gma500: initial medfield merge

We need to merge this ahead of some of the cleanup because a lot of needed
cleanup spans both new and old chips. If we try and clean up and the merge
we end up fighting ourselves.

Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[With a load of the cleanup stuff folded in, register stuff reworked sanely]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

22 files changed, 6345 insertions, 0 deletions

diff --git a/arch/x86/platform/mrst/mrst.c b/arch/x86/platform/mrst/mrst.c
index 475e2cd0f3c..b930cc43a23 100644
--- a/arch/x86/platform/mrst/mrst.c
+++ b/arch/x86/platform/mrst/mrst.c
@@ -28,6 +28,8 @@
 #include <linux/module.h>
 #include <linux/notifier.h>
 #include <linux/mfd/intel_msic.h>
+#include <linux/gpio.h>
+#include <linux/i2c/tc35876x.h>
 
 #include <asm/setup.h>
 #include <asm/mpspec_def.h>
@@ -686,6 +688,19 @@ static void *msic_ocd_platform_data(void *info)
 	return msic_generic_platform_data(info, INTEL_MSIC_BLOCK_OCD);
 }
 
+/* tc35876x DSI-LVDS bridge chip and panel platform data */
+static void *tc35876x_platform_data(void *data)
+{
+       static struct tc35876x_platform_data pdata;
+
+       /* gpio pins set to -1 will not be used by the driver */
+       pdata.gpio_bridge_reset = get_gpio_by_name("LCMB_RXEN");
+       pdata.gpio_panel_bl_en = get_gpio_by_name("6S6P_BL_EN");
+       pdata.gpio_panel_vadd = get_gpio_by_name("EN_VREG_LCD_V3P3");
+
+       return &pdata;
+}
+
 static const struct devs_id __initconst device_ids[] = {
 	{"bma023", SFI_DEV_TYPE_I2C, 1, &no_platform_data},
 	{"pmic_gpio", SFI_DEV_TYPE_SPI, 1, &pmic_gpio_platform_data},
@@ -698,6 +713,7 @@ static const struct devs_id __initconst device_ids[] = {
 	{"i2c_accel", SFI_DEV_TYPE_I2C, 0, &lis331dl_platform_data},
 	{"pmic_audio", SFI_DEV_TYPE_IPC, 1, &no_platform_data},
 	{"mpu3050", SFI_DEV_TYPE_I2C, 1, &mpu3050_platform_data},
+	{"i2c_disp_brig", SFI_DEV_TYPE_I2C, 0, &tc35876x_platform_data},
 
 	/* MSIC subdevices */
 	{"msic_battery", SFI_DEV_TYPE_IPC, 1, &msic_battery_platform_data},
diff --git a/drivers/gpu/drm/gma500/Kconfig b/drivers/gpu/drm/gma500/Kconfig
index f92a7f4208d..42e665c7e90 100644
--- a/drivers/gpu/drm/gma500/Kconfig
+++ b/drivers/gpu/drm/gma500/Kconfig
@@ -24,3 +24,10 @@ config DRM_GMA3600
 	help
 	  Say yes to include basic support for Intel GMA3600/3650 (Intel
 	  Cedar Trail) platforms.
+
+config DRM_MEDFIELD
+	bool "Intel Medfield support (Experimental)"
+	depends on DRM_GMA500 && X86_INTEL_MID
+	help
+	  Say yes to include support for the Intel Medfield platform.
+
diff --git a/drivers/gpu/drm/gma500/Makefile b/drivers/gpu/drm/gma500/Makefile
index 81c103be5e2..1583982917c 100644
--- a/drivers/gpu/drm/gma500/Makefile
+++ b/drivers/gpu/drm/gma500/Makefile
@@ -37,4 +37,14 @@ gma500_gfx-$(CONFIG_DRM_GMA600) += oaktrail_device.o \
 	  oaktrail_hdmi.o \
 	  oaktrail_hdmi_i2c.o
 
+gma500_gfx-$(CONFIG_DRM_MEDFIELD) += mdfld_device.o \
+	  mdfld_output.o \
+	  mdfld_intel_display.o \
+	  mdfld_dsi_output.o \
+	  mdfld_dsi_dpi.o \
+	  mdfld_dsi_pkg_sender.o \
+	  mdfld_tpo_vid.o \
+	  mdfld_tmd_vid.o \
+	  tc35876x-dsi-lvds.o
+
 obj-$(CONFIG_DRM_GMA500) += gma500_gfx.o
diff --git a/drivers/gpu/drm/gma500/mdfld_device.c b/drivers/gpu/drm/gma500/mdfld_device.c
new file mode 100644
index 00000000000..6cfdda90eef
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_device.c
@@ -0,0 +1,691 @@
+/**************************************************************************
+ * Copyright (c) 2011, Intel Corporation.
+ * All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ **************************************************************************/
+
+#include "psb_drv.h"
+#include "mid_bios.h"
+#include "mdfld_output.h"
+#include "mdfld_dsi_output.h"
+#include "tc35876x-dsi-lvds.h"
+
+#include <asm/intel_scu_ipc.h>
+
+#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
+
+#define MRST_BLC_MAX_PWM_REG_FREQ	    0xFFFF
+#define BLC_PWM_PRECISION_FACTOR 100	/* 10000000 */
+#define BLC_PWM_FREQ_CALC_CONSTANT 32
+#define MHz 1000000
+#define BRIGHTNESS_MIN_LEVEL 1
+#define BRIGHTNESS_MAX_LEVEL 100
+#define BRIGHTNESS_MASK	0xFF
+#define BLC_POLARITY_NORMAL 0
+#define BLC_POLARITY_INVERSE 1
+#define BLC_ADJUSTMENT_MAX 100
+
+#define MDFLD_BLC_PWM_PRECISION_FACTOR    10
+#define MDFLD_BLC_MAX_PWM_REG_FREQ        0xFFFE
+#define MDFLD_BLC_MIN_PWM_REG_FREQ        0x2
+
+#define MDFLD_BACKLIGHT_PWM_POLARITY_BIT_CLEAR (0xFFFE)
+#define MDFLD_BACKLIGHT_PWM_CTL_SHIFT	(16)
+
+static struct backlight_device *mdfld_backlight_device;
+
+int mdfld_set_brightness(struct backlight_device *bd)
+{
+	struct drm_device *dev =
+		(struct drm_device *)bl_get_data(mdfld_backlight_device);
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	int level = bd->props.brightness;
+
+	DRM_DEBUG_DRIVER("backlight level set to %d\n", level);
+
+	/* Perform value bounds checking */
+	if (level < BRIGHTNESS_MIN_LEVEL)
+		level = BRIGHTNESS_MIN_LEVEL;
+
+	if (gma_power_begin(dev, false)) {
+		u32 adjusted_level = 0;
+
+		/*
+		 * Adjust the backlight level with the percent in
+		 * dev_priv->blc_adj2
+		 */
+		adjusted_level = level * dev_priv->blc_adj2;
+		adjusted_level = adjusted_level / BLC_ADJUSTMENT_MAX;
+		dev_priv->brightness_adjusted = adjusted_level;
+
+		if (mdfld_get_panel_type(dev, 0) == TC35876X) {
+			if (dev_priv->dpi_panel_on[0] ||
+					dev_priv->dpi_panel_on[2])
+				tc35876x_brightness_control(dev,
+						dev_priv->brightness_adjusted);
+		} else {
+			if (dev_priv->dpi_panel_on[0])
+				mdfld_dsi_brightness_control(dev, 0,
+						dev_priv->brightness_adjusted);
+		}
+
+		if (dev_priv->dpi_panel_on[2])
+			mdfld_dsi_brightness_control(dev, 2,
+					dev_priv->brightness_adjusted);
+		gma_power_end(dev);
+	}
+
+	/* cache the brightness for later use */
+	dev_priv->brightness = level;
+	return 0;
+}
+
+int mdfld_get_brightness(struct backlight_device *bd)
+{
+	struct drm_device *dev =
+		(struct drm_device *)bl_get_data(mdfld_backlight_device);
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	DRM_DEBUG_DRIVER("brightness = 0x%x \n", dev_priv->brightness);
+
+	/* return locally cached var instead of HW read (due to DPST etc.) */
+	return dev_priv->brightness;
+}
+
+static const struct backlight_ops mdfld_ops = {
+	.get_brightness = mdfld_get_brightness,
+	.update_status  = mdfld_set_brightness,
+};
+
+static int device_backlight_init(struct drm_device *dev)
+{
+	struct drm_psb_private *dev_priv = (struct drm_psb_private *)
+		dev->dev_private;
+
+	dev_priv->blc_adj1 = BLC_ADJUSTMENT_MAX;
+	dev_priv->blc_adj2 = BLC_ADJUSTMENT_MAX;
+
+	return 0;
+}
+
+int mdfld_backlight_init(struct drm_device *dev)
+{
+	struct backlight_properties props;
+	int ret = 0;
+
+	memset(&props, 0, sizeof(struct backlight_properties));
+	props.max_brightness = BRIGHTNESS_MAX_LEVEL;
+	props.type = BACKLIGHT_PLATFORM;
+	mdfld_backlight_device = backlight_device_register("mdfld-bl",
+				NULL, (void *)dev, &mdfld_ops, &props);
+
+	if (IS_ERR(mdfld_backlight_device))
+		return PTR_ERR(mdfld_backlight_device);
+
+	ret = device_backlight_init(dev);
+	if (ret)
+		return ret;
+
+	mdfld_backlight_device->props.brightness = BRIGHTNESS_MAX_LEVEL;
+	mdfld_backlight_device->props.max_brightness = BRIGHTNESS_MAX_LEVEL;
+	backlight_update_status(mdfld_backlight_device);
+	return 0;
+}
+#endif
+
+struct backlight_device *mdfld_get_backlight_device(void)
+{
+#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
+	return mdfld_backlight_device;
+#else
+	return NULL;
+#endif
+}
+
+/*
+ * mdfld_save_display_registers
+ *
+ * Description: We are going to suspend so save current display
+ * register state.
+ *
+ * Notes: FIXME_JLIU7 need to add the support for DPI MIPI & HDMI audio
+ */
+static int mdfld_save_display_registers(struct drm_device *dev, int pipe)
+{
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	struct medfield_state *regs = &dev_priv->regs.mdfld;
+	int i;
+
+	/* register */
+	u32 dpll_reg = MRST_DPLL_A;
+	u32 fp_reg = MRST_FPA0;
+	u32 pipeconf_reg = PIPEACONF;
+	u32 htot_reg = HTOTAL_A;
+	u32 hblank_reg = HBLANK_A;
+	u32 hsync_reg = HSYNC_A;
+	u32 vtot_reg = VTOTAL_A;
+	u32 vblank_reg = VBLANK_A;
+	u32 vsync_reg = VSYNC_A;
+	u32 pipesrc_reg = PIPEASRC;
+	u32 dspstride_reg = DSPASTRIDE;
+	u32 dsplinoff_reg = DSPALINOFF;
+	u32 dsptileoff_reg = DSPATILEOFF;
+	u32 dspsize_reg = DSPASIZE;
+	u32 dsppos_reg = DSPAPOS;
+	u32 dspsurf_reg = DSPASURF;
+	u32 mipi_reg = MIPI;
+	u32 dspcntr_reg = DSPACNTR;
+	u32 dspstatus_reg = PIPEASTAT;
+	u32 palette_reg = PALETTE_A;
+
+	/* pointer to values */
+	u32 *dpll_val = &regs->saveDPLL_A;
+	u32 *fp_val = &regs->saveFPA0;
+	u32 *pipeconf_val = &regs->savePIPEACONF;
+	u32 *htot_val = &regs->saveHTOTAL_A;
+	u32 *hblank_val = &regs->saveHBLANK_A;
+	u32 *hsync_val = &regs->saveHSYNC_A;
+	u32 *vtot_val = &regs->saveVTOTAL_A;
+	u32 *vblank_val = &regs->saveVBLANK_A;
+	u32 *vsync_val = &regs->saveVSYNC_A;
+	u32 *pipesrc_val = &regs->savePIPEASRC;
+	u32 *dspstride_val = &regs->saveDSPASTRIDE;
+	u32 *dsplinoff_val = &regs->saveDSPALINOFF;
+	u32 *dsptileoff_val = &regs->saveDSPATILEOFF;
+	u32 *dspsize_val = &regs->saveDSPASIZE;
+	u32 *dsppos_val = &regs->saveDSPAPOS;
+	u32 *dspsurf_val = &regs->saveDSPASURF;
+	u32 *mipi_val = &regs->saveMIPI;
+	u32 *dspcntr_val = &regs->saveDSPACNTR;
+	u32 *dspstatus_val = &regs->saveDSPASTATUS;
+	u32 *palette_val = regs->save_palette_a;
+
+	switch (pipe) {
+	case 0:
+		break;
+	case 1:
+		/* regester */
+		dpll_reg = MDFLD_DPLL_B;
+		fp_reg = MDFLD_DPLL_DIV0;
+		pipeconf_reg = PIPEBCONF;
+		htot_reg = HTOTAL_B;
+		hblank_reg = HBLANK_B;
+		hsync_reg = HSYNC_B;
+		vtot_reg = VTOTAL_B;
+		vblank_reg = VBLANK_B;
+		vsync_reg = VSYNC_B;
+		pipesrc_reg = PIPEBSRC;
+		dspstride_reg = DSPBSTRIDE;
+		dsplinoff_reg = DSPBLINOFF;
+		dsptileoff_reg = DSPBTILEOFF;
+		dspsize_reg = DSPBSIZE;
+		dsppos_reg = DSPBPOS;
+		dspsurf_reg = DSPBSURF;
+		dspcntr_reg = DSPBCNTR;
+		dspstatus_reg = PIPEBSTAT;
+		palette_reg = PALETTE_B;
+
+		/* values */
+		dpll_val = &regs->saveDPLL_B;
+		fp_val = &regs->saveFPB0;
+		pipeconf_val = &regs->savePIPEBCONF;
+		htot_val = &regs->saveHTOTAL_B;
+		hblank_val = &regs->saveHBLANK_B;
+		hsync_val = &regs->saveHSYNC_B;
+		vtot_val = &regs->saveVTOTAL_B;
+		vblank_val = &regs->saveVBLANK_B;
+		vsync_val = &regs->saveVSYNC_B;
+		pipesrc_val = &regs->savePIPEBSRC;
+		dspstride_val = &regs->saveDSPBSTRIDE;
+		dsplinoff_val = &regs->saveDSPBLINOFF;
+		dsptileoff_val = &regs->saveDSPBTILEOFF;
+		dspsize_val = &regs->saveDSPBSIZE;
+		dsppos_val = &regs->saveDSPBPOS;
+		dspsurf_val = &regs->saveDSPBSURF;
+		dspcntr_val = &regs->saveDSPBCNTR;
+		dspstatus_val = &regs->saveDSPBSTATUS;
+		palette_val = regs->save_palette_b;
+		break;
+	case 2:
+		/* register */
+		pipeconf_reg = PIPECCONF;
+		htot_reg = HTOTAL_C;
+		hblank_reg = HBLANK_C;
+		hsync_reg = HSYNC_C;
+		vtot_reg = VTOTAL_C;
+		vblank_reg = VBLANK_C;
+		vsync_reg = VSYNC_C;
+		pipesrc_reg = PIPECSRC;
+		dspstride_reg = DSPCSTRIDE;
+		dsplinoff_reg = DSPCLINOFF;
+		dsptileoff_reg = DSPCTILEOFF;
+		dspsize_reg = DSPCSIZE;
+		dsppos_reg = DSPCPOS;
+		dspsurf_reg = DSPCSURF;
+		mipi_reg = MIPI_C;
+		dspcntr_reg = DSPCCNTR;
+		dspstatus_reg = PIPECSTAT;
+		palette_reg = PALETTE_C;
+
+		/* pointer to values */
+		pipeconf_val = &regs->savePIPECCONF;
+		htot_val = &regs->saveHTOTAL_C;
+		hblank_val = &regs->saveHBLANK_C;
+		hsync_val = &regs->saveHSYNC_C;
+		vtot_val = &regs->saveVTOTAL_C;
+		vblank_val = &regs->saveVBLANK_C;
+		vsync_val = &regs->saveVSYNC_C;
+		pipesrc_val = &regs->savePIPECSRC;
+		dspstride_val = &regs->saveDSPCSTRIDE;
+		dsplinoff_val = &regs->saveDSPCLINOFF;
+		dsptileoff_val = &regs->saveDSPCTILEOFF;
+		dspsize_val = &regs->saveDSPCSIZE;
+		dsppos_val = &regs->saveDSPCPOS;
+		dspsurf_val = &regs->saveDSPCSURF;
+		mipi_val = &regs->saveMIPI_C;
+		dspcntr_val = &regs->saveDSPCCNTR;
+		dspstatus_val = &regs->saveDSPCSTATUS;
+		palette_val = regs->save_palette_c;
+		break;
+	default:
+		DRM_ERROR("%s, invalid pipe number.\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Pipe & plane A info */
+	*dpll_val = PSB_RVDC32(dpll_reg);
+	*fp_val = PSB_RVDC32(fp_reg);
+	*pipeconf_val = PSB_RVDC32(pipeconf_reg);
+	*htot_val = PSB_RVDC32(htot_reg);
+	*hblank_val = PSB_RVDC32(hblank_reg);
+	*hsync_val = PSB_RVDC32(hsync_reg);
+	*vtot_val = PSB_RVDC32(vtot_reg);
+	*vblank_val = PSB_RVDC32(vblank_reg);
+	*vsync_val = PSB_RVDC32(vsync_reg);
+	*pipesrc_val = PSB_RVDC32(pipesrc_reg);
+	*dspstride_val = PSB_RVDC32(dspstride_reg);
+	*dsplinoff_val = PSB_RVDC32(dsplinoff_reg);
+	*dsptileoff_val = PSB_RVDC32(dsptileoff_reg);
+	*dspsize_val = PSB_RVDC32(dspsize_reg);
+	*dsppos_val = PSB_RVDC32(dsppos_reg);
+	*dspsurf_val = PSB_RVDC32(dspsurf_reg);
+	*dspcntr_val = PSB_RVDC32(dspcntr_reg);
+	*dspstatus_val = PSB_RVDC32(dspstatus_reg);
+
+	/*save palette (gamma) */
+	for (i = 0; i < 256; i++)
+		palette_val[i] = PSB_RVDC32(palette_reg + (i << 2));
+
+	if (pipe == 1) {
+		regs->savePFIT_CONTROL = PSB_RVDC32(PFIT_CONTROL);
+		regs->savePFIT_PGM_RATIOS = PSB_RVDC32(PFIT_PGM_RATIOS);
+
+		regs->saveHDMIPHYMISCCTL = PSB_RVDC32(HDMIPHYMISCCTL);
+		regs->saveHDMIB_CONTROL = PSB_RVDC32(HDMIB_CONTROL);
+		return 0;
+	}
+
+	*mipi_val = PSB_RVDC32(mipi_reg);
+	return 0;
+}
+
+/*
+ * mdfld_restore_display_registers
+ *
+ * Description: We are going to resume so restore display register state.
