[ARM] 5056/1: [AT91] Cleanup YL9200 board file

Cleanup the YL9200 board-support file.

Other things fixed are:
 - Use new-style UART initialization
 - Register all LEDs as gpio_leds.
 - NOR Flash error noted in comments fixed by increasing YL9200_FLASH_SIZE
 - The only I2C device is the AT24C eeprom.
 - Setup of NWAIT pin and programming of SMC controller for the LCD/VGA.
 - Configure touchscreen interrupt pin.

Also adding the board to the KConfig and Makefile.

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

3 files changed, 394 insertions, 466 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 0fc07b6db74..3d549a9afe1 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -126,6 +126,12 @@ config MACH_ECBAT91
 	  Select this if you are using emQbit's ECB_AT91 board.
 	  <http://wiki.emqbit.com/free-ecb-at91>
 
+config MACH_YL9200
+	bool "ucDragon YL-9200"
+	depends on ARCH_AT91RM9200
+	help
+	  Select this if you are using the ucDragon YL-9200 board.
+
 endif
 
 # ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 8d9bc0153b1..995be14b2c4 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_MACH_ATEB9200)	+= board-eb9200.o
 obj-$(CONFIG_MACH_KAFA)		+= board-kafa.o
 obj-$(CONFIG_MACH_PICOTUX2XX)	+= board-picotux200.o
 obj-$(CONFIG_MACH_ECBAT91)	+= board-ecbat91.o
+obj-$(CONFIG_MACH_YL9200)	+= board-yl-9200.o
 
 # AT91SAM9260 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c
index b5717108991..7079050ab88 100755
--- a/arch/arm/mach-at91/board-yl-9200.c
+++ b/arch/arm/mach-at91/board-yl-9200.c
@@ -1,11 +1,10 @@
 /*
  * linux/arch/arm/mach-at91/board-yl-9200.c
  *
- * Adapted from:
- *various board files in
- * /arch/arm/mach-at91
- * modifications  to convert to  YL-9200 platform
- *  Copyright (C) 2007 S.Birtles
+ * Adapted from various board files in arch/arm/mach-at91
+ *
+ * Modifications for YL-9200 platform:
+ *  Copyright (C) 2007 S. Birtles
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -26,13 +25,14 @@
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
+#include <linux/dma-mapping.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
-/*#include <linux/can_bus/candata.h>*/
 #include <linux/spi/ads7846.h>
 #include <linux/mtd/physmap.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
 
-/*#include <sound/gpio_sounder.h>*/
 #include <asm/hardware.h>
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -45,179 +45,108 @@
 #include <asm/arch/board.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/at91rm9200_mc.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
 
 #include "generic.h"
-#include <asm/arch/at91_pio.h>
 
-#define YL_9200_FLASH_BASE	AT91_CHIPSELECT_0
-#define YL_9200_FLASH_SIZE	0x800000
 
-/*
- * Serial port configuration.
- *    0 .. 3 = USART0 .. USART3
- *    4      = DBGU
- *atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
- *atmel_usart.1: ttyS1 at MMIO 0xfffc0000 (irq = 6) is a ATMEL_SERIAL
- *atmel_usart.2: ttyS2 at MMIO 0xfffc4000 (irq = 7) is a ATMEL_SERIAL
- *atmel_usart.3: ttyS3 at MMIO 0xfffc8000 (irq = 8) is a ATMEL_SERIAL
- *atmel_usart.4: ttyS4 at MMIO 0xfffcc000 (irq = 9) is a ATMEL_SERIAL
- * on the YL-9200 we are sitting at the following
- *ttyS0 at MMIO 0xfefff200 (irq = 1) is a AT91_SERIAL
- *ttyS1 at MMIO 0xfefc4000 (irq = 7) is a AT91_SERIAL
- */
+static void __init yl9200_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_PQFP);
 
-/* extern void __init yl_9200_add_device_sounder(struct gpio_sounder *sounders, int nr);*/
+	/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
+	at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
 
-static struct at91_uart_config __initdata yl_9200_uart_config = {
-	.console_tty	= 0,				/* ttyS0 */
-	.nr_tty		= 3,
-	.tty_map	= { 4, 1, 0, -1, -1 }		/* ttyS0, ..., ttyS4 */
-};
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 
-static void __init yl_9200_map_io(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	/*Also initialises register clocks & gpio*/
-	at91rm9200_initialize(18432000, AT91RM9200_PQFP); /*we have a 3 bank system*/
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			| ATMEL_UART_RI);
 
-	/* Setup the serial ports and console */
-	at91_init_serial(&yl_9200_uart_config);
+	/* USART0 on ttyS2. (Rx & Tx only to JP3) */
+	at91_register_uart(AT91RM9200_ID_US0, 2, 0);
 
-	/* Setup the LEDs D2=PB17,D3=PB16 */
-	at91_init_leds(AT91_PIN_PB16,AT91_PIN_PB17); /*cpu-led,timer-led*/
+	/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
+	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
 }
 
-static void __init yl_9200_init_irq(void)
+static void __init yl9200_init_irq(void)
 {
 	at91rm9200_init_interrupts(NULL);
 }
 
-static struct at91_eth_data __initdata yl_9200_eth_data = {
-	.phy_irq_pin	= AT91_PIN_PB28,
-	.is_rmii	= 1,
-};
 
-static struct at91_usbh_data __initdata yl_9200_usbh_data = {
-	.ports		= 1,  /* this should be 1 not 2 for the Yl9200*/
+/*
+ * LEDs
+ */
+static struct gpio_led yl9200_leds[] = {
+	{	/* D2 */
+		.name			= "led2",
+		.gpio			= AT91_PIN_PB17,
+		.active_low		= 1,
+		.default_trigger	= "timer",
+	},
+	{	/* D3 */
+		.name			= "led3",
+		.gpio			= AT91_PIN_PB16,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	},
+	{	/* D4 */
+		.name			= "led4",
+		.gpio			= AT91_PIN_PB15,
+		.active_low		= 1,
+	},
+	{	/* D5 */
+		.name			= "led5",
+		.gpio			= AT91_PIN_PB8,
+		.active_low		= 1,
+	}
 };
 
-static struct at91_udc_data __initdata yl_9200_udc_data = {
-/*on sheet 7 Schemitic rev 1.0*/
-	.pullup_pin	= AT91_PIN_PC4,
-	.vbus_pin=  AT91_PIN_PC5,
-	.pullup_active_low = 1, /*ACTIVE LOW!! due to PNP transistor on page 7*/
-
-};
 /*
-static struct at91_cf_data __initdata yl_9200_cf_data = {
-TODO S.BIRTLES
-	.det_pin	= AT91_PIN_xxx,
-	.rst_pin	= AT91_PIN_xxx,
-	.irq_pin	= ... not connected
-	.vcc_pin	= ... always powered
-
+ * Ethernet
+ */
+static struct at91_eth_data __initdata yl9200_eth_data = {
+	.phy_irq_pin		= AT91_PIN_PB28,
+	.is_rmii		= 1,
 };
-*/
-static struct at91_mmc_data __initdata yl_9200_mmc_data = {
-	.det_pin	= AT91_PIN_PB9, /*THIS LOOKS CORRECT SHEET7*/
-/*	.wp_pin		= ... not connected  SHEET7*/
-	.slot_b		= 0,
-	.wire4		= 1,
 
