[SERIAL] Remove obsoleted au1x00_uart driver

As announced in feature-removal-schedule.txt.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

5 files changed, 2 insertions, 1389 deletions

diff --git a/arch/mips/au1000/common/setup.c b/arch/mips/au1000/common/setup.c
index 1080558c810..307e98c29dd 100644
--- a/arch/mips/au1000/common/setup.c
+++ b/arch/mips/au1000/common/setup.c
@@ -94,7 +94,7 @@ void __init plat_setup(void)
 
 	argptr = prom_getcmdline();
 
-#if defined(CONFIG_SERIAL_AU1X00_CONSOLE) || defined(CONFIG_SERIAL_8250_CONSOLE)
+#ifdef CONFIG_SERIAL_8250_CONSOLE
 	if ((argptr = strstr(argptr, "console=")) == NULL) {
 		argptr = prom_getcmdline();
 		strcat(argptr, " console=ttyS0,115200");
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index ceb3697bf84..fe0d8b8e91c 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -620,22 +620,6 @@ config SERIAL_SH_SCI_CONSOLE
 	depends on SERIAL_SH_SCI=y
 	select SERIAL_CORE_CONSOLE
 
-config SERIAL_AU1X00
-	bool "Enable Au1x00 UART Support"
-	depends on MIPS && SOC_AU1X00
-	select SERIAL_CORE
-	help
-	  If you have an Alchemy AU1X00 processor (MIPS based) and you want
-	  to use serial ports, say Y.  Otherwise, say N.
-
-config SERIAL_AU1X00_CONSOLE
-	bool "Enable Au1x00 serial console"
-	depends on SERIAL_AU1X00
-	select SERIAL_CORE_CONSOLE
-	help
-	  If you have an Alchemy AU1X00 processor (MIPS based) and you want
-	  to use a console on a serial port, say Y.  Otherwise, say N.
-
 config SERIAL_CORE
 	tristate
 
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index a3a4323d9c8..d2b4c214876 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -41,7 +41,6 @@ obj-$(CONFIG_SERIAL_COLDFIRE) += mcfserial.o
 obj-$(CONFIG_V850E_UART) += v850e_uart.o
 obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
 obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o
-obj-$(CONFIG_SERIAL_AU1X00) += au1x00_uart.o
 obj-$(CONFIG_SERIAL_DZ) += dz.o
 obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o
 obj-$(CONFIG_SERIAL_SGI_L1_CONSOLE) += sn_console.o
diff --git a/drivers/serial/au1x00_uart.c b/drivers/serial/au1x00_uart.c
deleted file mode 100644
index 948880ac587..00000000000
--- a/drivers/serial/au1x00_uart.c
+++ /dev/null
@@ -1,1287 +0,0 @@
-/*
- *  Driver for 8250/16550-type serial ports
- *
- *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
- *
- *  Copyright (C) 2001 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * A note about mapbase / membase
- *
- *  mapbase is the physical address of the IO port.  Currently, we don't
- *  support this very well, and it may well be dropped from this driver
- *  in future.  As such, mapbase should be NULL.
- *
- *  membase is an 'ioremapped' cookie.  This is compatible with the old
- *  serial.c driver, and is currently the preferred form.
- */
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/tty.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/sysrq.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/delay.h>
-
-#include <asm/serial.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#if defined(CONFIG_SERIAL_AU1X00_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#include <linux/serial_core.h>
-#include "8250.h"
-
-/*
- * Debugging.
- */
-#if 0
-#define DEBUG_AUTOCONF(fmt...)	printk(fmt)
-#else
-#define DEBUG_AUTOCONF(fmt...)	do { } while (0)
-#endif
-
-#if 0
-#define DEBUG_INTR(fmt...)	printk(fmt)
-#else
-#define DEBUG_INTR(fmt...)	do { } while (0)
-#endif
-
-#define PASS_LIMIT	256
-
-/*
- * We default to IRQ0 for the "no irq" hack.   Some
- * machine types want others as well - they're free
- * to redefine this in their header file.
- */
-#define is_real_interrupt(irq)	((irq) != 0)
-
-static struct old_serial_port old_serial_port[] = {
-	{	.baud_base = 0,
-		.iomem_base = (u8 *)UART0_ADDR,
-		.irq = AU1000_UART0_INT,
-		.flags = STD_COM_FLAGS,
-		.iomem_reg_shift = 2,
-	}, {
-		.baud_base = 0,
-		.iomem_base = (u8 *)UART1_ADDR,
-		.irq = AU1000_UART1_INT,
-		.flags = STD_COM_FLAGS,
-		.iomem_reg_shift = 2
-	}, {
-		.baud_base = 0,
-		.iomem_base = (u8 *)UART2_ADDR,
-		.irq = AU1000_UART2_INT,
-		.flags = STD_COM_FLAGS,
-		.iomem_reg_shift = 2
-	}, {
-		.baud_base = 0,
-		.iomem_base = (u8 *)UART3_ADDR,
-		.irq = AU1000_UART3_INT,
-		.flags = STD_COM_FLAGS,
-		.iomem_reg_shift = 2
-	}
-};
-
-#define UART_NR	ARRAY_SIZE(old_serial_port)
-
-struct uart_8250_port {
-	struct uart_port	port;
-	struct timer_list	timer;		/* "no irq" timer */
-	struct list_head	list;		/* ports on this IRQ */
-	unsigned short		rev;
-	unsigned char		acr;
-	unsigned char		ier;
-	unsigned char		lcr;
-	unsigned char		mcr_mask;	/* mask of user bits */
-	unsigned char		mcr_force;	/* mask of forced bits */
-	unsigned char		lsr_break_flag;
-
-	/*
-	 * We provide a per-port pm hook.