+ *
+ * Notes: FIXME_JLIU7 need to add the support for DPI MIPI & HDMI audio
+ */
+static int mdfld_restore_display_registers(struct drm_device *dev, int pipe)
+{
+	/* To get  panel out of ULPS mode. */
+	u32 temp = 0;
+	u32 device_ready_reg = DEVICE_READY_REG;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	struct mdfld_dsi_config *dsi_config = NULL;
+	struct medfield_state *regs = &dev_priv->regs.mdfld;
+	u32 i = 0;
+	u32 dpll = 0;
+	u32 timeout = 0;
+
+	/* regester */
+	u32 dpll_reg = MRST_DPLL_A;
+	u32 fp_reg = MRST_FPA0;
+	u32 pipeconf_reg = PIPEACONF;
+	u32 htot_reg = HTOTAL_A;
+	u32 hblank_reg = HBLANK_A;
+	u32 hsync_reg = HSYNC_A;
+	u32 vtot_reg = VTOTAL_A;
+	u32 vblank_reg = VBLANK_A;
+	u32 vsync_reg = VSYNC_A;
+	u32 pipesrc_reg = PIPEASRC;
+	u32 dspstride_reg = DSPASTRIDE;
+	u32 dsplinoff_reg = DSPALINOFF;
+	u32 dsptileoff_reg = DSPATILEOFF;
+	u32 dspsize_reg = DSPASIZE;
+	u32 dsppos_reg = DSPAPOS;
+	u32 dspsurf_reg = DSPASURF;
+	u32 dspstatus_reg = PIPEASTAT;
+	u32 mipi_reg = MIPI;
+	u32 dspcntr_reg = DSPACNTR;
+	u32 palette_reg = PALETTE_A;
+
+	/* values */
+	u32 dpll_val = regs->saveDPLL_A & ~DPLL_VCO_ENABLE;
+	u32 fp_val = regs->saveFPA0;
+	u32 pipeconf_val = regs->savePIPEACONF;
+	u32 htot_val = regs->saveHTOTAL_A;
+	u32 hblank_val = regs->saveHBLANK_A;
+	u32 hsync_val = regs->saveHSYNC_A;
+	u32 vtot_val = regs->saveVTOTAL_A;
+	u32 vblank_val = regs->saveVBLANK_A;
+	u32 vsync_val = regs->saveVSYNC_A;
+	u32 pipesrc_val = regs->savePIPEASRC;
+	u32 dspstride_val = regs->saveDSPASTRIDE;
+	u32 dsplinoff_val = regs->saveDSPALINOFF;
+	u32 dsptileoff_val = regs->saveDSPATILEOFF;
+	u32 dspsize_val = regs->saveDSPASIZE;
+	u32 dsppos_val = regs->saveDSPAPOS;
+	u32 dspsurf_val = regs->saveDSPASURF;
+	u32 dspstatus_val = regs->saveDSPASTATUS;
+	u32 mipi_val = regs->saveMIPI;
+	u32 dspcntr_val = regs->saveDSPACNTR;
+	u32 *palette_val = regs->save_palette_a;
+
+	switch (pipe) {
+	case 0:
+		dsi_config = dev_priv->dsi_configs[0];
+		break;
+	case 1:
+		/* regester */
+		dpll_reg = MDFLD_DPLL_B;
+		fp_reg = MDFLD_DPLL_DIV0;
+		pipeconf_reg = PIPEBCONF;
+		htot_reg = HTOTAL_B;
+		hblank_reg = HBLANK_B;
+		hsync_reg = HSYNC_B;
+		vtot_reg = VTOTAL_B;
+		vblank_reg = VBLANK_B;
+		vsync_reg = VSYNC_B;
+		pipesrc_reg = PIPEBSRC;
+		dspstride_reg = DSPBSTRIDE;
+		dsplinoff_reg = DSPBLINOFF;
+		dsptileoff_reg = DSPBTILEOFF;
+		dspsize_reg = DSPBSIZE;
+		dsppos_reg = DSPBPOS;
+		dspsurf_reg = DSPBSURF;
+		dspcntr_reg = DSPBCNTR;
+		dspstatus_reg = PIPEBSTAT;
+		palette_reg = PALETTE_B;
+
+		/* values */
+		dpll_val = regs->saveDPLL_B & ~DPLL_VCO_ENABLE;
+		fp_val = regs->saveFPB0;
+		pipeconf_val = regs->savePIPEBCONF;
+		htot_val = regs->saveHTOTAL_B;
+		hblank_val = regs->saveHBLANK_B;
+		hsync_val = regs->saveHSYNC_B;
+		vtot_val = regs->saveVTOTAL_B;
+		vblank_val = regs->saveVBLANK_B;
+		vsync_val = regs->saveVSYNC_B;
+		pipesrc_val = regs->savePIPEBSRC;
+		dspstride_val = regs->saveDSPBSTRIDE;
+		dsplinoff_val = regs->saveDSPBLINOFF;
+		dsptileoff_val = regs->saveDSPBTILEOFF;
+		dspsize_val = regs->saveDSPBSIZE;
+		dsppos_val = regs->saveDSPBPOS;
+		dspsurf_val = regs->saveDSPBSURF;
+		dspcntr_val = regs->saveDSPBCNTR;
+		dspstatus_val = regs->saveDSPBSTATUS;
+		palette_val = regs->save_palette_b;
+		break;
+	case 2:
+		/* regester */
+		pipeconf_reg = PIPECCONF;
+		htot_reg = HTOTAL_C;
+		hblank_reg = HBLANK_C;
+		hsync_reg = HSYNC_C;
+		vtot_reg = VTOTAL_C;
+		vblank_reg = VBLANK_C;
+		vsync_reg = VSYNC_C;
+		pipesrc_reg = PIPECSRC;
+		dspstride_reg = DSPCSTRIDE;
+		dsplinoff_reg = DSPCLINOFF;
+		dsptileoff_reg = DSPCTILEOFF;
+		dspsize_reg = DSPCSIZE;
+		dsppos_reg = DSPCPOS;
+		dspsurf_reg = DSPCSURF;
+		mipi_reg = MIPI_C;
+		dspcntr_reg = DSPCCNTR;
+		dspstatus_reg = PIPECSTAT;
+		palette_reg = PALETTE_C;
+
+		/* values */
+		pipeconf_val = regs->savePIPECCONF;
+		htot_val = regs->saveHTOTAL_C;
+		hblank_val = regs->saveHBLANK_C;
+		hsync_val = regs->saveHSYNC_C;
+		vtot_val = regs->saveVTOTAL_C;
+		vblank_val = regs->saveVBLANK_C;
+		vsync_val = regs->saveVSYNC_C;
+		pipesrc_val = regs->savePIPECSRC;
+		dspstride_val = regs->saveDSPCSTRIDE;
+		dsplinoff_val = regs->saveDSPCLINOFF;
+		dsptileoff_val = regs->saveDSPCTILEOFF;
+		dspsize_val = regs->saveDSPCSIZE;
+		dsppos_val = regs->saveDSPCPOS;
+		dspsurf_val = regs->saveDSPCSURF;
+		mipi_val = regs->saveMIPI_C;
+		dspcntr_val = regs->saveDSPCCNTR;
+		dspstatus_val = regs->saveDSPCSTATUS;
+		palette_val = regs->save_palette_c;
+
+		dsi_config = dev_priv->dsi_configs[1];
+		break;
+	default:
+		DRM_ERROR("%s, invalid pipe number.\n", __func__);
+		return -EINVAL;
+	}
+
+	/*make sure VGA plane is off. it initializes to on after reset!*/
+	PSB_WVDC32(0x80000000, VGACNTRL);
+
+	if (pipe == 1) {
+		PSB_WVDC32(dpll_val & ~DPLL_VCO_ENABLE, dpll_reg);
+		PSB_RVDC32(dpll_reg);
+
+		PSB_WVDC32(fp_val, fp_reg);
+	} else {
+
+		dpll = PSB_RVDC32(dpll_reg);
+
+		if (!(dpll & DPLL_VCO_ENABLE)) {
+
+			/* When ungating power of DPLL, needs to wait 0.5us
+			   before enable the VCO */
+			if (dpll & MDFLD_PWR_GATE_EN) {
+				dpll &= ~MDFLD_PWR_GATE_EN;
+				PSB_WVDC32(dpll, dpll_reg);
+				/* FIXME_MDFLD PO - change 500 to 1 after PO */
+				udelay(500);
+			}
+
+			PSB_WVDC32(fp_val, fp_reg);
+			PSB_WVDC32(dpll_val, dpll_reg);
+			/* FIXME_MDFLD PO - change 500 to 1 after PO */
+			udelay(500);
+
+			dpll_val |= DPLL_VCO_ENABLE;
+			PSB_WVDC32(dpll_val, dpll_reg);
+			PSB_RVDC32(dpll_reg);
+
+			/* wait for DSI PLL to lock */
+			while (timeout < 20000 &&
+			  !(PSB_RVDC32(pipeconf_reg) & PIPECONF_DSIPLL_LOCK)) {
+				udelay(150);
+				timeout++;
+			}
+
+			if (timeout == 20000) {
+				DRM_ERROR("%s, can't lock DSIPLL.\n",
+								__func__);
+				return -EINVAL;
+			}
+		}
+	}
+	/* Restore mode */
+	PSB_WVDC32(htot_val, htot_reg);
+	PSB_WVDC32(hblank_val, hblank_reg);
+	PSB_WVDC32(hsync_val, hsync_reg);
+	PSB_WVDC32(vtot_val, vtot_reg);
+	PSB_WVDC32(vblank_val, vblank_reg);
+	PSB_WVDC32(vsync_val, vsync_reg);
+	PSB_WVDC32(pipesrc_val, pipesrc_reg);
+	PSB_WVDC32(dspstatus_val, dspstatus_reg);
+
+	/*set up the plane*/
+	PSB_WVDC32(dspstride_val, dspstride_reg);
+	PSB_WVDC32(dsplinoff_val, dsplinoff_reg);
+	PSB_WVDC32(dsptileoff_val, dsptileoff_reg);
+	PSB_WVDC32(dspsize_val, dspsize_reg);
+	PSB_WVDC32(dsppos_val, dsppos_reg);
+	PSB_WVDC32(dspsurf_val, dspsurf_reg);
+
+	if (pipe == 1) {
+		/* restore palette (gamma) */
+		/*DRM_UDELAY(50000); */
+		for (i = 0; i < 256; i++)
+			PSB_WVDC32(palette_val[i], palette_reg + (i << 2));
+
+		PSB_WVDC32(regs->savePFIT_CONTROL, PFIT_CONTROL);
+		PSB_WVDC32(regs->savePFIT_PGM_RATIOS, PFIT_PGM_RATIOS);
+
+		/*TODO: resume HDMI port */
+
+		/*TODO: resume pipe*/
+
+		/*enable the plane*/
+		PSB_WVDC32(dspcntr_val & ~DISPLAY_PLANE_ENABLE, dspcntr_reg);
+
+		return 0;
+	}
+
+	/*set up pipe related registers*/
+	PSB_WVDC32(mipi_val, mipi_reg);
+
+	/*setup MIPI adapter + MIPI IP registers*/
+	if (dsi_config)
+		mdfld_dsi_controller_init(dsi_config, pipe);
+
+	if (in_atomic() || in_interrupt())
+		mdelay(20);
+	else
+		msleep(20);
+
+	/*enable the plane*/
+	PSB_WVDC32(dspcntr_val, dspcntr_reg);
+
+	if (in_atomic() || in_interrupt())
+		mdelay(20);
+	else
+		msleep(20);
+
+	/* LP Hold Release */
+	temp = REG_READ(mipi_reg);
+	temp |= LP_OUTPUT_HOLD_RELEASE;
+	REG_WRITE(mipi_reg, temp);
+	mdelay(1);
+
+
+	/* Set DSI host to exit from Utra Low Power State */
+	temp = REG_READ(device_ready_reg);
+	temp &= ~ULPS_MASK;
+	temp |= 0x3;
+	temp |= EXIT_ULPS_DEV_READY;
+	REG_WRITE(device_ready_reg, temp);
+	mdelay(1);
+
+	temp = REG_READ(device_ready_reg);
+	temp &= ~ULPS_MASK;
+	temp |= EXITING_ULPS;
+	REG_WRITE(device_ready_reg, temp);
+	mdelay(1);
+
+	/*enable the pipe*/
+	PSB_WVDC32(pipeconf_val, pipeconf_reg);
+
+	/* restore palette (gamma) */
+	/*DRM_UDELAY(50000); */
+	for (i = 0; i < 256; i++)
+		PSB_WVDC32(palette_val[i], palette_reg + (i << 2));
+
+	return 0;
+}
+
+static int mdfld_save_registers(struct drm_device *dev)
+{
+	/* mdfld_save_cursor_overlay_registers(dev); */
+	mdfld_save_display_registers(dev, 0);
+	mdfld_save_display_registers(dev, 2);
+	mdfld_disable_crtc(dev, 0);
+	mdfld_disable_crtc(dev, 2);
+
+	return 0;
+}
+
+static int mdfld_restore_registers(struct drm_device *dev)
+{
+	mdfld_restore_display_registers(dev, 2);
+	mdfld_restore_display_registers(dev, 0);
+	/* mdfld_restore_cursor_overlay_registers(dev); */
+
+	return 0;
+}
+
+static int mdfld_power_down(struct drm_device *dev)
+{
+	/* FIXME */
+	return 0;
+}
+
+static int mdfld_power_up(struct drm_device *dev)
+{
+	/* FIXME */
+	return 0;
+}
+
+const struct psb_ops mdfld_chip_ops = {
+	.name = "mdfld",
+	.accel_2d = 0,
+	.pipes = 3,
+	.crtcs = 3,
+	.sgx_offset = MRST_SGX_OFFSET,
+
+	.chip_setup = mid_chip_setup,
+	.crtc_helper = &mdfld_helper_funcs,
+	.crtc_funcs = &psb_intel_crtc_funcs,
+
+	.output_init = mdfld_output_init,
+
+#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
+	.backlight_init = mdfld_backlight_init,
+#endif
+
+	.save_regs = mdfld_save_registers,
+	.restore_regs = mdfld_restore_registers,
+	.power_down = mdfld_power_down,
+	.power_up = mdfld_power_up,
+};
diff --git a/drivers/gpu/drm/gma500/mdfld_dsi_dpi.c b/drivers/gpu/drm/gma500/mdfld_dsi_dpi.c
new file mode 100644
index 00000000000..fc0df28a668
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_dsi_dpi.c
@@ -0,0 +1,1024 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * jim liu <jim.liu@intel.com>
+ * Jackie Li<yaodong.li@intel.com>
+ */
+
+#include "mdfld_dsi_dpi.h"
+#include "mdfld_output.h"
+#include "mdfld_dsi_pkg_sender.h"
+#include "psb_drv.h"
+#include "tc35876x-dsi-lvds.h"
+
+static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output,
+								int pipe);
+
+static void mdfld_wait_for_HS_DATA_FIFO(struct drm_device *dev, u32 pipe)
+{
+	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) &&
+		(REG_READ(gen_fifo_stat_reg) & DSI_FIFO_GEN_HS_DATA_FULL)) {
+		udelay(100);
+		timeout++;
+	}
+
+	if (timeout == 20000)
+		DRM_INFO("MIPI: HS Data FIFO was never cleared!\n");
+}
+
+static void mdfld_wait_for_HS_CTRL_FIFO(struct drm_device *dev, u32 pipe)
+{
+	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) && (REG_READ(gen_fifo_stat_reg)
+					& DSI_FIFO_GEN_HS_CTRL_FULL)) {
+		udelay(100);
+		timeout++;
+	}
+	if (timeout == 20000)
+		DRM_INFO("MIPI: HS CMD FIFO was never cleared!\n");
+}
+
+static void mdfld_wait_for_DPI_CTRL_FIFO(struct drm_device *dev, u32 pipe)
+{
+	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) && ((REG_READ(gen_fifo_stat_reg) &
+					DPI_FIFO_EMPTY) != DPI_FIFO_EMPTY)) {
+		udelay(100);
+		timeout++;
+	}
+
+	if (timeout == 20000)
+		DRM_ERROR("MIPI: DPI FIFO was never cleared\n");
+}
+
+static void mdfld_wait_for_SPL_PKG_SENT(struct drm_device *dev, u32 pipe)
+{
+	u32 intr_stat_reg = MIPI_INTR_STAT_REG(pipe);
+	int timeout = 0;
+
+	udelay(500);
+
+	/* This will time out after approximately 2+ seconds */
+	while ((timeout < 20000) && (!(REG_READ(intr_stat_reg)
+					& DSI_INTR_STATE_SPL_PKG_SENT))) {
+		udelay(100);
+		timeout++;
+	}
+
+	if (timeout == 20000)
+                DRM_ERROR("MIPI: SPL_PKT_SENT_INTERRUPT was not sent successfully!\n");
+}
+
+/* For TC35876X */
+
+static void dsi_set_device_ready_state(struct drm_device *dev, int state,
+				int pipe)
+{
+	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), !!state, 0, 0);
+}
+
+static void dsi_set_pipe_plane_enable_state(struct drm_device *dev,
+							int state, int pipe)
+{
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	u32 pipeconf_reg = PIPEACONF;
+	u32 dspcntr_reg = DSPACNTR;
+
+	u32 dspcntr = dev_priv->dspcntr[pipe];
+	u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX;
+
+	if (pipe) {
+		pipeconf_reg = PIPECCONF;
+		dspcntr_reg = DSPCCNTR;
+	} else
+		mipi &= (~0x03);
+
+	if (state) {
+		/*Set up pipe */
+		REG_WRITE(pipeconf_reg, BIT(31));
+
+		if (REG_BIT_WAIT(pipeconf_reg, 1, 30))
+			dev_err(&dev->pdev->dev, "%s: Pipe enable timeout\n",
+				__func__);
+
+		/*Set up display plane */
+		REG_WRITE(dspcntr_reg, dspcntr);
+	} else {
+		u32 dspbase_reg = pipe ? MDFLD_DSPCBASE : MRST_DSPABASE;
+
+		/* Put DSI lanes to ULPS to disable pipe */
+		REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 2, 2, 1);
+		REG_READ(MIPI_DEVICE_READY_REG(pipe)); /* posted write? */
+
+		/* LP Hold */
+		REG_FLD_MOD(MIPI_PORT_CONTROL(pipe), 0, 16, 16);
+		REG_READ(MIPI_PORT_CONTROL(pipe)); /* posted write? */
+
+		/* Disable display plane */
+		REG_FLD_MOD(dspcntr_reg, 0, 31, 31);
+
+		/* Flush the plane changes ??? posted write? */
+		REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+		REG_READ(dspbase_reg);
+
+		/* Disable PIPE */
+		REG_FLD_MOD(pipeconf_reg, 0, 31, 31);
+
+		if (REG_BIT_WAIT(pipeconf_reg, 0, 30))
+			dev_err(&dev->pdev->dev, "%s: Pipe disable timeout\n",
+				__func__);
+
+		if (REG_BIT_WAIT(MIPI_GEN_FIFO_STAT_REG(pipe), 1, 28))
+			dev_err(&dev->pdev->dev, "%s: FIFO not empty\n",
+				__func__);
+	}
+}
+
+static void mdfld_dsi_configure_down(struct mdfld_dsi_encoder *dsi_encoder,
+								int pipe)
+{
+	struct mdfld_dsi_dpi_output *dpi_output =
+				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	if (!dev_priv->dpi_panel_on[pipe]) {
+		dev_err(dev->dev, "DPI panel is already off\n");
+		return;
+	}
+	tc35876x_toshiba_bridge_panel_off(dev);
+	tc35876x_set_bridge_reset_state(dev, 1);
+	dsi_set_pipe_plane_enable_state(dev, 0, pipe);
+	mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+	dsi_set_device_ready_state(dev, 0, pipe);
+}
+
+static void mdfld_dsi_configure_up(struct mdfld_dsi_encoder *dsi_encoder,
+								int pipe)
+{
+	struct mdfld_dsi_dpi_output *dpi_output =
+				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	if (dev_priv->dpi_panel_on[pipe]) {
+		dev_err(dev->dev, "DPI panel is already on\n");
+		return;
+	}
+
+	/* For resume path sequence */
+	mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+	dsi_set_device_ready_state(dev, 0, pipe);
+
+	dsi_set_device_ready_state(dev, 1, pipe);
+	tc35876x_set_bridge_reset_state(dev, 0);
+	tc35876x_configure_lvds_bridge(dev);
+	mdfld_dsi_dpi_turn_on(dpi_output, pipe);  /* Send turn on command */
+	dsi_set_pipe_plane_enable_state(dev, 1, pipe);
+}
+/* End for TC35876X */
+
+/* ************************************************************************* *\
+ * FUNCTION: mdfld_dsi_tpo_ic_init
+ *
+ * DESCRIPTION:  This function is called only by mrst_dsi_mode_set and
+ *               restore_display_registers.  since this function does not
+ *               acquire the mutex, it is important that the calling function
+ *               does!
+\* ************************************************************************* */
+static void mdfld_dsi_tpo_ic_init(struct mdfld_dsi_config *dsi_config, u32 pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	u32 dcsChannelNumber = dsi_config->channel_num;
+	u32 gen_data_reg = MIPI_HS_GEN_DATA_REG(pipe);
+	u32 gen_ctrl_reg = MIPI_HS_GEN_CTRL_REG(pipe);
+	u32 gen_ctrl_val = GEN_LONG_WRITE;
+
+	DRM_INFO("Enter mrst init TPO MIPI display.\n");
+
+	gen_ctrl_val |= dcsChannelNumber << DCS_CHANNEL_NUMBER_POS;
+
+	/* Flip page order */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00008036);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS));
+
+	/* 0xF0 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x005a5af0);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* Write protection key */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x005a5af1);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* 0xFC */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x005a5afc);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* 0xB7 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x770000b7);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000044);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x05 << WORD_COUNTS_POS));
+
+	/* 0xB6 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000a0ab6);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+
+	/* 0xF2 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x081010f2);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x4a070708);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000000c5);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
+
+	/* 0xF8 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x024003f8);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x01030a04);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x0e020220);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000004);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x0d << WORD_COUNTS_POS));
+
+	/* 0xE2 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x398fc3e2);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x0000916f);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x06 << WORD_COUNTS_POS));
+
+	/* 0xB0 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000000b0);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS));
+
+	/* 0xF4 */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x240242f4);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x78ee2002);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2a071050);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x507fee10);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x10300710);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x14 << WORD_COUNTS_POS));
+
+	/* 0xBA */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x19fe07ba);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x101c0a31);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000010);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
+
+	/* 0xBB */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x28ff07bb);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x24280a31);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000034);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
+
+	/* 0xFB */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x535d05fb);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1b1a2130);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x221e180e);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x131d2120);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x535d0508);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1c1a2131);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x231f160d);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x111b2220);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x535c2008);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1f1d2433);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2c251a10);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2c34372d);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000023);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS));
+
+	/* 0xFA */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x525c0bfa);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1c1c232f);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x2623190e);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x18212625);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x545d0d0e);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1e1d2333);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x26231a10);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x1a222725);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x545d280f);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x21202635);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x31292013);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x31393d33);
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x00000029);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS));
+
+	/* Set DM */
+	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
+	REG_WRITE(gen_data_reg, 0x000100f7);
+	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
+	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
+}
+
+static u16 mdfld_dsi_dpi_to_byte_clock_count(int pixel_clock_count,
+						int num_lane, int bpp)
+{
+	return (u16)((pixel_clock_count * bpp) / (num_lane * 8));
+}
+
+/*
+ * Calculate the dpi time basing on a given drm mode @mode
+ * return 0 on success.
