I2C && ARCH_OMAP_OTG
diff --git a/drivers/i2c/chips/m41t00.c b/drivers/i2c/chips/m41t00.c
index 99ab4ec3439..2dd0a34d947 100644
--- a/drivers/i2c/chips/m41t00.c
+++ b/drivers/i2c/chips/m41t00.c
@@ -1,11 +1,9 @@
 /*
- * drivers/i2c/chips/m41t00.c
- *
- * I2C client/driver for the ST M41T00 Real-Time Clock chip.
+ * I2C client/driver for the ST M41T00 family of i2c rtc chips.
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
+ * 2005, 2006 (c) MontaVista Software, Inc. This file is licensed under
  * the terms of the GNU General Public License version 2. This program
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
@@ -13,9 +11,6 @@
 /*
  * This i2c client/driver wedges between the drivers/char/genrtc.c RTC
  * interface and the SMBus interface of the i2c subsystem.
- * It would be more efficient to use i2c msgs/i2c_transfer directly but, as
- * recommened in .../Documentation/i2c/writing-clients section
- * "Sending and receiving", using SMBus level communication is preferred.
  */
 
 #include <linux/kernel.h>
@@ -24,56 +19,110 @@
 #include <linux/i2c.h>
 #include <linux/rtc.h>
 #include <linux/bcd.h>
-#include <linux/mutex.h>
 #include <linux/workqueue.h>
-
+#include <linux/platform_device.h>
+#include <linux/m41t00.h>
 #include <asm/time.h>
 #include <asm/rtc.h>
 
-#define	M41T00_DRV_NAME		"m41t00"
-
-static DEFINE_MUTEX(m41t00_mutex);
-
 static struct i2c_driver m41t00_driver;
 static struct i2c_client *save_client;
 
 static unsigned short ignore[] = { I2C_CLIENT_END };
-static unsigned short normal_addr[] = { 0x68, I2C_CLIENT_END };
+static unsigned short normal_addr[] = { I2C_CLIENT_END, I2C_CLIENT_END };
 
 static struct i2c_client_address_data addr_data = {
-	.normal_i2c		= normal_addr,
-	.probe			= ignore,
-	.ignore			= ignore,
+	.normal_i2c	= normal_addr,
+	.probe		= ignore,
+	.ignore		= ignore,
+};
+
+struct m41t00_chip_info {
+	u8	type;
+	char	*name;
+	u8	read_limit;
+	u8	sec;		/* Offsets for chip regs */
+	u8	min;
+	u8	hour;
+	u8	day;
+	u8	mon;
+	u8	year;
+	u8	alarm_mon;
+	u8	alarm_hour;
+	u8	sqw;
+	u8	sqw_freq;
 };
 
+static struct m41t00_chip_info m41t00_chip_info_tbl[] = {
+	{
+		.type		= M41T00_TYPE_M41T00,
+		.name		= "m41t00",
+		.read_limit	= 5,
+		.sec		= 0,
+		.min		= 1,
+		.hour		= 2,
+		.day		= 4,
+		.mon		= 5,
+		.year		= 6,
+	},
+	{
+		.type		= M41T00_TYPE_M41T81,
+		.name		= "m41t81",
+		.read_limit	= 1,
+		.sec		= 1,
+		.min		= 2,
+		.hour		= 3,
+		.day		= 5,
+		.mon		= 6,
+		.year		= 7,
+		.alarm_mon	= 0xa,
+		.alarm_hour	= 0xc,
+		.sqw		= 0x13,
+	},
+	{
+		.type		= M41T00_TYPE_M41T85,
+		.name		= "m41t85",
+		.read_limit	= 1,
+		.sec		= 1,
+		.min		= 2,
+		.hour		= 3,
+		.day		= 5,
+		.mon		= 6,
+		.year		= 7,
+		.alarm_mon	= 0xa,
+		.alarm_hour	= 0xc,
+		.sqw		= 0x13,
+	},
+};
+static struct m41t00_chip_info *m41t00_chip;
+
 ulong
 m41t00_get_rtc_time(void)
 {
-	s32	sec, min, hour, day, mon, year;
-	s32	sec1, min1, hour1, day1, mon1, year1;
-	ulong	limit = 10;
+	s32 sec, min, hour, day, mon, year;
+	s32 sec1, min1, hour1, day1, mon1, year1;
+	u8 reads = 0;
+	u8 buf[8], msgbuf[1] = { 0 }; /* offset into rtc's regs */
+	struct i2c_msg msgs[] = {
+		{
+			.addr	= save_client->addr,
+			.flags	= 0,
+			.len	= 1,
+			.buf	= msgbuf,
+		},
+		{
+			.addr	= save_client->addr,
+			.flags	= I2C_M_RD,
+			.len	= 8,
+			.buf	= buf,
+		},
+	};
 
