diff options
author | Mark Brown <broonie@opensource.wolfsonmicro.com> | 2008-12-18 23:12:28 +0100 |
---|---|---|
committer | Samuel Ortiz <samuel@sortiz.org> | 2009-01-04 12:17:42 +0100 |
commit | ca23f8c1b0aa15dc69565244fc5dffa67a72dd02 (patch) | |
tree | ef082e834c225e8138f2c0a208a37b0384d4741f | |
parent | 645524a9c6e1e42dc4fe03217befb20e2fc4d43e (diff) |
mfd: Add WM8351 support
The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
-rw-r--r-- | drivers/mfd/Kconfig | 16 | ||||
-rw-r--r-- | drivers/mfd/wm8350-core.c | 47 | ||||
-rw-r--r-- | drivers/mfd/wm8350-i2c.c | 1 | ||||
-rw-r--r-- | drivers/mfd/wm8350-regmap.c | 1044 | ||||
-rw-r--r-- | include/linux/mfd/wm8350/core.h | 4 |
5 files changed, 1112 insertions, 0 deletions
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 76a482dfc17..781a27955ff 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -143,6 +143,22 @@ config MFD_WM8350_CONFIG_MODE_3 bool depends on MFD_WM8350 +config MFD_WM8351_CONFIG_MODE_0 + bool + depends on MFD_WM8350 + +config MFD_WM8351_CONFIG_MODE_1 + bool + depends on MFD_WM8350 + +config MFD_WM8351_CONFIG_MODE_2 + bool + depends on MFD_WM8350 + +config MFD_WM8351_CONFIG_MODE_3 + bool + depends on MFD_WM8350 + config MFD_WM8352_CONFIG_MODE_0 bool depends on MFD_WM8350 diff --git a/drivers/mfd/wm8350-core.c b/drivers/mfd/wm8350-core.c index 56c363c240a..e03fe60b55b 100644 --- a/drivers/mfd/wm8350-core.c +++ b/drivers/mfd/wm8350-core.c @@ -1169,6 +1169,36 @@ static int wm8350_create_cache(struct wm8350 *wm8350, int type, int mode) return -EINVAL; } + case 1: + switch (mode) { +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_0 + case 0: + reg_map = wm8351_mode0_defaults; + break; +#endif +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_1 + case 1: + reg_map = wm8351_mode1_defaults; + break; +#endif +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_2 + case 2: + reg_map = wm8351_mode2_defaults; + break; +#endif +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_3 + case 3: + reg_map = wm8351_mode3_defaults; + break; +#endif + default: + dev_err(wm8350->dev, + "WM8351 configuration mode %d not supported\n", + mode); + return -EINVAL; + } + break; + case 2: switch (mode) { #ifdef CONFIG_MFD_WM8352_CONFIG_MODE_0 @@ -1327,6 +1357,23 @@ int wm8350_device_init(struct wm8350 *wm8350, int irq, } break; + case 1: + wm8350->pmic.max_dcdc = WM8350_DCDC_4; + wm8350->pmic.max_isink = WM8350_ISINK_A; + + switch (chip_rev) { + case 0: + dev_info(wm8350->dev, "WM8351 Rev A\n"); + wm8350->power.rev_g_coeff = 1; + break; + + default: + dev_err(wm8350->dev, "Unknown WM8351 CHIP_REV\n"); + ret = -ENODEV; + goto err; + } + break; + case 2: wm8350->pmic.max_dcdc = WM8350_DCDC_6; wm8350->pmic.max_isink = WM8350_ISINK_B; diff --git a/drivers/mfd/wm8350-i2c.c b/drivers/mfd/wm8350-i2c.c index 87805125308..8d8c9321757 100644 --- a/drivers/mfd/wm8350-i2c.c +++ b/drivers/mfd/wm8350-i2c.c @@ -97,6 +97,7 @@ static int wm8350_i2c_remove(struct i2c_client *i2c) static const struct i2c_device_id wm8350_i2c_id[] = { { "wm8350", 0 }, + { "wm8351", 0 }, { "wm8352", 0 }, { } }; diff --git a/drivers/mfd/wm8350-regmap.c b/drivers/mfd/wm8350-regmap.c index 3e2cc37961f..68887b817d1 100644 --- a/drivers/mfd/wm8350-regmap.c +++ b/drivers/mfd/wm8350-regmap.c @@ -1074,6 +1074,1050 @@ const u16 wm8350_mode3_defaults[] = { }; #endif +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_0 + +#undef WM8350_HAVE_CONFIG_MODE +#define WM8350_HAVE_CONFIG_MODE + +const u16 wm8351_mode0_defaults[] = { + 0x6143, /* R0 - Reset/ID */ + 0x0000, /* R1 - ID */ + 0x0001, /* R2 - Revision */ + 0x1C02, /* R3 - System Control 1 */ + 0x0004, /* R4 - System Control 2 */ + 0x0000, /* R5 - System Hibernate */ + 0x8A00, /* R6 - Interface Control */ + 0x0000, /* R7 */ + 0x8000, /* R8 - Power mgmt (1) */ + 0x0000, /* R9 - Power mgmt (2) */ + 0x0000, /* R10 - Power mgmt (3) */ + 0x2000, /* R11 - Power mgmt (4) */ + 0x0E00, /* R12 - Power mgmt (5) */ + 0x0000, /* R13 - Power mgmt (6) */ + 0x0000, /* R14 - Power mgmt (7) */ + 0x0000, /* R15 */ + 0x0000, /* R16 - RTC Seconds/Minutes */ + 0x0100, /* R17 - RTC Hours/Day */ + 0x0101, /* R18 - RTC Date/Month */ + 0x1400, /* R19 - RTC Year */ + 0x0000, /* R20 - Alarm Seconds/Minutes */ + 0x0000, /* R21 - Alarm Hours/Day */ + 0x0000, /* R22 - Alarm Date/Month */ + 0x0320, /* R23 - RTC Time Control */ + 0x0000, /* R24 - System Interrupts */ + 0x0000, /* R25 - Interrupt Status 1 */ + 0x0000, /* R26 - Interrupt Status 2 */ + 0x0000, /* R27 */ + 0x0000, /* R28 - Under Voltage Interrupt status */ + 0x0000, /* R29 - Over Current Interrupt status */ + 0x0000, /* R30 - GPIO Interrupt Status */ + 0x0000, /* R31 - Comparator Interrupt Status */ + 0x3FFF, /* R32 - System Interrupts Mask */ + 0x0000, /* R33 - Interrupt