+ * FIXME: I was using proposed mode value for calculation, may need to
+ * use crtc mode values later
+ */
+int mdfld_dsi_dpi_timing_calculation(struct drm_display_mode *mode,
+				struct mdfld_dsi_dpi_timing *dpi_timing,
+				int num_lane, int bpp)
+{
+	int pclk_hsync, pclk_hfp, pclk_hbp, pclk_hactive;
+	int pclk_vsync, pclk_vfp, pclk_vbp, pclk_vactive;
+
+	pclk_hactive = mode->hdisplay;
+	pclk_hfp = mode->hsync_start - mode->hdisplay;
+	pclk_hsync = mode->hsync_end - mode->hsync_start;
+	pclk_hbp = mode->htotal - mode->hsync_end;
+
+	pclk_vactive = mode->vdisplay;
+	pclk_vfp = mode->vsync_start - mode->vdisplay;
+	pclk_vsync = mode->vsync_end - mode->vsync_start;
+	pclk_vbp = mode->vtotal - mode->vsync_end;
+
+	/*
+	 * byte clock counts were calculated by following formula
+	 * bclock_count = pclk_count * bpp / num_lane / 8
+	 */
+	dpi_timing->hsync_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hsync, num_lane, bpp);
+	dpi_timing->hbp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hbp, num_lane, bpp);
+	dpi_timing->hfp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hfp, num_lane, bpp);
+	dpi_timing->hactive_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_hactive, num_lane, bpp);
+	dpi_timing->vsync_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_vsync, num_lane, bpp);
+	dpi_timing->vbp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_vbp, num_lane, bpp);
+	dpi_timing->vfp_count = mdfld_dsi_dpi_to_byte_clock_count(
+						pclk_vfp, num_lane, bpp);
+
+	return 0;
+}
+
+void mdfld_dsi_dpi_controller_init(struct mdfld_dsi_config *dsi_config,
+								int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	int lane_count = dsi_config->lane_count;
+	struct mdfld_dsi_dpi_timing dpi_timing;
+	struct drm_display_mode *mode = dsi_config->mode;
+	u32 val;
+
+	/*un-ready device*/
+	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 0, 0, 0);
+
+	/*init dsi adapter before kicking off*/
+	REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018);
+
+	/*enable all interrupts*/
+	REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff);
+
+	/*set up func_prg*/
+	val = lane_count;
+	val |= dsi_config->channel_num << DSI_DPI_VIRT_CHANNEL_OFFSET;
+
+	switch (dsi_config->bpp) {
+	case 16:
+		val |= DSI_DPI_COLOR_FORMAT_RGB565;
+		break;
+	case 18:
+		val |= DSI_DPI_COLOR_FORMAT_RGB666;
+		break;
+	case 24:
+		val |= DSI_DPI_COLOR_FORMAT_RGB888;
+		break;
+	default:
+		DRM_ERROR("unsupported color format, bpp = %d\n",
+							dsi_config->bpp);
+	}
+	REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), val);
+
+	REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe),
+			(mode->vtotal * mode->htotal * dsi_config->bpp /
+				(8 * lane_count)) & DSI_HS_TX_TIMEOUT_MASK);
+	REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe),
+				0xffff & DSI_LP_RX_TIMEOUT_MASK);
+
+	/*max value: 20 clock cycles of txclkesc*/
+	REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe),
+				0x14 & DSI_TURN_AROUND_TIMEOUT_MASK);
+
+	/*min 21 txclkesc, max: ffffh*/
+	REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe),
+				0xffff & DSI_RESET_TIMER_MASK);
+
+	REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe),
+				mode->vdisplay << 16 | mode->hdisplay);
+
+	/*set DPI timing registers*/
+	mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing,
+				dsi_config->lane_count, dsi_config->bpp);
+
+	REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe),
+			dpi_timing.hsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HBP_COUNT_REG(pipe),
+			dpi_timing.hbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HFP_COUNT_REG(pipe),
+			dpi_timing.hfp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe),
+			dpi_timing.hactive_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe),
+			dpi_timing.vsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VBP_COUNT_REG(pipe),
+			dpi_timing.vbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VFP_COUNT_REG(pipe),
+			dpi_timing.vfp_count & DSI_DPI_TIMING_MASK);
+
+	REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x46);
+
+	/*min: 7d0 max: 4e20*/
+	REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0x000007d0);
+
+	/*set up video mode*/
+	val = dsi_config->video_mode | DSI_DPI_COMPLETE_LAST_LINE;
+	REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), val);
+
+	REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000);
+
+	REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004);
+
+	/*TODO: figure out how to setup these registers*/
+	if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008);
+	else
+		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150c3408);
+
+	REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14);
+
+	if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+		tc35876x_set_bridge_reset_state(dev, 0);  /*Pull High Reset */
+
+	/*set device ready*/
+	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 1, 0, 0);
+}
+
+void mdfld_dsi_dpi_turn_on(struct mdfld_dsi_dpi_output *output, int pipe)
+{
+	struct drm_device *dev = output->dev;
+
+	/* clear special packet sent bit */
+	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
+		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
+					DSI_INTR_STATE_SPL_PKG_SENT);
+
+	/*send turn on package*/
+	REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_TURN_ON);
+
+	/*wait for SPL_PKG_SENT interrupt*/
+	mdfld_wait_for_SPL_PKG_SENT(dev, pipe);
+
+	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
+		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
+					DSI_INTR_STATE_SPL_PKG_SENT);
+
+	output->panel_on = 1;
+
+	/* FIXME the following is disabled to WA the X slow start issue
+	   for TMD panel
+	if (pipe == 2)
+		dev_priv->dpi_panel_on2 = true;
+	else if (pipe == 0)
+		dev_priv->dpi_panel_on = true; */
+}
+
+static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output,
+								int pipe)
+{
+	struct drm_device *dev = output->dev;
+
+	/*if output is on, or mode setting didn't happen, ignore this*/
+	if ((!output->panel_on) || output->first_boot) {
+		output->first_boot = 0;
+		return;
+	}
+
+	/* Wait for dpi fifo to empty */
+	mdfld_wait_for_DPI_CTRL_FIFO(dev, pipe);
+
+	/* Clear the special packet interrupt bit if set */
+	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
+		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
+					DSI_INTR_STATE_SPL_PKG_SENT);
+
+	if (REG_READ(MIPI_DPI_CONTROL_REG(pipe)) == DSI_DPI_CTRL_HS_SHUTDOWN)
+		goto shutdown_out;
+
+	REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_SHUTDOWN);
+
+shutdown_out:
+	output->panel_on = 0;
+	output->first_boot = 0;
+
+	/* FIXME the following is disabled to WA the X slow start issue
+	   for TMD panel
+	if (pipe == 2)
+		dev_priv->dpi_panel_on2 = false;
+	else if (pipe == 0)
+		dev_priv->dpi_panel_on = false;	 */
+}
+
+static void mdfld_dsi_dpi_set_power(struct drm_encoder *encoder, bool on)
+{
+	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
+	struct mdfld_dsi_dpi_output *dpi_output =
+				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	u32 pipeconf_reg = PIPEACONF;
+
+	if (pipe)
+		pipeconf_reg = PIPECCONF;
+
+	/*start up display island if it was shutdown*/
+	if (!gma_power_begin(dev, true))
+		return;
+
+	if (on) {
+		if (mdfld_get_panel_type(dev, pipe) == TMD_VID)
+			mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+		else if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+			mdfld_dsi_configure_up(dsi_encoder, pipe);
+		else {
+			/*enable mipi port*/
+			REG_WRITE(MIPI_PORT_CONTROL(pipe),
+				REG_READ(MIPI_PORT_CONTROL(pipe)) | BIT(31));
+			REG_READ(MIPI_PORT_CONTROL(pipe));
+
+			mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+			mdfld_dsi_tpo_ic_init(dsi_config, pipe);
+		}
+		dev_priv->dpi_panel_on[pipe] = true;
+	} else {
+		if (mdfld_get_panel_type(dev, pipe) == TMD_VID)
+			mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+		else if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+			mdfld_dsi_configure_down(dsi_encoder, pipe);
+		else {
+			mdfld_dsi_dpi_shut_down(dpi_output, pipe);
+
+			/*disable mipi port*/
+			REG_WRITE(MIPI_PORT_CONTROL(pipe),
+				REG_READ(MIPI_PORT_CONTROL(pipe)) & ~BIT(31));
+			REG_READ(MIPI_PORT_CONTROL(pipe));
+		}
+		dev_priv->dpi_panel_on[pipe] = false;
+	}
+	gma_power_end(dev);
+}
+
+void mdfld_dsi_dpi_dpms(struct drm_encoder *encoder, int mode)
+{
+	mdfld_dsi_dpi_set_power(encoder, mode == DRM_MODE_DPMS_ON);
+}
+
+bool mdfld_dsi_dpi_mode_fixup(struct drm_encoder *encoder,
+				     struct drm_display_mode *mode,
+				     struct drm_display_mode *adjusted_mode)
+{
+	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_display_mode *fixed_mode = dsi_config->fixed_mode;
+
+	if (fixed_mode) {
+		adjusted_mode->hdisplay = fixed_mode->hdisplay;
+		adjusted_mode->hsync_start = fixed_mode->hsync_start;
+		adjusted_mode->hsync_end = fixed_mode->hsync_end;
+		adjusted_mode->htotal = fixed_mode->htotal;
+		adjusted_mode->vdisplay = fixed_mode->vdisplay;
+		adjusted_mode->vsync_start = fixed_mode->vsync_start;
+		adjusted_mode->vsync_end = fixed_mode->vsync_end;
+		adjusted_mode->vtotal = fixed_mode->vtotal;
+		adjusted_mode->clock = fixed_mode->clock;
+		drm_mode_set_crtcinfo(adjusted_mode, CRTC_INTERLACE_HALVE_V);
+	}
+	return true;
+}
+
+void mdfld_dsi_dpi_prepare(struct drm_encoder *encoder)
+{
+	mdfld_dsi_dpi_set_power(encoder, false);
+}
+
+void mdfld_dsi_dpi_commit(struct drm_encoder *encoder)
+{
+	mdfld_dsi_dpi_set_power(encoder, true);
+}
+
+/* For TC35876X */
+/* This functionality was implemented in FW in iCDK */
+/* But removed in DV0 and later. So need to add here. */
+static void mipi_set_properties(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+
+	REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018);
+	REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff);
+	REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe), 0xffffff);
+	REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe), 0xffffff);
+	REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe), 0x14);
+	REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe), 0xff);
+	REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x25);
+	REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0xf0);
+	REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000);
+	REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004);
+	REG_WRITE(MIPI_DBI_BW_CTRL_REG(pipe), 0x00000820);
+	REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14);
+}
+
+static void mdfld_mipi_set_video_timing(struct mdfld_dsi_config *dsi_config,
+					int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	struct mdfld_dsi_dpi_timing dpi_timing;
+	struct drm_display_mode *mode = dsi_config->mode;
+
+	mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing,
+					dsi_config->lane_count,
+					dsi_config->bpp);
+
+	REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe),
+		mode->vdisplay << 16 | mode->hdisplay);
+	REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe),
+		dpi_timing.hsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HBP_COUNT_REG(pipe),
+		dpi_timing.hbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HFP_COUNT_REG(pipe),
+		dpi_timing.hfp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe),
+		dpi_timing.hactive_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe),
+		dpi_timing.vsync_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VBP_COUNT_REG(pipe),
+		dpi_timing.vbp_count & DSI_DPI_TIMING_MASK);
+	REG_WRITE(MIPI_VFP_COUNT_REG(pipe),
+		dpi_timing.vfp_count & DSI_DPI_TIMING_MASK);
+}
+
+static void mdfld_mipi_config(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	int lane_count = dsi_config->lane_count;
+
+	if (pipe) {
+		REG_WRITE(MIPI_PORT_CONTROL(0), 0x00000002);
+		REG_WRITE(MIPI_PORT_CONTROL(2), 0x80000000);
+	} else {
+		REG_WRITE(MIPI_PORT_CONTROL(0), 0x80010000);
+		REG_WRITE(MIPI_PORT_CONTROL(2), 0x00);
+	}
+
+	REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150A600F);
+	REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), 0x0000000F);
+
+	/* lane_count = 3 */
+	REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), 0x00000200 | lane_count);
+
+	mdfld_mipi_set_video_timing(dsi_config, pipe);
+}
+
+static void mdfld_set_pipe_timing(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_display_mode *mode = dsi_config->mode;
+
+	REG_WRITE(HTOTAL_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1));
+	REG_WRITE(HBLANK_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1));
+	REG_WRITE(HSYNC_A,
+		((mode->hsync_end - 1) << 16) | (mode->hsync_start - 1));
+
+	REG_WRITE(VTOTAL_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1));
+	REG_WRITE(VBLANK_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1));
+	REG_WRITE(VSYNC_A,
+		((mode->vsync_end - 1) << 16) | (mode->vsync_start - 1));
+
+	REG_WRITE(PIPEASRC,
+		((mode->hdisplay - 1) << 16) | (mode->vdisplay - 1));
+}
+/* End for TC35876X */
+
+void mdfld_dsi_dpi_mode_set(struct drm_encoder *encoder,
+				   struct drm_display_mode *mode,
+				   struct drm_display_mode *adjusted_mode)
+{
+	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
+	struct mdfld_dsi_dpi_output *dpi_output =
+					MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_encoder_get_config(dsi_encoder);
+	struct drm_device *dev = dsi_config->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder);
+
+	u32 pipeconf_reg = PIPEACONF;
+	u32 dspcntr_reg = DSPACNTR;
+
+	u32 pipeconf = dev_priv->pipeconf[pipe];
+	u32 dspcntr = dev_priv->dspcntr[pipe];
+	u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX;
+
+	if (pipe) {
+		pipeconf_reg = PIPECCONF;
+		dspcntr_reg = DSPCCNTR;
+	} else {
+		if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+			mipi &= (~0x03); /* Use all four lanes */
+		else
+			mipi |= 2;
+	}
+
+	/*start up display island if it was shutdown*/
+	if (!gma_power_begin(dev, true))
+		return;
+
+	if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
+		/*
+		 * The following logic is required to reset the bridge and
+		 * configure. This also starts the DSI clock at 200MHz.
+		 */
+		tc35876x_set_bridge_reset_state(dev, 0);  /*Pull High Reset */
+		tc35876x_toshiba_bridge_panel_on(dev);
+		udelay(100);
+		/* Now start the DSI clock */
+		REG_WRITE(MRST_DPLL_A, 0x00);
+		REG_WRITE(MRST_FPA0, 0xC1);
+		REG_WRITE(MRST_DPLL_A, 0x00800000);
+		udelay(500);
+		REG_WRITE(MRST_DPLL_A, 0x80800000);
+
+		if (REG_BIT_WAIT(pipeconf_reg, 1, 29))
+			dev_err(&dev->pdev->dev, "%s: DSI PLL lock timeout\n",
+				__func__);
+
+		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008);
+
+		mipi_set_properties(dsi_config, pipe);
+		mdfld_mipi_config(dsi_config, pipe);
+		mdfld_set_pipe_timing(dsi_config, pipe);
+
+		REG_WRITE(DSPABASE, 0x00);
+		REG_WRITE(DSPASTRIDE, (mode->hdisplay * 4));
+		REG_WRITE(DSPASIZE,
+			((mode->vdisplay - 1) << 16) | (mode->hdisplay - 1));
+
+		REG_WRITE(DSPACNTR, 0x98000000);
+		REG_WRITE(DSPASURF, 0x00);
+
+		REG_WRITE(VGACNTRL, 0x80000000);
+		REG_WRITE(DEVICE_READY_REG, 0x00000001);
+
+		REG_WRITE(MIPI_PORT_CONTROL(pipe), 0x80810000);
+	} else {
+		/*set up mipi port FIXME: do at init time */
+		REG_WRITE(MIPI_PORT_CONTROL(pipe), mipi);
+	}
+	REG_READ(MIPI_PORT_CONTROL(pipe));
+
+	if (mdfld_get_panel_type(dev, pipe) == TMD_VID) {
+		/* NOP */
+	} else if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
+		/* set up DSI controller DPI interface */
+		mdfld_dsi_dpi_controller_init(dsi_config, pipe);
+
+		/* Configure MIPI Bridge and Panel */
+		tc35876x_configure_lvds_bridge(dev);
+		dev_priv->dpi_panel_on[pipe] = true;
+	} else {
+		/*turn on DPI interface*/
+		mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+	}
+
+	/*set up pipe*/
+	REG_WRITE(pipeconf_reg, pipeconf);
+	REG_READ(pipeconf_reg);
+
+	/*set up display plane*/
+	REG_WRITE(dspcntr_reg, dspcntr);
+	REG_READ(dspcntr_reg);
+
+	msleep(20); /* FIXME: this should wait for vblank */
+
+	if (mdfld_get_panel_type(dev, pipe) == TMD_VID) {
+		/* NOP */
+	} else if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
+		mdfld_dsi_dpi_turn_on(dpi_output, pipe);
+	} else {
+		/* init driver ic */
+		mdfld_dsi_tpo_ic_init(dsi_config, pipe);
+		/*init backlight*/
+		mdfld_dsi_brightness_init(dsi_config, pipe);
+	}
+
+	gma_power_end(dev);
+}
+
+/*
+ * Init DSI DPI encoder.
+ * Allocate an mdfld_dsi_encoder and attach it to given @dsi_connector
+ * return pointer of newly allocated DPI encoder, NULL on error
+ */
+struct mdfld_dsi_encoder *mdfld_dsi_dpi_init(struct drm_device *dev,
+				struct mdfld_dsi_connector *dsi_connector,
+				const struct panel_funcs *p_funcs)
+{
+	struct mdfld_dsi_dpi_output *dpi_output = NULL;
+	struct mdfld_dsi_config *dsi_config;
+	struct drm_connector *connector = NULL;
+	struct drm_encoder *encoder = NULL;
+	struct drm_display_mode *fixed_mode = NULL;
+	int pipe;
+	u32 data;
+	int ret;
+
+	pipe = dsi_connector->pipe;
+
+	if (mdfld_get_panel_type(dev, pipe) != TC35876X) {
+		dsi_config = mdfld_dsi_get_config(dsi_connector);
+
+		/* panel hard-reset */
+		if (p_funcs->reset) {
+			ret = p_funcs->reset(pipe);
+			if (ret) {
+				DRM_ERROR("Panel %d hard-reset failed\n", pipe);
+				return NULL;
+			}
+		}
+
+		/* panel drvIC init */
+		if (p_funcs->drv_ic_init)
+			p_funcs->drv_ic_init(dsi_config, pipe);
+
+		/* panel power mode detect */
+		ret = mdfld_dsi_get_power_mode(dsi_config, &data, false);
+		if (ret) {
+			DRM_ERROR("Panel %d get power mode failed\n", pipe);
+			dsi_connector->status = connector_status_disconnected;
+		} else {
+			DRM_INFO("pipe %d power mode 0x%x\n", pipe, data);
+			dsi_connector->status = connector_status_connected;
+		}
+	}
+
+	dpi_output = kzalloc(sizeof(struct mdfld_dsi_dpi_output), GFP_KERNEL);
+	if (!dpi_output) {
+		DRM_ERROR("No memory\n");
+		return NULL;
+	}
+
+	if (dsi_connector->pipe)
+		dpi_output->panel_on = 0;
+	else
+		dpi_output->panel_on = 0;
+
+	dpi_output->dev = dev;
+	if (mdfld_get_panel_type(dev, pipe) != TC35876X)
+		dpi_output->p_funcs = p_funcs;
+	dpi_output->first_boot = 1;
+
+	/*get fixed mode*/
+	dsi_config = mdfld_dsi_get_config(dsi_connector);
+	fixed_mode = dsi_config->fixed_mode;
+
+	/*create drm encoder object*/
+	connector = &dsi_connector->base.base;
+	encoder = &dpi_output->base.base.base;
+	drm_encoder_init(dev,
+			encoder,
+			p_funcs->encoder_funcs,
+			DRM_MODE_ENCODER_LVDS);
+	drm_encoder_helper_add(encoder,
+				p_funcs->encoder_helper_funcs);
+
+	/*attach to given connector*/
+	drm_mode_connector_attach_encoder(connector, encoder);
+
+	/*set possible crtcs and clones*/
+	if (dsi_connector->pipe) {
+		encoder->possible_crtcs = (1 << 2);
+		encoder->possible_clones = (1 << 1);
+	} else {
+		encoder->possible_crtcs = (1 << 0);
+		encoder->possible_clones = (1 << 0);
+	}
+
+	dsi_connector->base.encoder = &dpi_output->base.base;
+
+	return &dpi_output->base;
+}
diff --git a/drivers/gpu/drm/gma500/mdfld_dsi_dpi.h b/drivers/gpu/drm/gma500/mdfld_dsi_dpi.h
new file mode 100644
index 00000000000..6f762478b95
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_dsi_dpi.h
@@ -0,0 +1,79 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * jim liu <jim.liu@intel.com>
+ * Jackie Li<yaodong.li@intel.com>
+ */
+
+#ifndef __MDFLD_DSI_DPI_H__
+#define __MDFLD_DSI_DPI_H__
+
+#include "mdfld_dsi_output.h"
+#include "mdfld_output.h"
+
+struct mdfld_dsi_dpi_timing {
+	u16 hsync_count;
+	u16 hbp_count;
+	u16 hfp_count;
+	u16 hactive_count;
+	u16 vsync_count;
+	u16 vbp_count;
+	u16 vfp_count;
+};
+
+struct mdfld_dsi_dpi_output {
+	struct mdfld_dsi_encoder base;
+	struct drm_device *dev;
+
+	int panel_on;
+	int first_boot;
+
+	const struct panel_funcs *p_funcs;
+};
+
+#define MDFLD_DSI_DPI_OUTPUT(dsi_encoder)\
+	container_of(dsi_encoder, struct mdfld_dsi_dpi_output, base)
+
+/* Export functions */
+extern int mdfld_dsi_dpi_timing_calculation(struct drm_display_mode *mode,
+				struct mdfld_dsi_dpi_timing *dpi_timing,
+				int num_lane, int bpp);
+extern struct mdfld_dsi_encoder *mdfld_dsi_dpi_init(struct drm_device *dev,
+				struct mdfld_dsi_connector *dsi_connector,
+				const struct panel_funcs *p_funcs);
+
+/* MDFLD DPI helper functions */
+extern void mdfld_dsi_dpi_dpms(struct drm_encoder *encoder, int mode);
+extern bool mdfld_dsi_dpi_mode_fixup(struct drm_encoder *encoder,
+				struct drm_display_mode *mode,
+				struct drm_display_mode *adjusted_mode);
+extern void mdfld_dsi_dpi_prepare(struct drm_encoder *encoder);
+extern void mdfld_dsi_dpi_commit(struct drm_encoder *encoder);
+extern void mdfld_dsi_dpi_mode_set(struct drm_encoder *encoder,
+				struct drm_display_mode *mode,
+				struct drm_display_mode *adjusted_mode);
+extern void mdfld_dsi_dpi_turn_on(struct mdfld_dsi_dpi_output *output,
+				int pipe);
+extern void mdfld_dsi_dpi_controller_init(struct mdfld_dsi_config *dsi_config,
+				int pipe);
+#endif /*__MDFLD_DSI_DPI_H__*/
diff --git a/drivers/gpu/drm/gma500/mdfld_dsi_output.c b/drivers/gpu/drm/gma500/mdfld_dsi_output.c
new file mode 100644
index 00000000000..9338c28f399
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_dsi_output.c
@@ -0,0 +1,635 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * jim liu <jim.liu@intel.com>
+ * Jackie Li<yaodong.li@intel.com>
+ */
+
+#include <linux/module.h>
+
+#include "mdfld_dsi_output.h"
+#include "mdfld_dsi_dpi.h"
+#include "mdfld_output.h"
+#include "mdfld_dsi_pkg_sender.h"
+#include "tc35876x-dsi-lvds.h"
+#include <linux/pm_runtime.h>
+#include <asm/intel_scu_ipc.h>
+
+/* get the LABC from command line. */
+static int LABC_control = 1;
+
+#ifdef MODULE
+module_param(LABC_control, int, 0644);
+#else
+
+static int __init parse_LABC_control(char *arg)
+{
+	/* LABC control can be passed in as a cmdline parameter */
+	/* to enable this feature add LABC=1 to cmdline */
+	/* to disable this feature add LABC=0 to cmdline */
+	if (!arg)
+		return -EINVAL;
+
+	if (!strcasecmp(arg, "0"))
+		LABC_control = 0;
+	else if (!strcasecmp(arg, "1"))
+		LABC_control = 1;
+
+	return 0;
+}
+early_param("LABC", parse_LABC_control);
+#endif
+
+/**
+ * Check and see if the generic control or data buffer is empty and ready.
+ */
+void mdfld_dsi_gen_fifo_ready(struct drm_device *dev, u32 gen_fifo_stat_reg,
+							u32 fifo_stat)
+{
+	u32 GEN_BF_time_out_count;
+
+	/* Check MIPI Adatper command registers */
+	for (GEN_BF_time_out_count = 0;
+			GEN_BF_time_out_count < GEN_FB_TIME_OUT;
+			GEN_BF_time_out_count++) {
+		if ((REG_READ(gen_fifo_stat_reg) & fifo_stat) == fifo_stat)
+			break;
+		udelay(100);
+	}
+
+	if (GEN_BF_time_out_count == GEN_FB_TIME_OUT)
+		DRM_ERROR("mdfld_dsi_gen_fifo_ready, Timeout. gen_fifo_stat_reg = 0x%x.\n",
+					gen_fifo_stat_reg);
+}
+
+/**
+ * Manage the DSI MIPI keyboard and display brightness.
+ * FIXME: this is exported to OSPM code. should work out an specific
+ * display interface to OSPM.
+ */
+
+void mdfld_dsi_brightness_init(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	struct mdfld_dsi_pkg_sender *sender =
+				mdfld_dsi_get_pkg_sender(dsi_config);
+	struct drm_device *dev = sender->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	u32 gen_ctrl_val;
+
+	if (!sender) {
+		DRM_ERROR("No sender found\n");
+		return;
+	}
+
+	/* Set default display backlight value to 85% (0xd8)*/
+	mdfld_dsi_send_mcs_short(sender, write_display_brightness, 0xd8, 1,
+				true);
+
+	/* Set minimum brightness setting of CABC function to 20% (0x33)*/
+	mdfld_dsi_send_mcs_short(sender, write_cabc_min_bright, 0x33, 1, true);
+
+	/* Enable backlight or/and LABC */
+	gen_ctrl_val = BRIGHT_CNTL_BLOCK_ON | DISPLAY_DIMMING_ON |
+								BACKLIGHT_ON;
+	if (LABC_control == 1)
+		gen_ctrl_val |= DISPLAY_DIMMING_ON | DISPLAY_BRIGHTNESS_AUTO
+								| GAMMA_AUTO;
+
+	if (LABC_control == 1)
+		gen_ctrl_val |= AMBIENT_LIGHT_SENSE_ON;
+
+	dev_priv->mipi_ctrl_display = gen_ctrl_val;
+
+	mdfld_dsi_send_mcs_short(sender, write_ctrl_display, (u8)gen_ctrl_val,
+				1, true);
+
+	mdfld_dsi_send_mcs_short(sender, write_ctrl_cabc, UI_IMAGE, 1, true);
+}
+
+void mdfld_dsi_brightness_control(struct drm_device *dev, int pipe, int level)
+{
+	struct mdfld_dsi_pkg_sender *sender;
+	struct drm_psb_private *dev_priv;
+	struct mdfld_dsi_config *dsi_config;
+	u32 gen_ctrl_val = 0;
+	int p_type = TMD_VID;
+
+	if (!dev || (pipe != 0 && pipe != 2)) {
+		DRM_ERROR("Invalid parameter\n");
+		return;
+	}
+
+	p_type = mdfld_get_panel_type(dev, 0);
+
+	dev_priv = dev->dev_private;
+
+	if (pipe)
+		dsi_config = dev_priv->dsi_configs[1];
+	else
+		dsi_config = dev_priv->dsi_configs[0];
+
+	sender = mdfld_dsi_get_pkg_sender(dsi_config);
+
+	if (!sender) {
+		DRM_ERROR("No sender found\n");
+		return;
+	}
+
+	gen_ctrl_val = (level * 0xff / MDFLD_DSI_BRIGHTNESS_MAX_LEVEL) & 0xff;
+
+	dev_dbg(sender->dev->dev, "pipe = %d, gen_ctrl_val = %d.\n",
+							pipe, gen_ctrl_val);
+
+	if (p_type == TMD_VID) {
+		/* Set display backlight value */
+		mdfld_dsi_send_mcs_short(sender, tmd_write_display_brightness,
+					(u8)gen_ctrl_val, 1, true);
+	} else {
+		/* Set display backlight value */
+		mdfld_dsi_send_mcs_short(sender, write_display_brightness,
+					(u8)gen_ctrl_val, 1, true);
+
+		/* Enable backlight control */
+		if (level == 0)
+			gen_ctrl_val = 0;
+		else
+			gen_ctrl_val = dev_priv->mipi_ctrl_display;
+
+		mdfld_dsi_send_mcs_short(sender, write_ctrl_display,
+					(u8)gen_ctrl_val, 1, true);
+	}
+}
+
+static int mdfld_dsi_get_panel_status(struct mdfld_dsi_config *dsi_config,
+				u8 dcs, u32 *data, bool hs)
+{
+	struct mdfld_dsi_pkg_sender *sender
+		= mdfld_dsi_get_pkg_sender(dsi_config);
+
+	if (!sender || !data) {
+		DRM_ERROR("Invalid parameter\n");
+		return -EINVAL;
+	}
+
+	return mdfld_dsi_read_mcs(sender, dcs, data, 1, hs);
+}
+
+int mdfld_dsi_get_power_mode(struct mdfld_dsi_config *dsi_config, u32 *mode,
+			bool hs)
+{
+	if (!dsi_config || !mode) {
+		DRM_ERROR("Invalid parameter\n");
+		return -EINVAL;
+	}
+
+	return mdfld_dsi_get_panel_status(dsi_config, 0x0a, mode, hs);
+}
+
+int mdfld_dsi_get_diagnostic_result(struct mdfld_dsi_config *dsi_config,
+				u32 *result, bool hs)
+{
+	if (!dsi_config || !result) {
+		DRM_ERROR("Invalid parameter\n");
+		return -EINVAL;
+	}
+
+	return mdfld_dsi_get_panel_status(dsi_config, 0x0f, result, hs);
+}
+
+/*
+ * NOTE: this function was used by OSPM.