 	sec = min = hour = day = mon = year = 0;
-	sec1 = min1 = hour1 = day1 = mon1 = year1 = 0;
 
-	mutex_lock(&m41t00_mutex);
 	do {
-		if (((sec = i2c_smbus_read_byte_data(save_client, 0)) >= 0)
-			&& ((min = i2c_smbus_read_byte_data(save_client, 1))
-				>= 0)
-			&& ((hour = i2c_smbus_read_byte_data(save_client, 2))
-				>= 0)
-			&& ((day = i2c_smbus_read_byte_data(save_client, 4))
-				>= 0)
-			&& ((mon = i2c_smbus_read_byte_data(save_client, 5))
-				>= 0)
-			&& ((year = i2c_smbus_read_byte_data(save_client, 6))
-				>= 0)
-			&& ((sec == sec1) && (min == min1) && (hour == hour1)
-				&& (day == day1) && (mon == mon1)
-				&& (year == year1)))
-
-				break;
+		if (i2c_transfer(save_client->adapter, msgs, 2) < 0)
+			goto read_err;
 
 		sec1 = sec;
 		min1 = min;
@@ -81,69 +130,88 @@ m41t00_get_rtc_time(void)
 		day1 = day;
 		mon1 = mon;
 		year1 = year;
-	} while (--limit > 0);
-	mutex_unlock(&m41t00_mutex);
-
-	if (limit == 0) {
-		dev_warn(&save_client->dev,
-			"m41t00: can't read rtc chip\n");
-		sec = min = hour = day = mon = year = 0;
-	}
-
-	sec &= 0x7f;
-	min &= 0x7f;
-	hour &= 0x3f;
-	day &= 0x3f;
-	mon &= 0x1f;
-	year &= 0xff;
 
-	BCD_TO_BIN(sec);
-	BCD_TO_BIN(min);
-	BCD_TO_BIN(hour);
-	BCD_TO_BIN(day);
-	BCD_TO_BIN(mon);
-	BCD_TO_BIN(year);
+		sec = buf[m41t00_chip->sec] & 0x7f;
+		min = buf[m41t00_chip->min] & 0x7f;
+		hour = buf[m41t00_chip->hour] & 0x3f;
+		day = buf[m41t00_chip->day] & 0x3f;
+		mon = buf[m41t00_chip->mon] & 0x1f;
+		year = buf[m41t00_chip->year];
+	} while ((++reads < m41t00_chip->read_limit) && ((sec != sec1)
+			|| (min != min1) || (hour != hour1) || (day != day1)
+			|| (mon != mon1) || (year != year1)));
+
+	if ((m41t00_chip->read_limit > 1) && ((sec != sec1) || (min != min1)
+			|| (hour != hour1) || (day != day1) || (mon != mon1)
+			|| (year != year1)))
+		goto read_err;
+
+	sec = BCD2BIN(sec);
+	min = BCD2BIN(min);
+	hour = BCD2BIN(hour);
+	day = BCD2BIN(day);
+	mon = BCD2BIN(mon);
+	year = BCD2BIN(year);
 
 	year += 1900;
 	if (year < 1970)
 		year += 100;
 
 	return mktime(year, mon, day, hour, min, sec);
+
+read_err:
+	dev_err(&save_client->dev, "m41t00_get_rtc_time: Read error\n");
+	return 0;
 }
+EXPORT_SYMBOL_GPL(m41t00_get_rtc_time);
 