+/*
+ * USB Host
+ */
+static struct at91_usbh_data __initdata yl9200_usbh_data = {
+	.ports			= 1,	/* PQFP version of AT91RM9200 */
 };
 
-/* --------------------------------------------------------------------
- *  Touch screen
- * -------------------------------------------------------------------- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
-	return !at91_get_gpio_value(AT91_PIN_PB11);	/* Touchscreen PENIRQ */
-}
-
-static void __init at91_init_device_ts(void)
-{
-/*IMPORTANT NOTE THE SPI INTERFACE IS ALREADY CONFIGURED BY XXX_DEVICES.C
-THAT IS TO SAY THAT  MISO,MOSI,SPCK AND CS  are already configured
-we only need to enable the other datapins which are:
-PB10/RK1 BUSY
-*/
-/* Touchscreen BUSY signal ,  pin,use pullup ( TODO not currently used in the ADS7843/6.c driver)*/
-at91_set_gpio_input(AT91_PIN_PB10, 1);
-}
-
-#else
-static void __init at91_init_device_ts(void) {}
-#endif
-
-static struct ads7846_platform_data ads_info = {
-	.model			= 7843,
-	.x_min			= 150,
-	.x_max			= 3830,
-	.y_min			= 190,
-	.y_max			= 3830,
-	.vref_delay_usecs	= 100,
-/* for a 8" touch screen*/
-	//.x_plate_ohms		= 603, //= 450, S.Birtles TODO
-	//.y_plate_ohms		= 332, //= 250, S.Birtles TODO
-/*for a 10.4" touch screen*/
-	//.x_plate_ohms		=611,
-	//.y_plate_ohms		=325,
-
-	.x_plate_ohms	= 576,
-	.y_plate_ohms	= 366,
-		//
-	.pressure_max		= 15000, /*generally nonsense on the 7843*/
-	 /*number of times to send query to chip in a given run 0 equals one time (do not set to 0!! ,there is a bug in ADS 7846 code)*/
-	.debounce_max		= 1,
-	.debounce_rep		= 0,
-	.debounce_tol		= (~0),
-	.get_pendown_state	= ads7843_pendown_state,
-};
+/*
+ * USB Device
+ */
+static struct at91_udc_data __initdata yl9200_udc_data = {
+	.pullup_pin		= AT91_PIN_PC4,
+	.vbus_pin		= AT91_PIN_PC5,
+	.pullup_active_low	= 1,	/* Active Low due to PNP transistor (pg 7) */
 
-/*static struct canbus_platform_data can_info = {
-	.model			= 2510,
 };
-*/
-
-static struct spi_board_info yl_9200_spi_devices[] = {
-/*this sticks it at:
- /sys/devices/platform/atmel_spi.0/spi0.0
- /sys/bus/platform/devices/
-Documentation/spi IIRC*/
 
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
- /*(this IS correct 04-NOV-2007)*/
-	{
-		.modalias		= "ads7846", /* because the driver is called ads7846*/
-		.chip_select	= 0, /*THIS MUST BE AN INDEX INTO AN ARRAY OF  pins */
-/*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select*/
-		/*.controller_data =AT91_PIN_PA3 ,*/
-		.max_speed_hz	= 5000*26, /*(4700 * 26)-125000 * 26, (max sample rate @ 3V) * (cmd + data + overhead) */
-		.bus_num		= 0,
-		.platform_data	= &ads_info,
-		.irq			= AT91_PIN_PB11,
-	},
-#endif
-/*we need to put our CAN driver data here!!*/
-/*THIS IS ALL DUMMY DATA*/
-/*	{
-		.modalias		= "mcp2510", //DUMMY for MCP2510 chip
-		.chip_select	= 1,*/ /*THIS MUST BE AN INDEX INTO AN ARRAY OF  pins */
-	/*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select */
-	/*  .controller_data =AT91_PIN_PA4 ,
-		.max_speed_hz	= 25000 * 26,
-		.bus_num		= 0,
-		.platform_data	= &can_info,
-		.irq			= AT91_PIN_PC0,
-	},
-	*/
-	//max SPI chip needs to go here
+/*
+ * MMC
+ */
+static struct at91_mmc_data __initdata yl9200_mmc_data = {
+	.det_pin	= AT91_PIN_PB9,
+	// .wp_pin	= ... not connected
+	.wire4		= 1,
 };
 
-static struct mtd_partition __initdata yl_9200_nand_partition[] = {
+/*
+ * NAND Flash
+ */
+static struct mtd_partition __initdata yl9200_nand_partition[] = {
 	{
 		.name	= "AT91 NAND partition 1, boot",
 		.offset	= 0,
@@ -242,442 +171,434 @@ static struct mtd_partition __initdata yl_9200_nand_partition[] = {
 		.name	= "AT91 NAND partition 5, ext-fs",
 		.offset	= 32 * SZ_1M,
 		.size	= 32 * SZ_1M
-	},
+	}
 };
 
 static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
 {
-	*num_partitions = ARRAY_SIZE(yl_9200_nand_partition);
-	return yl_9200_nand_partition;
+	*num_partitions = ARRAY_SIZE(yl9200_nand_partition);
+	return yl9200_nand_partition;
 }
 
-static struct at91_nand_data __initdata yl_9200_nand_data = {
-	.ale= 6,
-	.cle= 7,
-	/*.det_pin	= AT91_PIN_PCxx,*/   /*we don't have a det pin because NandFlash is fixed to board*/
-	.rdy_pin	= AT91_PIN_PC14,  /*R/!B Sheet10*/
-	.enable_pin	= AT91_PIN_PC15,  /*!CE  Sheet10 */
+static struct at91_nand_data __initdata yl9200_nand_data = {
+	.ale		= 6,
+	.cle		= 7,
+	// .det_pin	= ... not connected
+	.rdy_pin	= AT91_PIN_PC14,	/* R/!B (Sheet10) */
+	.enable_pin	= AT91_PIN_PC15,	/* !CE  (Sheet10) */
 	.partition_info	= nand_partitions,
 };
 
-
-
 /*
-TODO S.Birtles
-potentially a problem with the size above
-physmap platform flash device: 00800000 at 10000000
-physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
-NOR chip too large to fit in mapping. Attempting to cope...
- Intel/Sharp Extended Query Table at 0x0031
-Using buffer write method
-cfi_cmdset_0001: Erase suspend on write enabled
-Reducing visibility of 16384KiB chip to 8192KiB
-*/
+ * NOR Flash
+ */
+#define YL9200_FLASH_BASE	AT91_CHIPSELECT_0
+#define YL9200_FLASH_SIZE	0x1000000
 
-static struct mtd_partition yl_9200_flash_partitions[] = {
+static struct mtd_partition yl9200_flash_partitions[] = {
+	{
+		.name		= "Bootloader",
+		.size		= 0x00040000,
+		.offset		= 0,
+		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
+	},
 	{
-		.name =		"Bootloader",
-		.size =		0x00040000,
-		.offset =	0,
-		.mask_flags =	MTD_WRITEABLE  /* force read-only */
-	},{
-		.name =		"Kernel",
-		.size =		0x001C0000,
-		.offset =	0x00040000,
-	},{
-		.name =		"Filesystem",
-		.size =		MTDPART_SIZ_FULL,
-		.offset =	0x00200000
+		.name		= "Kernel",
+		.size		= 0x001C0000,
+		.offset		= 0x00040000,
+	},
+	{
+		.name		= "Filesystem",
+		.size		= MTDPART_SIZ_FULL,
+		.offset		= 0x00200000
 	}
-
 };
 