+ * TODO: will be removed later, should work out display interfaces for OSPM
+ */
+void mdfld_dsi_controller_init(struct mdfld_dsi_config *dsi_config, int pipe)
+{
+	if (!dsi_config || ((pipe != 0) && (pipe != 2))) {
+		DRM_ERROR("Invalid parameters\n");
+		return;
+	}
+
+	mdfld_dsi_dpi_controller_init(dsi_config, pipe);
+}
+
+static void mdfld_dsi_connector_save(struct drm_connector *connector)
+{
+}
+
+static void mdfld_dsi_connector_restore(struct drm_connector *connector)
+{
+}
+
+/* FIXME: start using the force parameter */
+static enum drm_connector_status
+mdfld_dsi_connector_detect(struct drm_connector *connector, bool force)
+{
+	struct mdfld_dsi_connector *dsi_connector
+		= mdfld_dsi_connector(connector);
+
+	dsi_connector->status = connector_status_connected;
+
+	return dsi_connector->status;
+}
+
+static int mdfld_dsi_connector_set_property(struct drm_connector *connector,
+				struct drm_property *property,
+				uint64_t value)
+{
+	struct drm_encoder *encoder = connector->encoder;
+	struct backlight_device *psb_bd;
+
+	if (!strcmp(property->name, "scaling mode") && encoder) {
+		struct psb_intel_crtc *psb_crtc =
+					to_psb_intel_crtc(encoder->crtc);
+		bool centerechange;
+		uint64_t val;
+
+		if (!psb_crtc)
+			goto set_prop_error;
+
+		switch (value) {
+		case DRM_MODE_SCALE_FULLSCREEN:
+			break;
+		case DRM_MODE_SCALE_NO_SCALE:
+			break;
+		case DRM_MODE_SCALE_ASPECT:
+			break;
+		default:
+			goto set_prop_error;
+		}
+
+		if (drm_connector_property_get_value(connector, property, &val))
+			goto set_prop_error;
+
+		if (val == value)
+			goto set_prop_done;
+
+		if (drm_connector_property_set_value(connector,
+							property, value))
+			goto set_prop_error;
+
+		centerechange = (val == DRM_MODE_SCALE_NO_SCALE) ||
+			(value == DRM_MODE_SCALE_NO_SCALE);
+
+		if (psb_crtc->saved_mode.hdisplay != 0 &&
+		    psb_crtc->saved_mode.vdisplay != 0) {
+			if (centerechange) {
+				if (!drm_crtc_helper_set_mode(encoder->crtc,
+						&psb_crtc->saved_mode,
+						encoder->crtc->x,
+						encoder->crtc->y,
+						encoder->crtc->fb))
+					goto set_prop_error;
+			} else {
+				struct drm_encoder_helper_funcs *funcs =
+						encoder->helper_private;
+				funcs->mode_set(encoder,
+					&psb_crtc->saved_mode,
+					&psb_crtc->saved_adjusted_mode);
+			}
+		}
+	} else if (!strcmp(property->name, "backlight") && encoder) {
+		if (drm_connector_property_set_value(connector, property,
+									value))
+			goto set_prop_error;
+		else {
+			psb_bd = mdfld_get_backlight_device();
+			if (psb_bd) {
+				psb_bd->props.brightness = value;
+				mdfld_set_brightness(psb_bd);
+			}
+		}
+	}
+set_prop_done:
+	return 0;
+set_prop_error:
+	return -1;
+}
+
+static void mdfld_dsi_connector_destroy(struct drm_connector *connector)
+{
+	struct mdfld_dsi_connector *dsi_connector =
+					mdfld_dsi_connector(connector);
+	struct mdfld_dsi_pkg_sender *sender;
+
+	if (!dsi_connector)
+		return;
+	drm_sysfs_connector_remove(connector);
+	drm_connector_cleanup(connector);
+	sender = dsi_connector->pkg_sender;
+	mdfld_dsi_pkg_sender_destroy(sender);
+	kfree(dsi_connector);
+}
+
+static int mdfld_dsi_connector_get_modes(struct drm_connector *connector)
+{
+	struct mdfld_dsi_connector *dsi_connector =
+				mdfld_dsi_connector(connector);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_get_config(dsi_connector);
+	struct drm_display_mode *fixed_mode = dsi_config->fixed_mode;
+	struct drm_display_mode *dup_mode = NULL;
+	struct drm_device *dev = connector->dev;
+
+	connector->display_info.min_vfreq = 0;
+	connector->display_info.max_vfreq = 200;
+	connector->display_info.min_hfreq = 0;
+	connector->display_info.max_hfreq = 200;
+
+	if (fixed_mode) {
+		dev_dbg(dev->dev, "fixed_mode %dx%d\n",
+				fixed_mode->hdisplay, fixed_mode->vdisplay);
+		dup_mode = drm_mode_duplicate(dev, fixed_mode);
+		drm_mode_probed_add(connector, dup_mode);
+		return 1;
+	}
+	DRM_ERROR("Didn't get any modes!\n");
+	return 0;
+}
+
+static int mdfld_dsi_connector_mode_valid(struct drm_connector *connector,
+						struct drm_display_mode *mode)
+{
+	struct mdfld_dsi_connector *dsi_connector =
+					mdfld_dsi_connector(connector);
+	struct mdfld_dsi_config *dsi_config =
+					mdfld_dsi_get_config(dsi_connector);
+	struct drm_display_mode *fixed_mode = dsi_config->fixed_mode;
+
+	if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
+		return MODE_NO_DBLESCAN;
+
+	if (mode->flags & DRM_MODE_FLAG_INTERLACE)
+		return MODE_NO_INTERLACE;
+
+	/**
+	 * FIXME: current DC has no fitting unit, reject any mode setting
+	 * request
+	 * Will figure out a way to do up-scaling(pannel fitting) later.
+	 **/
+	if (fixed_mode) {
+		if (mode->hdisplay != fixed_mode->hdisplay)
+			return MODE_PANEL;
+
+		if (mode->vdisplay != fixed_mode->vdisplay)
+			return MODE_PANEL;
+	}
+
+	return MODE_OK;
+}
+
+static void mdfld_dsi_connector_dpms(struct drm_connector *connector, int mode)
+{
+	if (mode == connector->dpms)
+		return;
+
+	/*first, execute dpms*/
+
+	drm_helper_connector_dpms(connector, mode);
+}
+
+static struct drm_encoder *mdfld_dsi_connector_best_encoder(
+				struct drm_connector *connector)
+{
+	struct mdfld_dsi_connector *dsi_connector =
+				mdfld_dsi_connector(connector);
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_get_config(dsi_connector);
+	return &dsi_config->encoder->base.base;
+}
+
+/*DSI connector funcs*/
+static const struct drm_connector_funcs mdfld_dsi_connector_funcs = {
+	.dpms = /*drm_helper_connector_dpms*/mdfld_dsi_connector_dpms,
+	.save = mdfld_dsi_connector_save,
+	.restore = mdfld_dsi_connector_restore,
+	.detect = mdfld_dsi_connector_detect,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.set_property = mdfld_dsi_connector_set_property,
+	.destroy = mdfld_dsi_connector_destroy,
+};
+
+/*DSI connector helper funcs*/
+static const struct drm_connector_helper_funcs
+	mdfld_dsi_connector_helper_funcs = {
+	.get_modes = mdfld_dsi_connector_get_modes,
+	.mode_valid = mdfld_dsi_connector_mode_valid,
+	.best_encoder = mdfld_dsi_connector_best_encoder,
+};
+
+static int mdfld_dsi_get_default_config(struct drm_device *dev,
+				struct mdfld_dsi_config *config, int pipe)
+{
+	if (!dev || !config) {
+		DRM_ERROR("Invalid parameters");
+		return -EINVAL;
+	}
+
+	config->bpp = 24;
+	if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+		config->lane_count = 4;
+	else
+		config->lane_count = 2;
+	config->channel_num = 0;
+
+	if (mdfld_get_panel_type(dev, pipe) == TMD_VID)
+		config->video_mode = MDFLD_DSI_VIDEO_NON_BURST_MODE_SYNC_PULSE;
+	else if (mdfld_get_panel_type(dev, pipe) == TC35876X)
+		config->video_mode =
+				MDFLD_DSI_VIDEO_NON_BURST_MODE_SYNC_EVENTS;
+	else
+		config->video_mode = MDFLD_DSI_VIDEO_BURST_MODE;
+
+	return 0;
+}
+
+int mdfld_dsi_panel_reset(int pipe)
+{
+	unsigned gpio;
+	int ret = 0;
+
+	switch (pipe) {
+	case 0:
+		gpio = 128;
+		break;
+	case 2:
+		gpio = 34;
+		break;
+	default:
+		DRM_ERROR("Invalid output\n");
+		return -EINVAL;
+	}
+
+	ret = gpio_request(gpio, "gfx");
+	if (ret) {
+		DRM_ERROR("gpio_rqueset failed\n");
+		return ret;
+	}
+
+	ret = gpio_direction_output(gpio, 1);
+	if (ret) {
+		DRM_ERROR("gpio_direction_output failed\n");
+		goto gpio_error;
+	}
+
+	gpio_get_value(128);
+
+gpio_error:
+	if (gpio_is_valid(gpio))
+		gpio_free(gpio);
+
+	return ret;
+}
+
+/*
+ * MIPI output init
+ * @dev drm device
+ * @pipe pipe number. 0 or 2
+ * @config
+ *
+ * Do the initialization of a MIPI output, including create DRM mode objects
+ * initialization of DSI output on @pipe
+ */
+void mdfld_dsi_output_init(struct drm_device *dev,
+			   int pipe,
+			   struct mdfld_dsi_config *config,
+			   const struct panel_funcs *p_vid_funcs)
+{
+	struct mdfld_dsi_config *dsi_config;
+	struct mdfld_dsi_connector *dsi_connector;
+	struct drm_connector *connector;
+	struct mdfld_dsi_encoder *encoder;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	struct panel_info dsi_panel_info;
+	u32 width_mm, height_mm;
+
+	dev_dbg(dev->dev, "init DSI output on pipe %d\n", pipe);
+
+	if (!dev || ((pipe != 0) && (pipe != 2))) {
+		DRM_ERROR("Invalid parameter\n");
+		return;
+	}
+
+	/*create a new connetor*/
+	dsi_connector = kzalloc(sizeof(struct mdfld_dsi_connector), GFP_KERNEL);
+	if (!dsi_connector) {
+		DRM_ERROR("No memory");
+		return;
+	}
+
+	dsi_connector->pipe =  pipe;
+
+	/*set DSI config*/
+	if (config)
+		dsi_config = config;
+	else {
+		dsi_config = kzalloc(sizeof(struct mdfld_dsi_config),
+								GFP_KERNEL);
+		if (!dsi_config) {
+			DRM_ERROR("cannot allocate memory for DSI config\n");
+			goto dsi_init_err0;
+		}
+		mdfld_dsi_get_default_config(dev, dsi_config, pipe);
+	}
+
+	dsi_connector->private = dsi_config;
+
+	dsi_config->changed = 1;
+	dsi_config->dev = dev;
+
+	dsi_config->fixed_mode = p_vid_funcs->get_config_mode(dev);
+	if (p_vid_funcs->get_panel_info(dev, pipe, &dsi_panel_info))
+			goto dsi_init_err0;
+
+	width_mm = dsi_panel_info.width_mm;
+	height_mm = dsi_panel_info.height_mm;
+
+	dsi_config->mode = dsi_config->fixed_mode;
+	dsi_config->connector = dsi_connector;
+
+	if (!dsi_config->fixed_mode) {
+		DRM_ERROR("No pannel fixed mode was found\n");
+		goto dsi_init_err0;
+	}
+
+	if (pipe && dev_priv->dsi_configs[0]) {
+		dsi_config->dvr_ic_inited = 0;
+		dev_priv->dsi_configs[1] = dsi_config;
+	} else if (pipe == 0) {
+		dsi_config->dvr_ic_inited = 1;
+		dev_priv->dsi_configs[0] = dsi_config;
+	} else {
+		DRM_ERROR("Trying to init MIPI1 before MIPI0\n");
+		goto dsi_init_err0;
+	}
+
+
+	connector = &dsi_connector->base.base;
+	drm_connector_init(dev, connector, &mdfld_dsi_connector_funcs,
+						DRM_MODE_CONNECTOR_LVDS);
+	drm_connector_helper_add(connector, &mdfld_dsi_connector_helper_funcs);
+
+	connector->display_info.subpixel_order = SubPixelHorizontalRGB;
+	connector->display_info.width_mm = width_mm;
+	connector->display_info.height_mm = height_mm;
+	connector->interlace_allowed = false;
+	connector->doublescan_allowed = false;
+
+	/*attach properties*/
+	drm_connector_attach_property(connector,
+				dev->mode_config.scaling_mode_property,
+				DRM_MODE_SCALE_FULLSCREEN);
+	drm_connector_attach_property(connector,
+				dev_priv->backlight_property,
+				MDFLD_DSI_BRIGHTNESS_MAX_LEVEL);
+
+	/*init DSI package sender on this output*/
+	if (mdfld_dsi_pkg_sender_init(dsi_connector, pipe)) {
+		DRM_ERROR("Package Sender initialization failed on pipe %d\n",
+									pipe);
+		goto dsi_init_err0;
+	}
+
+	encoder = mdfld_dsi_dpi_init(dev, dsi_connector, p_vid_funcs);
+	if (!encoder) {
+		DRM_ERROR("Create DPI encoder failed\n");
+		goto dsi_init_err1;
+	}
+	encoder->private = dsi_config;
+	dsi_config->encoder = encoder;
+	encoder->base.type = (pipe == 0) ? INTEL_OUTPUT_MIPI :
+		INTEL_OUTPUT_MIPI2;
+	drm_sysfs_connector_add(connector);
+	return;
+
+	/*TODO: add code to destroy outputs on error*/
+dsi_init_err1:
+	/*destroy sender*/
+	mdfld_dsi_pkg_sender_destroy(dsi_connector->pkg_sender);
+
+	drm_connector_cleanup(connector);
+
+	kfree(dsi_config->fixed_mode);
+	kfree(dsi_config);
+dsi_init_err0:
+	kfree(dsi_connector);
+}
diff --git a/drivers/gpu/drm/gma500/mdfld_dsi_output.h b/drivers/gpu/drm/gma500/mdfld_dsi_output.h
new file mode 100644
index 00000000000..2cdf666536d
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_dsi_output.h
@@ -0,0 +1,389 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * jim liu <jim.liu@intel.com>
+ * Jackie Li<yaodong.li@intel.com>
+ */
+
+#ifndef __MDFLD_DSI_OUTPUT_H__
+#define __MDFLD_DSI_OUTPUT_H__
+
+#include <linux/backlight.h>
+#include <linux/version.h>
+#include <drm/drmP.h>
+#include <drm/drm.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_edid.h>
+
+#include "psb_drv.h"
+#include "psb_intel_drv.h"
+#include "psb_intel_reg.h"
+#include "mdfld_output.h"
+
+#include <asm/mrst.h>
+
+#define FLD_MASK(start, end)	(((1 << ((start) - (end) + 1)) - 1) << (end))
+#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end))
+#define FLD_GET(val, start, end) (((val) & FLD_MASK(start, end)) >> (end))
+#define FLD_MOD(orig, val, start, end) \
+	(((orig) & ~FLD_MASK(start, end)) | FLD_VAL(val, start, end))
+
+#define REG_FLD_MOD(reg, val, start, end) \
+	REG_WRITE(reg, FLD_MOD(REG_READ(reg), val, start, end))
+
+static inline int REGISTER_FLD_WAIT(struct drm_device *dev, u32 reg,
+		u32 val, int start, int end)
+{
+	int t = 100000;
+
+	while (FLD_GET(REG_READ(reg), start, end) != val) {
+		if (--t == 0)
+			return 1;
+	}
+
+	return 0;
+}
+
+#define REG_FLD_WAIT(reg, val, start, end) \
+	REGISTER_FLD_WAIT(dev, reg, val, start, end)
+
+#define REG_BIT_WAIT(reg, val, bitnum) \
+	REGISTER_FLD_WAIT(dev, reg, val, bitnum, bitnum)
+
+#define MDFLD_DSI_BRIGHTNESS_MAX_LEVEL 100
+
+#ifdef DEBUG
+#define CHECK_PIPE(pipe) ({			\
+	const typeof(pipe) __pipe = (pipe);	\
+	BUG_ON(__pipe != 0 && __pipe != 2);	\
+	__pipe;	})
+#else
+#define CHECK_PIPE(pipe) (pipe)
+#endif
+
+/*
+ * Actual MIPIA->MIPIC reg offset is 0x800, value 0x400 is valid for 0 and 2
+ */
+#define REG_OFFSET(pipe) (CHECK_PIPE(pipe) * 0x400)
+
+/* mdfld DSI controller registers */
+#define MIPI_DEVICE_READY_REG(pipe)		(0xb000 + REG_OFFSET(pipe))
+#define MIPI_INTR_STAT_REG(pipe)		(0xb004 + REG_OFFSET(pipe))
+#define MIPI_INTR_EN_REG(pipe)			(0xb008 + REG_OFFSET(pipe))
+#define MIPI_DSI_FUNC_PRG_REG(pipe)		(0xb00c + REG_OFFSET(pipe))
+#define MIPI_HS_TX_TIMEOUT_REG(pipe)		(0xb010 + REG_OFFSET(pipe))
+#define MIPI_LP_RX_TIMEOUT_REG(pipe)		(0xb014 + REG_OFFSET(pipe))
+#define MIPI_TURN_AROUND_TIMEOUT_REG(pipe)	(0xb018 + REG_OFFSET(pipe))
+#define MIPI_DEVICE_RESET_TIMER_REG(pipe)	(0xb01c + REG_OFFSET(pipe))
+#define MIPI_DPI_RESOLUTION_REG(pipe)		(0xb020 + REG_OFFSET(pipe))
+#define MIPI_DBI_FIFO_THROTTLE_REG(pipe)	(0xb024 + REG_OFFSET(pipe))
+#define MIPI_HSYNC_COUNT_REG(pipe)		(0xb028 + REG_OFFSET(pipe))
+#define MIPI_HBP_COUNT_REG(pipe)		(0xb02c + REG_OFFSET(pipe))
+#define MIPI_HFP_COUNT_REG(pipe)		(0xb030 + REG_OFFSET(pipe))
+#define MIPI_HACTIVE_COUNT_REG(pipe)		(0xb034 + REG_OFFSET(pipe))
+#define MIPI_VSYNC_COUNT_REG(pipe)		(0xb038 + REG_OFFSET(pipe))
+#define MIPI_VBP_COUNT_REG(pipe)		(0xb03c + REG_OFFSET(pipe))
+#define MIPI_VFP_COUNT_REG(pipe)		(0xb040 + REG_OFFSET(pipe))
+#define MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe)	(0xb044 + REG_OFFSET(pipe))
+#define MIPI_DPI_CONTROL_REG(pipe)		(0xb048 + REG_OFFSET(pipe))
+#define MIPI_DPI_DATA_REG(pipe)			(0xb04c + REG_OFFSET(pipe))
+#define MIPI_INIT_COUNT_REG(pipe)		(0xb050 + REG_OFFSET(pipe))
+#define MIPI_MAX_RETURN_PACK_SIZE_REG(pipe)	(0xb054 + REG_OFFSET(pipe))
+#define MIPI_VIDEO_MODE_FORMAT_REG(pipe)	(0xb058 + REG_OFFSET(pipe))
+#define MIPI_EOT_DISABLE_REG(pipe)		(0xb05c + REG_OFFSET(pipe))
+#define MIPI_LP_BYTECLK_REG(pipe)		(0xb060 + REG_OFFSET(pipe))
+#define MIPI_LP_GEN_DATA_REG(pipe)		(0xb064 + REG_OFFSET(pipe))
+#define MIPI_HS_GEN_DATA_REG(pipe)		(0xb068 + REG_OFFSET(pipe))
+#define MIPI_LP_GEN_CTRL_REG(pipe)		(0xb06c + REG_OFFSET(pipe))
+#define MIPI_HS_GEN_CTRL_REG(pipe)		(0xb070 + REG_OFFSET(pipe))
+#define MIPI_GEN_FIFO_STAT_REG(pipe)		(0xb074 + REG_OFFSET(pipe))
+#define MIPI_HS_LS_DBI_ENABLE_REG(pipe)		(0xb078 + REG_OFFSET(pipe))
+#define MIPI_DPHY_PARAM_REG(pipe)		(0xb080 + REG_OFFSET(pipe))
+#define MIPI_DBI_BW_CTRL_REG(pipe)		(0xb084 + REG_OFFSET(pipe))
+#define MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe)	(0xb088 + REG_OFFSET(pipe))
+
+#define MIPI_CTRL_REG(pipe)			(0xb104 + REG_OFFSET(pipe))
+#define MIPI_DATA_ADD_REG(pipe)			(0xb108 + REG_OFFSET(pipe))
+#define MIPI_DATA_LEN_REG(pipe)			(0xb10c + REG_OFFSET(pipe))
+#define MIPI_CMD_ADD_REG(pipe)			(0xb110 + REG_OFFSET(pipe))
+#define MIPI_CMD_LEN_REG(pipe)			(0xb114 + REG_OFFSET(pipe))
+
+/* non-uniform reg offset */
+#define MIPI_PORT_CONTROL(pipe)		(CHECK_PIPE(pipe) ? MIPI_C : MIPI)
+
+#define DSI_DEVICE_READY				(0x1)
+#define DSI_POWER_STATE_ULPS_ENTER			(0x2 << 1)
+#define DSI_POWER_STATE_ULPS_EXIT			(0x1 << 1)
+#define DSI_POWER_STATE_ULPS_OFFSET			(0x1)
+
+
+#define DSI_ONE_DATA_LANE					(0x1)
+#define DSI_TWO_DATA_LANE					(0x2)
+#define DSI_THREE_DATA_LANE					(0X3)
+#define DSI_FOUR_DATA_LANE					(0x4)
+#define DSI_DPI_VIRT_CHANNEL_OFFSET			(0x3)
+#define DSI_DBI_VIRT_CHANNEL_OFFSET			(0x5)
+#define DSI_DPI_COLOR_FORMAT_RGB565			(0x01 << 7)
+#define DSI_DPI_COLOR_FORMAT_RGB666			(0x02 << 7)
+#define DSI_DPI_COLOR_FORMAT_RGB666_UNPACK		(0x03 << 7)
+#define DSI_DPI_COLOR_FORMAT_RGB888			(0x04 << 7)
+#define DSI_DBI_COLOR_FORMAT_OPTION2			(0x05 << 13)
+
+#define DSI_INTR_STATE_RXSOTERROR			BIT(0)
+
+#define DSI_INTR_STATE_SPL_PKG_SENT			BIT(30)
+#define DSI_INTR_STATE_TE				BIT(31)
+
+#define DSI_HS_TX_TIMEOUT_MASK				(0xffffff)
+
+#define DSI_LP_RX_TIMEOUT_MASK				(0xffffff)
+
+#define DSI_TURN_AROUND_TIMEOUT_MASK		(0x3f)
+
+#define DSI_RESET_TIMER_MASK				(0xffff)
+
+#define DSI_DBI_FIFO_WM_HALF				(0x0)
+#define DSI_DBI_FIFO_WM_QUARTER				(0x1)
+#define DSI_DBI_FIFO_WM_LOW					(0x2)
+
+#define DSI_DPI_TIMING_MASK					(0xffff)
+
+#define DSI_INIT_TIMER_MASK					(0xffff)
+
+#define DSI_DBI_RETURN_PACK_SIZE_MASK		(0x3ff)
+
+#define DSI_LP_BYTECLK_MASK					(0x0ffff)
+
+#define DSI_HS_CTRL_GEN_SHORT_W0			(0x03)
+#define DSI_HS_CTRL_GEN_SHORT_W1			(0x13)
+#define DSI_HS_CTRL_GEN_SHORT_W2			(0x23)
+#define DSI_HS_CTRL_GEN_R0					(0x04)
+#define DSI_HS_CTRL_GEN_R1					(0x14)
+#define DSI_HS_CTRL_GEN_R2					(0x24)
+#define DSI_HS_CTRL_GEN_LONG_W				(0x29)
+#define DSI_HS_CTRL_MCS_SHORT_W0			(0x05)
+#define DSI_HS_CTRL_MCS_SHORT_W1			(0x15)
+#define DSI_HS_CTRL_MCS_R0					(0x06)
+#define DSI_HS_CTRL_MCS_LONG_W				(0x39)
+#define DSI_HS_CTRL_VC_OFFSET				(0x06)
+#define DSI_HS_CTRL_WC_OFFSET				(0x08)
+
+#define	DSI_FIFO_GEN_HS_DATA_FULL			BIT(0)
+#define DSI_FIFO_GEN_HS_DATA_HALF_EMPTY		BIT(1)
+#define DSI_FIFO_GEN_HS_DATA_EMPTY			BIT(2)
+#define DSI_FIFO_GEN_LP_DATA_FULL			BIT(8)
+#define DSI_FIFO_GEN_LP_DATA_HALF_EMPTY		BIT(9)
+#define DSI_FIFO_GEN_LP_DATA_EMPTY			BIT(10)
+#define DSI_FIFO_GEN_HS_CTRL_FULL			BIT(16)
+#define DSI_FIFO_GEN_HS_CTRL_HALF_EMPTY		BIT(17)
+#define DSI_FIFO_GEN_HS_CTRL_EMPTY			BIT(18)
+#define DSI_FIFO_GEN_LP_CTRL_FULL			BIT(24)
+#define DSI_FIFO_GEN_LP_CTRL_HALF_EMPTY		BIT(25)
+#define DSI_FIFO_GEN_LP_CTRL_EMPTY			BIT(26)
+#define DSI_FIFO_DBI_EMPTY					BIT(27)
+#define DSI_FIFO_DPI_EMPTY					BIT(28)
+
+#define DSI_DBI_HS_LP_SWITCH_MASK			(0x1)
+
+#define DSI_HS_LP_SWITCH_COUNTER_OFFSET		(0x0)
+#define DSI_LP_HS_SWITCH_COUNTER_OFFSET		(0x16)
+
+#define DSI_DPI_CTRL_HS_SHUTDOWN			(0x00000001)
+#define DSI_DPI_CTRL_HS_TURN_ON				(0x00000002)
+
+/*dsi power modes*/
+#define DSI_POWER_MODE_DISPLAY_ON	BIT(2)
+#define DSI_POWER_MODE_NORMAL_ON	BIT(3)
+#define DSI_POWER_MODE_SLEEP_OUT	BIT(4)
+#define DSI_POWER_MODE_PARTIAL_ON	BIT(5)
+#define DSI_POWER_MODE_IDLE_ON		BIT(6)
+
+enum {
+	MDFLD_DSI_VIDEO_NON_BURST_MODE_SYNC_PULSE = 1,
+	MDFLD_DSI_VIDEO_NON_BURST_MODE_SYNC_EVENTS = 2,
+	MDFLD_DSI_VIDEO_BURST_MODE = 3,
+};
+
+#define DSI_DPI_COMPLETE_LAST_LINE			BIT(2)
+#define DSI_DPI_DISABLE_BTA					BIT(3)
+
+struct mdfld_dsi_connector_state {
+	u32 mipi_ctrl_reg;
+};
+
+struct mdfld_dsi_encoder_state {
+
+};
+
+struct mdfld_dsi_connector {
+	struct psb_intel_connector base;
+
+	int pipe;
+	void *private;
+	void *pkg_sender;
+
+	/* Connection status */
+	enum drm_connector_status status;
+};
+
+struct mdfld_dsi_encoder {
+	struct psb_intel_encoder base;
+	void *private;
+};
+
+/*
+ * DSI config, consists of one DSI connector, two DSI encoders.