-	 */
-	void			(*pm)(struct uart_port *port,
-				      unsigned int state, unsigned int old);
-};
-
-struct irq_info {
-	spinlock_t		lock;
-	struct list_head	*head;
-};
-
-static struct irq_info irq_lists[NR_IRQS];
-
-/*
- * Here we define the default xmit fifo size used for each type of UART.
- */
-static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
-	{ "unknown",	1,	0 },
-	{ "8250",	1,	0 },
-	{ "16450",	1,	0 },
-	{ "16550",	1,	0 },
-	/* PORT_16550A */
-	{ "AU1X00_UART",16,	UART_CLEAR_FIFO | UART_USE_FIFO },
-};
-
-static unsigned int serial_in(struct uart_8250_port *up, int offset)
-{
-	return au_readl((unsigned long)up->port.membase + offset);
-}
-
-static void serial_out(struct uart_8250_port *up, int offset, int value)
-{
-	au_writel(value, (unsigned long)up->port.membase + offset);
-}
-
-#define serial_inp(up, offset)		serial_in(up, offset)
-#define serial_outp(up, offset, value)	serial_out(up, offset, value)
-
-/*
- * This routine is called by rs_init() to initialize a specific serial
- * port.  It determines what type of UART chip this serial port is
- * using: 8250, 16450, 16550, 16550A.  The important question is
- * whether or not this UART is a 16550A or not, since this will
- * determine whether or not we can use its FIFO features or not.
- */
-static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
-{
-	unsigned char save_lcr, save_mcr;
-	unsigned long flags;
-
-	if (!up->port.iobase && !up->port.mapbase && !up->port.membase)
-		return;
-
-	DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04x, 0x%08lx): ",
-			up->port.line, up->port.iobase, up->port.membase);
-
-	/*
-	 * We really do need global IRQs disabled here - we're going to
-	 * be frobbing the chips IRQ enable register to see if it exists.
-	 */
-	spin_lock_irqsave(&up->port.lock, flags);
-//	save_flags(flags); cli();
-
-	save_mcr = serial_in(up, UART_MCR);
-	save_lcr = serial_in(up, UART_LCR);
-
-	up->port.type = PORT_16550A;
-	serial_outp(up, UART_LCR, save_lcr);
-
-	up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
-
-	if (up->port.type == PORT_UNKNOWN)
-		goto out;
-
-	/*
-	 * Reset the UART.
-	 */
-	serial_outp(up, UART_MCR, save_mcr);
-	serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
-				     UART_FCR_CLEAR_RCVR |
-				     UART_FCR_CLEAR_XMIT));
-	serial_outp(up, UART_FCR, 0);
-	(void)serial_in(up, UART_RX);
-	serial_outp(up, UART_IER, 0);
-
- out:	
-	spin_unlock_irqrestore(&up->port.lock, flags);
-//	restore_flags(flags);
-	DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
-}
-
-static void serial8250_stop_tx(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-
-	if (up->ier & UART_IER_THRI) {
-		up->ier &= ~UART_IER_THRI;
-		serial_out(up, UART_IER, up->ier);
-	}
-}
-
-static void serial8250_start_tx(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-
-	if (!(up->ier & UART_IER_THRI)) {
-		up->ier |= UART_IER_THRI;
-		serial_out(up, UART_IER, up->ier);
-	}
-}
-
-static void serial8250_stop_rx(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-
-	up->ier &= ~UART_IER_RLSI;
-	up->port.read_status_mask &= ~UART_LSR_DR;
-	serial_out(up, UART_IER, up->ier);
-}
-
-static void serial8250_enable_ms(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-
-	up->ier |= UART_IER_MSI;
-	serial_out(up, UART_IER, up->ier);
-}
-
-static void
-receive_chars(struct uart_8250_port *up, int *status, struct pt_regs *regs)
-{
-	struct tty_struct *tty = up->port.info->tty;
-	unsigned char ch, flag;
-	int max_count = 256;
-
-	do {
-		ch = serial_inp(up, UART_RX);
-		flag = TTY_NORMAL;
-		up->port.icount.rx++;
-
-		if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
-				       UART_LSR_FE | UART_LSR_OE))) {
-			/*
-			 * For statistics only
-			 */
-			if (*status & UART_LSR_BI) {
-				*status &= ~(UART_LSR_FE | UART_LSR_PE);
-				up->port.icount.brk++;
-				/*
-				 * We do the SysRQ and SAK checking
-				 * here because otherwise the break
-				 * may get masked by ignore_status_mask
-				 * or read_status_mask.
-				 */
-				if (uart_handle_break(&up->port))
-					goto ignore_char;
-			} else if (*status & UART_LSR_PE)
-				up->port.icount.parity++;
-			else if (*status & UART_LSR_FE)
-				up->port.icount.frame++;
-			if (*status & UART_LSR_OE)
-				up->port.icount.overrun++;
-
-			/*
-			 * Mask off conditions which should be ingored.
-			 */
-			*status &= up->port.read_status_mask;
-
-#ifdef CONFIG_SERIAL_AU1X00_CONSOLE
-			if (up->port.line == up->port.cons->index) {
-				/* Recover the break flag from console xmit */
-				*status |= up->lsr_break_flag;
-				up->lsr_break_flag = 0;
-			}
-#endif
-			if (*status & UART_LSR_BI) {
-				DEBUG_INTR("handling break....");
-				flag = TTY_BREAK;
-			} else if (*status & UART_LSR_PE)
-				flag = TTY_PARITY;
-			else if (*status & UART_LSR_FE)
-				flag = TTY_FRAME;
-		}
-		if (uart_handle_sysrq_char(&up->port, ch, regs))
-			goto ignore_char;
-		if ((*status & up->port.ignore_status_mask) == 0)
-			tty_insert_flip_char(tty, ch, flag);
-		if (*status & UART_LSR_OE)
-			/*
-			 * Overrun is special, since it's reported
-			 * immediately, and doesn't affect the current
-			 * character.