Status 1 Mask */ + 0x0000, /* R34 - Interrupt Status 2 Mask */ + 0x0000, /* R35 */ + 0x0000, /* R36 - Under Voltage Interrupt status Mask */ + 0x0000, /* R37 - Over Current Interrupt status Mask */ + 0x0000, /* R38 - GPIO Interrupt Status Mask */ + 0x0000, /* R39 - Comparator Interrupt Status Mask */ + 0x0040, /* R40 - Clock Control 1 */ + 0x0000, /* R41 - Clock Control 2 */ + 0x3A00, /* R42 - FLL Control 1 */ + 0x7086, /* R43 - FLL Control 2 */ + 0xC226, /* R44 - FLL Control 3 */ + 0x0000, /* R45 - FLL Control 4 */ + 0x0000, /* R46 */ + 0x0000, /* R47 */ + 0x0000, /* R48 - DAC Control */ + 0x0000, /* R49 */ + 0x00C0, /* R50 - DAC Digital Volume L */ + 0x00C0, /* R51 - DAC Digital Volume R */ + 0x0000, /* R52 */ + 0x0040, /* R53 - DAC LR Rate */ + 0x0000, /* R54 - DAC Clock Control */ + 0x0000, /* R55 */ + 0x0000, /* R56 */ + 0x0000, /* R57 */ + 0x4000, /* R58 - DAC Mute */ + 0x0000, /* R59 - DAC Mute Volume */ + 0x0000, /* R60 - DAC Side */ + 0x0000, /* R61 */ + 0x0000, /* R62 */ + 0x0000, /* R63 */ + 0x8000, /* R64 - ADC Control */ + 0x0000, /* R65 */ + 0x00C0, /* R66 - ADC Digital Volume L */ + 0x00C0, /* R67 - ADC Digital Volume R */ + 0x0000, /* R68 - ADC Divider */ + 0x0000, /* R69 */ + 0x0040, /* R70 - ADC LR Rate */ + 0x0000, /* R71 */ + 0x0303, /* R72 - Input Control */ + 0x0000, /* R73 - IN3 Input Control */ + 0x0000, /* R74 - Mic Bias Control */ + 0x0000, /* R75 */ + 0x0000, /* R76 - Output Control */ + 0x0000, /* R77 - Jack Detect */ + 0x0000, /* R78 - Anti Pop Control */ + 0x0000, /* R79 */ + 0x0040, /* R80 - Left Input Volume */ + 0x0040, /* R81 - Right Input Volume */ + 0x0000, /* R82 */ + 0x0000, /* R83 */ + 0x0000, /* R84 */ + 0x0000, /* R85 */ + 0x0000, /* R86 */ + 0x0000, /* R87 */ + 0x0800, /* R88 - Left Mixer Control */ + 0x1000, /* R89 - Right Mixer Control */ + 0x0000, /* R90 */ + 0x0000, /* R91 */ + 0x0000, /* R92 - OUT3 Mixer Control */ + 0x0000, /* R93 - OUT4 Mixer Control */ + 0x0000, /* R94 */ + 0x0000, /* R95 */ + 0x0000, /* R96 - Output Left Mixer Volume */ + 0x0000, /* R97 - Output Right Mixer Volume */ + 0x0000, /* R98 - Input Mixer Volume L */ + 0x0000, /* R99 - Input Mixer Volume R */ + 0x0000, /* R100 - Input Mixer Volume */ + 0x0000, /* R101 */ + 0x0000, /* R102 */ + 0x0000, /* R103 */ + 0x00E4, /* R104 - OUT1L Volume */ + 0x00E4, /* R105 - OUT1R Volume */ + 0x00E4, /* R106 - OUT2L Volume */ + 0x02E4, /* R107 - OUT2R Volume */ + 0x0000, /* R108 */ + 0x0000, /* R109 */ + 0x0000, /* R110 */ + 0x0000, /* R111 - BEEP Volume */ + 0x0A00, /* R112 - AI Formating */ + 0x0000, /* R113 - ADC DAC COMP */ + 0x0020, /* R114 - AI ADC Control */ + 0x0020, /* R115 - AI DAC Control */ + 0x0000, /* R116 */ + 0x0000, /* R117 */ + 0x0000, /* R118 */ + 0x0000, /* R119 */ + 0x0000, /* R120 */ + 0x0000, /* R121 */ + 0x0000, /* R122 */ + 0x0000, /* R123 */ + 0x0000, /* R124 */ + 0x0000, /* R125 */ + 0x0000, /* R126 */ + 0x0000, /* R127 */ + 0x1FFF, /* R128 - GPIO Debounce */ + 0x0000, /* R129 - GPIO Pin pull up Control */ + 0x0000, /* R130 - GPIO Pull down Control */ + 0x0000, /* R131 - GPIO Interrupt Mode */ + 0x0000, /* R132 */ + 0x0000, /* R133 - GPIO Control */ + 0x0FFC, /* R134 - GPIO Configuration (i/o) */ + 0x0FFC, /* R135 - GPIO Pin Polarity / Type */ + 0x0000, /* R136 */ + 0x0000, /* R137 */ + 0x0000, /* R138 */ + 0x0000, /* R139 */ + 0x0013, /* R140 - GPIO Function Select 1 */ + 0x0000, /* R141 - GPIO Function Select 2 */ + 0x0000, /* R142 - GPIO Function Select 3 */ + 0x0003, /* R143 - GPIO Function Select 4 */ + 0x0000, /* R144 - Digitiser Control (1) */ + 0x0002, /* R145 - Digitiser Control (2) */ + 0x0000, /* R146 */ + 0x0000, /* R147 */ + 0x0000, /* R148 */ + 0x0000, /* R149 */ + 0x0000, /* R150 */ + 0x0000, /* R151 */ + 0x7000, /* R152 - AUX1 Readback */ + 0x7000, /* R153 - AUX2 Readback */ + 0x7000, /* R154 - AUX3 Readback */ + 0x7000, /* R155 - AUX4 Readback */ + 0x0000, /* R156 - USB Voltage Readback */ + 0x0000, /* R157 - LINE Voltage Readback */ + 0x0000, /* R158 - BATT Voltage Readback */ + 0x0000, /* R159 - Chip Temp Readback */ + 0x0000, /* R160 */ + 0x0000, /* R161 */ + 0x0000, /* R162 */ + 0x0000, /* R163 - Generic Comparator Control */ + 0x0000, /* R164 - Generic comparator 1 */ + 0x0000, /* R165 - Generic comparator 2 */ + 0x0000, /* R166 - Generic comparator 3 */ + 0x0000, /* R167 - Generic comparator 4 */ + 0xA00F, /* R168 - Battery Charger Control 1 */ + 0x0B06, /* R169 - Battery Charger Control 2 */ + 0x0000, /* R170 - Battery Charger Control 3 */ + 0x0000, /* R171 */ + 0x0000, /* R172 - Current Sink Driver A */ + 0x0000, /* R173 - CSA Flash control */ + 0x0000, /* R174 */ + 0x0000, /* R175 */ + 0x0000, /* R176 - DCDC/LDO requested */ + 0x032D, /* R177 - DCDC Active options */ + 0x0000, /* R178 - DCDC Sleep options */ + 0x0025, /* R179 - Power-check comparator */ + 0x000E, /* R180 - DCDC1 Control */ + 0x0000, /* R181 - DCDC1 Timeouts */ + 0x1006, /* R182 - DCDC1 Low Power */ + 0x0018, /* R183 - DCDC2 Control */ + 0x0000, /* R184 - DCDC2 Timeouts */ + 0x0000, /* R185 */ + 0x0000, /* R186 - DCDC3 Control */ + 0x0000, /* R187 - DCDC3 Timeouts */ + 0x0006, /* R188 - DCDC3 Low Power */ + 0x0000, /* R189 - DCDC4 Control */ + 0x0000, /* R190 - DCDC4 Timeouts */ + 0x0006, /* R191 - DCDC4 Low Power */ + 0x0008, /* R192 */ + 0x0000, /* R193 */ + 0x0000, /* R194 */ + 0x0000, /* R195 */ + 0x0000, /* R196 */ + 0x0006, /* R197 */ + 0x0000, /* R198 */ + 0x0003, /* R199 - Limit Switch Control */ + 0x001C, /* R200 - LDO1 Control */ + 0x0000, /* R201 - LDO1 Timeouts */ + 0x001C, /* R202 - LDO1 Low Power */ + 0x001B, /* R203 - LDO2 Control */ + 0x0000, /* R204 - LDO2 Timeouts */ + 0x001C, /* R205 - LDO2 Low Power */ + 0x001B, /* R206 - LDO3 Control */ + 0x0000, /* R207 - LDO3 Timeouts */ + 0x001C, /* R208 - LDO3 Low Power */ + 0x001B, /* R209 - LDO4 Control */ + 0x0000, /* R210 - LDO4 Timeouts */ + 0x001C, /* R211 - LDO4 Low Power */ + 0x0000, /* R212 */ + 0x0000, /* R213 */ + 0x0000, /* R214 */ + 0x0000, /* R215 - VCC_FAULT Masks */ + 0x001F, /* R216 - Main Bandgap Control */ + 0x0000, /* R217 - OSC Control */ + 0x9000, /* R218 - RTC Tick Control */ + 0x0000, /* R219 - Security1 */ + 0x4000, /* R220 */ + 0x0000, /* R221 */ + 0x0000, /* R222 */ + 0x0000, /* R223 */ + 0x0000, /* R224 - Signal overrides */ + 0x0000, /* R225 - DCDC/LDO status */ + 0x0000, /* R226 - Charger Overides/status */ + 0x0000, /* R227 - misc overrides */ + 0x0000, /* R228 - Supply overrides/status 1 */ + 0x0000, /* R229 - Supply overrides/status 2 */ + 0xE000, /* R230 - GPIO Pin Status */ + 0x0000, /* R231 - comparotor overrides */ + 0x0000, /* R232 */ + 0x0000, /* R233 - State Machine status */ + 0x1200, /* R234 - FLL Test 1 */ + 0x0000, /* R235 */ + 0x8000, /* R236 */ + 0x0000, /* R237 */ + 0x0000, /* R238 */ + 0x0000, /* R239 */ + 0x0003, /* R240 */ + 0x0000, /* R241 */ + 0x0000, /* R242 */ + 0x0004, /* R243 */ + 0x0300, /* R244 */ + 0x0000, /* R245 */ + 0x0200, /* R246 */ + 0x0000, /* R247 */ + 0x1000, /* R248 - DCDC1 Test Controls */ + 0x1000, /* R249 */ + 0x1000, /* R250 - DCDC3 Test Controls */ + 0x1000, /* R251 - DCDC4 Test Controls */ +}; +#endif + +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_1 + +#undef WM8350_HAVE_CONFIG_MODE +#define WM8350_HAVE_CONFIG_MODE + +const u16 wm8351_mode1_defaults[] = { + 0x6143, /* R0 - Reset/ID */ + 0x0000, /* R1 - ID */ + 0x0001, /* R2 - Revision */ + 0x1C02, /* R3 - System Control 1 */ + 0x0204, /* R4 - System Control 2 */ + 0x0000, /* R5 - System Hibernate */ + 0x8A00, /* R6 - Interface Control */ + 0x0000, /* R7 */ + 0x8000, /* R8 - Power mgmt (1) */ + 0x0000, /* R9 - Power mgmt (2) */ + 0x0000, /* R10 - Power mgmt (3) */ + 0x2000, /* R11 - Power mgmt (4) */ + 0x0E00, /* R12 - Power mgmt (5) */ + 0x0000, /* R13 - Power mgmt (6) */ + 0x0000, /* R14 - Power mgmt (7) */ + 0x0000, /* R15 */ + 0x0000, /* R16 - RTC Seconds/Minutes */ + 0x0100, /* R17 - RTC Hours/Day */ + 0x0101, /* R18 - RTC Date/Month */ + 0x1400, /* R19 - RTC Year */ + 0x0000, /* R20 - Alarm Seconds/Minutes */ + 0x0000, /* R21 - Alarm Hours/Day */ + 0x0000, /* R22 - Alarm Date/Month */ + 0x0320, /* R23 - RTC Time Control */ + 0x0000, /* R24 - System Interrupts */ + 0x0000, /* R25 - Interrupt Status 1 */ + 0x0000, /* R26 - Interrupt Status 2 */ + 0x0000, /* R27 */ + 0x0000, /* R28 - Under Voltage Interrupt status */ + 0x0000, /* R29 - Over Current Interrupt status */ + 0x0000, /* R30 - GPIO Interrupt Status */ + 0x0000, /* R31 - Comparator Interrupt Status */ + 0x3FFF, /* R32 - System Interrupts Mask */ + 0x0000, /* R33 - Interrupt Status 1 Mask */ + 0x0000, /* R34 - Interrupt Status 2 Mask */ + 0x0000, /* R35 */ + 0x0000, /* R36 - Under Voltage Interrupt status Mask */ + 0x0000, /* R37 - Over Current Interrupt status Mask */ + 0x0000, /* R38 - GPIO Interrupt Status Mask */ + 0x0000, /* R39 - Comparator Interrupt Status Mask */ + 0x0040, /* R40 - Clock Control 1 */ + 0x0000, /* R41 - Clock Control 2 */ + 0x3A00, /* R42 - FLL Control 1 */ + 0x7086, /* R43 - FLL Control 2 */ + 0xC226, /* R44 - FLL Control 3 */ + 0x0000, /* R45 - FLL Control 4 */ + 0x0000, /* R46 */ + 0x0000, /* R47 */ + 0x0000, /* R48 - DAC Control */ + 0x0000, /* R49 */ + 0x00C0, /* R50 - DAC Digital Volume L */ + 0x00C0, /* R51 - DAC Digital Volume R */ + 0x0000, /* R52 */ + 0x0040, /* R53 - DAC LR Rate */ + 0x0000, /* R54 - DAC Clock Control */ + 0x0000, /* R55 */ + 0x0000, /* R56 */ + 0x0000, /* R57 */ + 0x4000, /* R58 - DAC Mute */ + 0x0000, /* R59 - DAC Mute Volume */ + 0x0000, /* R60 - DAC Side */ + 0x0000, /* R61 */ + 0x0000, /* R62 */ + 0x0000, /* R63 */ + 