-static struct physmap_flash_data yl_9200_flash_data = {
-	.width	= 2,
-	.parts          = yl_9200_flash_partitions,
-	.nr_parts       = ARRAY_SIZE(yl_9200_flash_partitions),
+static struct physmap_flash_data yl9200_flash_data = {
+	.width		= 2,
+	.parts		= yl9200_flash_partitions,
+	.nr_parts	= ARRAY_SIZE(yl9200_flash_partitions),
 };
 
-static struct resource yl_9200_flash_resources[] = {
-{
-	.start		= YL_9200_FLASH_BASE,
-	.end		= YL_9200_FLASH_BASE + YL_9200_FLASH_SIZE - 1,
-	.flags		= IORESOURCE_MEM,
+static struct resource yl9200_flash_resources[] = {
+	{
+		.start	= YL9200_FLASH_BASE,
+		.end	= YL9200_FLASH_BASE + YL9200_FLASH_SIZE - 1,
+		.flags	= IORESOURCE_MEM,
 	}
 };
 
-static struct platform_device yl_9200_flash = {
+static struct platform_device yl9200_flash = {
 	.name		= "physmap-flash",
 	.id		= 0,
 	.dev		= {
-				.platform_data	= &yl_9200_flash_data,
+				.platform_data	= &yl9200_flash_data,
 			},
-	.resource	= yl_9200_flash_resources,
-	.num_resources  = ARRAY_SIZE(yl_9200_flash_resources),
+	.resource	= yl9200_flash_resources,
+	.num_resources	= ARRAY_SIZE(yl9200_flash_resources),
 };
 
-
-static struct gpio_led yl_9200_leds[] = {
-/*D2 &D3 are passed directly in via at91_init_leds*/
-	{
-		.name			= "led4",  /*D4*/
-		.gpio			= AT91_PIN_PB15,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-		/*.default_trigger	= "timer",*/
-	},
-	{
-		.name			= "led5",  /*D5*/
-		.gpio			= AT91_PIN_PB8,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-//static struct gpio_sounder yl_9200_sounder[] = {*/
-/*This is a simple speaker attached to a gpo line*/
-
-//	{
-//		.name			= "Speaker",  /*LS1*/
-//		.gpio			= AT91_PIN_PA22,
-//		.active_low		= 0,
-//		.default_trigger	= "heartbeat",
-		/*.default_trigger	= "timer",*/
-//	},
-//};
-
-
-
-static struct i2c_board_info __initdata yl_9200_i2c_devices[] = {
-	{
-	/*TODO*/
-		I2C_BOARD_INFO("CS4334", 0x00),
+/*
+ * I2C (TWI)
+ */
+static struct i2c_board_info __initdata yl9200_i2c_devices[] = {
+	{	/* EEPROM */
+		I2C_BOARD_INFO("24c128", 0x50),
 	}
 };
 
-
- /*
+/*
  * GPIO Buttons
- */
+*/
 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button yl_9200_buttons[] = {
+static struct gpio_keys_button yl9200_buttons[] = {
 	{
 		.gpio		= AT91_PIN_PA24,
-		.code	= BTN_2,
+		.code		= BTN_2,
 		.desc		= "SW2",
 		.active_low	= 1,
 		.wakeup		= 1,
 	},
 	{
 		.gpio		= AT91_PIN_PB1,
-		.code	= BTN_3,
+		.code		= BTN_3,
 		.desc		= "SW3",
 		.active_low	= 1,
 		.wakeup		= 1,
 	},
 	{
 		.gpio		= AT91_PIN_PB2,
-		.code	= BTN_4,
+		.code		= BTN_4,
 		.desc		= "SW4",
 		.active_low	= 1,
 		.wakeup		= 1,
 	},
 	{
 		.gpio		= AT91_PIN_PB6,
-		.code	= BTN_5,
+		.code		= BTN_5,
 		.desc		= "SW5",
 		.active_low	= 1,
 		.wakeup		= 1,
-	},
-
+	}
 };
 
-static struct gpio_keys_platform_data yl_9200_button_data = {
-	.buttons	= yl_9200_buttons,
-	.nbuttons	= ARRAY_SIZE(yl_9200_buttons),
+static struct gpio_keys_platform_data yl9200_button_data = {
+	.buttons	= yl9200_buttons,
+	.nbuttons	= ARRAY_SIZE(yl9200_buttons),
 };
 
-static struct platform_device yl_9200_button_device = {
+static struct platform_device yl9200_button_device = {
 	.name		= "gpio-keys",
 	.id		= -1,
 	.num_resources	= 0,
 	.dev		= {
-	.platform_data	= &yl_9200_button_data,
+		.platform_data	= &yl9200_button_data,
 	}
 };
 
-static void __init yl_9200_add_device_buttons(void)
+static void __init yl9200_add_device_buttons(void)
 {
-	//SW2
-	at91_set_gpio_input(AT91_PIN_PA24, 0);
+	at91_set_gpio_input(AT91_PIN_PA24, 1);	/* SW2 */
 	at91_set_deglitch(AT91_PIN_PA24, 1);
-
-	//SW3
-	at91_set_gpio_input(AT91_PIN_PB1, 0);
+	at91_set_gpio_input(AT91_PIN_PB1, 1);	/* SW3 */
 	at91_set_deglitch(AT91_PIN_PB1, 1);
-	//SW4
-	at91_set_gpio_input(AT91_PIN_PB2, 0);
+	at91_set_gpio_input(AT91_PIN_PB2, 1);	/* SW4 */
 	at91_set_deglitch(AT91_PIN_PB2, 1);
-
-	//SW5
-	at91_set_gpio_input(AT91_PIN_PB6, 0);
+	at91_set_gpio_input(AT91_PIN_PB6, 1);	/* SW5 */
 	at91_set_deglitch(AT91_PIN_PB6, 1);
 
+	/* Enable buttons (Sheet 5) */
+	at91_set_gpio_output(AT91_PIN_PB7, 1);
+
+	platform_device_register(&yl9200_button_device);
+}
+#else
+static void __init yl9200_add_device_buttons(void) {}
+#endif
+
+/*
+ * Touchscreen
+ */
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+static int ads7843_pendown_state(void)
+{
+	return !at91_get_gpio_value(AT91_PIN_PB11);	/* Touchscreen PENIRQ */
+}
+
+static struct ads7846_platform_data ads_info = {
+	.model			= 7843,
+	.x_min			= 150,
+	.x_max			= 3830,
+	.y_min			= 190,
+	.y_max			= 3830,
+	.vref_delay_usecs	= 100,
+
+	/* For a 8" touch-screen */
+	// .x_plate_ohms		= 603,
+	// .y_plate_ohms		= 332,
+
+	/* For a 10.4" touch-screen */
+	// .x_plate_ohms		= 611,
+	// .y_plate_ohms		= 325,
+
+	.x_plate_ohms		= 576,
+	.y_plate_ohms		= 366,
+
+	.pressure_max		= 15000, /* generally nonsense on the 7843 */
+	.debounce_max		= 1,
+	.debounce_rep		= 0,
+	.debounce_tol		= (~0),
+	.get_pendown_state	= ads7843_pendown_state,
+};
 