-			 */
-			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
-		}
-	ignore_char:
-		*status = serial_inp(up, UART_LSR);
-	} while ((*status & UART_LSR_DR) && (max_count-- > 0));
-	spin_unlock(&up->port.lock);
-	tty_flip_buffer_push(tty);
-	spin_lock(&up->port.lock);
-}
-
-static void transmit_chars(struct uart_8250_port *up)
-{
-	struct circ_buf *xmit = &up->port.info->xmit;
-	int count;
-
-	if (up->port.x_char) {
-		serial_outp(up, UART_TX, up->port.x_char);
-		up->port.icount.tx++;
-		up->port.x_char = 0;
-		return;
-	}
-	if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
-		serial8250_stop_tx(&up->port);
-		return;
-	}
-
-	count = up->port.fifosize;
-	do {
-		serial_out(up, UART_TX, xmit->buf[xmit->tail]);
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		up->port.icount.tx++;
-		if (uart_circ_empty(xmit))
-			break;
-	} while (--count > 0);
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(&up->port);
-
-	DEBUG_INTR("THRE...");
-
-	if (uart_circ_empty(xmit))
-		serial8250_stop_tx(&up->port);
-}
-
-static void check_modem_status(struct uart_8250_port *up)
-{
-	int status;
-
-	status = serial_in(up, UART_MSR);
-
-	if ((status & UART_MSR_ANY_DELTA) == 0)
-		return;
-
-	if (status & UART_MSR_TERI)
-		up->port.icount.rng++;
-	if (status & UART_MSR_DDSR)
-		up->port.icount.dsr++;
-	if (status & UART_MSR_DDCD)
-		uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
-	if (status & UART_MSR_DCTS)
-		uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
-
-	wake_up_interruptible(&up->port.info->delta_msr_wait);
-}
-
-/*
- * This handles the interrupt from one port.
- */
-static inline void
-serial8250_handle_port(struct uart_8250_port *up, struct pt_regs *regs)
-{
-	unsigned int status = serial_inp(up, UART_LSR);
-
-	DEBUG_INTR("status = %x...", status);
-
-	if (status & UART_LSR_DR)
-		receive_chars(up, &status, regs);
-	check_modem_status(up);
-	if (status & UART_LSR_THRE)
-		transmit_chars(up);
-}
-
-/*
- * This is the serial driver's interrupt routine.
- *
- * Arjan thinks the old way was overly complex, so it got simplified.
- * Alan disagrees, saying that need the complexity to handle the weird
- * nature of ISA shared interrupts.  (This is a special exception.)
- *
- * In order to handle ISA shared interrupts properly, we need to check
- * that all ports have been serviced, and therefore the ISA interrupt
- * line has been de-asserted.
- *
- * This means we need to loop through all ports. checking that they
- * don't have an interrupt pending.
- */
-static irqreturn_t serial8250_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
-	struct irq_info *i = dev_id;
-	struct list_head *l, *end = NULL;
-	int pass_counter = 0;
-
-	DEBUG_INTR("serial8250_interrupt(%d)...", irq);
-
-	spin_lock(&i->lock);
-
-	l = i->head;
-	do {
-		struct uart_8250_port *up;
-		unsigned int iir;
-
-		up = list_entry(l, struct uart_8250_port, list);
-
-		iir = serial_in(up, UART_IIR);
-		if (!(iir & UART_IIR_NO_INT)) {
-			spin_lock(&up->port.lock);
-			serial8250_handle_port(up, regs);
-			spin_unlock(&up->port.lock);
-
-			end = NULL;
-		} else if (end == NULL)
-			end = l;
-
-		l = l->next;
-
-		if (l == i->head && pass_counter++ > PASS_LIMIT) {
-			/* If we hit this, we're dead. */
-			printk(KERN_ERR "serial8250: too much work for "
-				"irq%d\n", irq);
-			break;
-		}
-	} while (l != end);
-
-	spin_unlock(&i->lock);
-
-	DEBUG_INTR("end.\n");
-	/* FIXME! Was it really ours? */
-	return IRQ_HANDLED;
-}
-
-/*
- * To support ISA shared interrupts, we need to have one interrupt
- * handler that ensures that the IRQ line has been deasserted
- * before returning.  Failing to do this will result in the IRQ
- * line being stuck active, and, since ISA irqs are edge triggered,
- * no more IRQs will be seen.
- */
-static void serial_do_unlink(struct irq_info *i, struct uart_8250_port *up)
-{
-	spin_lock_irq(&i->lock);
-
-	if (!list_empty(i->head)) {
-		if (i->head == &up->list)
-			i->head = i->head->next;
-		list_del(&up->list);
-	} else {
-		BUG_ON(i->head != &up->list);
-		i->head = NULL;
-	}
-
-	spin_unlock_irq(&i->lock);
-}
-
-static int serial_link_irq_chain(struct uart_8250_port *up)
-{
-	struct irq_info *i = irq_lists + up->port.irq;
-	int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? SA_SHIRQ : 0;
-
-	spin_lock_irq(&i->lock);
-
-	if (i->head) {
-		list_add(&up->list, i->head);
-		spin_unlock_irq(&i->lock);
-
-		ret = 0;
-	} else {
-		INIT_LIST_HEAD(&up->list);
-		i->head = &up->list;
-		spin_unlock_irq(&i->lock);
-
-		ret = request_irq(up->port.irq, serial8250_interrupt,
-				  irq_flags, "serial", i);
-		if (ret < 0)
-			serial_do_unlink(i, up);
-	}
-
-	return ret;
-}
-
-static void serial_unlink_irq_chain(struct uart_8250_port *up)
-{
-	struct irq_info *i = irq_lists + up->port.irq;
-
-	BUG_ON(i->head == NULL);
-
-	if (list_empty(i->head))
-		free_irq(up->port.irq, i);
-
-	serial_do_unlink(i, up);
-}
-
-/*
- * This function is used to handle ports that do not have an
- * interrupt.  This doesn't work very well for 16450's, but gives
- * barely passable results for a 16550A.  (Although at the expense
- * of much CPU overhead).