0x8000, /* R64 - ADC Control */ + 0x0000, /* R65 */ + 0x00C0, /* R66 - ADC Digital Volume L */ + 0x00C0, /* R67 - ADC Digital Volume R */ + 0x0000, /* R68 - ADC Divider */ + 0x0000, /* R69 */ + 0x0040, /* R70 - ADC LR Rate */ + 0x0000, /* R71 */ + 0x0303, /* R72 - Input Control */ + 0x0000, /* R73 - IN3 Input Control */ + 0x0000, /* R74 - Mic Bias Control */ + 0x0000, /* R75 */ + 0x0000, /* R76 - Output Control */ + 0x0000, /* R77 - Jack Detect */ + 0x0000, /* R78 - Anti Pop Control */ + 0x0000, /* R79 */ + 0x0040, /* R80 - Left Input Volume */ + 0x0040, /* R81 - Right Input Volume */ + 0x0000, /* R82 */ + 0x0000, /* R83 */ + 0x0000, /* R84 */ + 0x0000, /* R85 */ + 0x0000, /* R86 */ + 0x0000, /* R87 */ + 0x0800, /* R88 - Left Mixer Control */ + 0x1000, /* R89 - Right Mixer Control */ + 0x0000, /* R90 */ + 0x0000, /* R91 */ + 0x0000, /* R92 - OUT3 Mixer Control */ + 0x0000, /* R93 - OUT4 Mixer Control */ + 0x0000, /* R94 */ + 0x0000, /* R95 */ + 0x0000, /* R96 - Output Left Mixer Volume */ + 0x0000, /* R97 - Output Right Mixer Volume */ + 0x0000, /* R98 - Input Mixer Volume L */ + 0x0000, /* R99 - Input Mixer Volume R */ + 0x0000, /* R100 - Input Mixer Volume */ + 0x0000, /* R101 */ + 0x0000, /* R102 */ + 0x0000, /* R103 */ + 0x00E4, /* R104 - OUT1L Volume */ + 0x00E4, /* R105 - OUT1R Volume */ + 0x00E4, /* R106 - OUT2L Volume */ + 0x02E4, /* R107 - OUT2R Volume */ + 0x0000, /* R108 */ + 0x0000, /* R109 */ + 0x0000, /* R110 */ + 0x0000, /* R111 - BEEP Volume */ + 0x0A00, /* R112 - AI Formating */ + 0x0000, /* R113 - ADC DAC COMP */ + 0x0020, /* R114 - AI ADC Control */ + 0x0020, /* R115 - AI DAC Control */ + 0x0000, /* R116 */ + 0x0000, /* R117 */ + 0x0000, /* R118 */ + 0x0000, /* R119 */ + 0x0000, /* R120 */ + 0x0000, /* R121 */ + 0x0000, /* R122 */ + 0x0000, /* R123 */ + 0x0000, /* R124 */ + 0x0000, /* R125 */ + 0x0000, /* R126 */ + 0x0000, /* R127 */ + 0x1FFF, /* R128 - GPIO Debounce */ + 0x0000, /* R129 - GPIO Pin pull up Control */ + 0x0000, /* R130 - GPIO Pull down Control */ + 0x0000, /* R131 - GPIO Interrupt Mode */ + 0x0000, /* R132 */ + 0x0000, /* R133 - GPIO Control */ + 0x0CFB, /* R134 - GPIO Configuration (i/o) */ + 0x0C1F, /* R135 - GPIO Pin Polarity / Type */ + 0x0000, /* R136 */ + 0x0000, /* R137 */ + 0x0000, /* R138 */ + 0x0000, /* R139 */ + 0x0300, /* R140 - GPIO Function Select 1 */ + 0x1110, /* R141 - GPIO Function Select 2 */ + 0x0013, /* R142 - GPIO Function Select 3 */ + 0x0003, /* R143 - GPIO Function Select 4 */ + 0x0000, /* R144 - Digitiser Control (1) */ + 0x0002, /* R145 - Digitiser Control (2) */ + 0x0000, /* R146 */ + 0x0000, /* R147 */ + 0x0000, /* R148 */ + 0x0000, /* R149 */ + 0x0000, /* R150 */ + 0x0000, /* R151 */ + 0x7000, /* R152 - AUX1 Readback */ + 0x7000, /* R153 - AUX2 Readback */ + 0x7000, /* R154 - AUX3 Readback */ + 0x7000, /* R155 - AUX4 Readback */ + 0x0000, /* R156 - USB Voltage Readback */ + 0x0000, /* R157 - LINE Voltage Readback */ + 0x0000, /* R158 - BATT Voltage Readback */ + 0x0000, /* R159 - Chip Temp Readback */ + 0x0000, /* R160 */ + 0x0000, /* R161 */ + 0x0000, /* R162 */ + 0x0000, /* R163 - Generic Comparator Control */ + 0x0000, /* R164 - Generic comparator 1 */ + 0x0000, /* R165 - Generic comparator 2 */ + 0x0000, /* R166 - Generic comparator 3 */ + 0x0000, /* R167 - Generic comparator 4 */ + 0xA00F, /* R168 - Battery Charger Control 1 */ + 0x0B06, /* R169 - Battery Charger Control 2 */ + 0x0000, /* R170 - Battery Charger Control 3 */ + 0x0000, /* R171 */ + 0x0000, /* R172 - Current Sink Driver A */ + 0x0000, /* R173 - CSA Flash control */ + 0x0000, /* R174 */ + 0x0000, /* R175 */ + 0x0000, /* R176 - DCDC/LDO requested */ + 0x032D, /* R177 - DCDC Active options */ + 0x0000, /* R178 - DCDC Sleep options */ + 0x0025, /* R179 - Power-check comparator */ + 0x000E, /* R180 - DCDC1 Control */ + 0x0C00, /* R181 - DCDC1 Timeouts */ + 0x1006, /* R182 - DCDC1 Low Power */ + 0x0018, /* R183 - DCDC2 Control */ + 0x0000, /* R184 - DCDC2 Timeouts */ + 0x0000, /* R185 */ + 0x0026, /* R186 - DCDC3 Control */ + 0x0400, /* R187 - DCDC3 Timeouts */ + 0x0006, /* R188 - DCDC3 Low Power */ + 0x0062, /* R189 - DCDC4 Control */ + 0x0800, /* R190 - DCDC4 Timeouts */ + 0x0006, /* R191 - DCDC4 Low Power */ + 0x0008, /* R192 */ + 0x0000, /* R193 */ + 0x0000, /* R194 */ + 0x000A, /* R195 */ + 0x1000, /* R196 */ + 0x0006, /* R197 */ + 0x0000, /* R198 */ + 0x0003, /* R199 - Limit Switch Control */ + 0x0006, /* R200 - LDO1 Control */ + 0x0000, /* R201 - LDO1 Timeouts */ + 0x001C, /* R202 - LDO1 Low Power */ + 0x0010, /* R203 - LDO2 Control */ + 0x0C00, /* R204 - LDO2 Timeouts */ + 0x001C, /* R205 - LDO2 Low Power */ + 0x001F, /* R206 - LDO3 Control */ + 0x0800, /* R207 - LDO3 Timeouts */ + 0x001C, /* R208 - LDO3 Low Power */ + 0x000A, /* R209 - LDO4 