 static void
 m41t00_set(void *arg)
 {
 	struct rtc_time	tm;
-	ulong	nowtime = *(ulong *)arg;
+	int nowtime = *(int *)arg;
+	s32 sec, min, hour, day, mon, year;
+	u8 wbuf[9], *buf = &wbuf[1], msgbuf[1] = { 0 };
+	struct i2c_msg msgs[] = {
+		{
+			.addr	= save_client->addr,
+			.flags	= 0,
+			.len	= 1,
+			.buf	= msgbuf,
+		},
+		{
+			.addr	= save_client->addr,
+			.flags	= I2C_M_RD,
+			.len	= 8,
+			.buf	= buf,
+		},
+	};
 
 	to_tm(nowtime, &tm);
 	tm.tm_year = (tm.tm_year - 1900) % 100;
 
-	BIN_TO_BCD(tm.tm_sec);
-	BIN_TO_BCD(tm.tm_min);
-	BIN_TO_BCD(tm.tm_hour);
-	BIN_TO_BCD(tm.tm_mon);
-	BIN_TO_BCD(tm.tm_mday);
-	BIN_TO_BCD(tm.tm_year);
-
-	mutex_lock(&m41t00_mutex);
-	if ((i2c_smbus_write_byte_data(save_client, 0, tm.tm_sec & 0x7f) < 0)
-		|| (i2c_smbus_write_byte_data(save_client, 1, tm.tm_min & 0x7f)
-			< 0)
-		|| (i2c_smbus_write_byte_data(save_client, 2, tm.tm_hour & 0x3f)
-			< 0)
-		|| (i2c_smbus_write_byte_data(save_client, 4, tm.tm_mday & 0x3f)
-			< 0)
-		|| (i2c_smbus_write_byte_data(save_client, 5, tm.tm_mon & 0x1f)
-			< 0)
-		|| (i2c_smbus_write_byte_data(save_client, 6, tm.tm_year & 0xff)
-			< 0))
-
-		dev_warn(&save_client->dev,"m41t00: can't write to rtc chip\n");
-
-	mutex_unlock(&m41t00_mutex);
-	return;
+	sec = BIN2BCD(tm.tm_sec);
+	min = BIN2BCD(tm.tm_min);
+	hour = BIN2BCD(tm.tm_hour);
+	day = BIN2BCD(tm.tm_mday);
+	mon = BIN2BCD(tm.tm_mon);
+	year = BIN2BCD(tm.tm_year);
+
+	/* Read reg values into buf[0..7]/wbuf[1..8] */
+	if (i2c_transfer(save_client->adapter, msgs, 2) < 0) {
+		dev_err(&save_client->dev, "m41t00_set: Read error\n");
+		return;
+	}
+
+	wbuf[0] = 0; /* offset into rtc's regs */
+	buf[m41t00_chip->sec] = (buf[m41t00_chip->sec] & ~0x7f) | (sec & 0x7f);
+	buf[m41t00_chip->min] = (buf[m41t00_chip->min] & ~0x7f) | (min & 0x7f);
+	buf[m41t00_chip->hour] = (buf[m41t00_chip->hour] & ~0x3f) | (hour& 0x3f);
+	buf[m41t00_chip->day] = (buf[m41t00_chip->day] & ~0x3f) | (day & 0x3f);
+	buf[m41t00_chip->mon] = (buf[m41t00_chip->mon] & ~0x1f) | (mon & 0x1f);
+
+	if (i2c_master_send(save_client, wbuf, 9) < 0)
+		dev_err(&save_client->dev, "m41t00_set: Write error\n");
 }
 