- */
-static void serial8250_timeout(unsigned long data)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)data;
-	unsigned int timeout;
-	unsigned int iir;
-
-	iir = serial_in(up, UART_IIR);
-	if (!(iir & UART_IIR_NO_INT)) {
-		spin_lock(&up->port.lock);
-		serial8250_handle_port(up, NULL);
-		spin_unlock(&up->port.lock);
-	}
-
-	timeout = up->port.timeout;
-	timeout = timeout > 6 ? (timeout / 2 - 2) : 1;
-	mod_timer(&up->timer, jiffies + timeout);
-}
-
-static unsigned int serial8250_tx_empty(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned long flags;
-	unsigned int ret;
-
-	spin_lock_irqsave(&up->port.lock, flags);
-	ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
-	spin_unlock_irqrestore(&up->port.lock, flags);
-
-	return ret;
-}
-
-static unsigned int serial8250_get_mctrl(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned char status;
-	unsigned int ret;
-
-	status = serial_in(up, UART_MSR);
-
-	ret = 0;
-	if (status & UART_MSR_DCD)
-		ret |= TIOCM_CAR;
-	if (status & UART_MSR_RI)
-		ret |= TIOCM_RNG;
-	if (status & UART_MSR_DSR)
-		ret |= TIOCM_DSR;
-	if (status & UART_MSR_CTS)
-		ret |= TIOCM_CTS;
-	return ret;
-}
-
-static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned char mcr = 0;
-
-	if (mctrl & TIOCM_RTS)
-		mcr |= UART_MCR_RTS;
-	if (mctrl & TIOCM_DTR)
-		mcr |= UART_MCR_DTR;
-	if (mctrl & TIOCM_OUT1)
-		mcr |= UART_MCR_OUT1;
-	if (mctrl & TIOCM_OUT2)
-		mcr |= UART_MCR_OUT2;
-	if (mctrl & TIOCM_LOOP)
-		mcr |= UART_MCR_LOOP;
-
-	mcr = (mcr & up->mcr_mask) | up->mcr_force;
-
-	serial_out(up, UART_MCR, mcr);
-}
-
-static void serial8250_break_ctl(struct uart_port *port, int break_state)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned long flags;
-
-	spin_lock_irqsave(&up->port.lock, flags);
-	if (break_state == -1)
-		up->lcr |= UART_LCR_SBC;
-	else
-		up->lcr &= ~UART_LCR_SBC;
-	serial_out(up, UART_LCR, up->lcr);
-	spin_unlock_irqrestore(&up->port.lock, flags);
-}
-
-static int serial8250_startup(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned long flags;
-	int retval;
-
-	/*
-	 * Clear the FIFO buffers and disable them.
-	 * (they will be reeanbled in set_termios())
-	 */
-	if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
-		serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
-		serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
-				UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
-		serial_outp(up, UART_FCR, 0);
-	}
-
-	/*
-	 * Clear the interrupt registers.
-	 */
-	(void) serial_inp(up, UART_LSR);
-	(void) serial_inp(up, UART_RX);
-	(void) serial_inp(up, UART_IIR);
-	(void) serial_inp(up, UART_MSR);
-
-	/*
-	 * At this point, there's no way the LSR could still be 0xff;
-	 * if it is, then bail out, because there's likely no UART
-	 * here.
-	 */
-	if (!(up->port.flags & UPF_BUGGY_UART) &&
-	    (serial_inp(up, UART_LSR) == 0xff)) {
-		printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
-		return -ENODEV;
-	}
-
-	retval = serial_link_irq_chain(up);
-		if (retval)
-			return retval;
-
-	/*
-	 * Now, initialize the UART
-	 */
-	serial_outp(up, UART_LCR, UART_LCR_WLEN8);
-
-	spin_lock_irqsave(&up->port.lock, flags);
-	if (up->port.flags & UPF_FOURPORT) {
-		if (!is_real_interrupt(up->port.irq))
-			up->port.mctrl |= TIOCM_OUT1;
-	} else
-		/*
-		 * Most PC uarts need OUT2 raised to enable interrupts.
-		 */
-		if (is_real_interrupt(up->port.irq))
-			up->port.mctrl |= TIOCM_OUT2;
-
-	serial8250_set_mctrl(&up->port, up->port.mctrl);
-	spin_unlock_irqrestore(&up->port.lock, flags);
-
-	/*
-	 * Finally, enable interrupts.  Note: Modem status interrupts
-	 * are set via set_termios(), which will be occurring imminently
-	 * anyway, so we don't enable them here.
-	 */
-	up->ier = UART_IER_RLSI | UART_IER_RDI;
-	serial_outp(up, UART_IER, up->ier);
-
-	if (up->port.flags & UPF_FOURPORT) {
-		unsigned int icp;
-		/*
-		 * Enable interrupts on the AST Fourport board
-		 */
-		icp = (up->port.iobase & 0xfe0) | 0x01f;
-		outb_p(0x80, icp);
-		(void) inb_p(icp);
-	}
-
-	/*
-	 * And clear the interrupt registers again for luck.