Control */ + 0x0800, /* R210 - LDO4 Timeouts */ + 0x001C, /* R211 - LDO4 Low Power */ + 0x0000, /* R212 */ + 0x0000, /* R213 */ + 0x0000, /* R214 */ + 0x0000, /* R215 - VCC_FAULT Masks */ + 0x001F, /* R216 - Main Bandgap Control */ + 0x0000, /* R217 - OSC Control */ + 0x9000, /* R218 - RTC Tick Control */ + 0x0000, /* R219 - Security1 */ + 0x4000, /* R220 */ + 0x0000, /* R221 */ + 0x0000, /* R222 */ + 0x0000, /* R223 */ + 0x0000, /* R224 - Signal overrides */ + 0x0000, /* R225 - DCDC/LDO status */ + 0x0000, /* R226 - Charger Overides/status */ + 0x0000, /* R227 - misc overrides */ + 0x0000, /* R228 - Supply overrides/status 1 */ + 0x0000, /* R229 - Supply overrides/status 2 */ + 0xE000, /* R230 - GPIO Pin Status */ + 0x0000, /* R231 - comparotor overrides */ + 0x0000, /* R232 */ + 0x0000, /* R233 - State Machine status */ + 0x1200, /* R234 - FLL Test 1 */ + 0x0000, /* R235 */ + 0x8000, /* R236 */ + 0x0000, /* R237 */ + 0x0000, /* R238 */ + 0x0000, /* R239 */ + 0x0003, /* R240 */ + 0x0000, /* R241 */ + 0x0000, /* R242 */ + 0x0004, /* R243 */ + 0x0300, /* R244 */ + 0x0000, /* R245 */ + 0x0200, /* R246 */ + 0x1000, /* R247 */ + 0x1000, /* R248 - DCDC1 Test Controls */ + 0x1000, /* R249 */ + 0x1000, /* R250 - DCDC3 Test Controls */ + 0x1000, /* R251 - DCDC4 Test Controls */ +}; +#endif + +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_2 + +#undef WM8350_HAVE_CONFIG_MODE +#define WM8350_HAVE_CONFIG_MODE + +const u16 wm8351_mode2_defaults[] = { + 0x6143, /* R0 - Reset/ID */ + 0x0000, /* R1 - ID */ + 0x0001, /* R2 - Revision */ + 0x1C02, /* R3 - System Control 1 */ + 0x0214, /* R4 - System Control 2 */ + 0x0000, /* R5 - System Hibernate */ + 0x8A00, /* R6 - Interface Control */ + 0x0000, /* R7 */ + 0x8000, /* R8 - Power mgmt (1) */ + 0x0000, /* R9 - Power mgmt (2) */ + 0x0000, /* R10 - Power mgmt (3) */ + 0x2000, /* R11 - Power mgmt (4) */ + 0x0E00, /* R12 - Power mgmt (5) */ + 0x0000, /* R13 - Power mgmt (6) */ + 0x0000, /* R14 - Power mgmt (7) */ + 0x0000, /* R15 */ + 0x0000, /* R16 - RTC Seconds/Minutes */ + 0x0100, /* R17 - RTC Hours/Day */ + 0x0101, /* R18 - RTC Date/Month */ + 0x1400, /* R19 - RTC Year */ + 0x0000, /* R20 - Alarm Seconds/Minutes */ + 0x0000, /* R21 - Alarm Hours/Day */ + 0x0000, /* R22 - Alarm Date/Month */ + 0x0320, /* R23 - RTC Time Control */ + 0x0000, /* R24 - System Interrupts */ + 0x0000, /* R25 - Interrupt Status 1 */ + 0x0000, /* R26 - Interrupt Status 2 */ + 0x0000, /* R27 */ + 0x0000, /* R28 - Under Voltage Interrupt status */ + 0x0000, /* R29 - Over Current Interrupt status */ + 0x0000, /* R30 - GPIO Interrupt Status */ + 0x0000, /* R31 - Comparator Interrupt Status */ + 0x3FFF, /* R32 - System Interrupts Mask */ + 0x0000, /* R33 - Interrupt Status 1 Mask */ + 0x0000, /* R34 - Interrupt Status 2 Mask */ + 0x0000, /* R35 */ + 0x0000, /* R36 - Under Voltage Interrupt status Mask */ + 0x0000, /* R37 - Over Current Interrupt status Mask */ + 0x0000, /* R38 - GPIO Interrupt Status Mask */ + 0x0000, /* R39 - Comparator Interrupt Status Mask */ + 0x0040, /* R40 - Clock Control 1 */ + 0x0000, /* R41 - Clock Control 2 */ + 0x3A00, /* R42 - FLL Control 1 */ + 0x7086, /* R43 - FLL Control 2 */ + 0xC226, /* R44 - FLL Control 3 */ + 0x0000, /* R45 - FLL Control 4 */ + 0x0000, /* R46 */ + 0x0000, /* R47 */ + 0x0000, /* R48 - DAC Control */ + 0x0000, /* R49 */ + 0x00C0, /* R50 - DAC Digital Volume L */ + 0x00C0, /* R51 - DAC Digital Volume R */ + 0x0000, /* R52 */ + 0x0040, /* R53 - DAC LR Rate */ + 0x0000, /* R54 - DAC Clock Control */ + 0x0000, /* R55 */ + 0x0000, /* R56 */ + 0x0000, /* R57 */ + 0x4000, /* R58 - DAC Mute */ + 0x0000, /* R59 - DAC Mute Volume */ + 0x0000, /* R60 - DAC Side */ + 0x0000, /* R61 */ + 0x0000, /* R62 */ + 0x0000, /* R63 */ + 0x8000, /* R64 - ADC Control */ + 0x0000, /* R65 */ + 0x00C0, /* R66 - ADC Digital Volume L */ + 0x00C0, /* R67 - ADC Digital Volume R */ + 0x0000, /* R68 - ADC Divider */ + 0x0000, /* R69 */ + 0x0040, /* R70 - ADC LR Rate */ + 0x0000, /* R71 */ + 0x0303, /* R72 - Input Control */ + 0x0000, /* R73 - IN3 Input Control */ + 0x0000, /* R74 - Mic Bias Control */ + 0x0000, /* R75 */ + 0x0000, /* R76 - Output Control */ + 0x0000, /* R77 - Jack Detect */ + 0x0000, /* R78 - Anti Pop Control */ + 0x0000, /* R79 */ + 0x0040, /* R80 - Left Input Volume */ + 0x0040, /* R81 - Right Input Volume */ + 0x0000, /* R82 */ + 0x0000, /* R83 */ + 0x0000, /* R84 */ + 0x0000, /* R85 */ + 0x0000, /* R86 */ + 0x0000, /* R87 */ + 0x0800, /* R88 - Left Mixer Control */ + 0x1000, /* R89 - Right Mixer Control */ + 0x0000, /* R90 */ + 0x0000, /* R91 */ + 0x0000, /* R92 - OUT3 Mixer Control */ + 0x0000, /* R93 - OUT4 Mixer Control */ + 0x0000, /* R94 */ + 0x0000, /* R95 */ + 0x0000, /* R96 - Output Left Mixer Volume */ + 0x0000, /* R97 - Output Right Mixer Volume */ + 0x0000, /* R98 - Input Mixer Volume L */ + 0x0000, /* R99 - Input Mixer Volume R */ + 0x0000, /* R100 - Input Mixer Volume */ + 0x0000, /* R101 */ + 0x0000, /* R102 */ + 0x0000, /* R103 */ + 0x00E4, /* R104 - OUT1L Volume */ + 0x00E4, /* R105 - OUT1R Volume */ + 0x00E4, /* R106 - OUT2L Volume */ + 0x02E4, /* R107 - OUT2R Volume */ + 0x0000, /* R108 */ + 0x0000, /* R109 */ + 0x0000, /* R110 */ + 0x0000, /* R111 - BEEP Volume */ + 0x0A00, /* R112 - AI Formating */ + 0x0000, /* R113 - ADC DAC COMP */ + 0x0020, /* R114 - AI ADC Control */ + 0x0020, /* R115 - AI DAC Control */ + 0x0000, /* R116 */ + 0x0000, /* R117 */ + 0x0000, /* R118 */ + 0x0000, /* R119 */ + 0x0000, /* R120 */ + 0x0000, /* R121 */ + 0x0000, /* R122 */ + 0x0000, /* R123 */ + 0x0000, /* R124 */ + 0x0000, /* R125 */ + 0x0000, /* R126 */ + 0x0000, /* R127 */ + 0x1FFF, /* R128 - GPIO Debounce */ + 0x0000, /* R129 - GPIO Pin pull up Control */ + 0x0110, /* R130 - GPIO Pull down Control */ + 0x0000, /* R131 - GPIO Interrupt Mode */ + 0x0000, /* R132 */ + 0x0000, /* R133 - GPIO Control */ + 0x09FA, /* R134 - GPIO Configuration (i/o) */ + 0x0DF6, /* R135 - GPIO Pin Polarity / Type */ + 0x0000, /* R136 */ + 0x0000, /* R137 */ + 0x0000, /* R138 */ + 0x0000, /* R139 */ + 0x1310, /* R140 - GPIO Function Select 1 */ + 0x0003, /* R141 - GPIO Function Select 2 */ + 0x2000, /* R142 - GPIO Function Select 3 */ + 0x0000, /* R143 - GPIO Function Select 4 */ + 0x0000, /* R144 - Digitiser Control (1) */ + 0x0002, /* R145 - Digitiser Control (2) */ + 0x0000, /* R146 */ + 0x0000, /* R147 */ + 0x0000, /* R148 */ + 0x0000, /* R149 */ + 0x0000, /* R150 */ + 0x0000, /* R151 */ + 0x7000, /* R152 - AUX1 Readback */ + 0x7000, /* R153 - AUX2 Readback */ + 0x7000, /* R154 - AUX3 Readback */ + 0x7000, /* R155 - AUX4 Readback */ + 0x0000, /* R156 - USB Voltage Readback */ + 0x0000, /* R157 - LINE Voltage Readback */ + 0x0000, /* R158 - BATT Voltage Readback */ + 0x0000, /* R159 - Chip Temp Readback */ + 0x0000, /* R160 */ + 0x0000, /* R161 */ + 0x0000, /* R162 */ + 0x0000, /* R163 - Generic Comparator Control */ + 0x0000, /* R164 - Generic comparator 1 */ + 0x0000, /* R165 - Generic comparator 2 */ + 0x0000, /* R166 - Generic comparator 3 */ + 0x0000, /* R167 - Generic comparator 4 */ + 0xA00F, /* R168 - Battery Charger Control 1 */ + 0x0B06, /* R169 - Battery Charger Control 2 */ + 0x0000, /* R170 - Battery Charger Control 3 */ + 0x0000, /* R171 */ + 0x0000, /* R172 - Current Sink Driver A */ + 0x0000, /* R173 - CSA Flash control */ + 0x0000, /* R174 */ + 0x0000, /* R175 */ + 0x0000, /* R176 - DCDC/LDO requested */ + 0x032D, /* R177 - DCDC Active options */ + 0x0000, /* R178 - DCDC Sleep options */ + 0x0025, /* R179 - Power-check comparator */ + 0x001A, /* R180 - DCDC1 Control */ + 0x0800, /* R181 - DCDC1 Timeouts */ + 0x1006, /* R182 - DCDC1 Low Power */ + 0x0018, /* R183 - DCDC2 Control */ + 0x0000, /* R184 - DCDC2 Timeouts */ + 0x0000, /* R185 */ + 0x0056, /* R186 - DCDC3 Control */ + 0x0400, /* R187 - DCDC3 Timeouts */ + 0x0006, /* R188 - DCDC3 Low Power */ + 0x0026, /* R189 - DCDC4 Control */ + 0x0C00, /* R190 - DCDC4 Timeouts */ + 0x0006, /* R191 - DCDC4 Low Power */ + 0x0008, /* R192 */ + 0x0000, /* R193 */ + 0x0000, /* R194 */ + 0x0026, /* R195 */ + 0x0C00, /* R196 */ + 0x0006, /* R197 */ + 0x0000, /* R198 */ + 0x0003, /* R199 - Limit Switch Control */ + 0x001C, /* R200 - LDO1 Control */ + 0x0400, /* R201 - LDO1 Timeouts */ + 0x001C, /* R202 - LDO1 Low Power */ + 0x0010, /* R203 - LDO2 Control */ + 0x0C00, /* R204 - LDO2 Timeouts */ + 0x001C, /* R205 - LDO2 Low Power */ + 0x0015, /* R206 - LDO3 Control */ + 0x0000, /* R207 - LDO3 Timeouts */ + 0x001C, /* R208 - LDO3 Low Power */ + 0x001A, /* R209 - LDO4 Control */ + 0x0000, /* R210 - LDO4 Timeouts */ + 0x001C, /* R211 - LDO4 Low Power */ + 0x0000, /* R212 */ + 0x0000, /* R213 */ + 0x0000, /* R214 */ + 0x0000, /* R215 - VCC_FAULT Masks */ + 0x001F, /* R216 - Main Bandgap Control */ + 0x0000, /* R217 - OSC Control */ + 0x9000, /* R218 - RTC Tick Control */ + 0x0000, /* R219 - Security1 */ + 0x4000, /* R220 */ + 0x0000, /* R221 */ + 0x0000, /* R222 */ + 0x0000, /* R223 */ + 0x0000, /* R224 - Signal overrides */ + 0x0000, /* R225 - DCDC/LDO status */ + 0x0000, /* R226 - Charger Overides/status */ + 0x0000, /* R227 - misc overrides */ + 0x0000, /* R228 - Supply overrides/status 1 */ + 0x0000, /* R229 - Supply overrides/status 2 */ + 0xE000, /* R230 - GPIO Pin Status */ + 0x0000, /* R231 - comparotor overrides */ + 0x0000, /* R232 */ + 0x0000, /* R233 - State Machine status */ + 0x1200, /* R234 - FLL Test 1 */ + 0x0000, /* R235 */ + 0x8000, /* R236 */ + 0x0000, /* R237 */ + 0x0000, /* R238 */ + 0x0000, /* R239 */ + 0x0003, /* R240 */ + 0x0000, /* R241 */ + 