 static ulong new_time;
@@ -162,6 +230,48 @@ m41t00_set_rtc_time(ulong nowtime)
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(m41t00_set_rtc_time);
+
+/*
+ *****************************************************************************
+ *
+ *	platform_data Driver Interface
+ *
+ *****************************************************************************
+ */
+static int __init
+m41t00_platform_probe(struct platform_device *pdev)
+{
+	struct m41t00_platform_data *pdata;
+	int i;
+
+	if (pdev && (pdata = pdev->dev.platform_data)) {
+		normal_addr[0] = pdata->i2c_addr;
+
+		for (i=0; i<ARRAY_SIZE(m41t00_chip_info_tbl); i++)
+			if (m41t00_chip_info_tbl[i].type == pdata->type) {
+				m41t00_chip = &m41t00_chip_info_tbl[i];
+				m41t00_chip->sqw_freq = pdata->sqw_freq;
+				return 0;
+			}
+	}
+	return -ENODEV;
+}
+
+static int __exit
+m41t00_platform_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver m41t00_platform_driver = {
+	.probe  = m41t00_platform_probe,
+	.remove = m41t00_platform_remove,
+	.driver = {
+		.owner = THIS_MODULE,
+		.name  = M41T00_DRV_NAME,
+	},
+};
 
 /*
  *****************************************************************************
@@ -176,23 +286,71 @@ m41t00_probe(struct i2c_adapter *adap, int addr, int kind)
 	struct i2c_client *client;
 	int rc;
 
+	if (!i2c_check_functionality(adap, I2C_FUNC_I2C
+			| I2C_FUNC_SMBUS_BYTE_DATA))
+		return 0;
+
 	client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
 	if (!client)
 		return -ENOMEM;
 
-	strncpy(client->name, M41T00_DRV_NAME, I2C_NAME_SIZE);
+	strlcpy(client->name, m41t00_chip->name, I2C_NAME_SIZE);
 	client->addr = addr;
 	client->adapter = adap;
 	client->driver = &m41t00_driver;
 
-	if ((rc = i2c_attach_client(client)) != 0) {
-		kfree(client);
-		return rc;
+	if ((rc = i2c_attach_client(client)))
+		goto attach_err;
+
+	if (m41t00_chip->type != M41T00_TYPE_M41T00) {
+		/* If asked, disable SQW, set SQW frequency & re-enable */
+		if (m41t00_chip->sqw_freq)
+			if (((rc = i2c_smbus_read_byte_data(client,
+					m41t00_chip->alarm_mon)) < 0)
+			 || ((rc = i2c_smbus_write_byte_data(client,
+					m41t00_chip->alarm_mon, rc & ~0x40)) <0)
+			 || ((rc = i2c_smbus_write_byte_data(client,
+					m41t00_chip->sqw,
+					m41t00_chip->sqw_freq)) < 0)
+			 || ((rc = i2c_smbus_write_byte_data(client,
+					m41t00_chip->alarm_mon, rc | 0x40)) <0))
+				goto sqw_err;
+
+		/* Make sure HT (Halt Update) bit is cleared */
+		if ((rc = i2c_smbus_read_byte_data(client,
+				m41t00_chip->alarm_hour)) < 0)
+			goto ht_err;
+
+		if (rc & 0x40)
+			if ((rc = i2c_smbus_write_byte_data(client,
+					m41t00_chip->alarm_hour, rc & ~0x40))<0)
+				goto ht_err;
 	}
 
-	m41t00_wq = create_singlethread_workqueue("m41t00");
+	/* Make sure ST (stop) bit is cleared */
+	if ((rc = i2c_smbus_read_byte_data(client, m41t00_chip->sec)) < 0)
+		goto st_err;
+
+	if (rc & 0x80)
+		if ((rc = i2c_smbus_write_byte_data(client, m41t00_chip->sec,
+				rc & ~0x80)) < 0)
+			goto st_err;
+
+	m41t00_wq = create_singlethread_workqueue(m41t00_chip->name);
 	save_client = client;
 	return 0;
+
+st_err:
+	dev_err(&client->dev, "m41t00_probe: Can't clear ST bit\n");
+	goto attach_err;
+ht_err:
+	dev_err(&client->dev, "m41t00_probe: Can't clear HT bit\n");
+	goto attach_err;
+sqw_err:
+	dev_err(&client->dev, "m41t00_probe: Can't set SQW Frequency\n");
+attach_err:
+	kfree(client);
+	return rc;
 }
 