+ * DRM will pick up on DSI encoder basing on differents configs.
+ */
+struct mdfld_dsi_config {
+	struct drm_device *dev;
+	struct drm_display_mode *fixed_mode;
+	struct drm_display_mode *mode;
+
+	struct mdfld_dsi_connector *connector;
+	struct mdfld_dsi_encoder *encoder;
+
+	int changed;
+
+	int bpp;
+	int lane_count;
+	/*Virtual channel number for this encoder*/
+	int channel_num;
+	/*video mode configure*/
+	int video_mode;
+
+	int dvr_ic_inited;
+};
+
+static inline struct mdfld_dsi_connector *mdfld_dsi_connector(
+		struct drm_connector *connector)
+{
+	struct psb_intel_connector *psb_connector;
+
+	psb_connector = to_psb_intel_connector(connector);
+
+	return container_of(psb_connector, struct mdfld_dsi_connector, base);
+}
+
+static inline struct mdfld_dsi_encoder *mdfld_dsi_encoder(
+		struct drm_encoder *encoder)
+{
+	struct psb_intel_encoder *psb_encoder;
+
+	psb_encoder = to_psb_intel_encoder(encoder);
+
+	return container_of(psb_encoder, struct mdfld_dsi_encoder, base);
+}
+
+static inline struct mdfld_dsi_config *
+	mdfld_dsi_get_config(struct mdfld_dsi_connector *connector)
+{
+	if (!connector)
+		return NULL;
+	return (struct mdfld_dsi_config *)connector->private;
+}
+
+static inline void *mdfld_dsi_get_pkg_sender(struct mdfld_dsi_config *config)
+{
+	struct mdfld_dsi_connector *dsi_connector;
+
+	if (!config)
+		return NULL;
+
+	dsi_connector = config->connector;
+
+	if (!dsi_connector)
+		return NULL;
+
+	return dsi_connector->pkg_sender;
+}
+
+static inline struct mdfld_dsi_config *
+	mdfld_dsi_encoder_get_config(struct mdfld_dsi_encoder *encoder)
+{
+	if (!encoder)
+		return NULL;
+	return (struct mdfld_dsi_config *)encoder->private;
+}
+
+static inline struct mdfld_dsi_connector *
+	mdfld_dsi_encoder_get_connector(struct mdfld_dsi_encoder *encoder)
+{
+	struct mdfld_dsi_config *config;
+
+	if (!encoder)
+		return NULL;
+
+	config = mdfld_dsi_encoder_get_config(encoder);
+	if (!config)
+		return NULL;
+
+	return config->connector;
+}
+
+static inline void *mdfld_dsi_encoder_get_pkg_sender(
+				struct mdfld_dsi_encoder *encoder)
+{
+	struct mdfld_dsi_config *dsi_config;
+
+	dsi_config = mdfld_dsi_encoder_get_config(encoder);
+	if (!dsi_config)
+		return NULL;
+
+	return mdfld_dsi_get_pkg_sender(dsi_config);
+}
+
+static inline int mdfld_dsi_encoder_get_pipe(struct mdfld_dsi_encoder *encoder)
+{
+	struct mdfld_dsi_connector *connector;
+
+	if (!encoder)
+		return -1;
+
+	connector = mdfld_dsi_encoder_get_connector(encoder);
+	if (!connector)
+		return -1;
+	return connector->pipe;
+}
+
+/* Export functions */
+extern void mdfld_dsi_gen_fifo_ready(struct drm_device *dev,
+					u32 gen_fifo_stat_reg, u32 fifo_stat);
+extern void mdfld_dsi_brightness_init(struct mdfld_dsi_config *dsi_config,
+					int pipe);
+extern void mdfld_dsi_brightness_control(struct drm_device *dev, int pipe,
+					int level);
+extern void mdfld_dsi_output_init(struct drm_device *dev,
+					int pipe,
+					struct mdfld_dsi_config *config,
+					const struct panel_funcs *p_vid_funcs);
+extern void mdfld_dsi_controller_init(struct mdfld_dsi_config *dsi_config,
+					int pipe);
+
+extern int mdfld_dsi_get_power_mode(struct mdfld_dsi_config *dsi_config,
+					u32 *mode, bool hs);
+extern int mdfld_dsi_get_diagnostic_result(struct mdfld_dsi_config *dsi_config,
+					u32 *result, bool hs);
+extern int mdfld_dsi_panel_reset(int pipe);
+
+#endif /*__MDFLD_DSI_OUTPUT_H__*/
diff --git a/drivers/gpu/drm/gma500/mdfld_dsi_pkg_sender.c b/drivers/gpu/drm/gma500/mdfld_dsi_pkg_sender.c
new file mode 100644
index 00000000000..f193acec657
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_dsi_pkg_sender.c
@@ -0,0 +1,694 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * Jackie Li<yaodong.li@intel.com>
+ */
+
+#include <linux/freezer.h>
+
+#include "mdfld_dsi_output.h"
+#include "mdfld_dsi_pkg_sender.h"
+#include "mdfld_dsi_dpi.h"
+
+#define MDFLD_DSI_READ_MAX_COUNT		5000
+
+enum data_type {
+	DSI_DT_GENERIC_SHORT_WRITE_0	= 0x03,
+	DSI_DT_GENERIC_SHORT_WRITE_1	= 0x13,
+	DSI_DT_GENERIC_SHORT_WRITE_2	= 0x23,
+	DSI_DT_GENERIC_READ_0		= 0x04,
+	DSI_DT_GENERIC_READ_1		= 0x14,
+	DSI_DT_GENERIC_READ_2		= 0x24,
+	DSI_DT_GENERIC_LONG_WRITE	= 0x29,
+	DSI_DT_DCS_SHORT_WRITE_0	= 0x05,
+	DSI_DT_DCS_SHORT_WRITE_1	= 0x15,
+	DSI_DT_DCS_READ			= 0x06,
+	DSI_DT_DCS_LONG_WRITE		= 0x39,
+};
+
+enum {
+	MDFLD_DSI_PANEL_MODE_SLEEP = 0x1,
+};
+
+enum {
+	MDFLD_DSI_PKG_SENDER_FREE = 0x0,
+	MDFLD_DSI_PKG_SENDER_BUSY = 0x1,
+};
+
+static const char *const dsi_errors[] = {
+	"RX SOT Error",
+	"RX SOT Sync Error",
+	"RX EOT Sync Error",
+	"RX Escape Mode Entry Error",
+	"RX LP TX Sync Error",
+	"RX HS Receive Timeout Error",
+	"RX False Control Error",
+	"RX ECC Single Bit Error",
+	"RX ECC Multibit Error",
+	"RX Checksum Error",
+	"RX DSI Data Type Not Recognised",
+	"RX DSI VC ID Invalid",
+	"TX False Control Error",
+	"TX ECC Single Bit Error",
+	"TX ECC Multibit Error",
+	"TX Checksum Error",
+	"TX DSI Data Type Not Recognised",
+	"TX DSI VC ID invalid",
+	"High Contention",
+	"Low contention",
+	"DPI FIFO Under run",
+	"HS TX Timeout",
+	"LP RX Timeout",
+	"Turn Around ACK Timeout",
+	"ACK With No Error",
+	"RX Invalid TX Length",
+	"RX Prot Violation",
+	"HS Generic Write FIFO Full",
+	"LP Generic Write FIFO Full",
+	"Generic Read Data Avail"
+	"Special Packet Sent",
+	"Tearing Effect",
+};
+
+static inline int wait_for_gen_fifo_empty(struct mdfld_dsi_pkg_sender *sender,
+						u32 mask)
+{
+	struct drm_device *dev = sender->dev;
+	u32 gen_fifo_stat_reg = sender->mipi_gen_fifo_stat_reg;
+	int retry = 0xffff;
+
+	while (retry--) {
+		if ((mask & REG_READ(gen_fifo_stat_reg)) == mask)
+			return 0;
+		udelay(100);
+	}
+	DRM_ERROR("fifo is NOT empty 0x%08x\n", REG_READ(gen_fifo_stat_reg));
+	return -EIO;
+}
+
+static int wait_for_all_fifos_empty(struct mdfld_dsi_pkg_sender *sender)
+{
+	return wait_for_gen_fifo_empty(sender, (BIT(2) | BIT(10) | BIT(18) |
+						BIT(26) | BIT(27) | BIT(28)));
+}
+
+static int wait_for_lp_fifos_empty(struct mdfld_dsi_pkg_sender *sender)
+{
+	return wait_for_gen_fifo_empty(sender, (BIT(10) | BIT(26)));
+}
+
+static int wait_for_hs_fifos_empty(struct mdfld_dsi_pkg_sender *sender)
+{
+	return wait_for_gen_fifo_empty(sender, (BIT(2) | BIT(18)));
+}
+
+static int handle_dsi_error(struct mdfld_dsi_pkg_sender *sender, u32 mask)
+{
+	u32 intr_stat_reg = sender->mipi_intr_stat_reg;
+	struct drm_device *dev = sender->dev;
+
+	dev_dbg(sender->dev->dev, "Handling error 0x%08x\n", mask);
+
+	switch (mask) {
+	case BIT(0):
+	case BIT(1):
+	case BIT(2):
+	case BIT(3):
+	case BIT(4):
+	case BIT(5):
+	case BIT(6):
+	case BIT(7):
+	case BIT(8):
+	case BIT(9):
+	case BIT(10):
+	case BIT(11):
+	case BIT(12):
+	case BIT(13):
+		dev_dbg(sender->dev->dev, "No Action required\n");
+		break;
+	case BIT(14):
+		/*wait for all fifo empty*/
+		/*wait_for_all_fifos_empty(sender)*/;
+		break;
+	case BIT(15):
+		dev_dbg(sender->dev->dev, "No Action required\n");
+		break;
+	case BIT(16):
+		break;
+	case BIT(17):
+		break;
+	case BIT(18):
+	case BIT(19):
+		dev_dbg(sender->dev->dev, "High/Low contention detected\n");
+		/*wait for contention recovery time*/
+		/*mdelay(10);*/
+		/*wait for all fifo empty*/
+		if (0)
+			wait_for_all_fifos_empty(sender);
+		break;
+	case BIT(20):
+		dev_dbg(sender->dev->dev, "No Action required\n");
+		break;
+	case BIT(21):
+		/*wait for all fifo empty*/
+		/*wait_for_all_fifos_empty(sender);*/
+		break;
+	case BIT(22):
+		break;
+	case BIT(23):
+	case BIT(24):
+	case BIT(25):
+	case BIT(26):
+	case BIT(27):
+		dev_dbg(sender->dev->dev, "HS Gen fifo full\n");
+		REG_WRITE(intr_stat_reg, mask);
+		wait_for_hs_fifos_empty(sender);
+		break;
+	case BIT(28):
+		dev_dbg(sender->dev->dev, "LP Gen fifo full\n");
+		REG_WRITE(intr_stat_reg, mask);
+		wait_for_lp_fifos_empty(sender);
+		break;
+	case BIT(29):
+	case BIT(30):
+	case BIT(31):
+		dev_dbg(sender->dev->dev, "No Action required\n");
+		break;
+	}
+
+	if (mask & REG_READ(intr_stat_reg))
+		dev_dbg(sender->dev->dev,
+				"Cannot clean interrupt 0x%08x\n", mask);
+	return 0;
+}
+
+static int dsi_error_handler(struct mdfld_dsi_pkg_sender *sender)
+{
+	struct drm_device *dev = sender->dev;
+	u32 intr_stat_reg = sender->mipi_intr_stat_reg;
+	u32 mask;
+	u32 intr_stat;
+	int i;
+	int err = 0;
+
+	intr_stat = REG_READ(intr_stat_reg);
+
+	for (i = 0; i < 32; i++) {
+		mask = (0x00000001UL) << i;
+		if (intr_stat & mask) {
+			dev_dbg(sender->dev->dev, "[DSI]: %s\n", dsi_errors[i]);
+			err = handle_dsi_error(sender, mask);
+			if (err)
+				DRM_ERROR("Cannot handle error\n");
+		}
+	}
+	return err;
+}
+
+static int send_short_pkg(struct mdfld_dsi_pkg_sender *sender, u8 data_type,
+			u8 cmd, u8 param, bool hs)
+{
+	struct drm_device *dev = sender->dev;
+	u32 ctrl_reg;
+	u32 val;
+	u8 virtual_channel = 0;
+
+	if (hs) {
+		ctrl_reg = sender->mipi_hs_gen_ctrl_reg;
+
+		/* FIXME: wait_for_hs_fifos_empty(sender); */
+	} else {
+		ctrl_reg = sender->mipi_lp_gen_ctrl_reg;
+
+		/* FIXME: wait_for_lp_fifos_empty(sender); */
+	}
+
+	val = FLD_VAL(param, 23, 16) | FLD_VAL(cmd, 15, 8) |
+		FLD_VAL(virtual_channel, 7, 6) | FLD_VAL(data_type, 5, 0);
+
+	REG_WRITE(ctrl_reg, val);
+
+	return 0;
+}
+
+static int send_long_pkg(struct mdfld_dsi_pkg_sender *sender, u8 data_type,
+			u8 *data, int len, bool hs)
+{
+	struct drm_device *dev = sender->dev;
+	u32 ctrl_reg;
+	u32 data_reg;
+	u32 val;
+	u8 *p;
+	u8 b1, b2, b3, b4;
+	u8 virtual_channel = 0;
+	int i;
+
+	if (hs) {
+		ctrl_reg = sender->mipi_hs_gen_ctrl_reg;
+		data_reg = sender->mipi_hs_gen_data_reg;
+
+		/* FIXME: wait_for_hs_fifos_empty(sender); */
+	} else {
+		ctrl_reg = sender->mipi_lp_gen_ctrl_reg;
+		data_reg = sender->mipi_lp_gen_data_reg;
+
+		/* FIXME: wait_for_lp_fifos_empty(sender); */
+	}
+
+	p = data;
+	for (i = 0; i < len / 4; i++) {
+		b1 = *p++;
+		b2 = *p++;
+		b3 = *p++;
+		b4 = *p++;
+
+		REG_WRITE(data_reg, b4 << 24 | b3 << 16 | b2 << 8 | b1);
+	}
+
+	i = len % 4;
+	if (i) {
+		b1 = 0; b2 = 0; b3 = 0;
+
+		switch (i) {
+		case 3:
+			b1 = *p++;
+			b2 = *p++;
+			b3 = *p++;
+			break;
+		case 2:
+			b1 = *p++;
+			b2 = *p++;
+			break;
+		case 1:
+			b1 = *p++;
+			break;
+		}
+
+		REG_WRITE(data_reg, b3 << 16 | b2 << 8 | b1);
+	}
+
+	val = FLD_VAL(len, 23, 8) | FLD_VAL(virtual_channel, 7, 6) |
+		FLD_VAL(data_type, 5, 0);
+
+	REG_WRITE(ctrl_reg, val);
+
+	return 0;
+}
+
+static int send_pkg_prepare(struct mdfld_dsi_pkg_sender *sender, u8 data_type,
+			u8 *data, u16 len)
+{
+	u8 cmd;
+
+	switch (data_type) {
+	case DSI_DT_DCS_SHORT_WRITE_0:
+	case DSI_DT_DCS_SHORT_WRITE_1:
+	case DSI_DT_DCS_LONG_WRITE:
+		cmd = *data;
+		break;
+	default:
+		return 0;
+	}
+
+	/*this prevents other package sending while doing msleep*/
+	sender->status = MDFLD_DSI_PKG_SENDER_BUSY;
+
+	/*wait for 120 milliseconds in case exit_sleep_mode just be sent*/
+	if (unlikely(cmd == DCS_ENTER_SLEEP_MODE)) {
+		/*TODO: replace it with msleep later*/
+		mdelay(120);
+	}
+
+	if (unlikely(cmd == DCS_EXIT_SLEEP_MODE)) {
+		/*TODO: replace it with msleep later*/
+		mdelay(120);
+	}
+	return 0;
+}
+
+static int send_pkg_done(struct mdfld_dsi_pkg_sender *sender, u8 data_type,
+			u8 *data, u16 len)
+{
+	u8 cmd;
+
+	switch (data_type) {
+	case DSI_DT_DCS_SHORT_WRITE_0:
+	case DSI_DT_DCS_SHORT_WRITE_1:
+	case DSI_DT_DCS_LONG_WRITE:
+		cmd = *data;
+		break;
+	default:
+		return 0;
+	}
+
+	/*update panel status*/
+	if (unlikely(cmd == DCS_ENTER_SLEEP_MODE)) {
+		sender->panel_mode |= MDFLD_DSI_PANEL_MODE_SLEEP;
+		/*TODO: replace it with msleep later*/
+		mdelay(120);
+	} else if (unlikely(cmd == DCS_EXIT_SLEEP_MODE)) {
+		sender->panel_mode &= ~MDFLD_DSI_PANEL_MODE_SLEEP;
+		/*TODO: replace it with msleep later*/
+		mdelay(120);
+	} else if (unlikely(cmd == DCS_SOFT_RESET)) {
+		/*TODO: replace it with msleep later*/
+		mdelay(5);
+	}
+
+	sender->status = MDFLD_DSI_PKG_SENDER_FREE;
+
+	return 0;
+}
+
+static int send_pkg(struct mdfld_dsi_pkg_sender *sender, u8 data_type,
+		u8 *data, u16 len, bool hs)
+{
+	int ret;
+
+	/*handle DSI error*/
+	ret = dsi_error_handler(sender);
+	if (ret) {
+		DRM_ERROR("Error handling failed\n");
+		return -EAGAIN;
+	}
+
+	/* send pkg */
+	if (sender->status == MDFLD_DSI_PKG_SENDER_BUSY) {
+		DRM_ERROR("sender is busy\n");
+		return -EAGAIN;
+	}
+
+	ret = send_pkg_prepare(sender, data_type, data, len);
+	if (ret) {
+		DRM_ERROR("send_pkg_prepare error\n");
+		return ret;
+	}
+
+	switch (data_type) {
+	case DSI_DT_GENERIC_SHORT_WRITE_0:
+	case DSI_DT_GENERIC_SHORT_WRITE_1:
+	case DSI_DT_GENERIC_SHORT_WRITE_2:
+	case DSI_DT_GENERIC_READ_0:
+	case DSI_DT_GENERIC_READ_1:
+	case DSI_DT_GENERIC_READ_2:
+	case DSI_DT_DCS_SHORT_WRITE_0:
+	case DSI_DT_DCS_SHORT_WRITE_1:
+	case DSI_DT_DCS_READ:
+		ret = send_short_pkg(sender, data_type, data[0], data[1], hs);
+		break;
+	case DSI_DT_GENERIC_LONG_WRITE:
+	case DSI_DT_DCS_LONG_WRITE:
+		ret = send_long_pkg(sender, data_type, data, len, hs);
+		break;
+	}
+
+	send_pkg_done(sender, data_type, data, len);
+
+	/*FIXME: should I query complete and fifo empty here?*/
+
+	return ret;
+}
+
+int mdfld_dsi_send_mcs_long(struct mdfld_dsi_pkg_sender *sender, u8 *data,
+			u32 len, bool hs)
+{
+	unsigned long flags;
+
+	if (!sender || !data || !len) {
+		DRM_ERROR("Invalid parameters\n");
+		return -EINVAL;
+	}
+
+	spin_lock_irqsave(&sender->lock, flags);
+	send_pkg(sender, DSI_DT_DCS_LONG_WRITE, data, len, hs);
+	spin_unlock_irqrestore(&sender->lock, flags);
+
+	return 0;
+}
+
+int mdfld_dsi_send_mcs_short(struct mdfld_dsi_pkg_sender *sender, u8 cmd,
+			u8 param, u8 param_num, bool hs)
+{
+	u8 data[2];
+	unsigned long flags;
+	u8 data_type;
+
+	if (!sender) {
+		DRM_ERROR("Invalid parameter\n");
+		return -EINVAL;
+	}
+
+	data[0] = cmd;
+
+	if (param_num) {
+		data_type = DSI_DT_DCS_SHORT_WRITE_1;
+		data[1] = param;
+	} else {
+		data_type = DSI_DT_DCS_SHORT_WRITE_0;
+		data[1] = 0;
+	}
+
+	spin_lock_irqsave(&sender->lock, flags);
+	send_pkg(sender, data_type, data, sizeof(data), hs);
+	spin_unlock_irqrestore(&sender->lock, flags);
+
+	return 0;
+}
+
+int mdfld_dsi_send_gen_short(struct mdfld_dsi_pkg_sender *sender, u8 param0,
+			u8 param1, u8 param_num, bool hs)
+{
+	u8 data[2];
+	unsigned long flags;
+	u8 data_type;
+
+	if (!sender || param_num < 0 || param_num > 2) {
+		DRM_ERROR("Invalid parameter\n");
+		return -EINVAL;
+	}
+
+	switch (param_num) {
+	case 0:
+		data_type = DSI_DT_GENERIC_SHORT_WRITE_0;
+		data[0] = 0;
+		data[1] = 0;
+		break;
+	case 1:
+		data_type = DSI_DT_GENERIC_SHORT_WRITE_1;
+		data[0] = param0;
+		data[1] = 0;
+		break;
+	case 2:
+		data_type = DSI_DT_GENERIC_SHORT_WRITE_2;
+		data[0] = param0;
+		data[1] = param1;
+		break;
+	}
+
+	spin_lock_irqsave(&sender->lock, flags);
+	send_pkg(sender, data_type, data, sizeof(data), hs);
+	spin_unlock_irqrestore(&sender->lock, flags);
+
+	return 0;
+}
+
+int mdfld_dsi_send_gen_long(struct mdfld_dsi_pkg_sender *sender, u8 *data,
+			u32 len, bool hs)
+{
+	unsigned long flags;
+
+	if (!sender || !data || !len) {
+		DRM_ERROR("Invalid parameters\n");
+		return -EINVAL;
+	}
+
+	spin_lock_irqsave(&sender->lock, flags);
+	send_pkg(sender, DSI_DT_GENERIC_LONG_WRITE, data, len, hs);
+	spin_unlock_irqrestore(&sender->lock, flags);
+
+	return 0;
+}
+
+static int __read_panel_data(struct mdfld_dsi_pkg_sender *sender, u8 data_type,
+			u8 *data, u16 len, u32 *data_out, u16 len_out, bool hs)
+{
+	unsigned long flags;
+	struct drm_device *dev = sender->dev;
+	int i;
+	u32 gen_data_reg;
+	int retry = MDFLD_DSI_READ_MAX_COUNT;
+
+	if (!sender || !data_out || !len_out) {
+		DRM_ERROR("Invalid parameters\n");
+		return -EINVAL;
+	}
+
+	/**
+	 * do reading.