0x0000, /* R242 */ + 0x0004, /* R243 */ + 0x0300, /* R244 */ + 0x0000, /* R245 */ + 0x0200, /* R246 */ + 0x0000, /* R247 */ + 0x1000, /* R248 - DCDC1 Test Controls */ + 0x1000, /* R249 */ + 0x1000, /* R250 - DCDC3 Test Controls */ + 0x1000, /* R251 - DCDC4 Test Controls */ +}; +#endif + +#ifdef CONFIG_MFD_WM8351_CONFIG_MODE_3 + +#undef WM8350_HAVE_CONFIG_MODE +#define WM8350_HAVE_CONFIG_MODE + +const u16 wm8351_mode3_defaults[] = { + 0x6143, /* R0 - Reset/ID */ + 0x0000, /* R1 - ID */ + 0x0001, /* R2 - Revision */ + 0x1C02, /* R3 - System Control 1 */ + 0x0204, /* R4 - System Control 2 */ + 0x0000, /* R5 - System Hibernate */ + 0x8A00, /* R6 - Interface Control */ + 0x0000, /* R7 */ + 0x8000, /* R8 - Power mgmt (1) */ + 0x0000, /* R9 - Power mgmt (2) */ + 0x0000, /* R10 - Power mgmt (3) */ + 0x2000, /* R11 - Power mgmt (4) */ + 0x0E00, /* R12 - Power mgmt (5) */ + 0x0000, /* R13 - Power mgmt (6) */ + 0x0000, /* R14 - Power mgmt (7) */ + 0x0000, /* R15 */ + 0x0000, /* R16 - RTC Seconds/Minutes */ + 0x0100, /* R17 - RTC Hours/Day */ + 0x0101, /* R18 - RTC Date/Month */ + 0x1400, /* R19 - RTC Year */ + 0x0000, /* R20 - Alarm Seconds/Minutes */ + 0x0000, /* R21 - Alarm Hours/Day */ + 0x0000, /* R22 - Alarm Date/Month */ + 0x0320, /* R23 - RTC Time Control */ + 0x0000, /* R24 - System Interrupts */ + 0x0000, /* R25 - Interrupt Status 1 */ + 0x0000, /* R26 - Interrupt Status 2 */ + 0x0000, /* R27 */ + 0x0000, /* R28 - Under Voltage Interrupt status */ + 0x0000, /* R29 - Over Current Interrupt status */ + 0x0000, /* R30 - GPIO Interrupt Status */ + 0x0000, /* R31 - Comparator Interrupt Status */ + 0x3FFF, /* R32 - System Interrupts Mask */ + 0x0000, /* R33 - Interrupt Status 1 Mask */ + 0x0000, /* R34 - Interrupt Status 2 Mask */ + 0x0000, /* R35 */ + 0x0000, /* R36 - Under Voltage Interrupt status Mask */ + 0x0000, /* R37 - Over Current Interrupt status Mask */ + 0x0000, /* R38 - GPIO Interrupt Status Mask */ + 0x0000, /* R39 - Comparator Interrupt Status Mask */ + 0x0040, /* R40 - Clock Control 1 */ + 0x0000, /* R41 - Clock Control 2 */ + 0x3A00, /* R42 - FLL Control 1 */ + 0x7086, /* R43 - FLL Control 2 */ + 0xC226, /* R44 - FLL Control 3 */ + 0x0000, /* R45 - FLL Control 4 */ + 0x0000, /* R46 */ + 0x0000, /* R47 */ + 0x0000, /* R48 - DAC Control */ + 0x0000, /* R49 */ + 0x00C0, /* R50 - DAC Digital Volume L */ + 0x00C0, /* R51 - DAC Digital Volume R */ + 0x0000, /* R52 */ + 0x0040, /* R53 - DAC LR Rate */ + 0x0000, /* R54 - DAC Clock Control */ + 0x0000, /* R55 */ + 0x0000, /* R56 */ + 0x0000, /* R57 */ + 0x4000, /* R58 - DAC Mute */ + 0x0000, /* R59 - DAC Mute Volume */ + 0x0000, /* R60 - DAC Side */ + 0x0000, /* R61 */ + 0x0000, /* R62 */ + 0x0000, /* R63 */ + 0x8000, /* R64 - ADC Control */ + 0x0000, /* R65 */ + 0x00C0, /* R66 - ADC Digital Volume L */ + 0x00C0, /* R67 - ADC Digital Volume R */ + 0x0000, /* R68 - ADC Divider */ + 0x0000, /* R69 */ + 0x0040, /* R70 - ADC LR Rate */ + 0x0000, /* R71 */ + 0x0303, /* R72 - Input Control */ + 0x0000, /* R73 - IN3 Input Control */ + 0x0000, /* R74 - Mic Bias Control */ + 0x0000, /* R75 */ + 0x0000, /* R76 - Output Control */ + 0x0000, /* R77 - Jack Detect */ + 0x0000, /* R78 - Anti Pop Control */ + 0x0000, /* R79 */ + 0x0040, /* R80 - Left Input Volume */ + 0x0040, /* R81 - Right Input Volume */ + 0x0000, /* R82 */ + 0x0000, /* R83 */ + 0x0000, /* R84 */ + 0x0000, /* R85 */ + 0x0000, /* R86 */ + 0x0000, /* R87 */ + 0x0800, /* R88 - Left Mixer Control */ + 0x1000, /* R89 - Right Mixer Control */ + 0x0000, /* R90 */ + 0x0000, /* R91 */ + 0x0000, /* R92 - OUT3 Mixer Control */ + 0x0000, /* R93 - OUT4 Mixer Control */ + 0x0000, /* R94 */ + 0x0000, /* R95 */ + 0x0000, /* R96 - Output Left Mixer Volume */ + 0x0000, /* R97 - Output Right Mixer Volume */ + 0x0000, /* R98 - Input Mixer Volume L */ + 0x0000, /* R99 - Input Mixer Volume R */ + 0x0000, /* R100 - Input Mixer Volume */ + 0x0000, /* R101 */ + 0x0000, /* R102 */ + 0x0000, /* R103 */ + 0x00E4, /* R104 - OUT1L Volume */ + 0x00E4, /* R105 - OUT1R Volume */ + 0x00E4, /* R106 - OUT2L Volume */ + 0x02E4, /* R107 - OUT2R Volume */ + 0x0000, /* R108 */ + 0x0000, /* R109 */ + 0x0000, /* R110 */ + 0x0000, /* R111 - BEEP Volume */ + 0x0A00, /* R112 - AI Formating */ + 0x0000, /* R113 - ADC DAC COMP */ + 0x0020, /* R114 - AI ADC Control */ + 0x0020, /* R115 - AI DAC Control */ + 0x0000, /* R116 */ + 0x0000, /* R117 */ + 0x0000, /* R118 */ + 0x0000, /* R119 */ + 0x0000, /* R120 */ + 0x0000, /* R121 */ + 0x0000, /* R122 */ + 0x0000, /* R123 */ + 0x0000, /* R124 */ + 0x0000, /* R125 */ + 0x0000, /* R126 */ + 0x0000, /* R127 */ + 0x1FFF, /* R128 - GPIO Debounce */ + 0x0010, /* R129 - GPIO Pin pull up Control */ + 0x0000, /* R130 - GPIO Pull down Control */ + 0x0000, /* R131 - GPIO Interrupt Mode */ + 0x0000, /* R132 */ + 0x0000, /* R133 - GPIO Control */ + 0x0BFB, /* R134 - GPIO Configuration (i/o) */ + 0x0FFD, /* R135 - GPIO Pin Polarity / Type */ + 0x0000, /* R136 */ + 0x0000, /* R137 */ + 0x0000, /* R138 */ + 0x0000, /* R139 */ + 0x0310, /* R140 - GPIO Function Select 1 */ + 0x0001, /* R141 - GPIO Function Select 2 */ + 0x2300, /* R142 - GPIO Function Select 3 */ + 0x0003, /* R143 - GPIO Function Select 4 */ + 0x0000, /* R144 - Digitiser Control (1) */ + 0x0002, /* R145 - Digitiser Control (2) */ + 0x0000, /* R146 */ + 0x0000, /* R147 */ + 0x0000, /* R148 */ + 0x0000, /* R149 */ + 0x0000, /* R150 */ + 0x0000, /* R151 */ + 0x7000, /* R152 - AUX1 Readback */ + 0x7000, /* R153 - AUX2 Readback */ + 0x7000, /* R154 - AUX3 Readback */ + 0x7000, /* R155 - AUX4 Readback */ + 0x0000, /* R156 - USB Voltage Readback */ + 0x0000, /* R157 - LINE Voltage Readback */ + 0x0000, /* R158 - BATT Voltage Readback */ + 0x0000, /* R159 - Chip Temp Readback */ + 0x0000, /* R160 */ + 0x0000, /* R161 */ + 0x0000, /* R162 */ + 0x0000, /* R163 - Generic Comparator Control */ + 0x0000, /* R164 - Generic comparator 1 */ + 0x0000, /* R165 - Generic comparator 2 */ + 0x0000, /* R166 - Generic comparator 3 */ + 0x0000, /* R167 - Generic comparator 4 */ + 0xA00F, /* R168 - Battery Charger Control 1 */ + 0x0B06, /* R169 - Battery Charger Control 2 */ + 0x0000, /* R170 - Battery Charger Control 3 */ + 0x0000, /* R171 */ + 0x0000, /* R172 - Current Sink Driver A */ + 0x0000, /* R173 - CSA Flash control */ + 0x0000, /* R174 */ + 0x0000, /* R175 */ + 0x0000, /* R176 - DCDC/LDO requested */ + 0x032D, /* R177 - DCDC Active options */ + 0x0000, /* R178 - DCDC Sleep options */ + 0x0025, /* R179 - Power-check comparator */ + 0x000E, /* R180 - DCDC1 Control */ + 0x0400, /* R181 - DCDC1 Timeouts */ + 0x1006, /* R182 - DCDC1 Low Power */ + 0x0018, /* R183 - DCDC2 Control */ + 0x0000, /* R184 - DCDC2 Timeouts */ + 0x0000, /* R185 */ + 0x0026, /* R186 - DCDC3 Control */ + 0x0800, /* R187 - DCDC3 Timeouts */ + 0x0006, /* R188 - DCDC3 Low Power */ + 0x0062, /* R189 - DCDC4 Control */ + 0x1400, /* R190 - DCDC4 Timeouts */ + 0x0006, /* R191 - DCDC4 Low Power */ + 0x0008, /* R192 */ + 0x0000, /* R193 */ + 0x0000, /* R194 */ + 0x0026, /* R195 */ + 0x0400, /* R196 */ + 0x0006, /* R197 */ + 0x0000, /* R198 */ + 0x0003, /* R199 - Limit Switch Control */ + 0x0006, /* R200 - LDO1 Control */ + 0x0C00, /* R201 - LDO1 Timeouts */ + 0x001C, /* R202 - LDO1 Low Power */ + 0x0016, /* R203 - LDO2 Control */ + 0x0000, /* R204 - LDO2 Timeouts */ + 0x001C, /* R205 - LDO2 Low Power */ + 0x0019, /* R206 - LDO3 Control */ + 0x0000, /* R207 - LDO3 Timeouts */ + 0x001C, /* R208 - LDO3 Low Power */ + 0x001A, /* R209 - LDO4 Control */ + 0x1000, /* R210 - LDO4 Timeouts */ + 0x001C, /* R211 - LDO4 Low Power */ + 0x0000, /* R212 */ + 0x0000, /* R213 */ + 0x0000, /* R214 */ + 0x0000, /* R215 - VCC_FAULT Masks */ + 0x001F, /* R216 - Main Bandgap Control */ + 0x0000, /* R217 - OSC Control */ + 0x9000, /* R218 - RTC Tick Control */ + 0x0000, /* R219 - Security1 */ + 0x4000, /* R220 */ + 0x0000, /* R221 */ + 0x0000, /* R222 */ + 0x0000, /* R223 */ + 0x0000, /* R224 - Signal overrides */ + 0x0000, /* R225 - DCDC/LDO status */ + 0x0000, /* R226 - Charger Overides/status */ + 0x0000, /* R227 - misc overrides */ + 0x0000, /* R228 - Supply overrides/status 1 */ + 0x0000, /* R229 - Supply overrides/status 2 */ + 0xE000, /* R230 - GPIO Pin Status */ + 0x0000, /* R231 - comparotor overrides */ + 0x0000, /* R232 */ + 0x0000, /* R233 - State Machine status */ + 0x1200, /* R234 - FLL Test 1 */ + 0x0000, /* R235 */ + 0x8000, /* R236 */ + 0x0000, /* R237 */ + 0x0000, /* R238 */ + 0x0000, /* R239 */ + 0x0003, /* R240 */ + 0x0000, /* R241 */ + 0x0000, /* R242 */ + 0x0004, /* R243 */ + 0x0300, /* R244 */ + 0x0000, /* R245 */ + 0x0200, /* R246 */ + 0x0000, /* R247 */ + 0x1000, /* R248 - DCDC1 Test Controls */ + 0x1000, /* R249 */ + 0x1000, /* R250 - DCDC3 Test Controls */ + 0x1000, /* R251 - DCDC4 Test Controls */ +}; +#endif + #ifdef CONFIG_MFD_WM8352_CONFIG_MODE_0 #undef WM8350_HAVE_CONFIG_MODE diff --git a/include/linux/mfd/wm8350/core.h b/include/linux/mfd/wm8350/core.h index 737579086d0..980669d50dc 100644 --- a/include/linux/mfd/wm8350/core.h +++ b/include/linux/mfd/wm8350/core.h @@ -589,6 +589,10 @@ extern const u16 wm8350_mode0_defaults[]; extern const u16 wm8350_mode1_defaults[]; extern const u16 wm8350_mode2_defaults[]; extern const u16 wm8350_mode3_defaults[]; +extern const u16 wm8351_mode0_defaults[]; +extern const u16 wm8351_mode1_defaults[]; +extern const u16 wm8351_mode2_defaults[]; +extern const u16 wm8351_mode3_defaults[]; extern const u16 wm8352_mode0_defaults[]; extern const u16 wm8352_mode1_defaults[]; extern const u16 wm8352_mode2_defaults[]; |