-	 */
-	(void) serial_inp(up, UART_LSR);
-	(void) serial_inp(up, UART_RX);
-	(void) serial_inp(up, UART_IIR);
-	(void) serial_inp(up, UART_MSR);
-
-	return 0;
-}
-
-static void serial8250_shutdown(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned long flags;
-
-	/*
-	 * Disable interrupts from this port
-	 */
-	up->ier = 0;
-	serial_outp(up, UART_IER, 0);
-
-	spin_lock_irqsave(&up->port.lock, flags);
-	if (up->port.flags & UPF_FOURPORT) {
-		/* reset interrupts on the AST Fourport board */
-		inb((up->port.iobase & 0xfe0) | 0x1f);
-		up->port.mctrl |= TIOCM_OUT1;
-	} else
-		up->port.mctrl &= ~TIOCM_OUT2;
-
-	serial8250_set_mctrl(&up->port, up->port.mctrl);
-	spin_unlock_irqrestore(&up->port.lock, flags);
-
-	/*
-	 * Disable break condition and FIFOs
-	 */
-	serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
-	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
-				  UART_FCR_CLEAR_RCVR |
-				  UART_FCR_CLEAR_XMIT);
-	serial_outp(up, UART_FCR, 0);
-
-	/*
-	 * Read data port to reset things, and then unlink from
-	 * the IRQ chain.
-	 */
-	(void) serial_in(up, UART_RX);
-
-	if (!is_real_interrupt(up->port.irq))
-		del_timer_sync(&up->timer);
-	else
-		serial_unlink_irq_chain(up);
-}
-
-static unsigned int serial8250_get_divisor(struct uart_port *port, unsigned int baud)
-{
-	unsigned int quot;
-
-	/*
-	 * Handle magic divisors for baud rates above baud_base on
-	 * SMSC SuperIO chips.
-	 */
-	if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
-	    baud == (port->uartclk/4))
-		quot = 0x8001;
-	else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
-		 baud == (port->uartclk/8))
-		quot = 0x8002;
-	else
-		quot = uart_get_divisor(port, baud);
-
-	return quot;
-}
-
-static void
-serial8250_set_termios(struct uart_port *port, struct termios *termios,
-		       struct termios *old)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned char cval, fcr = 0;
-	unsigned long flags;
-	unsigned int baud, quot;
-
-	switch (termios->c_cflag & CSIZE) {
-	case CS5:
-		cval = UART_LCR_WLEN5;
-		break;
-	case CS6:
-		cval = UART_LCR_WLEN6;
-		break;
-	case CS7:
-		cval = UART_LCR_WLEN7;
-		break;
-	default:
-	case CS8:
-		cval = UART_LCR_WLEN8;
-		break;
-	}
-
-	if (termios->c_cflag & CSTOPB)
-		cval |= UART_LCR_STOP;
-	if (termios->c_cflag & PARENB)
-		cval |= UART_LCR_PARITY;
-	if (!(termios->c_cflag & PARODD))
-		cval |= UART_LCR_EPAR;
-#ifdef CMSPAR
-	if (termios->c_cflag & CMSPAR)
-		cval |= UART_LCR_SPAR;
-#endif
-
-	/*
-	 * Ask the core to calculate the divisor for us.
-	 */
-	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
-	quot = serial8250_get_divisor(port, baud);
-	quot = 0x35; /* FIXME */
-
-	/*
-	 * Work around a bug in the Oxford Semiconductor 952 rev B
-	 * chip which causes it to seriously miscalculate baud rates
-	 * when DLL is 0.
-	 */
-	if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
-	    up->rev == 0x5201)
-		quot ++;
-
-	if (uart_config[up->port.type].flags & UART_USE_FIFO) {
-		if (baud < 2400)
-			fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIGGER_1;
-		else
-			fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIGGER_8;
-	}
-
-	/*
-	 * Ok, we're now changing the port state.  Do it with
-	 * interrupts disabled.
-	 */
-	spin_lock_irqsave(&up->port.lock, flags);
-
-	/*
-	 * Update the per-port timeout.
-	 */
-	uart_update_timeout(port, termios->c_cflag, baud);
-
-	up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
-	if (termios->c_iflag & INPCK)
-		up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
-	if (termios->c_iflag & (BRKINT | PARMRK))
-		up->port.read_status_mask |= UART_LSR_BI;
-
-	/*
-	 * Characteres to ignore
-	 */
-	up->port.ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
-	if (termios->c_iflag & IGNBRK) {
-		up->port.ignore_status_mask |= UART_LSR_BI;
-		/*
-		 * If we're ignoring parity and break indicators,
-		 * ignore overruns too (for real raw support).
-		 */
-		if (termios->c_iflag & IGNPAR)
-			up->port.ignore_status_mask |= UART_LSR_OE;
-	}
-
-	/*
-	 * ignore all characters if CREAD is not set
-	 */
-	if ((termios->c_cflag & CREAD) == 0)
-		up->port.ignore_status_mask |= UART_LSR_DR;
-
-	/*
-	 * CTS flow control flag and modem status interrupts
-	 */
-	up->ier &= ~UART_IER_MSI;
-	if (UART_ENABLE_MS(&up->port, termios->c_cflag))
-		up->ier |= UART_IER_MSI;
-
-	serial_out(up, UART_IER, up->ier);
-	serial_outp(up, 0x28, quot & 0xffff);
-	up->lcr = cval;					/* Save LCR */
-	if (up->port.type != PORT_16750) {
-		if (fcr & UART_FCR_ENABLE_FIFO) {
-			/* emulated UARTs (Lucent Venus 167x) need two steps */
-			serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
-		}
-		serial_outp(up, UART_FCR, fcr);		/* set fcr */
-	}
-	spin_unlock_irqrestore(&up->port.lock, flags);
-}
-
-static void
-serial8250_pm(struct uart_port *port, unsigned int state,
-	      unsigned int oldstate)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	if (state) {
-		/* sleep */
-		if (up->pm)
-			up->pm(port, state, oldstate);
-	} else {
-		/* wake */
-		if (up->pm)
-			up->pm(port, state, oldstate);
-	}
-}
-
-/*
- * Resource handling.  This is complicated by the fact that resources
- * depend on the port type.  Maybe we should be claiming the standard
- * 8250 ports, and then trying to get other resources as necessary?