+	 * 0) send out generic read request
+	 * 1) polling read data avail interrupt
+	 * 2) read data
+	 */
+	spin_lock_irqsave(&sender->lock, flags);
+
+	REG_WRITE(sender->mipi_intr_stat_reg, BIT(29));
+
+	if ((REG_READ(sender->mipi_intr_stat_reg) & BIT(29)))
+		DRM_ERROR("Can NOT clean read data valid interrupt\n");
+
+	/*send out read request*/
+	send_pkg(sender, data_type, data, len, hs);
+
+	/*polling read data avail interrupt*/
+	while (retry && !(REG_READ(sender->mipi_intr_stat_reg) & BIT(29))) {
+		udelay(100);
+		retry--;
+	}
+
+	if (!retry) {
+		spin_unlock_irqrestore(&sender->lock, flags);
+		return -ETIMEDOUT;
+	}
+
+	REG_WRITE(sender->mipi_intr_stat_reg, BIT(29));
+
+	/*read data*/
+	if (hs)
+		gen_data_reg = sender->mipi_hs_gen_data_reg;
+	else
+		gen_data_reg = sender->mipi_lp_gen_data_reg;
+
+	for (i = 0; i < len_out; i++)
+		*(data_out + i) = REG_READ(gen_data_reg);
+
+	spin_unlock_irqrestore(&sender->lock, flags);
+
+	return 0;
+}
+
+int mdfld_dsi_read_mcs(struct mdfld_dsi_pkg_sender *sender, u8 cmd,
+		u32 *data, u16 len, bool hs)
+{
+	if (!sender || !data || !len) {
+		DRM_ERROR("Invalid parameters\n");
+		return -EINVAL;
+	}
+
+	return __read_panel_data(sender, DSI_DT_DCS_READ, &cmd, 1,
+				data, len, hs);
+}
+
+int mdfld_dsi_pkg_sender_init(struct mdfld_dsi_connector *dsi_connector,
+								int pipe)
+{
+	struct mdfld_dsi_pkg_sender *pkg_sender;
+	struct mdfld_dsi_config *dsi_config =
+				mdfld_dsi_get_config(dsi_connector);
+	struct drm_device *dev = dsi_config->dev;
+	u32 mipi_val = 0;
+
+	if (!dsi_connector) {
+		DRM_ERROR("Invalid parameter\n");
+		return -EINVAL;
+	}
+
+	pkg_sender = dsi_connector->pkg_sender;
+
+	if (!pkg_sender || IS_ERR(pkg_sender)) {
+		pkg_sender = kzalloc(sizeof(struct mdfld_dsi_pkg_sender),
+								GFP_KERNEL);
+		if (!pkg_sender) {
+			DRM_ERROR("Create DSI pkg sender failed\n");
+			return -ENOMEM;
+		}
+		dsi_connector->pkg_sender = (void *)pkg_sender;
+	}
+
+	pkg_sender->dev = dev;
+	pkg_sender->dsi_connector = dsi_connector;
+	pkg_sender->pipe = pipe;
+	pkg_sender->pkg_num = 0;
+	pkg_sender->panel_mode = 0;
+	pkg_sender->status = MDFLD_DSI_PKG_SENDER_FREE;
+
+	/*init regs*/
+	if (pipe == 0) {
+		pkg_sender->dpll_reg = MRST_DPLL_A;
+		pkg_sender->dspcntr_reg = DSPACNTR;
+		pkg_sender->pipeconf_reg = PIPEACONF;
+		pkg_sender->dsplinoff_reg = DSPALINOFF;
+		pkg_sender->dspsurf_reg = DSPASURF;
+		pkg_sender->pipestat_reg = PIPEASTAT;
+	} else if (pipe == 2) {
+		pkg_sender->dpll_reg = MRST_DPLL_A;
+		pkg_sender->dspcntr_reg = DSPCCNTR;
+		pkg_sender->pipeconf_reg = PIPECCONF;
+		pkg_sender->dsplinoff_reg = DSPCLINOFF;
+		pkg_sender->dspsurf_reg = DSPCSURF;
+		pkg_sender->pipestat_reg = PIPECSTAT;
+	}
+
+	pkg_sender->mipi_intr_stat_reg = MIPI_INTR_STAT_REG(pipe);
+	pkg_sender->mipi_lp_gen_data_reg = MIPI_LP_GEN_DATA_REG(pipe);
+	pkg_sender->mipi_hs_gen_data_reg = MIPI_HS_GEN_DATA_REG(pipe);
+	pkg_sender->mipi_lp_gen_ctrl_reg = MIPI_LP_GEN_CTRL_REG(pipe);
+	pkg_sender->mipi_hs_gen_ctrl_reg = MIPI_HS_GEN_CTRL_REG(pipe);
+	pkg_sender->mipi_gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
+	pkg_sender->mipi_data_addr_reg = MIPI_DATA_ADD_REG(pipe);
+	pkg_sender->mipi_data_len_reg = MIPI_DATA_LEN_REG(pipe);
+	pkg_sender->mipi_cmd_addr_reg = MIPI_CMD_ADD_REG(pipe);
+	pkg_sender->mipi_cmd_len_reg = MIPI_CMD_LEN_REG(pipe);
+
+	/*init lock*/
+	spin_lock_init(&pkg_sender->lock);
+
+	if (mdfld_get_panel_type(dev, pipe) != TC35876X) {
+		/**
+		 * For video mode, don't enable DPI timing output here,
+		 * will init the DPI timing output during mode setting.
+		 */
+		mipi_val = PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX;
+
+		if (pipe == 0)
+			mipi_val |= 0x2;
+
+		REG_WRITE(MIPI_PORT_CONTROL(pipe), mipi_val);
+		REG_READ(MIPI_PORT_CONTROL(pipe));
+
+		/* do dsi controller init */
+		mdfld_dsi_controller_init(dsi_config, pipe);
+	}
+
+	return 0;
+}
+
+void mdfld_dsi_pkg_sender_destroy(struct mdfld_dsi_pkg_sender *sender)
+{
+	if (!sender || IS_ERR(sender))
+		return;
+
+	/*free*/
+	kfree(sender);
+}
+
+
diff --git a/drivers/gpu/drm/gma500/mdfld_dsi_pkg_sender.h b/drivers/gpu/drm/gma500/mdfld_dsi_pkg_sender.h
new file mode 100644
index 00000000000..459cd7ea8b8
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_dsi_pkg_sender.h
@@ -0,0 +1,92 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * Jackie Li<yaodong.li@intel.com>
+ */
+#ifndef __MDFLD_DSI_PKG_SENDER_H__
+#define __MDFLD_DSI_PKG_SENDER_H__
+
+#include <linux/kthread.h>
+
+#define MDFLD_MAX_DCS_PARAM	8
+
+struct mdfld_dsi_pkg_sender {
+	struct drm_device *dev;
+	struct mdfld_dsi_connector *dsi_connector;
+	u32 status;
+	u32 panel_mode;
+
+	int pipe;
+
+	spinlock_t lock;
+
+	u32 pkg_num;
+
+	/* Registers */
+	u32 dpll_reg;
+	u32 dspcntr_reg;
+	u32 pipeconf_reg;
+	u32 pipestat_reg;
+	u32 dsplinoff_reg;
+	u32 dspsurf_reg;
+
+	u32 mipi_intr_stat_reg;
+	u32 mipi_lp_gen_data_reg;
+	u32 mipi_hs_gen_data_reg;
+	u32 mipi_lp_gen_ctrl_reg;
+	u32 mipi_hs_gen_ctrl_reg;
+	u32 mipi_gen_fifo_stat_reg;
+	u32 mipi_data_addr_reg;
+	u32 mipi_data_len_reg;
+	u32 mipi_cmd_addr_reg;
+	u32 mipi_cmd_len_reg;
+};
+
+/* DCS definitions */
+#define DCS_SOFT_RESET			0x01
+#define DCS_ENTER_SLEEP_MODE		0x10
+#define DCS_EXIT_SLEEP_MODE		0x11
+#define DCS_SET_DISPLAY_OFF		0x28
+#define DCS_SET_DISPLAY_ON		0x29
+#define DCS_SET_COLUMN_ADDRESS		0x2a
+#define DCS_SET_PAGE_ADDRESS		0x2b
+#define DCS_WRITE_MEM_START		0x2c
+#define DCS_SET_TEAR_OFF		0x34
+#define DCS_SET_TEAR_ON			0x35
+
+extern int mdfld_dsi_pkg_sender_init(struct mdfld_dsi_connector *dsi_connector,
+					int pipe);
+extern void mdfld_dsi_pkg_sender_destroy(struct mdfld_dsi_pkg_sender *sender);
+int mdfld_dsi_send_mcs_short(struct mdfld_dsi_pkg_sender *sender, u8 cmd,
+					u8 param, u8 param_num, bool hs);
+int mdfld_dsi_send_mcs_long(struct mdfld_dsi_pkg_sender *sender, u8 *data,
+					u32 len, bool hs);
+int mdfld_dsi_send_gen_short(struct mdfld_dsi_pkg_sender *sender, u8 param0,
+					u8 param1, u8 param_num, bool hs);
+int mdfld_dsi_send_gen_long(struct mdfld_dsi_pkg_sender *sender, u8 *data,
+					u32 len, bool hs);
+/* Read interfaces */
+int mdfld_dsi_read_mcs(struct mdfld_dsi_pkg_sender *sender, u8 cmd,
+		u32 *data, u16 len, bool hs);
+
+#endif
diff --git a/drivers/gpu/drm/gma500/mdfld_intel_display.c b/drivers/gpu/drm/gma500/mdfld_intel_display.c
new file mode 100644
index 00000000000..55e5af5cbd3
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_intel_display.c
@@ -0,0 +1,1192 @@
+/*
+ * Copyright © 2006-2007 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * Authors:
+ *	Eric Anholt <eric@anholt.net>
+ */
+
+#include <linux/i2c.h>
+#include <linux/pm_runtime.h>
+
+#include <drm/drmP.h>
+#include "psb_intel_reg.h"
+#include "psb_intel_display.h"
+#include "framebuffer.h"
+#include "mdfld_output.h"
+#include "mdfld_dsi_output.h"
+
+/* Hardcoded currently */
+static int ksel = KSEL_CRYSTAL_19;
+
+struct psb_intel_range_t {
+	int min, max;
+};
+
+struct mrst_limit_t {
+	struct psb_intel_range_t dot, m, p1;
+};
+
+struct mrst_clock_t {
+	/* derived values */
+	int dot;
+	int m;
+	int p1;
+};
+
+#define COUNT_MAX 0x10000000
+
+void mdfldWaitForPipeDisable(struct drm_device *dev, int pipe)
+{
+	int count, temp;
+	u32 pipeconf_reg = PIPEACONF;
+
+	switch (pipe) {
+	case 0:
+		break;
+	case 1:
+		pipeconf_reg = PIPEBCONF;
+		break;
+	case 2:
+		pipeconf_reg = PIPECCONF;
+		break;
+	default:
+		DRM_ERROR("Illegal Pipe Number.\n");
+		return;
+	}
+
+	/* FIXME JLIU7_PO */
+	psb_intel_wait_for_vblank(dev);
+	return;
+
+	/* Wait for for the pipe disable to take effect. */
+	for (count = 0; count < COUNT_MAX; count++) {
+		temp = REG_READ(pipeconf_reg);
+		if ((temp & PIPEACONF_PIPE_STATE) == 0)
+			break;
+	}
+}
+
+void mdfldWaitForPipeEnable(struct drm_device *dev, int pipe)
+{
+	int count, temp;
+	u32 pipeconf_reg = PIPEACONF;
+
+	switch (pipe) {
+	case 0:
+		break;
+	case 1:
+		pipeconf_reg = PIPEBCONF;
+		break;
+	case 2:
+		pipeconf_reg = PIPECCONF;
+		break;
+	default:
+		DRM_ERROR("Illegal Pipe Number.\n");
+		return;
+	}
+
+	/* FIXME JLIU7_PO */
+	psb_intel_wait_for_vblank(dev);
+	return;
+
+	/* Wait for for the pipe enable to take effect. */
+	for (count = 0; count < COUNT_MAX; count++) {
+		temp = REG_READ(pipeconf_reg);
+		if ((temp & PIPEACONF_PIPE_STATE) == 1)
+			break;
+	}
+}
+
+static void psb_intel_crtc_prepare(struct drm_crtc *crtc)
+{
+	struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
+	crtc_funcs->dpms(crtc, DRM_MODE_DPMS_OFF);
+}
+
+static void psb_intel_crtc_commit(struct drm_crtc *crtc)
+{
+	struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
+	crtc_funcs->dpms(crtc, DRM_MODE_DPMS_ON);
+}
+
+static bool psb_intel_crtc_mode_fixup(struct drm_crtc *crtc,
+				  struct drm_display_mode *mode,
+				  struct drm_display_mode *adjusted_mode)
+{
+	return true;
+}
+
+/**
+ * Return the pipe currently connected to the panel fitter,
+ * or -1 if the panel fitter is not present or not in use
+ */
+static int psb_intel_panel_fitter_pipe(struct drm_device *dev)
+{
+	u32 pfit_control;
+
+	pfit_control = REG_READ(PFIT_CONTROL);
+
+	/* See if the panel fitter is in use */
+	if ((pfit_control & PFIT_ENABLE) == 0)
+		return -1;
+
+	/* 965 can place panel fitter on either pipe */
+	return (pfit_control >> 29) & 0x3;
+}
+
+static struct drm_device globle_dev;
+
+void mdfld__intel_plane_set_alpha(int enable)
+{
+	struct drm_device *dev = &globle_dev;
+	int dspcntr_reg = DSPACNTR;
+	u32 dspcntr;
+
+	dspcntr = REG_READ(dspcntr_reg);
+
+	if (enable) {
+		dspcntr &= ~DISPPLANE_32BPP_NO_ALPHA;
+		dspcntr |= DISPPLANE_32BPP;
+	} else {
+		dspcntr &= ~DISPPLANE_32BPP;
+		dspcntr |= DISPPLANE_32BPP_NO_ALPHA;
+	}
+
+	REG_WRITE(dspcntr_reg, dspcntr);
+}
+
+static int check_fb(struct drm_framebuffer *fb)
+{
+	if (!fb)
+		return 0;
+
+	switch (fb->bits_per_pixel) {
+	case 8:
+	case 16:
+	case 24:
+	case 32:
+		return 0;
+	default:
+		DRM_ERROR("Unknown color depth\n");
+		return -EINVAL;
+	}
+}
+
+static int mdfld__intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
+				struct drm_framebuffer *old_fb)
+{
+	struct drm_device *dev = crtc->dev;
+	/* struct drm_i915_master_private *master_priv; */
+	struct psb_intel_crtc *psb_intel_crtc = to_psb_intel_crtc(crtc);
+	struct psb_framebuffer *psbfb = to_psb_fb(crtc->fb);
+	int pipe = psb_intel_crtc->pipe;
+	unsigned long start, offset;
+	int dsplinoff = DSPALINOFF;
+	int dspsurf = DSPASURF;
+	int dspstride = DSPASTRIDE;
+	int dspcntr_reg = DSPACNTR;
+	u32 dspcntr;
+	int ret;
+
+	memcpy(&globle_dev, dev, sizeof(struct drm_device));
+
+	dev_dbg(dev->dev, "pipe = 0x%x.\n", pipe);
+
+	/* no fb bound */
+	if (!crtc->fb) {
+		dev_dbg(dev->dev, "No FB bound\n");
+		return 0;
+	}
+
+	ret = check_fb(crtc->fb);
+	if (ret)
+		return ret;
+
+	switch (pipe) {
+	case 0:
+		dsplinoff = DSPALINOFF;
+		break;
+	case 1:
+		dsplinoff = DSPBLINOFF;
+		dspsurf = DSPBSURF;
+		dspstride = DSPBSTRIDE;
+		dspcntr_reg = DSPBCNTR;
+		break;
+	case 2:
+		dsplinoff = DSPCLINOFF;
+		dspsurf = DSPCSURF;
+		dspstride = DSPCSTRIDE;
+		dspcntr_reg = DSPCCNTR;
+		break;
+	default:
+		DRM_ERROR("Illegal Pipe Number.\n");
+		return -EINVAL;
+	}
+
+	if (!gma_power_begin(dev, true))
+		return 0;
+
+	start = psbfb->gtt->offset;
+	offset = y * crtc->fb->pitches[0] + x * (crtc->fb->bits_per_pixel / 8);
+
+	REG_WRITE(dspstride, crtc->fb->pitches[0]);
+	dspcntr = REG_READ(dspcntr_reg);
+	dspcntr &= ~DISPPLANE_PIXFORMAT_MASK;
+
+	switch (crtc->fb->bits_per_pixel) {
+	case 8:
+		dspcntr |= DISPPLANE_8BPP;
+		break;
+	case 16:
+		if (crtc->fb->depth == 15)
+			dspcntr |= DISPPLANE_15_16BPP;
+		else
+			dspcntr |= DISPPLANE_16BPP;
+		break;
+	case 24:
+	case 32:
+		dspcntr |= DISPPLANE_32BPP_NO_ALPHA;
+		break;
+	}
+	REG_WRITE(dspcntr_reg, dspcntr);
+
+	dev_dbg(dev->dev, "Writing base %08lX %08lX %d %d\n",
+						start, offset, x, y);
+	REG_WRITE(dsplinoff, offset);
+	REG_READ(dsplinoff);
+	REG_WRITE(dspsurf, start);
+	REG_READ(dspsurf);
+
+	gma_power_end(dev);
+
+	return 0;
+}
+
+/*
+ * Disable the pipe, plane and pll.
+ *
+ */
+void mdfld_disable_crtc(struct drm_device *dev, int pipe)
+{
+	int dpll_reg = MRST_DPLL_A;
+	int dspcntr_reg = DSPACNTR;
+	int dspbase_reg = MRST_DSPABASE;
+	int pipeconf_reg = PIPEACONF;
+	u32 temp;
+
+	dev_dbg(dev->dev, "pipe = %d\n", pipe);
+
+
+	switch (pipe) {
+	case 0:
+		break;
+	case 1:
+		dpll_reg = MDFLD_DPLL_B;
+		dspcntr_reg = DSPBCNTR;
+		dspbase_reg = DSPBSURF;
+		pipeconf_reg = PIPEBCONF;
+		break;
+	case 2:
+		dpll_reg = MRST_DPLL_A;
+		dspcntr_reg = DSPCCNTR;
+		dspbase_reg = MDFLD_DSPCBASE;
+		pipeconf_reg = PIPECCONF;
+		break;
+	default:
+		DRM_ERROR("Illegal Pipe Number.\n");
+		return;
+	}
+
+	if (pipe != 1)
+		mdfld_dsi_gen_fifo_ready(dev, MIPI_GEN_FIFO_STAT_REG(pipe),
+				HS_CTRL_FIFO_EMPTY | HS_DATA_FIFO_EMPTY);
+
+	/* Disable display plane */
+	temp = REG_READ(dspcntr_reg);
+	if ((temp & DISPLAY_PLANE_ENABLE) != 0) {
+		REG_WRITE(dspcntr_reg,
+			  temp & ~DISPLAY_PLANE_ENABLE);
+		/* Flush the plane changes */
+		REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+		REG_READ(dspbase_reg);
+	}
+
+	/* FIXME_JLIU7 MDFLD_PO revisit */
+
+	/* Next, disable display pipes */
+	temp = REG_READ(pipeconf_reg);
+	if ((temp & PIPEACONF_ENABLE) != 0) {
+		temp &= ~PIPEACONF_ENABLE;
+		temp |= PIPECONF_PLANE_OFF | PIPECONF_CURSOR_OFF;
+		REG_WRITE(pipeconf_reg, temp);
+		REG_READ(pipeconf_reg);
+
+		/* Wait for for the pipe disable to take effect. */
+		mdfldWaitForPipeDisable(dev, pipe);
+	}
+
+	temp = REG_READ(dpll_reg);
+	if (temp & DPLL_VCO_ENABLE) {
+		if ((pipe != 1 &&
+			!((REG_READ(PIPEACONF) | REG_READ(PIPECCONF))
+				& PIPEACONF_ENABLE)) || pipe == 1) {
+			temp &= ~(DPLL_VCO_ENABLE);
+			REG_WRITE(dpll_reg, temp);
+			REG_READ(dpll_reg);
+			/* Wait for the clocks to turn off. */
+			/* FIXME_MDFLD PO may need more delay */
+			udelay(500);
+
+			if (!(temp & MDFLD_PWR_GATE_EN)) {
+				/* gating power of DPLL */
+				REG_WRITE(dpll_reg, temp | MDFLD_PWR_GATE_EN);
+				/* FIXME_MDFLD PO - change 500 to 1 after PO */
+				udelay(5000);
+			}
+		}
+	}
+
+}
+
+/**
+ * Sets the power management mode of the pipe and plane.