-	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* #TURN BUTTONS ON, SHEET 5  of schematics */
-	platform_device_register(&yl_9200_button_device);
+static void __init yl9200_add_device_ts(void)
+{
+	at91_set_gpio_input(AT91_PIN_PB11, 1);	/* Touchscreen interrupt pin */
+	at91_set_gpio_input(AT91_PIN_PB10, 1);	/* Touchscreen BUSY signal - not used! */
 }
 #else
-static void __init yl_9200_add_device_buttons(void) {}
+static void __init yl9200_add_device_ts(void) {}
+#endif
+
+/*
+ * SPI devices
+ */
+static struct spi_board_info yl9200_spi_devices[] = {
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+	{	/* Touchscreen */
+		.modalias	= "ads7846",
+		.chip_select	= 0,
+		.max_speed_hz	= 5000 * 26,
+		.platform_data	= &ads_info,
+		.irq		= AT91_PIN_PB11,
+	},
 #endif
+	{	/* CAN */
+		.modalias	= "mcp2510",
+		.chip_select	= 1,
+		.max_speed_hz	= 25000 * 26,
+		.irq		= AT91_PIN_PC0,
+	}
+};
 
+/*
+ * LCD / VGA
+ *
+ * EPSON S1D13806 FB (discontinued chip)
+ * EPSON S1D13506 FB
+ */
 #if defined(CONFIG_FB_S1D135XX) || defined(CONFIG_FB_S1D13XXX_MODULE)
 #include <video/s1d13xxxfb.h>
 
-/* EPSON S1D13806 FB (discontinued chip)*/
-/* EPSON S1D13506 FB */
-
 #define AT91_FB_REG_BASE	0x80000000L
 #define AT91_FB_REG_SIZE	0x200
 #define AT91_FB_VMEM_BASE	0x80200000L
 #define AT91_FB_VMEM_SIZE	0x200000L
 
-/*#define S1D_DISPLAY_WIDTH           640*/
-/*#define S1D_DISPLAY_HEIGHT          480*/
-
-
-static void __init yl_9200_init_video(void)
+static void __init yl9200_init_video(void)
 {
-	at91_sys_write(AT91_PIOC + PIO_ASR,AT91_PIN_PC6);
-	at91_sys_write(AT91_PIOC + PIO_BSR,0);
-	at91_sys_write(AT91_PIOC + PIO_ASR,AT91_PIN_PC6);
-
-	at91_sys_write( AT91_SMC_CSR(2),
-	AT91_SMC_NWS_(0x4) |
-	AT91_SMC_WSEN |
-	AT91_SMC_TDF_(0x100) |
-	AT91_SMC_DBW
-	);
-
-
+	/* NWAIT Signal */
+	at91_set_A_periph(AT91_PIN_PC6, 0);
 
+	/* Initialization of the Static Memory Controller for Chip Select 2 */
+	at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16		/* 16 bit */
+			| AT91_SMC_WSEN | AT91_SMC_NWS_(0x4)	/* wait states */
+			| AT91_SMC_TDF_(0x100)			/* float time */
+	);
 }
 