 static int
@@ -204,7 +362,7 @@ m41t00_attach(struct i2c_adapter *adap)
 static int
 m41t00_detach(struct i2c_client *client)
 {
-	int	rc;
+	int rc;
 
 	if ((rc = i2c_detach_client(client)) == 0) {
 		kfree(client);
@@ -225,14 +383,18 @@ static struct i2c_driver m41t00_driver = {
 static int __init
 m41t00_init(void)
 {
-	return i2c_add_driver(&m41t00_driver);
+	int rc;
+
+	if (!(rc = platform_driver_register(&m41t00_platform_driver)))
+		rc = i2c_add_driver(&m41t00_driver);
+	return rc;
 }
 
 static void __exit
 m41t00_exit(void)
 {
 	i2c_del_driver(&m41t00_driver);
-	return;
+	platform_driver_unregister(&m41t00_platform_driver);
 }
 
 module_init(m41t00_init);
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index 45e2cdf5473..a45155f799d 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -916,7 +916,7 @@ s32 i2c_smbus_write_word_data(struct i2c_client *client, u8 command, u16 value)
 }
 
 s32 i2c_smbus_write_block_data(struct i2c_client *client, u8 command,
-			       u8 length, u8 *values)
+			       u8 length, const u8 *values)
 {
 	union i2c_smbus_data data;
 
@@ -944,7 +944,7 @@ s32 i2c_smbus_read_i2c_block_data(struct i2c_client *client, u8 command, u8 *val
 }
 
 s32 i2c_smbus_write_i2c_block_data(struct i2c_client *client, u8 command,
-				   u8 length, u8 *values)
+				   u8 length, const u8 *values)
 {
 	union i2c_smbus_data data;
 
diff --git a/drivers/i2c/i2c-dev.c b/drivers/i2c/i2c-dev.c
index ed7eed388ba..58ccddd5c23 100644
--- a/drivers/i2c/i2c-dev.c
+++ b/drivers/i2c/i2c-dev.c
@@ -426,10 +426,7 @@ static int i2cdev_attach_adapter(struct i2c_adapter *adap)
 
 	/* register this i2c device with the driver core */
 	i2c_dev->adap = adap;
-	if (adap->dev.parent == &platform_bus)
-		dev = &adap->dev;
-	else
-		dev = adap->dev.parent;
+	dev = &adap->dev;
 	i2c_dev->class_dev = class_device_create(i2c_dev_class, NULL,
 						 MKDEV(I2C_MAJOR, i2c_dev->minor),
 						 dev, "i2c-%d", i2c_dev->minor);
diff --git a/include/linux/i2c-ocores.h b/include/linux/i2c-ocores.h
new file mode 100644
index 00000000000..8ed591b0887
--- /dev/null
+++ b/include/linux/i2c-ocores.h
@@ -0,0 +1,19 @@
+/*
+ * i2c-ocores.h - definitions for the i2c-ocores interface
+ *
+ * Peter Korsgaard <jacmet@sunsite.dk>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef _LINUX_I2C_OCORES_H
+#define _LINUX_I2C_OCORES_H
+
+struct ocores_i2c_platform_data {
+	u32 regstep;   /* distance between registers */
+	u32 clock_khz; /* input clock in kHz */
+};
+
+#endif /* _LINUX_I2C_OCORES_H */
diff --git a/include/linux/i2c.h b/include/linux/i2c.h
index 0510430e00d..526ddc8eecf 100644
--- a/include/linux/i2c.h
+++ b/include/linux/i2c.h
@@ -97,13 +97,13 @@ extern s32 i2c_smbus_write_word_data(struct i2c_client * client,
                                      u8 command, u16 value);
 extern s32 i2c_smbus_write_block_data(struct i2c_client * client,
 				      u8 command, u8 length,
-				      u8 *values);
+				      const u8 *values);
 /* Returns the number of read bytes */
 extern s32 i2c_smbus_read_i2c_block_data(struct i2c_client * client,
 					 u8 command, u8 *values);
 extern s32 i2c_smbus_write_i2c_block_data(struct i2c_client * client,
 					  u8 command, u8 length,
-					  u8 *values);
+					  const u8 *values);
 