- */
-static int
-serial8250_request_std_resource(struct uart_8250_port *up, struct resource **res)
-{
-	unsigned int size = 8 << up->port.regshift;
-	int ret = 0;
-
-	switch (up->port.iotype) {
-	case UPIO_MEM:
-		if (up->port.mapbase) {
-			*res = request_mem_region(up->port.mapbase, size, "serial");
-			if (!*res)
-				ret = -EBUSY;
-		}
-		break;
-
-	case UPIO_HUB6:
-	case UPIO_PORT:
-		*res = request_region(up->port.iobase, size, "serial");
-		if (!*res)
-			ret = -EBUSY;
-		break;
-	}
-	return ret;
-}
-
-
-static void serial8250_release_port(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned long start, offset = 0, size = 0;
-
-	size <<= up->port.regshift;
-
-	switch (up->port.iotype) {
-	case UPIO_MEM:
-		if (up->port.mapbase) {
-			/*
-			 * Unmap the area.
-			 */
-			iounmap(up->port.membase);
-			up->port.membase = NULL;
-
-			start = up->port.mapbase;
-
-			if (size)
-				release_mem_region(start + offset, size);
-			release_mem_region(start, 8 << up->port.regshift);
-		}
-		break;
-
-	case UPIO_HUB6:
-	case UPIO_PORT:
-		start = up->port.iobase;
-
-		if (size)
-			release_region(start + offset, size);
-		release_region(start + offset, 8 << up->port.regshift);
-		break;
-
-	default:
-		break;
-	}
-}
-
-static int serial8250_request_port(struct uart_port *port)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	struct resource *res = NULL, *res_rsa = NULL;
-	int ret = 0;
-
-	ret = serial8250_request_std_resource(up, &res);
-
-	/*
-	 * If we have a mapbase, then request that as well.
-	 */
-	if (ret == 0 && up->port.flags & UPF_IOREMAP) {
-		int size = res->end - res->start + 1;
-
-		up->port.membase = ioremap(up->port.mapbase, size);
-		if (!up->port.membase)
-			ret = -ENOMEM;
-	}
-
-	if (ret < 0) {
-		if (res_rsa)
-			release_resource(res_rsa);
-		if (res)
-			release_resource(res);
-	}
-	return ret;
-}
-
-static void serial8250_config_port(struct uart_port *port, int flags)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	struct resource *res_std = NULL, *res_rsa = NULL;
-	int probeflags = PROBE_ANY;
-
-	probeflags &= ~PROBE_RSA;
-
-	if (flags & UART_CONFIG_TYPE)
-		autoconfig(up, probeflags);
-
-	/*
-	 * If the port wasn't an RSA port, release the resource.
-	 */
-	if (up->port.type != PORT_RSA && res_rsa)
-		release_resource(res_rsa);
-
-	if (up->port.type == PORT_UNKNOWN && res_std)
-		release_resource(res_std);
-}
-
-static int
-serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
-{
-	if (ser->irq >= NR_IRQS || ser->irq < 0 ||
-	    ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
-	    ser->type > PORT_MAX_8250 || ser->type == PORT_CIRRUS ||
-	    ser->type == PORT_STARTECH)
-		return -EINVAL;
-	return 0;
-}
-
-static const char *
-serial8250_type(struct uart_port *port)
-{
-	int type = port->type;
-
-	if (type >= ARRAY_SIZE(uart_config))
-		type = 0;
-	return uart_config[type].name;
-}
-
-static struct uart_ops serial8250_pops = {
-	.tx_empty	= serial8250_tx_empty,
-	.set_mctrl	= serial8250_set_mctrl,
-	.get_mctrl	= serial8250_get_mctrl,
-	.stop_tx	= serial8250_stop_tx,
-	.start_tx	= serial8250_start_tx,
-	.stop_rx	= serial8250_stop_rx,
-	.enable_ms	= serial8250_enable_ms,
-	.break_ctl	= serial8250_break_ctl,
-	.startup	= serial8250_startup,
-	.shutdown	= serial8250_shutdown,
-	.set_termios	= serial8250_set_termios,
-	.pm		= serial8250_pm,
-	.type		= serial8250_type,
-	.release_port	= serial8250_release_port,
-	.request_port	= serial8250_request_port,
-	.config_port	= serial8250_config_port,
-	.verify_port	= serial8250_verify_port,
-};
-
-static struct uart_8250_port serial8250_ports[UART_NR];
-
-static void __init serial8250_isa_init_ports(void)
-{
-	struct uart_8250_port *up;
-	static int first = 1;
-	int i;
-
-	if (!first)
-		return;
-	first = 0;
-
-	for (i = 0, up = serial8250_ports; i < ARRAY_SIZE(old_serial_port);
-	     i++, up++) {
-		up->port.iobase   = old_serial_port[i].port;
-		up->port.irq      = old_serial_port[i].irq;
-		up->port.uartclk  = get_au1x00_uart_baud_base();
-		up->port.flags    = old_serial_port[i].flags;
-		up->port.hub6     = old_serial_port[i].hub6;
-		up->port.membase  = old_serial_port[i].iomem_base;
-		up->port.iotype   = old_serial_port[i].io_type;
-		up->port.regshift = old_serial_port[i].iomem_reg_shift;
-		up->port.ops      = &serial8250_pops;
-	}
-}
-
-static void __init serial8250_register_ports(struct uart_driver *drv)
-{
-	int i;
-
-	serial8250_isa_init_ports();
-
-	for (i = 0; i < UART_NR; i++) {
-		struct uart_8250_port *up = &serial8250_ports[i];
-
-		up->port.line = i;
-		up->port.ops = &serial8250_pops;
-		init_timer(&up->timer);
-		up->timer.function = serial8250_timeout;
-
-		/*
-		 * ALPHA_KLUDGE_MCR needs to be killed.