-
-static struct s1d13xxxfb_regval yl_9200_s1dfb_initregs[] =
+static struct s1d13xxxfb_regval yl9200_s1dfb_initregs[] =
 {
-	{S1DREG_MISC,				0x00},   /* Miscellaneous Register*/
-	{S1DREG_COM_DISP_MODE,		0x01},   /* Display Mode Register, LCD only*/
-	{S1DREG_GPIO_CNF0,			0x00},   /* General IO Pins Configuration Register*/
-	{S1DREG_GPIO_CTL0,			0x00},   /* General IO Pins Control Register*/
-	{S1DREG_CLK_CNF,			0x11},   /* Memory Clock Configuration Register*/
-	{S1DREG_LCD_CLK_CNF,		0x10},   /* LCD Pixel Clock Configuration Register*/
-	{S1DREG_CRT_CLK_CNF,		0x12},   /* CRT/TV Pixel Clock Configuration Register*/
-	{S1DREG_MPLUG_CLK_CNF,		0x01},   /* MediaPlug Clock Configuration Register*/
-	{S1DREG_CPU2MEM_WST_SEL,	0x02},   /* CPU To Memory Wait State Select Register*/
-	{S1DREG_MEM_CNF,			0x00},   /* Memory Configuration Register*/
-	{S1DREG_SDRAM_REF_RATE,		0x04},   /* DRAM Refresh Rate Register, MCLK source*/
-	{S1DREG_SDRAM_TC0,			0x12},   /* DRAM Timings Control Register 0*/
-	{S1DREG_SDRAM_TC1,			0x02},   /* DRAM Timings Control Register 1*/
-	{S1DREG_PANEL_TYPE,			0x25},   /* Panel Type Register*/
-	{S1DREG_MOD_RATE,			0x00},   /* MOD Rate Register*/
-	{S1DREG_LCD_DISP_HWIDTH,	0x4F},   /* LCD Horizontal Display Width Register*/
-	{S1DREG_LCD_NDISP_HPER,		0x13},   /* LCD Horizontal Non-Display Period Register*/
-	{S1DREG_TFT_FPLINE_START,	0x01},   /* TFT FPLINE Start Position Register*/
-	{S1DREG_TFT_FPLINE_PWIDTH,	0x0c},   /* TFT FPLINE Pulse Width Register*/
-	{S1DREG_LCD_DISP_VHEIGHT0,	0xDF},   /* LCD Vertical Display Height Register 0*/
-	{S1DREG_LCD_DISP_VHEIGHT1,	0x01},   /* LCD Vertical Display Height Register 1*/
-	{S1DREG_LCD_NDISP_VPER,		0x2c},   /* LCD Vertical Non-Display Period Register*/
-	{S1DREG_TFT_FPFRAME_START,	0x0a},   /* TFT FPFRAME Start Position Register*/
-	{S1DREG_TFT_FPFRAME_PWIDTH,	0x02},   /* TFT FPFRAME Pulse Width Register*/
-	{S1DREG_LCD_DISP_MODE,		0x05},   /* LCD Display Mode Register*/
-	{S1DREG_LCD_MISC,			0x01},   /* LCD Miscellaneous Register*/
-	{S1DREG_LCD_DISP_START0,	0x00},   /* LCD Display Start Address Register 0*/
-	{S1DREG_LCD_DISP_START1,	0x00},   /* LCD Display Start Address Register 1*/
-	{S1DREG_LCD_DISP_START2,	0x00},   /* LCD Display Start Address Register 2*/
-	{S1DREG_LCD_MEM_OFF0,		0x80},   /* LCD Memory Address Offset Register 0*/
-	{S1DREG_LCD_MEM_OFF1,		0x02},   /* LCD Memory Address Offset Register 1*/
-	{S1DREG_LCD_PIX_PAN,		0x03},   /* LCD Pixel Panning Register*/
-	{S1DREG_LCD_DISP_FIFO_HTC,	0x00},   /* LCD Display FIFO High Threshold Control Register*/
-	{S1DREG_LCD_DISP_FIFO_LTC,	0x00},   /* LCD Display FIFO Low Threshold Control Register*/
-	{S1DREG_CRT_DISP_HWIDTH,	0x4F},   /* CRT/TV Horizontal Display Width Register*/
-	{S1DREG_CRT_NDISP_HPER,		0x13},   /* CRT/TV Horizontal Non-Display Period Register*/
-	{S1DREG_CRT_HRTC_START,		0x01},   /* CRT/TV HRTC Start Position Register*/
-	{S1DREG_CRT_HRTC_PWIDTH,	0x0B},   /* CRT/TV HRTC Pulse Width Register*/
-	{S1DREG_CRT_DISP_VHEIGHT0,	0xDF},   /* CRT/TV Vertical Display Height Register 0*/
-	{S1DREG_CRT_DISP_VHEIGHT1,	0x01},   /* CRT/TV Vertical Display Height Register 1*/
-	{S1DREG_CRT_NDISP_VPER,		0x2B},   /* CRT/TV Vertical Non-Display Period Register*/
-	{S1DREG_CRT_VRTC_START,		0x09},   /* CRT/TV VRTC Start Position Register*/
-	{S1DREG_CRT_VRTC_PWIDTH,	0x01},   /* CRT/TV VRTC Pulse Width Register*/
-	{S1DREG_TV_OUT_CTL,			0x18},   /* TV Output Control Register */
-	{S1DREG_CRT_DISP_MODE,		0x05},   /* CRT/TV Display Mode Register, 16BPP*/
-	{S1DREG_CRT_DISP_START0,	0x00},   /* CRT/TV Display Start Address Register 0*/
-	{S1DREG_CRT_DISP_START1,	0x00},   /* CRT/TV Display Start Address Register 1*/
-	{S1DREG_CRT_DISP_START2,	0x00},   /* CRT/TV Display Start Address Register 2*/
-	{S1DREG_CRT_MEM_OFF0,		0x80},   /* CRT/TV Memory Address Offset Register 0*/
-	{S1DREG_CRT_MEM_OFF1,		0x02},   /* CRT/TV Memory Address Offset Register 1*/
-	{S1DREG_CRT_PIX_PAN,		0x00},   /* CRT/TV Pixel Panning Register*/
-	{S1DREG_CRT_DISP_FIFO_HTC,	0x00},   /* CRT/TV Display FIFO High Threshold Control Register*/
-	{S1DREG_CRT_DISP_FIFO_LTC,	0x00},   /* CRT/TV Display FIFO Low Threshold Control Register*/
-	{S1DREG_LCD_CUR_CTL,		0x00},   /* LCD Ink/Cursor Control Register*/
-	{S1DREG_LCD_CUR_START,		0x01},   /* LCD Ink/Cursor Start Address Register*/
-	{S1DREG_LCD_CUR_XPOS0,		0x00},   /* LCD Cursor X Position Register 0*/
-	{S1DREG_LCD_CUR_XPOS1,		0x00},   /* LCD Cursor X Position Register 1*/
-	{S1DREG_LCD_CUR_YPOS0,		0x00},   /* LCD Cursor Y Position Register 0*/
-	{S1DREG_LCD_CUR_YPOS1,		0x00},   /* LCD Cursor Y Position Register 1*/
-	{S1DREG_LCD_CUR_BCTL0,		0x00},   /* LCD Ink/Cursor Blue Color 0 Register*/
-	{S1DREG_LCD_CUR_GCTL0,		0x00},   /* LCD Ink/Cursor Green Color 0 Register*/
-	{S1DREG_LCD_CUR_RCTL0,		0x00},   /* LCD Ink/Cursor Red Color 0 Register*/
-	{S1DREG_LCD_CUR_BCTL1,		0x1F},   /* LCD Ink/Cursor Blue Color 1 Register*/
-	{S1DREG_LCD_CUR_GCTL1,		0x3F},   /* LCD Ink/Cursor Green Color 1 Register*/
-	{S1DREG_LCD_CUR_RCTL1,		0x1F},   /* LCD Ink/Cursor Red Color 1 Register*/
-	{S1DREG_LCD_CUR_FIFO_HTC,	0x00},   /* LCD Ink/Cursor FIFO Threshold Register*/
-	{S1DREG_CRT_CUR_CTL,		0x00},   /* CRT/TV Ink/Cursor Control Register*/