 /*
  * A driver is capable of handling one or more physical devices present on
diff --git a/include/linux/m41t00.h b/include/linux/m41t00.h
new file mode 100644
index 00000000000..b423360ca38
--- /dev/null
+++ b/include/linux/m41t00.h
@@ -0,0 +1,50 @@
+/*
+ * Definitions for the ST M41T00 family of i2c rtc chips.
+ *
+ * Author: Mark A. Greer <mgreer@mvista.com>
+ *
+ * 2005, 2006 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#ifndef _M41T00_H
+#define _M41T00_H
+
+#define	M41T00_DRV_NAME		"m41t00"
+#define	M41T00_I2C_ADDR		0x68
+
+#define	M41T00_TYPE_M41T00	0
+#define	M41T00_TYPE_M41T81	81
+#define	M41T00_TYPE_M41T85	85
+
+struct m41t00_platform_data {
+	u8	type;
+	u8	i2c_addr;
+	u8	sqw_freq;
+};
+
+/* SQW output disabled, this is default value by power on */
+#define M41T00_SQW_DISABLE	(0)
+
+#define M41T00_SQW_32KHZ	(1<<4)		/* 32.768 KHz */
+#define M41T00_SQW_8KHZ		(2<<4)		/* 8.192 KHz */
+#define M41T00_SQW_4KHZ		(3<<4)		/* 4.096 KHz */
+#define M41T00_SQW_2KHZ		(4<<4)		/* 2.048 KHz */
+#define M41T00_SQW_1KHZ		(5<<4)		/* 1.024 KHz */
+#define M41T00_SQW_512HZ	(6<<4)		/* 512 Hz */
+#define M41T00_SQW_256HZ	(7<<4)		/* 256 Hz */
+#define M41T00_SQW_128HZ	(8<<4)		/* 128 Hz */
+#define M41T00_SQW_64HZ		(9<<4)		/* 64 Hz */
+#define M41T00_SQW_32HZ		(10<<4)		/* 32 Hz */
+#define M41T00_SQW_16HZ		(11<<4)		/* 16 Hz */
+#define M41T00_SQW_8HZ		(12<<4)		/* 8 Hz */
+#define M41T00_SQW_4HZ		(13<<4)		/* 4 Hz */
+#define M41T00_SQW_2HZ		(14<<4)		/* 2 Hz */
+#define M41T00_SQW_1HZ		(15<<4)		/* 1 Hz */
+
+extern ulong m41t00_get_rtc_time(void);
+extern int m41t00_set_rtc_time(ulong nowtime);
+
+#endif /* _M41T00_H */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index fd54a9d4c3d..cde701c13c7 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -352,8 +352,11 @@
 #define PCI_DEVICE_ID_ATI_RS480         0x5950
 /* ATI IXP Chipset */
 #define PCI_DEVICE_ID_ATI_IXP200_IDE	0x4349
+#define PCI_DEVICE_ID_ATI_IXP200_SMBUS	0x4353
+#define PCI_DEVICE_ID_ATI_IXP300_SMBUS	0x4363
 #define PCI_DEVICE_ID_ATI_IXP300_IDE	0x4369
 #define PCI_DEVICE_ID_ATI_IXP300_SATA   0x436e
+#define PCI_DEVICE_ID_ATI_IXP400_SMBUS	0x4372
 #define PCI_DEVICE_ID_ATI_IXP400_IDE	0x4376
 #define PCI_DEVICE_ID_ATI_IXP400_SATA   0x4379
 #define PCI_DEVICE_ID_ATI_IXP400_SATA2	0x437a
@@ -1133,9 +1136,11 @@
 #define PCI_DEVICE_ID_NVIDIA_QUADRO4_900XGL	0x0258
 #define PCI_DEVICE_ID_NVIDIA_QUADRO4_750XGL	0x0259
 #define PCI_DEVICE_ID_NVIDIA_QUADRO4_700XGL	0x025B
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SMBUS	0x0264
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE	0x0265
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA	0x0266
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_SATA2	0x0267
+#define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SMBUS	0x0368
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE	0x036E
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA	0x037E
 #define PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_SATA2	0x037F