-		 */
-		up->mcr_mask = ~ALPHA_KLUDGE_MCR;
-		up->mcr_force = ALPHA_KLUDGE_MCR;
-
-		uart_add_one_port(drv, &up->port);
-	}
-}
-
-#ifdef CONFIG_SERIAL_AU1X00_CONSOLE
-
-#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
-
-/*
- *	Wait for transmitter & holding register to empty
- */
-static inline void wait_for_xmitr(struct uart_8250_port *up)
-{
-	unsigned int status, tmout = 10000;
-
-	/* Wait up to 10ms for the character(s) to be sent. */
-	do {
-		status = serial_in(up, UART_LSR);
-
-		if (status & UART_LSR_BI)
-			up->lsr_break_flag = UART_LSR_BI;
-
-		if (--tmout == 0)
-			break;
-		udelay(1);
-	} while ((status & BOTH_EMPTY) != BOTH_EMPTY);
-
-	/* Wait up to 1s for flow control if necessary */
-	if (up->port.flags & UPF_CONS_FLOW) {
-		tmout = 1000000;
-		while (--tmout &&
-		       ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
-			udelay(1);
-	}
-}
-
-static void au1x00_console_putchar(struct uart_port *port, int ch)
-{
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
-
-	wait_for_xmitr(up);
-	serial_out(up, UART_TX, ch);
-}
-
-/*
- *	Print a string to the serial port trying not to disturb
- *	any possible real use of the port...
- *
- *	The console_lock must be held when we get here.
- */
-static void
-serial8250_console_write(struct console *co, const char *s, unsigned int count)
-{
-	struct uart_8250_port *up = &serial8250_ports[co->index];
-	unsigned int ier;
-
-	/*
-	 *	First save the UER then disable the interrupts
-	 */
-	ier = serial_in(up, UART_IER);
-	serial_out(up, UART_IER, 0);
-
-	uart_console_write(&up->port, s, count, au1x00_console_putchar);
-
-	/*
-	 *	Finally, wait for transmitter to become empty
-	 *	and restore the IER
-	 */
-	wait_for_xmitr(up);
-	serial_out(up, UART_IER, ier);
-}
-
-static int __init serial8250_console_setup(struct console *co, char *options)
-{
-	struct uart_port *port;
-	int baud = 9600;
-	int bits = 8;
-	int parity = 'n';
-	int flow = 'n';
-
-	/*
-	 * Check whether an invalid uart number has been specified, and
-	 * if so, search for the first available port that does have
-	 * console support.
-	 */
-	if (co->index >= UART_NR)
-		co->index = 0;
-	port = &serial8250_ports[co->index].port;
-
-	/*
-	 * Temporary fix.
-	 */
-	spin_lock_init(&port->lock);
-
-	if (options)
-		uart_parse_options(options, &baud, &parity, &bits, &flow);
-
-	return uart_set_options(port, co, baud, parity, bits, flow);
-}
-
-extern struct uart_driver serial8250_reg;
-static struct console serial8250_console = {
-	.name		= "ttyS",
-	.write		= serial8250_console_write,
-	.device		= uart_console_device,
-	.setup		= serial8250_console_setup,
-	.flags		= CON_PRINTBUFFER,
-	.index		= -1,
-	.data		= &serial8250_reg,
-};
-
-static int __init serial8250_console_init(void)
-{
-	serial8250_isa_init_ports();
-	register_console(&serial8250_console);
-	return 0;
-}
-console_initcall(serial8250_console_init);
-
-#define SERIAL8250_CONSOLE	&serial8250_console
-#else
-#define SERIAL8250_CONSOLE	NULL
-#endif
-
-static struct uart_driver serial8250_reg = {
-	.owner			= THIS_MODULE,
-	.driver_name		= "serial",
-	.devfs_name		= "tts/",
-	.dev_name		= "ttyS",
-	.major			= TTY_MAJOR,
-	.minor			= 64,
-	.nr			= UART_NR,
-	.cons			= SERIAL8250_CONSOLE,
-};
-
-int __init early_serial_setup(struct uart_port *port)
-{
-	serial8250_isa_init_ports();
-	serial8250_ports[port->line].port	= *port;
-	serial8250_ports[port->line].port.ops	= &serial8250_pops;
-	return 0;
-}
-
-/**
- *	serial8250_suspend_port - suspend one serial port
- *	@line:  serial line number
- *      @level: the level of port suspension, as per uart_suspend_port
- *
- *	Suspend one serial port.
- */
-void serial8250_suspend_port(int line)
-{
-	uart_suspend_port(&serial8250_reg, &serial8250_ports[line].port);
-}
-
-/**
- *	serial8250_resume_port - resume one serial port
- *	@line:  serial line number
- *      @level: the level of port resumption, as per uart_resume_port
- *
- *	Resume one serial port.