-	{S1DREG_CRT_CUR_START,		0x01},   /* CRT/TV Ink/Cursor Start Address Register*/
-	{S1DREG_CRT_CUR_XPOS0,		0x00},   /* CRT/TV Cursor X Position Register 0*/
-	{S1DREG_CRT_CUR_XPOS1,		0x00},   /* CRT/TV Cursor X Position Register 1*/
-	{S1DREG_CRT_CUR_YPOS0,		0x00},   /* CRT/TV Cursor Y Position Register 0*/
-	{S1DREG_CRT_CUR_YPOS1,		0x00},   /* CRT/TV Cursor Y Position Register 1*/
-	{S1DREG_CRT_CUR_BCTL0,		0x00},   /* CRT/TV Ink/Cursor Blue Color 0 Register*/
-	{S1DREG_CRT_CUR_GCTL0,		0x00},   /* CRT/TV Ink/Cursor Green Color 0 Register*/
-	{S1DREG_CRT_CUR_RCTL0,		0x00},   /* CRT/TV Ink/Cursor Red Color 0 Register*/
-	{S1DREG_CRT_CUR_BCTL1,		0x1F},   /* CRT/TV Ink/Cursor Blue Color 1 Register*/
-	{S1DREG_CRT_CUR_GCTL1,		0x3F},   /* CRT/TV Ink/Cursor Green Color 1 Register*/
-	{S1DREG_CRT_CUR_RCTL1,		0x1F},   /* CRT/TV Ink/Cursor Red Color 1 Register*/
-	{S1DREG_CRT_CUR_FIFO_HTC,	0x00},   /* CRT/TV Ink/Cursor FIFO Threshold Register*/
-	{S1DREG_BBLT_CTL0,			0x00},   /* BitBlt Control Register 0*/
-	{S1DREG_BBLT_CTL1,			0x01},   /* BitBlt Control Register 1*/
-	{S1DREG_BBLT_CC_EXP,		0x00},   /* BitBlt ROP Code/Color Expansion Register*/
-	{S1DREG_BBLT_OP,			0x00},   /* BitBlt Operation Register*/
-	{S1DREG_BBLT_SRC_START0,	0x00},   /* BitBlt Source Start Address Register 0*/
-	{S1DREG_BBLT_SRC_START1,	0x00},   /* BitBlt Source Start Address Register 1*/
-	{S1DREG_BBLT_SRC_START2,	0x00},   /* BitBlt Source Start Address Register 2*/
-	{S1DREG_BBLT_DST_START0,	0x00},   /* BitBlt Destination Start Address Register 0*/
-	{S1DREG_BBLT_DST_START1,	0x00},   /* BitBlt Destination Start Address Register 1*/
-	{S1DREG_BBLT_DST_START2,	0x00},   /* BitBlt Destination Start Address Register 2*/
-	{S1DREG_BBLT_MEM_OFF0,		0x00},   /* BitBlt Memory Address Offset Register 0*/
-	{S1DREG_BBLT_MEM_OFF1,		0x00},   /* BitBlt Memory Address Offset Register 1*/
-	{S1DREG_BBLT_WIDTH0,		0x00},   /* BitBlt Width Register 0*/
-	{S1DREG_BBLT_WIDTH1,		0x00},   /* BitBlt Width Register 1*/
-	{S1DREG_BBLT_HEIGHT0,		0x00},   /* BitBlt Height Register 0*/
-	{S1DREG_BBLT_HEIGHT1,		0x00},   /* BitBlt Height Register 1*/
-	{S1DREG_BBLT_BGC0,			0x00},   /* BitBlt Background Color Register 0*/
-	{S1DREG_BBLT_BGC1,			0x00},   /* BitBlt Background Color Register 1*/
-	{S1DREG_BBLT_FGC0,			0x00},   /* BitBlt Foreground Color Register 0*/
-	{S1DREG_BBLT_FGC1,			0x00},   /* BitBlt Foreground Color Register 1*/
-	{S1DREG_LKUP_MODE,			0x00},   /* Look-Up Table Mode Register*/
-	{S1DREG_LKUP_ADDR,			0x00},   /* Look-Up Table Address Register*/
-	{S1DREG_PS_CNF,				0x00},   /* Power Save Configuration Register*/
-	{S1DREG_PS_STATUS,			0x00},   /* Power Save Status Register*/
-	{S1DREG_CPU2MEM_WDOGT,		0x00},   /* CPU-to-Memory Access Watchdog Timer Register*/
-	{S1DREG_COM_DISP_MODE,		0x01},   /* Display Mode Register, LCD only*/
+	{S1DREG_MISC,			0x00},	/* Miscellaneous Register*/
+	{S1DREG_COM_DISP_MODE,		0x01},	/* Display Mode Register, LCD only*/
+	{S1DREG_GPIO_CNF0,		0x00},	/* General IO Pins Configuration Register*/
+	{S1DREG_GPIO_CTL0,		0x00},	/* General IO Pins Control Register*/
+	{S1DREG_CLK_CNF,		0x11},	/* Memory Clock Configuration Register*/
+	{S1DREG_LCD_CLK_CNF,		0x10},	/* LCD Pixel Clock Configuration Register*/
+	{S1DREG_CRT_CLK_CNF,		0x12},	/* CRT/TV Pixel Clock Configuration Register*/
+	{S1DREG_MPLUG_CLK_CNF,		0x01},	/* MediaPlug Clock Configuration Register*/
+	{S1DREG_CPU2MEM_WST_SEL,	0x02},	/* CPU To Memory Wait State Select Register*/
+	{S1DREG_MEM_CNF,		0x00},	/* Memory Configuration Register*/
+	{S1DREG_SDRAM_REF_RATE,		0x04},	/* DRAM Refresh Rate Register, MCLK source*/
+	{S1DREG_SDRAM_TC0,		0x12},	/* DRAM Timings Control Register 0*/
+	{S1DREG_SDRAM_TC1,		0x02},	/* DRAM Timings Control Register 1*/
+	{S1DREG_PANEL_TYPE,		0x25},	/* Panel Type Register*/
+	{S1DREG_MOD_RATE,		0x00},	/* MOD Rate Register*/
+	{S1DREG_LCD_DISP_HWIDTH,	0x4F},	/* LCD Horizontal Display Width Register*/
+	{S1DREG_LCD_NDISP_HPER,		0x13},	/* LCD Horizontal Non-Display Period Register*/
+	{S1DREG_TFT_FPLINE_START,	0x01},	/* TFT FPLINE Start Position Register*/
+	{S1DREG_TFT_FPLINE_PWIDTH,	0x0c},	/* TFT FPLINE Pulse Width Register*/
+	{S1DREG_LCD_DISP_VHEIGHT0,	0xDF},	/* LCD Vertical Display Height Register 0*/
+	{S1DREG_LCD_DISP_VHEIGHT1,	0x01},	/* LCD Vertical Display Height Register 1*/
+	{S1DREG_LCD_NDISP_VPER,		0x2c},	/* LCD Vertical Non-Display Period Register*/
+	{S1DREG_TFT_FPFRAME_START,	0x0a},	/* TFT FPFRAME Start Position Register*/
+	{S1DREG_TFT_FPFRAME_PWIDTH,	0x02},	/* TFT FPFRAME Pulse Width Register*/
+	{S1DREG_LCD_DISP_MODE,		0x05},	/* LCD Display Mode Register*/
+	{S1DREG_LCD_MISC,		0x01},	/* LCD Miscellaneous Register*/
+	{S1DREG_LCD_DISP_START0,	0x00},	/* LCD Display Start Address Register 0*/
+	{S1DREG_LCD_DISP_START1,	0x00},	/* LCD Display Start Address Register 1*/
+	{S1DREG_LCD_DISP_START2,	0x00},	/* LCD Display Start Address Register 2*/
+	{S1DREG_LCD_MEM_OFF0,		0x80},	/* LCD Memory Address Offset Register 0*/
+	{S1DREG_LCD_MEM_OFF1,		0x02},	/* LCD Memory Address Offset Register 1*/
+	{S1DREG_LCD_PIX_PAN,		0x03},	/* LCD Pixel Panning Register*/
+	{S1DREG_LCD_DISP_FIFO_HTC,	0x00},	/* LCD Display FIFO High Threshold Control Register*/
+	{S1DREG_LCD_DISP_FIFO_LTC,	0x00},	/* LCD Display FIFO Low Threshold Control Register*/