+ *
+ * This code should probably grow support for turning the cursor off and back
+ * on appropriately at the same time as we're turning the pipe off/on.
+ */
+static void mdfld_crtc_dpms(struct drm_crtc *crtc, int mode)
+{
+	struct drm_device *dev = crtc->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	struct psb_intel_crtc *psb_intel_crtc = to_psb_intel_crtc(crtc);
+	int pipe = psb_intel_crtc->pipe;
+	int dpll_reg = MRST_DPLL_A;
+	int dspcntr_reg = DSPACNTR;
+	int dspbase_reg = MRST_DSPABASE;
+	int pipeconf_reg = PIPEACONF;
+	u32 pipestat_reg = PIPEASTAT;
+	u32 pipeconf = dev_priv->pipeconf[pipe];
+	u32 temp;
+	bool enabled;
+	int timeout = 0;
+
+	dev_dbg(dev->dev, "mode = %d, pipe = %d\n", mode, pipe);
+
+/* FIXME_JLIU7 MDFLD_PO replaced w/ the following function */
+/* mdfld_dbi_dpms (struct drm_device *dev, int pipe, bool enabled) */
+
+	switch (pipe) {
+	case 0:
+		break;
+	case 1:
+		dpll_reg = DPLL_B;
+		dspcntr_reg = DSPBCNTR;
+		dspbase_reg = MRST_DSPBBASE;
+		pipeconf_reg = PIPEBCONF;
+		dpll_reg = MDFLD_DPLL_B;
+		break;
+	case 2:
+		dpll_reg = MRST_DPLL_A;
+		dspcntr_reg = DSPCCNTR;
+		dspbase_reg = MDFLD_DSPCBASE;
+		pipeconf_reg = PIPECCONF;
+		pipestat_reg = PIPECSTAT;
+		break;
+	default:
+		DRM_ERROR("Illegal Pipe Number.\n");
+		return;
+	}
+
+	if (!gma_power_begin(dev, true))
+		return;
+
+	/* XXX: When our outputs are all unaware of DPMS modes other than off
+	 * and on, we should map those modes to DRM_MODE_DPMS_OFF in the CRTC.
+	 */
+	switch (mode) {
+	case DRM_MODE_DPMS_ON:
+	case DRM_MODE_DPMS_STANDBY:
+	case DRM_MODE_DPMS_SUSPEND:
+		/* Enable the DPLL */
+		temp = REG_READ(dpll_reg);
+
+		if ((temp & DPLL_VCO_ENABLE) == 0) {
+			/* When ungating power of DPLL, needs to wait 0.5us
+			   before enable the VCO */
+			if (temp & MDFLD_PWR_GATE_EN) {
+				temp &= ~MDFLD_PWR_GATE_EN;
+				REG_WRITE(dpll_reg, temp);
+				/* FIXME_MDFLD PO - change 500 to 1 after PO */
+				udelay(500);
+			}
+
+			REG_WRITE(dpll_reg, temp);
+			REG_READ(dpll_reg);
+			/* FIXME_MDFLD PO - change 500 to 1 after PO */
+			udelay(500);
+
+			REG_WRITE(dpll_reg, temp | DPLL_VCO_ENABLE);
+			REG_READ(dpll_reg);
+
+			/**
+			 * wait for DSI PLL to lock
+			 * NOTE: only need to poll status of pipe 0 and pipe 1,
+			 * since both MIPI pipes share the same PLL.
+			 */
+			while ((pipe != 2) && (timeout < 20000) &&
+			  !(REG_READ(pipeconf_reg) & PIPECONF_DSIPLL_LOCK)) {
+				udelay(150);
+				timeout++;
+			}
+		}
+
+		/* Enable the plane */
+		temp = REG_READ(dspcntr_reg);
+		if ((temp & DISPLAY_PLANE_ENABLE) == 0) {
+			REG_WRITE(dspcntr_reg,
+				temp | DISPLAY_PLANE_ENABLE);
+			/* Flush the plane changes */
+			REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+		}
+
+		/* Enable the pipe */
+		temp = REG_READ(pipeconf_reg);
+		if ((temp & PIPEACONF_ENABLE) == 0) {
+			REG_WRITE(pipeconf_reg, pipeconf);
+
+			/* Wait for for the pipe enable to take effect. */
+			mdfldWaitForPipeEnable(dev, pipe);
+		}
+
+		/*workaround for sighting 3741701 Random X blank display*/
+		/*perform w/a in video mode only on pipe A or C*/
+		if (pipe == 0 || pipe == 2) {
+			REG_WRITE(pipestat_reg, REG_READ(pipestat_reg));
+			msleep(100);
+			if (PIPE_VBLANK_STATUS & REG_READ(pipestat_reg))
+				dev_dbg(dev->dev, "OK");
+			else {
+				dev_dbg(dev->dev, "STUCK!!!!");
+				/*shutdown controller*/
+				temp = REG_READ(dspcntr_reg);
+				REG_WRITE(dspcntr_reg,
+						temp & ~DISPLAY_PLANE_ENABLE);
+				REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+				/*mdfld_dsi_dpi_shut_down(dev, pipe);*/
+				REG_WRITE(0xb048, 1);
+				msleep(100);
+				temp = REG_READ(pipeconf_reg);
+				temp &= ~PIPEACONF_ENABLE;
+				REG_WRITE(pipeconf_reg, temp);
+				msleep(100); /*wait for pipe disable*/
+				REG_WRITE(MIPI_DEVICE_READY_REG(pipe), 0);
+				msleep(100);
+				REG_WRITE(0xb004, REG_READ(0xb004));
+				/* try to bring the controller back up again*/
+				REG_WRITE(MIPI_DEVICE_READY_REG(pipe), 1);
+				temp = REG_READ(dspcntr_reg);
+				REG_WRITE(dspcntr_reg,
+						temp | DISPLAY_PLANE_ENABLE);
+				REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+				/*mdfld_dsi_dpi_turn_on(dev, pipe);*/
+				REG_WRITE(0xb048, 2);
+				msleep(100);
+				temp = REG_READ(pipeconf_reg);
+				temp |= PIPEACONF_ENABLE;
+				REG_WRITE(pipeconf_reg, temp);
+			}
+		}
+
+		psb_intel_crtc_load_lut(crtc);
+
+		/* Give the overlay scaler a chance to enable
+		   if it's on this pipe */
+		/* psb_intel_crtc_dpms_video(crtc, true); TODO */
+
+		break;
+	case DRM_MODE_DPMS_OFF:
+		/* Give the overlay scaler a chance to disable
+		 * if it's on this pipe */
+		/* psb_intel_crtc_dpms_video(crtc, FALSE); TODO */
+		if (pipe != 1)
+			mdfld_dsi_gen_fifo_ready(dev,
+				MIPI_GEN_FIFO_STAT_REG(pipe),
+				HS_CTRL_FIFO_EMPTY | HS_DATA_FIFO_EMPTY);
+
+		/* Disable the VGA plane that we never use */
+		REG_WRITE(VGACNTRL, VGA_DISP_DISABLE);
+
+		/* Disable display plane */
+		temp = REG_READ(dspcntr_reg);
+		if ((temp & DISPLAY_PLANE_ENABLE) != 0) {
+			REG_WRITE(dspcntr_reg,
+				  temp & ~DISPLAY_PLANE_ENABLE);
+			/* Flush the plane changes */
+			REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
+			REG_READ(dspbase_reg);
+		}
+
+		/* Next, disable display pipes */
+		temp = REG_READ(pipeconf_reg);
+		if ((temp & PIPEACONF_ENABLE) != 0) {
+			temp &= ~PIPEACONF_ENABLE;
+			temp |= PIPECONF_PLANE_OFF | PIPECONF_CURSOR_OFF;
+			REG_WRITE(pipeconf_reg, temp);
+			REG_READ(pipeconf_reg);
+
+			/* Wait for for the pipe disable to take effect. */
+			mdfldWaitForPipeDisable(dev, pipe);
+		}
+
+		temp = REG_READ(dpll_reg);
+		if (temp & DPLL_VCO_ENABLE) {
+			if ((pipe != 1 && !((REG_READ(PIPEACONF)
+				| REG_READ(PIPECCONF)) & PIPEACONF_ENABLE))
+					|| pipe == 1) {
+				temp &= ~(DPLL_VCO_ENABLE);
+				REG_WRITE(dpll_reg, temp);
+				REG_READ(dpll_reg);
+				/* Wait for the clocks to turn off. */
+				/* FIXME_MDFLD PO may need more delay */
+				udelay(500);
+			}
+		}
+		break;
+	}
+	enabled = crtc->enabled && mode != DRM_MODE_DPMS_OFF;
+	gma_power_end(dev);
+}
+
+
+#define MDFLD_LIMT_DPLL_19	    0
+#define MDFLD_LIMT_DPLL_25	    1
+#define MDFLD_LIMT_DPLL_83	    2
+#define MDFLD_LIMT_DPLL_100	    3
+#define MDFLD_LIMT_DSIPLL_19	    4
+#define MDFLD_LIMT_DSIPLL_25	    5
+#define MDFLD_LIMT_DSIPLL_83	    6
+#define MDFLD_LIMT_DSIPLL_100	    7
+
+#define MDFLD_DOT_MIN		  19750
+#define MDFLD_DOT_MAX		  120000
+#define MDFLD_DPLL_M_MIN_19	    113
+#define MDFLD_DPLL_M_MAX_19	    155
+#define MDFLD_DPLL_P1_MIN_19	    2
+#define MDFLD_DPLL_P1_MAX_19	    10
+#define MDFLD_DPLL_M_MIN_25	    101
+#define MDFLD_DPLL_M_MAX_25	    130
+#define MDFLD_DPLL_P1_MIN_25	    2
+#define MDFLD_DPLL_P1_MAX_25	    10
+#define MDFLD_DPLL_M_MIN_83	    64
+#define MDFLD_DPLL_M_MAX_83	    64
+#define MDFLD_DPLL_P1_MIN_83	    2
+#define MDFLD_DPLL_P1_MAX_83	    2
+#define MDFLD_DPLL_M_MIN_100	    64
+#define MDFLD_DPLL_M_MAX_100	    64
+#define MDFLD_DPLL_P1_MIN_100	    2
+#define MDFLD_DPLL_P1_MAX_100	    2
+#define MDFLD_DSIPLL_M_MIN_19	    131
+#define MDFLD_DSIPLL_M_MAX_19	    175
+#define MDFLD_DSIPLL_P1_MIN_19	    3
+#define MDFLD_DSIPLL_P1_MAX_19	    8
+#define MDFLD_DSIPLL_M_MIN_25	    97
+#define MDFLD_DSIPLL_M_MAX_25	    140
+#define MDFLD_DSIPLL_P1_MIN_25	    3
+#define MDFLD_DSIPLL_P1_MAX_25	    9
+#define MDFLD_DSIPLL_M_MIN_83	    33
+#define MDFLD_DSIPLL_M_MAX_83	    92
+#define MDFLD_DSIPLL_P1_MIN_83	    2
+#define MDFLD_DSIPLL_P1_MAX_83	    3
+#define MDFLD_DSIPLL_M_MIN_100	    97
+#define MDFLD_DSIPLL_M_MAX_100	    140
+#define MDFLD_DSIPLL_P1_MIN_100	    3
+#define MDFLD_DSIPLL_P1_MAX_100	    9
+
+static const struct mrst_limit_t mdfld_limits[] = {
+	{			/* MDFLD_LIMT_DPLL_19 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DPLL_M_MIN_19, .max = MDFLD_DPLL_M_MAX_19},
+	 .p1 = {.min = MDFLD_DPLL_P1_MIN_19, .max = MDFLD_DPLL_P1_MAX_19},
+	 },
+	{			/* MDFLD_LIMT_DPLL_25 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DPLL_M_MIN_25, .max = MDFLD_DPLL_M_MAX_25},
+	 .p1 = {.min = MDFLD_DPLL_P1_MIN_25, .max = MDFLD_DPLL_P1_MAX_25},
+	 },
+	{			/* MDFLD_LIMT_DPLL_83 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DPLL_M_MIN_83, .max = MDFLD_DPLL_M_MAX_83},
+	 .p1 = {.min = MDFLD_DPLL_P1_MIN_83, .max = MDFLD_DPLL_P1_MAX_83},
+	 },
+	{			/* MDFLD_LIMT_DPLL_100 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DPLL_M_MIN_100, .max = MDFLD_DPLL_M_MAX_100},
+	 .p1 = {.min = MDFLD_DPLL_P1_MIN_100, .max = MDFLD_DPLL_P1_MAX_100},
+	 },
+	{			/* MDFLD_LIMT_DSIPLL_19 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DSIPLL_M_MIN_19, .max = MDFLD_DSIPLL_M_MAX_19},
+	 .p1 = {.min = MDFLD_DSIPLL_P1_MIN_19, .max = MDFLD_DSIPLL_P1_MAX_19},
+	 },
+	{			/* MDFLD_LIMT_DSIPLL_25 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DSIPLL_M_MIN_25, .max = MDFLD_DSIPLL_M_MAX_25},
+	 .p1 = {.min = MDFLD_DSIPLL_P1_MIN_25, .max = MDFLD_DSIPLL_P1_MAX_25},
+	 },
+	{			/* MDFLD_LIMT_DSIPLL_83 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DSIPLL_M_MIN_83, .max = MDFLD_DSIPLL_M_MAX_83},
+	 .p1 = {.min = MDFLD_DSIPLL_P1_MIN_83, .max = MDFLD_DSIPLL_P1_MAX_83},
+	 },
+	{			/* MDFLD_LIMT_DSIPLL_100 */
+	 .dot = {.min = MDFLD_DOT_MIN, .max = MDFLD_DOT_MAX},
+	 .m = {.min = MDFLD_DSIPLL_M_MIN_100, .max = MDFLD_DSIPLL_M_MAX_100},
+	 .p1 = {.min = MDFLD_DSIPLL_P1_MIN_100, .max = MDFLD_DSIPLL_P1_MAX_100},
+	 },
+};
+
+#define MDFLD_M_MIN	    21
+#define MDFLD_M_MAX	    180
+static const u32 mdfld_m_converts[] = {
+/* M configuration table from 9-bit LFSR table */
+	224, 368, 440, 220, 366, 439, 219, 365, 182, 347, /* 21 - 30 */
+	173, 342, 171, 85, 298, 149, 74, 37, 18, 265,   /* 31 - 40 */
+	388, 194, 353, 432, 216, 108, 310, 155, 333, 166, /* 41 - 50 */
+	83, 41, 276, 138, 325, 162, 337, 168, 340, 170, /* 51 - 60 */
+	341, 426, 469, 234, 373, 442, 221, 110, 311, 411, /* 61 - 70 */
+	461, 486, 243, 377, 188, 350, 175, 343, 427, 213, /* 71 - 80 */
+	106, 53, 282, 397, 354, 227, 113, 56, 284, 142, /* 81 - 90 */
+	71, 35, 273, 136, 324, 418, 465, 488, 500, 506, /* 91 - 100 */
+	253, 126, 63, 287, 399, 455, 483, 241, 376, 444, /* 101 - 110 */
+	478, 495, 503, 251, 381, 446, 479, 239, 375, 443, /* 111 - 120 */
+	477, 238, 119, 315, 157, 78, 295, 147, 329, 420, /* 121 - 130 */
+	210, 105, 308, 154, 77, 38, 275, 137, 68, 290, /* 131 - 140 */
+	145, 328, 164, 82, 297, 404, 458, 485, 498, 249, /* 141 - 150 */
+	380, 190, 351, 431, 471, 235, 117, 314, 413, 206, /* 151 - 160 */
+	103, 51, 25, 12, 262, 387, 193, 96, 48, 280, /* 161 - 170 */
+	396, 198, 99, 305, 152, 76, 294, 403, 457, 228, /* 171 - 180 */
+};
+
+static const struct mrst_limit_t *mdfld_limit(struct drm_crtc *crtc)
+{
+	const struct mrst_limit_t *limit = NULL;
+	struct drm_device *dev = crtc->dev;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	if (psb_intel_pipe_has_type(crtc, INTEL_OUTPUT_MIPI)
+	    || psb_intel_pipe_has_type(crtc, INTEL_OUTPUT_MIPI2)) {
+		if ((ksel == KSEL_CRYSTAL_19) || (ksel == KSEL_BYPASS_19))
+			limit = &mdfld_limits[MDFLD_LIMT_DSIPLL_19];
+		else if (ksel == KSEL_BYPASS_25)
+			limit = &mdfld_limits[MDFLD_LIMT_DSIPLL_25];
+		else if ((ksel == KSEL_BYPASS_83_100) &&
+				(dev_priv->core_freq == 166))
+			limit = &mdfld_limits[MDFLD_LIMT_DSIPLL_83];
+		else if ((ksel == KSEL_BYPASS_83_100) &&
+			 (dev_priv->core_freq == 100 ||
+				dev_priv->core_freq == 200))
+			limit = &mdfld_limits[MDFLD_LIMT_DSIPLL_100];
+	} else if (psb_intel_pipe_has_type(crtc, INTEL_OUTPUT_HDMI)) {
+		if ((ksel == KSEL_CRYSTAL_19) || (ksel == KSEL_BYPASS_19))
+			limit = &mdfld_limits[MDFLD_LIMT_DPLL_19];
+		else if (ksel == KSEL_BYPASS_25)
+			limit = &mdfld_limits[MDFLD_LIMT_DPLL_25];
+		else if ((ksel == KSEL_BYPASS_83_100) &&
+				(dev_priv->core_freq == 166))
+			limit = &mdfld_limits[MDFLD_LIMT_DPLL_83];
+		else if ((ksel == KSEL_BYPASS_83_100) &&
+				 (dev_priv->core_freq == 100 ||
+				 dev_priv->core_freq == 200))
+			limit = &mdfld_limits[MDFLD_LIMT_DPLL_100];
+	} else {
+		limit = NULL;
+		dev_dbg(dev->dev, "mdfld_limit Wrong display type.\n");
+	}
+
+	return limit;
+}
+
+/** Derive the pixel clock for the given refclk and divisors for 8xx chips. */
+static void mdfld_clock(int refclk, struct mrst_clock_t *clock)
+{
+	clock->dot = (refclk * clock->m) / clock->p1;
+}
+
+/**
+ * Returns a set of divisors for the desired target clock with the given refclk,
+ * or FALSE.  Divisor values are the actual divisors for
+ */
+static bool
+mdfldFindBestPLL(struct drm_crtc *crtc, int target, int refclk,
+		struct mrst_clock_t *best_clock)
+{
+	struct mrst_clock_t clock;
+	const struct mrst_limit_t *limit = mdfld_limit(crtc);
+	int err = target;
+
+	memset(best_clock, 0, sizeof(*best_clock));
+
+	for (clock.m = limit->m.min; clock.m <= limit->m.max; clock.m++) {
+		for (clock.p1 = limit->p1.min; clock.p1 <= limit->p1.max;
+		     clock.p1++) {
+			int this_err;
+
+			mdfld_clock(refclk, &clock);
+
+			this_err = abs(clock.dot - target);
+			if (this_err < err) {
+				*best_clock = clock;
+				err = this_err;
+			}
+		}
+	}
+	return err != target;
+}
+
+static int mdfld_crtc_mode_set(struct drm_crtc *crtc,
+			      struct drm_display_mode *mode,
+			      struct drm_display_mode *adjusted_mode,
+			      int x, int y,
+			      struct drm_framebuffer *old_fb)
+{
+	struct drm_device *dev = crtc->dev;
+	struct psb_intel_crtc *psb_intel_crtc = to_psb_intel_crtc(crtc);
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	int pipe = psb_intel_crtc->pipe;
+	int fp_reg = MRST_FPA0;
+	int dpll_reg = MRST_DPLL_A;
+	int dspcntr_reg = DSPACNTR;
+	int pipeconf_reg = PIPEACONF;
+	int htot_reg = HTOTAL_A;
+	int hblank_reg = HBLANK_A;
+	int hsync_reg = HSYNC_A;
+	int vtot_reg = VTOTAL_A;
+	int vblank_reg = VBLANK_A;
+	int vsync_reg = VSYNC_A;
+	int dspsize_reg = DSPASIZE;
+	int dsppos_reg = DSPAPOS;
+	int pipesrc_reg = PIPEASRC;
+	u32 *pipeconf = &dev_priv->pipeconf[pipe];
+	u32 *dspcntr = &dev_priv->dspcntr[pipe];
+	int refclk = 0;
+	int clk_n = 0, clk_p2 = 0, clk_byte = 1, clk = 0, m_conv = 0,
+								clk_tmp = 0;
+	struct mrst_clock_t clock;
+	bool ok;
+	u32 dpll = 0, fp = 0;
+	bool is_crt = false, is_lvds = false, is_tv = false;
+	bool is_mipi = false, is_mipi2 = false, is_hdmi = false;
+	struct drm_mode_config *mode_config = &dev->mode_config;
+	struct psb_intel_encoder *psb_intel_encoder = NULL;
+	uint64_t scalingType = DRM_MODE_SCALE_FULLSCREEN;
+	struct drm_encoder *encoder;
+	struct drm_connector *connector;
+	int timeout = 0;
+	int ret;
+
+	dev_dbg(dev->dev, "pipe = 0x%x\n", pipe);
+
+#if 0
+	if (pipe == 1) {
+		if (!gma_power_begin(dev, true))
+			return 0;
+		android_hdmi_crtc_mode_set(crtc, mode, adjusted_mode,
+			x, y, old_fb);
+		goto mrst_crtc_mode_set_exit;
+	}
+#endif
+
+	switch (pipe) {
+	case 0:
+		break;
+	case 1:
+		fp_reg = FPB0;
+		dpll_reg = DPLL_B;
+		dspcntr_reg = DSPBCNTR;
+		pipeconf_reg = PIPEBCONF;
+		htot_reg = HTOTAL_B;
+		hblank_reg = HBLANK_B;
+		hsync_reg = HSYNC_B;
+		vtot_reg = VTOTAL_B;
+		vblank_reg = VBLANK_B;
+		vsync_reg = VSYNC_B;
+		dspsize_reg = DSPBSIZE;
+		dsppos_reg = DSPBPOS;
+		pipesrc_reg = PIPEBSRC;
+		fp_reg = MDFLD_DPLL_DIV0;
+		dpll_reg = MDFLD_DPLL_B;
+		break;
+	case 2:
+		dpll_reg = MRST_DPLL_A;
+		dspcntr_reg = DSPCCNTR;
+		pipeconf_reg = PIPECCONF;
+		htot_reg = HTOTAL_C;
+		hblank_reg = HBLANK_C;
+		hsync_reg = HSYNC_C;
+		vtot_reg = VTOTAL_C;
+		vblank_reg = VBLANK_C;
+		vsync_reg = VSYNC_C;
+		dspsize_reg = DSPCSIZE;
+		dsppos_reg = DSPCPOS;
+		pipesrc_reg = PIPECSRC;
+		break;
+	default:
+		DRM_ERROR("Illegal Pipe Number.\n");
+		return 0;
+	}
+
+	ret = check_fb(crtc->fb);
+	if (ret)
+		return ret;
+
+	dev_dbg(dev->dev, "adjusted_hdisplay = %d\n",
+		 adjusted_mode->hdisplay);
+	dev_dbg(dev->dev, "adjusted_vdisplay = %d\n",
+		 adjusted_mode->vdisplay);
+	dev_dbg(dev->dev, "adjusted_hsync_start = %d\n",
+		 adjusted_mode->hsync_start);
+	dev_dbg(dev->dev, "adjusted_hsync_end = %d\n",
+		 adjusted_mode->hsync_end);
+	dev_dbg(dev->dev, "adjusted_htotal = %d\n",
+		 adjusted_mode->htotal);
+	dev_dbg(dev->dev, "adjusted_vsync_start = %d\n",
+		 adjusted_mode->vsync_start);
+	dev_dbg(dev->dev, "adjusted_vsync_end = %d\n",
+		 adjusted_mode->vsync_end);
+	dev_dbg(dev->dev, "adjusted_vtotal = %d\n",
+		 adjusted_mode->vtotal);
+	dev_dbg(dev->dev, "adjusted_clock = %d\n",
+		 adjusted_mode->clock);
+	dev_dbg(dev->dev, "hdisplay = %d\n",
+		 mode->hdisplay);
+	dev_dbg(dev->dev, "vdisplay = %d\n",
+		 mode->vdisplay);
+
+	if (!gma_power_begin(dev, true))
+		return 0;
+
+	memcpy(&psb_intel_crtc->saved_mode, mode,
+					sizeof(struct drm_display_mode));
+	memcpy(&psb_intel_crtc->saved_adjusted_mode, adjusted_mode,
+					sizeof(struct drm_display_mode));
+
+	list_for_each_entry(connector, &mode_config->connector_list, head) {
+		if (!connector)
+			continue;
+
+		encoder = connector->encoder;
+
+		if (!encoder)
+			continue;
+
+		if (encoder->crtc != crtc)
+			continue;
+
+		psb_intel_encoder = psb_intel_attached_encoder(connector);
+
+		switch (psb_intel_encoder->type) {
+		case INTEL_OUTPUT_LVDS:
+			is_lvds = true;
+			break;
+		case INTEL_OUTPUT_TVOUT:
+			is_tv = true;
+			break;
+		case INTEL_OUTPUT_ANALOG:
+			is_crt = true;
+			break;
+		case INTEL_OUTPUT_MIPI:
+			is_mipi = true;
+			break;
+		case INTEL_OUTPUT_MIPI2:
+			is_mipi2 = true;
+			break;
+		case INTEL_OUTPUT_HDMI:
+			is_hdmi = true;
+			break;
+		}
+	}
+
+	/* Disable the VGA plane that we never use */
+	REG_WRITE(VGACNTRL, VGA_DISP_DISABLE);
+
+	/* Disable the panel fitter if it was on our pipe */
+	if (psb_intel_panel_fitter_pipe(dev) == pipe)
+		REG_WRITE(PFIT_CONTROL, 0);
+
+	/* pipesrc and dspsize control the size that is scaled from,
+	 * which should always be the user's requested size.