- */
-void serial8250_resume_port(int line)
-{
-	uart_resume_port(&serial8250_reg, &serial8250_ports[line].port);
-}
-
-static int __init serial8250_init(void)
-{
-	int ret, i;
-
-	printk(KERN_INFO "Serial: Au1x00 driver\n");
-
-	for (i = 0; i < NR_IRQS; i++)
-		spin_lock_init(&irq_lists[i].lock);
-
-	ret = uart_register_driver(&serial8250_reg);
-	if (ret >= 0)
-		serial8250_register_ports(&serial8250_reg);
-
-	return ret;
-}
-
-static void __exit serial8250_exit(void)
-{
-	int i;
-
-	for (i = 0; i < UART_NR; i++)
-		uart_remove_one_port(&serial8250_reg, &serial8250_ports[i].port);
-
-	uart_unregister_driver(&serial8250_reg);
-}
-
-module_init(serial8250_init);
-module_exit(serial8250_exit);
-
-EXPORT_SYMBOL(serial8250_suspend_port);
-EXPORT_SYMBOL(serial8250_resume_port);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Au1x00 serial driver\n");
diff --git a/include/asm-mips/serial.h b/include/asm-mips/serial.h
index e796d75f027..7b236641220 100644
--- a/include/asm-mips/serial.h
+++ b/include/asm-mips/serial.h
@@ -103,88 +103,6 @@
 #define IVR_SERIAL_PORT_DEFNS
 #endif
 
-#ifdef CONFIG_SERIAL_AU1X00
-#include <asm/mach-au1x00/au1000.h>
-#ifdef CONFIG_SOC_AU1000
-#define AU1000_SERIAL_PORT_DEFNS                       \
-    { .baud_base = 0, .port = UART0_ADDR,              \
-      .iomem_base = (unsigned char *)UART0_ADDR,       \
-      .irq = AU1000_UART0_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART1_ADDR,              \
-      .iomem_base = (unsigned char *)UART1_ADDR,       \
-      .irq = AU1000_UART1_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART2_ADDR,              \
-      .iomem_base = (unsigned char *)UART2_ADDR,       \
-      .irq = AU1000_UART2_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART3_ADDR,              \
-      .iomem_base = (unsigned char *)UART3_ADDR,       \
-      .irq = AU1000_UART3_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },
-#endif
-
-#ifdef CONFIG_SOC_AU1500
-#define AU1000_SERIAL_PORT_DEFNS                       \
-    { .baud_base = 0, .port = UART0_ADDR,              \
-      .iomem_base = (unsigned char *)UART0_ADDR,       \
-      .irq = AU1500_UART0_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART3_ADDR,              \
-      .iomem_base = (unsigned char *)UART3_ADDR,       \
-      .irq = AU1500_UART3_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },
-#endif
-
-#ifdef CONFIG_SOC_AU1100
-#define AU1000_SERIAL_PORT_DEFNS                       \
-    { .baud_base = 0, .port = UART0_ADDR,              \
-      .iomem_base = (unsigned char *)UART0_ADDR,       \
-      .irq = AU1100_UART0_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART1_ADDR,              \
-      .iomem_base = (unsigned char *)UART1_ADDR,       \
-      .irq = AU1100_UART1_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART3_ADDR,              \
-      .iomem_base = (unsigned char *)UART3_ADDR,       \
-      .irq = AU1100_UART3_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },
-#endif
-
-#ifdef CONFIG_SOC_AU1550
-#define AU1000_SERIAL_PORT_DEFNS                       \
-    { .baud_base = 0, .port = UART0_ADDR,              \
-      .iomem_base = (unsigned char *)UART0_ADDR,       \
-      .irq = AU1550_UART0_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART1_ADDR,              \
-      .iomem_base = (unsigned char *)UART1_ADDR,       \
-      .irq = AU1550_UART1_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART3_ADDR,              \
-      .iomem_base = (unsigned char *)UART3_ADDR,       \
-      .irq = AU1550_UART3_INT,  .flags = STD_COM_FLAGS,\
-      .iomem_reg_shift = 2 },
-#endif
-
-#ifdef CONFIG_SOC_AU1200
-#define AU1000_SERIAL_PORT_DEFNS                       \
-    { .baud_base = 0, .port = UART0_ADDR,              \
-      .iomem_base = (unsigned char *)UART0_ADDR,       \
-      .irq = AU1200_UART0_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },                          \
-    { .baud_base = 0, .port = UART1_ADDR,              \
-      .iomem_base = (unsigned char *)UART1_ADDR,       \
-      .irq = AU1200_UART1_INT, .flags = STD_COM_FLAGS, \
-      .iomem_reg_shift = 2 },
-#endif
-
-#else
-#define AU1000_SERIAL_PORT_DEFNS
-#endif
-
 #ifdef CONFIG_HAVE_STD_PC_SERIAL_PORT
 #define STD_SERIAL_PORT_DEFNS			\
 	/* UART CLK   PORT IRQ     FLAGS        */			\
@@ -331,7 +249,6 @@
 	MOMENCO_OCELOT_G_SERIAL_PORT_DEFNS		\
 	MOMENCO_OCELOT_C_SERIAL_PORT_DEFNS		\
 	MOMENCO_OCELOT_SERIAL_PORT_DEFNS		\
-	MOMENCO_OCELOT_3_SERIAL_PORT_DEFNS		\
-	AU1000_SERIAL_PORT_DEFNS
+	MOMENCO_OCELOT_3_SERIAL_PORT_DEFNS
 
 #endif /* _ASM_SERIAL_H */