+	{S1DREG_CRT_DISP_HWIDTH,	0x4F},	/* CRT/TV Horizontal Display Width Register*/
+	{S1DREG_CRT_NDISP_HPER,		0x13},	/* CRT/TV Horizontal Non-Display Period Register*/
+	{S1DREG_CRT_HRTC_START,		0x01},	/* CRT/TV HRTC Start Position Register*/
+	{S1DREG_CRT_HRTC_PWIDTH,	0x0B},	/* CRT/TV HRTC Pulse Width Register*/
+	{S1DREG_CRT_DISP_VHEIGHT0,	0xDF},	/* CRT/TV Vertical Display Height Register 0*/
+	{S1DREG_CRT_DISP_VHEIGHT1,	0x01},	/* CRT/TV Vertical Display Height Register 1*/
+	{S1DREG_CRT_NDISP_VPER,		0x2B},	/* CRT/TV Vertical Non-Display Period Register*/
+	{S1DREG_CRT_VRTC_START,		0x09},	/* CRT/TV VRTC Start Position Register*/
+	{S1DREG_CRT_VRTC_PWIDTH,	0x01},	/* CRT/TV VRTC Pulse Width Register*/
+	{S1DREG_TV_OUT_CTL,		0x18},	/* TV Output Control Register */
+	{S1DREG_CRT_DISP_MODE,		0x05},	/* CRT/TV Display Mode Register, 16BPP*/
+	{S1DREG_CRT_DISP_START0,	0x00},	/* CRT/TV Display Start Address Register 0*/
+	{S1DREG_CRT_DISP_START1,	0x00},	/* CRT/TV Display Start Address Register 1*/
+	{S1DREG_CRT_DISP_START2,	0x00},	/* CRT/TV Display Start Address Register 2*/
+	{S1DREG_CRT_MEM_OFF0,		0x80},	/* CRT/TV Memory Address Offset Register 0*/
+	{S1DREG_CRT_MEM_OFF1,		0x02},	/* CRT/TV Memory Address Offset Register 1*/
+	{S1DREG_CRT_PIX_PAN,		0x00},	/* CRT/TV Pixel Panning Register*/
+	{S1DREG_CRT_DISP_FIFO_HTC,	0x00},	/* CRT/TV Display FIFO High Threshold Control Register*/
+	{S1DREG_CRT_DISP_FIFO_LTC,	0x00},	/* CRT/TV Display FIFO Low Threshold Control Register*/
+	{S1DREG_LCD_CUR_CTL,		0x00},	/* LCD Ink/Cursor Control Register*/
+	{S1DREG_LCD_CUR_START,		0x01},	/* LCD Ink/Cursor Start Address Register*/
+	{S1DREG_LCD_CUR_XPOS0,		0x00},	/* LCD Cursor X Position Register 0*/
+	{S1DREG_LCD_CUR_XPOS1,		0x00},	/* LCD Cursor X Position Register 1*/
+	{S1DREG_LCD_CUR_YPOS0,		0x00},	/* LCD Cursor Y Position Register 0*/
+	{S1DREG_LCD_CUR_YPOS1,		0x00},	/* LCD Cursor Y Position Register 1*/
+	{S1DREG_LCD_CUR_BCTL0,		0x00},	/* LCD Ink/Cursor Blue Color 0 Register*/
+	{S1DREG_LCD_CUR_GCTL0,		0x00},	/* LCD Ink/Cursor Green Color 0 Register*/
+	{S1DREG_LCD_CUR_RCTL0,		0x00},	/* LCD Ink/Cursor Red Color 0 Register*/
+	{S1DREG_LCD_CUR_BCTL1,		0x1F},	/* LCD Ink/Cursor Blue Color 1 Register*/
+	{S1DREG_LCD_CUR_GCTL1,		0x3F},	/* LCD Ink/Cursor Green Color 1 Register*/
+	{S1DREG_LCD_CUR_RCTL1,		0x1F},	/* LCD Ink/Cursor Red Color 1 Register*/
+	{S1DREG_LCD_CUR_FIFO_HTC,	0x00},	/* LCD Ink/Cursor FIFO Threshold Register*/
+	{S1DREG_CRT_CUR_CTL,		0x00},	/* CRT/TV Ink/Cursor Control Register*/
+	{S1DREG_CRT_CUR_START,		0x01},	/* CRT/TV Ink/Cursor Start Address Register*/
+	{S1DREG_CRT_CUR_XPOS0,		0x00},	/* CRT/TV Cursor X Position Register 0*/
+	{S1DREG_CRT_CUR_XPOS1,		0x00},	/* CRT/TV Cursor X Position Register 1*/
+	{S1DREG_CRT_CUR_YPOS0,		0x00},	/* CRT/TV Cursor Y Position Register 0*/
+	{S1DREG_CRT_CUR_YPOS1,		0x00},	/* CRT/TV Cursor Y Position Register 1*/
+	{S1DREG_CRT_CUR_BCTL0,		0x00},	/* CRT/TV Ink/Cursor Blue Color 0 Register*/
+	{S1DREG_CRT_CUR_GCTL0,		0x00},	/* CRT/TV Ink/Cursor Green Color 0 Register*/
+	{S1DREG_CRT_CUR_RCTL0,		0x00},	/* CRT/TV Ink/Cursor Red Color 0 Register*/
+	{S1DREG_CRT_CUR_BCTL1,		0x1F},	/* CRT/TV Ink/Cursor Blue Color 1 Register*/
+	{S1DREG_CRT_CUR_GCTL1,		0x3F},	/* CRT/TV Ink/Cursor Green Color 1 Register*/
+	{S1DREG_CRT_CUR_RCTL1,		0x1F},	/* CRT/TV Ink/Cursor Red Color 1 Register*/
+	{S1DREG_CRT_CUR_FIFO_HTC,	0x00},	/* CRT/TV Ink/Cursor FIFO Threshold Register*/
+	{S1DREG_BBLT_CTL0,		0x00},	/* BitBlt Control Register 0*/
+	{S1DREG_BBLT_CTL1,		0x01},	/* BitBlt Control Register 1*/
+	{S1DREG_BBLT_CC_EXP,		0x00},	/* BitBlt ROP Code/Color Expansion Register*/
+	{S1DREG_BBLT_OP,		0x00},	/* BitBlt Operation Register*/
+	{S1DREG_BBLT_SRC_START0,	0x00},	/* BitBlt Source Start Address Register 0*/
+	{S1DREG_BBLT_SRC_START1,	0x00},	/* BitBlt Source Start Address Register 1*/
+	{S1DREG_BBLT_SRC_START2,	0x00},	/* BitBlt Source Start Address Register 2*/
+	{S1DREG_BBLT_DST_START0,	0x00},	/* BitBlt Destination Start Address Register 0*/
+	{S1DREG_BBLT_DST_START1,	0x00},	/* BitBlt Destination Start Address Register 1*/
+	{S1DREG_BBLT_DST_START2,	0x00},	/* BitBlt Destination Start Address Register 2*/
+	{S1DREG_BBLT_MEM_OFF0,		0x00},	/* BitBlt Memory Address Offset Register 0*/
+	{S1DREG_BBLT_MEM_OFF1,		0x00},	/* BitBlt Memory Address Offset Register 1*/
+	{S1DREG_BBLT_WIDTH0,		0x00},	/* BitBlt Width Register 0*/
+	{S1DREG_BBLT_WIDTH1,		0x00},	/* BitBlt Width Register 1*/
+	{S1DREG_BBLT_HEIGHT0,		0x00},	/* BitBlt Height Register 0*/
+	{S1DREG_BBLT_HEIGHT1,		0x00},	/* BitBlt Height Register 1*/
+	{S1DREG_BBLT_BGC0,		0x00},	/* BitBlt Background Color Register 0*/
+	{S1DREG_BBLT_BGC1,		0x00},	/* BitBlt Background Color Register 1*/
+	{S1DREG_BBLT_FGC0,		0x00},	/* BitBlt Foreground Color Register 0*/
+	{S1DREG_BBLT_FGC1,		0x00},	/* BitBlt Foreground Color Register 1*/
+	{S1DREG_LKUP_MODE,		0x00},	/* Look-Up Table Mode Register*/
+	{S1DREG_LKUP_ADDR,		0x00},	/* Look-Up Table Address Register*/
+	{S1DREG_PS_CNF,			0x00},	/* Power Save Configuration Register*/
+	{S1DREG_PS_STATUS,		0x00},	/* Power Save Status Register*/
+	{S1DREG_CPU2MEM_WDOGT,		0x00},	/* CPU-to-Memory Access Watchdog Timer Register*/
+	{S1DREG_COM_DISP_MODE,		0x01},	/* Display Mode Register, LCD only*/
 };
 
-static u64 s1dfb_dmamask = 0xffffffffUL;
+static u64 s1dfb_dmamask = DMA_BIT_MASK(32);
 
-static struct s1d13xxxfb_pdata yl_9200_s1dfb_pdata = {
-		.initregs				= yl_9200_s1dfb_initregs,
-		.initregssize			= ARRAY_SIZE(yl_9200_s1dfb_initregs),
-		.platform_init_video	= yl_9200_init_video,
+static struct s1d13xxxfb_pdata yl9200_s1dfb_pdata = {
+	.initregs		= yl9200_s1dfb_initregs,
+	.initregssize		= ARRAY_SIZE(yl9200_s1dfb_initregs),
+	.platform_init_video	= yl9200_init_video,
 };
 
-static struct resource yl_9200_s1dfb_resource[] = {
+static struct resource yl9200_s1dfb_resource[] = {
 	[0] = {	/* video mem */
-		.name   = "s1d13xxxfb memory",
-	/*	.name   = "s1d13806 memory",*/
-		.start  = AT91_FB_VMEM_BASE,
-		.end    = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
-		.flags  = IORESOURCE_MEM,
+		.name	= "s1d13xxxfb memory",
+		.start	= AT91_FB_VMEM_BASE,
+		.end	= AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
+		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {	/* video registers */
-		.name   = "s1d13xxxfb registers",
-	/*	.name   = "s1d13806 registers",*/
-		.start  = AT91_FB_REG_BASE,
-		.end    = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
-		.flags  = IORESOURCE_MEM,
+		.name	= "s1d13xxxfb registers",
+		.start	= AT91_FB_REG_BASE,
+		.end	= AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
+		.flags	= IORESOURCE_MEM,
 	},
 };
 
-static struct platform_device yl_9200_s1dfb_device = {
-	/*TODO S.Birtles , really we need the chip revision in here as well*/
-		.name		= "s1d13806fb",
-	/*  .name		= "s1d13506fb",*/
-		.id			= -1,
-		.dev		= {
-	/*TODO theres a waring here!!*/
-	/*WARNING: vmlinux.o(.data+0x2dbc): Section mismatch: reference to .init.text: (between 'yl_9200_s1dfb_pdata' and 's1dfb_dmamask')*/
+static struct platform_device yl9200_s1dfb_device = {
+	.name		= "s1d13806fb",
+	.id		= -1,
+	.dev	= {
 		.dma_mask		= &s1dfb_dmamask,
-		.coherent_dma_mask	= 0xffffffff,
-		.platform_data		= &yl_9200_s1dfb_pdata,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &yl9200_s1dfb_pdata,
 	},
-	.resource	= yl_9200_s1dfb_resource,
-	.num_resources	= ARRAY_SIZE(yl_9200_s1dfb_resource),
+	.resource	= yl9200_s1dfb_resource,
+	.num_resources	= ARRAY_SIZE(yl9200_s1dfb_resource),
 };
 
-void __init yl_9200_add_device_video(void)
+void __init yl9200_add_device_video(void)
 {
-	platform_device_register(&yl_9200_s1dfb_device);
+	platform_device_register(&yl9200_s1dfb_device);
 }
 #else
-	void __init yl_9200_add_device_video(void) {}
+void __init yl9200_add_device_video(void) {}
 #endif
 
-/*this is not called first , yl_9200_map_io is called first*/
-static void __init yl_9200_board_init(void)
+
+static void __init yl9200_board_init(void)
 {
 	/* Serial */
 	at91_add_device_serial();
 	/* Ethernet */
-	at91_add_device_eth(&yl_9200_eth_data);
+	at91_add_device_eth(&yl9200_eth_data);
 	/* USB Host */
-	at91_add_device_usbh(&yl_9200_usbh_data);
+	at91_add_device_usbh(&yl9200_usbh_data);
 	/* USB Device */
-	at91_add_device_udc(&yl_9200_udc_data);
-	/* pullup_pin it is  actually active low, but this is not needed, driver sets it up */
-	/*at91_set_multi_drive(yl_9200_udc_data.pullup_pin, 0);*/
-
-	/* Compact Flash */
-	/*at91_add_device_cf(&yl_9200_cf_data);*/
-
+	at91_add_device_udc(&yl9200_udc_data);
 	/* I2C */
-	at91_add_device_i2c(yl_9200_i2c_devices, ARRAY_SIZE(yl_9200_i2c_devices));
-	/* SPI */
-	/*TODO YL9200 we have 2 spi interfaces touch screen & CAN*/
-	/* AT91_PIN_PA5, AT91_PIN_PA6 , are used on the  max 485 NOT SPI*/
-
-	/*touch screen and CAN*/
-	at91_add_device_spi(yl_9200_spi_devices, ARRAY_SIZE(yl_9200_spi_devices));
-
-	/*Basically the  TS uses  PB11 & PB10 , PB11 is configured by the SPI system BP10 IS NOT USED!!*/
-	/* we need this incase the board is running without a touch screen*/
-	#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	at91_init_device_ts(); /*init the touch screen device*/
-	#endif
-	/* DataFlash card */
-	at91_add_device_mmc(0, &yl_9200_mmc_data);
+	at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices));
+	/* MMC */
+	at91_add_device_mmc(0, &yl9200_mmc_data);
 	/* NAND */
-	at91_add_device_nand(&yl_9200_nand_data);
+	at91_add_device_nand(&yl9200_nand_data);
 	/* NOR Flash */
-	platform_device_register(&yl_9200_flash);
-	/* LEDs. Note!! this does not include the led's we passed for the processor status */
-	at91_gpio_leds(yl_9200_leds, ARRAY_SIZE(yl_9200_leds));
-	/* VGA  */
-	/*this is self registered by including the s1d13xxx chip in the kernel build*/
-	yl_9200_add_device_video();
+	platform_device_register(&yl9200_flash);
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+	/* SPI */
+	at91_add_device_spi(yl9200_spi_devices, ARRAY_SIZE(yl9200_spi_devices));
+	/* Touchscreen */
+	yl9200_add_device_ts();
+#endif
+	/* LEDs. */
+	at91_gpio_leds(yl9200_leds, ARRAY_SIZE(yl9200_leds));
 	/* Push Buttons */
-	yl_9200_add_device_buttons();
-	/*TODO fixup the Sounder */
-//	yl_9200_add_device_sounder(yl_9200_sounder,ARRAY_SIZE(yl_9200_sounder));
-
+	yl9200_add_device_buttons();
+	/* VGA */
+	yl9200_add_device_video();
 }
 
 MACHINE_START(YL9200, "uCdragon YL-9200")
-	/* Maintainer: S.Birtles*/
-	.phys_io		= AT91_BASE_SYS,
+	/* Maintainer: S.Birtles */
+	.phys_io	= AT91_BASE_SYS,
 	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
 	.boot_params	= AT91_SDRAM_BASE + 0x100,
-	.timer			= &at91rm9200_timer,
-	.map_io			= yl_9200_map_io,
-	.init_irq		= yl_9200_init_irq,
-	.init_machine	= yl_9200_board_init,
+	.timer		= &at91rm9200_timer,
+	.map_io		= yl9200_map_io,
+	.init_irq	= yl9200_init_irq,
+	.init_machine	= yl9200_board_init,
 MACHINE_END