+	 */
+	if (pipe == 1) {
+		/* FIXME: To make HDMI display with 864x480 (TPO), 480x864
+		 * (PYR) or 480x854 (TMD), set the sprite width/height and
+		 * souce image size registers with the adjusted mode for
+		 * pipe B.
+		 */
+
+		/*
+		 * The defined sprite rectangle must always be completely
+		 * contained within the displayable area of the screen image
+		 * (frame buffer).
+		 */
+		REG_WRITE(dspsize_reg, ((min(mode->crtc_vdisplay, adjusted_mode->crtc_vdisplay) - 1) << 16)
+				| (min(mode->crtc_hdisplay, adjusted_mode->crtc_hdisplay) - 1));
+		/* Set the CRTC with encoder mode. */
+		REG_WRITE(pipesrc_reg, ((mode->crtc_hdisplay - 1) << 16)
+				 | (mode->crtc_vdisplay - 1));
+	} else {
+		REG_WRITE(dspsize_reg,
+				((mode->crtc_vdisplay - 1) << 16) |
+						(mode->crtc_hdisplay - 1));
+		REG_WRITE(pipesrc_reg,
+				((mode->crtc_hdisplay - 1) << 16) |
+						(mode->crtc_vdisplay - 1));
+	}
+
+	REG_WRITE(dsppos_reg, 0);
+
+	if (psb_intel_encoder)
+		drm_connector_property_get_value(connector,
+			dev->mode_config.scaling_mode_property, &scalingType);
+
+	if (scalingType == DRM_MODE_SCALE_NO_SCALE) {
+		/* Medfield doesn't have register support for centering so we
+		 * need to mess with the h/vblank and h/vsync start and ends
+		 * to get centering
+		 */
+		int offsetX = 0, offsetY = 0;
+
+		offsetX = (adjusted_mode->crtc_hdisplay -
+					mode->crtc_hdisplay) / 2;
+		offsetY = (adjusted_mode->crtc_vdisplay -
+					mode->crtc_vdisplay) / 2;
+
+		REG_WRITE(htot_reg, (mode->crtc_hdisplay - 1) |
+			((adjusted_mode->crtc_htotal - 1) << 16));
+		REG_WRITE(vtot_reg, (mode->crtc_vdisplay - 1) |
+			((adjusted_mode->crtc_vtotal - 1) << 16));
+		REG_WRITE(hblank_reg, (adjusted_mode->crtc_hblank_start -
+								offsetX - 1) |
+			((adjusted_mode->crtc_hblank_end - offsetX - 1) << 16));
+		REG_WRITE(hsync_reg, (adjusted_mode->crtc_hsync_start -
+								offsetX - 1) |
+			((adjusted_mode->crtc_hsync_end - offsetX - 1) << 16));
+		REG_WRITE(vblank_reg, (adjusted_mode->crtc_vblank_start -
+								offsetY - 1) |
+			((adjusted_mode->crtc_vblank_end - offsetY - 1) << 16));
+		REG_WRITE(vsync_reg, (adjusted_mode->crtc_vsync_start -
+								offsetY - 1) |
+			((adjusted_mode->crtc_vsync_end - offsetY - 1) << 16));
+	} else {
+		REG_WRITE(htot_reg, (adjusted_mode->crtc_hdisplay - 1) |
+			((adjusted_mode->crtc_htotal - 1) << 16));
+		REG_WRITE(vtot_reg, (adjusted_mode->crtc_vdisplay - 1) |
+			((adjusted_mode->crtc_vtotal - 1) << 16));
+		REG_WRITE(hblank_reg, (adjusted_mode->crtc_hblank_start - 1) |
+			((adjusted_mode->crtc_hblank_end - 1) << 16));
+		REG_WRITE(hsync_reg, (adjusted_mode->crtc_hsync_start - 1) |
+			((adjusted_mode->crtc_hsync_end - 1) << 16));
+		REG_WRITE(vblank_reg, (adjusted_mode->crtc_vblank_start - 1) |
+			((adjusted_mode->crtc_vblank_end - 1) << 16));
+		REG_WRITE(vsync_reg, (adjusted_mode->crtc_vsync_start - 1) |
+			((adjusted_mode->crtc_vsync_end - 1) << 16));
+	}
+
+	/* Flush the plane changes */
+	{
+		struct drm_crtc_helper_funcs *crtc_funcs =
+		    crtc->helper_private;
+		crtc_funcs->mode_set_base(crtc, x, y, old_fb);
+	}
+
+	/* setup pipeconf */
+	*pipeconf = PIPEACONF_ENABLE; /* FIXME_JLIU7 REG_READ(pipeconf_reg); */
+
+	/* Set up the display plane register */
+	*dspcntr = REG_READ(dspcntr_reg);
+	*dspcntr |= pipe << DISPPLANE_SEL_PIPE_POS;
+	*dspcntr |= DISPLAY_PLANE_ENABLE;
+
+	if (is_mipi2)
+		goto mrst_crtc_mode_set_exit;
+	clk = adjusted_mode->clock;
+
+	if (is_hdmi) {
+		if ((ksel == KSEL_CRYSTAL_19) || (ksel == KSEL_BYPASS_19)) {
+			refclk = 19200;
+
+			if (is_mipi || is_mipi2)
+				clk_n = 1, clk_p2 = 8;
+			else if (is_hdmi)
+				clk_n = 1, clk_p2 = 10;
+		} else if (ksel == KSEL_BYPASS_25) {
+			refclk = 25000;
+
+			if (is_mipi || is_mipi2)
+				clk_n = 1, clk_p2 = 8;
+			else if (is_hdmi)
+				clk_n = 1, clk_p2 = 10;
+		} else if ((ksel == KSEL_BYPASS_83_100) &&
+					dev_priv->core_freq == 166) {
+			refclk = 83000;
+
+			if (is_mipi || is_mipi2)
+				clk_n = 4, clk_p2 = 8;
+			else if (is_hdmi)
+				clk_n = 4, clk_p2 = 10;
+		} else if ((ksel == KSEL_BYPASS_83_100) &&
+					(dev_priv->core_freq == 100 ||
+					dev_priv->core_freq == 200)) {
+			refclk = 100000;
+			if (is_mipi || is_mipi2)
+				clk_n = 4, clk_p2 = 8;
+			else if (is_hdmi)
+				clk_n = 4, clk_p2 = 10;
+		}
+
+		if (is_mipi)
+			clk_byte = dev_priv->bpp / 8;
+		else if (is_mipi2)
+			clk_byte = dev_priv->bpp2 / 8;
+
+		clk_tmp = clk * clk_n * clk_p2 * clk_byte;
+
+		dev_dbg(dev->dev, "clk = %d, clk_n = %d, clk_p2 = %d.\n",
+					clk, clk_n, clk_p2);
+		dev_dbg(dev->dev, "adjusted_mode->clock = %d, clk_tmp = %d.\n",
+					adjusted_mode->clock, clk_tmp);
+
+		ok = mdfldFindBestPLL(crtc, clk_tmp, refclk, &clock);
+
+		if (!ok) {
+			DRM_ERROR
+			    ("mdfldFindBestPLL fail in mdfld_crtc_mode_set.\n");
+		} else {
+			m_conv = mdfld_m_converts[(clock.m - MDFLD_M_MIN)];
+
+			dev_dbg(dev->dev, "dot clock = %d,"
+				 "m = %d, p1 = %d, m_conv = %d.\n",
+					clock.dot, clock.m,
+					clock.p1, m_conv);
+		}
+
+		dpll = REG_READ(dpll_reg);
+
+		if (dpll & DPLL_VCO_ENABLE) {
+			dpll &= ~DPLL_VCO_ENABLE;
+			REG_WRITE(dpll_reg, dpll);
+			REG_READ(dpll_reg);
+
+			/* FIXME jliu7 check the DPLL lock bit PIPEACONF[29] */
+			/* FIXME_MDFLD PO - change 500 to 1 after PO */
+			udelay(500);
+
+			/* reset M1, N1 & P1 */
+			REG_WRITE(fp_reg, 0);
+			dpll &= ~MDFLD_P1_MASK;
+			REG_WRITE(dpll_reg, dpll);
+			/* FIXME_MDFLD PO - change 500 to 1 after PO */
+			udelay(500);
+		}
+
+		/* When ungating power of DPLL, needs to wait 0.5us before
+		 * enable the VCO */
+		if (dpll & MDFLD_PWR_GATE_EN) {
+			dpll &= ~MDFLD_PWR_GATE_EN;
+			REG_WRITE(dpll_reg, dpll);
+			/* FIXME_MDFLD PO - change 500 to 1 after PO */
+			udelay(500);
+		}
+		dpll = 0;
+
+#if 0 /* FIXME revisit later */
+		if (ksel == KSEL_CRYSTAL_19 || ksel == KSEL_BYPASS_19 ||
+						ksel == KSEL_BYPASS_25)
+			dpll &= ~MDFLD_INPUT_REF_SEL;
+		else if (ksel == KSEL_BYPASS_83_100)
+			dpll |= MDFLD_INPUT_REF_SEL;
+#endif /* FIXME revisit later */
+
+		if (is_hdmi)
+			dpll |= MDFLD_VCO_SEL;
+
+		fp = (clk_n / 2) << 16;
+		fp |= m_conv;
+
+		/* compute bitmask from p1 value */
+		dpll |= (1 << (clock.p1 - 2)) << 17;
+
+#if 0 /* 1080p30 & 720p */
+		dpll = 0x00050000;
+		fp = 0x000001be;
+#endif
+#if 0 /* 480p */
+		dpll = 0x02010000;
+		fp = 0x000000d2;
+#endif
+	} else {
+#if 0 /*DBI_TPO_480x864*/
+		dpll = 0x00020000;
+		fp = 0x00000156;
+#endif /* DBI_TPO_480x864 */ /* get from spec. */
+
+		dpll = 0x00800000;
+		fp = 0x000000c1;
+	}
+
+	REG_WRITE(fp_reg, fp);
+	REG_WRITE(dpll_reg, dpll);
+	/* FIXME_MDFLD PO - change 500 to 1 after PO */
+	udelay(500);
+
+	dpll |= DPLL_VCO_ENABLE;
+	REG_WRITE(dpll_reg, dpll);
+	REG_READ(dpll_reg);
+
+	/* wait for DSI PLL to lock */
+	while (timeout < 20000 &&
+			!(REG_READ(pipeconf_reg) & PIPECONF_DSIPLL_LOCK)) {
+		udelay(150);
+		timeout++;
+	}
+
+	if (is_mipi)
+		goto mrst_crtc_mode_set_exit;
+
+	dev_dbg(dev->dev, "is_mipi = 0x%x\n", is_mipi);
+
+	REG_WRITE(pipeconf_reg, *pipeconf);
+	REG_READ(pipeconf_reg);
+
+	/* Wait for for the pipe enable to take effect. */
+	REG_WRITE(dspcntr_reg, *dspcntr);
+	psb_intel_wait_for_vblank(dev);
+
+mrst_crtc_mode_set_exit:
+
+	gma_power_end(dev);
+
+	return 0;
+}
+
+const struct drm_crtc_helper_funcs mdfld_helper_funcs = {
+	.dpms = mdfld_crtc_dpms,
+	.mode_fixup = psb_intel_crtc_mode_fixup,
+	.mode_set = mdfld_crtc_mode_set,
+	.mode_set_base = mdfld__intel_pipe_set_base,
+	.prepare = psb_intel_crtc_prepare,
+	.commit = psb_intel_crtc_commit,
+};
+
diff --git a/drivers/gpu/drm/gma500/mdfld_output.c b/drivers/gpu/drm/gma500/mdfld_output.c
new file mode 100644
index 00000000000..de0ce076573
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_output.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (c)  2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicensen
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * Thomas Eaton <thomas.g.eaton@intel.com>
+ * Scott Rowe <scott.m.rowe@intel.com>
+*/
+
+#include "mdfld_output.h"
+#include "mdfld_dsi_dpi.h"
+#include "mdfld_dsi_output.h"
+
+#include "tc35876x-dsi-lvds.h"
+
+int mdfld_get_panel_type(struct drm_device *dev, int pipe)
+{
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	return dev_priv->mdfld_panel_id;
+}
+
+static void mdfld_init_panel(struct drm_device *dev, int mipi_pipe,
+								int p_type)
+{
+	switch (p_type) {
+	case TPO_VID:
+		mdfld_dsi_output_init(dev, mipi_pipe, NULL,
+				&mdfld_tpo_vid_funcs);
+		break;
+	case TC35876X:
+		tc35876x_init(dev);
+		mdfld_dsi_output_init(dev, mipi_pipe, NULL,
+				&mdfld_tc35876x_funcs);
+		break;
+	case TMD_VID:
+		mdfld_dsi_output_init(dev, mipi_pipe, NULL,
+				&mdfld_tmd_vid_funcs);
+		break;
+	case HDMI:
+/*		if (dev_priv->mdfld_hdmi_present)
+			mdfld_hdmi_init(dev, &dev_priv->mode_dev); */
+		break;
+	}
+}
+
+
+int mdfld_output_init(struct drm_device *dev)
+{
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	/* FIXME: hardcoded for now */
+	dev_priv->mdfld_panel_id = TC35876X;
+	/* MIPI panel 1 */
+	mdfld_init_panel(dev, 0, dev_priv->mdfld_panel_id);
+	/* HDMI panel */
+	mdfld_init_panel(dev, 1, HDMI);
+	return 0;
+}
+
diff --git a/drivers/gpu/drm/gma500/mdfld_output.h b/drivers/gpu/drm/gma500/mdfld_output.h
new file mode 100644
index 00000000000..ab2b27c0f03
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_output.h
@@ -0,0 +1,77 @@
+/*
+ * Copyright (c)  2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicensen
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * Thomas Eaton <thomas.g.eaton@intel.com>
+ * Scott Rowe <scott.m.rowe@intel.com>
+*/
+
+#ifndef MDFLD_OUTPUT_H
+#define MDFLD_OUTPUT_H
+
+#include "psb_drv.h"
+
+#define TPO_PANEL_WIDTH		84
+#define TPO_PANEL_HEIGHT	46
+#define TMD_PANEL_WIDTH		39
+#define TMD_PANEL_HEIGHT	71
+
+struct mdfld_dsi_config;
+
+enum panel_type {
+	TPO_VID,
+	TMD_VID,
+	HDMI,
+	TC35876X,
+};
+
+struct panel_info {
+	u32 width_mm;
+	u32 height_mm;
+	/* Other info */
+};
+
+struct panel_funcs {
+	const struct drm_encoder_funcs *encoder_funcs;
+	const struct drm_encoder_helper_funcs *encoder_helper_funcs;
+	struct drm_display_mode * (*get_config_mode)(struct drm_device *);
+	int (*get_panel_info)(struct drm_device *, int, struct panel_info *);
+	int (*reset)(int pipe);
+	void (*drv_ic_init)(struct mdfld_dsi_config *dsi_config, int pipe);
+};
+
+int mdfld_output_init(struct drm_device *dev);
+
+struct backlight_device *mdfld_get_backlight_device(void);
+int mdfld_set_brightness(struct backlight_device *bd);
+
+int mdfld_get_panel_type(struct drm_device *dev, int pipe);
+
+extern const struct drm_crtc_helper_funcs mdfld_helper_funcs;
+
+extern const struct panel_funcs mdfld_tmd_vid_funcs;
+extern const struct panel_funcs mdfld_tpo_vid_funcs;
+
+extern void mdfld_disable_crtc(struct drm_device *dev, int pipe);
+extern void mdfldWaitForPipeEnable(struct drm_device *dev, int pipe);
+extern void mdfldWaitForPipeDisable(struct drm_device *dev, int pipe);
+#endif
diff --git a/drivers/gpu/drm/gma500/mdfld_tmd_vid.c b/drivers/gpu/drm/gma500/mdfld_tmd_vid.c
new file mode 100644
index 00000000000..dc0c6c3d3d2
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_tmd_vid.c
@@ -0,0 +1,201 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * Jim Liu <jim.liu@intel.com>
+ * Jackie Li<yaodong.li@intel.com>
+ * Gideon Eaton <eaton.
+ * Scott Rowe <scott.m.rowe@intel.com>
+ */
+
+#include "mdfld_dsi_dpi.h"
+#include "mdfld_dsi_pkg_sender.h"
+
+static struct drm_display_mode *tmd_vid_get_config_mode(struct drm_device *dev)
+{
+	struct drm_display_mode *mode;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	struct oaktrail_timing_info *ti = &dev_priv->gct_data.DTD;
+	bool use_gct = false; /*Disable GCT for now*/
+
+	mode = kzalloc(sizeof(*mode), GFP_KERNEL);
+	if (!mode)
+		return NULL;
+
+	if (use_gct) {
+		mode->hdisplay = (ti->hactive_hi << 8) | ti->hactive_lo;
+		mode->vdisplay = (ti->vactive_hi << 8) | ti->vactive_lo;
+		mode->hsync_start = mode->hdisplay + \
+				((ti->hsync_offset_hi << 8) | \
+				ti->hsync_offset_lo);
+		mode->hsync_end = mode->hsync_start + \
+				((ti->hsync_pulse_width_hi << 8) | \
+				ti->hsync_pulse_width_lo);
+		mode->htotal = mode->hdisplay + ((ti->hblank_hi << 8) | \
+								ti->hblank_lo);
+		mode->vsync_start = \
+			mode->vdisplay + ((ti->vsync_offset_hi << 8) | \
+						ti->vsync_offset_lo);
+		mode->vsync_end = \
+			mode->vsync_start + ((ti->vsync_pulse_width_hi << 8) | \
+						ti->vsync_pulse_width_lo);
+		mode->vtotal = mode->vdisplay + \
+				((ti->vblank_hi << 8) | ti->vblank_lo);
+		mode->clock = ti->pixel_clock * 10;
+
+		dev_dbg(dev->dev, "hdisplay is %d\n", mode->hdisplay);
+		dev_dbg(dev->dev, "vdisplay is %d\n", mode->vdisplay);
+		dev_dbg(dev->dev, "HSS is %d\n", mode->hsync_start);
+		dev_dbg(dev->dev, "HSE is %d\n", mode->hsync_end);
+		dev_dbg(dev->dev, "htotal is %d\n", mode->htotal);
+		dev_dbg(dev->dev, "VSS is %d\n", mode->vsync_start);
+		dev_dbg(dev->dev, "VSE is %d\n", mode->vsync_end);
+		dev_dbg(dev->dev, "vtotal is %d\n", mode->vtotal);
+		dev_dbg(dev->dev, "clock is %d\n", mode->clock);
+	} else {
+		mode->hdisplay = 480;
+		mode->vdisplay = 854;
+		mode->hsync_start = 487;
+		mode->hsync_end = 490;
+		mode->htotal = 499;
+		mode->vsync_start = 861;
+		mode->vsync_end = 865;
+		mode->vtotal = 873;
+		mode->clock = 33264;
+	}
+
+	drm_mode_set_name(mode);
+	drm_mode_set_crtcinfo(mode, 0);
+
+	mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+	return mode;
+}
+
+static int tmd_vid_get_panel_info(struct drm_device *dev,
+				int pipe,
+				struct panel_info *pi)
+{
+	if (!dev || !pi)
+		return -EINVAL;
+
+	pi->width_mm = TMD_PANEL_WIDTH;
+	pi->height_mm = TMD_PANEL_HEIGHT;
+
+	return 0;
+}
+
+/* ************************************************************************* *\
+ * FUNCTION: mdfld_init_TMD_MIPI
+ *
+ * DESCRIPTION:  This function is called only by mrst_dsi_mode_set and
+ *               restore_display_registers.  since this function does not
+ *               acquire the mutex, it is important that the calling function
+ *               does!
+\* ************************************************************************* */
+
+/* FIXME: make the below data u8 instead of u32; note byte order! */
+static u32 tmd_cmd_mcap_off[] = {0x000000b2};
+static u32 tmd_cmd_enable_lane_switch[] = {0x000101ef};
+static u32 tmd_cmd_set_lane_num[] = {0x006360ef};
+static u32 tmd_cmd_pushing_clock0[] = {0x00cc2fef};
+static u32 tmd_cmd_pushing_clock1[] = {0x00dd6eef};
+static u32 tmd_cmd_set_mode[] = {0x000000b3};
+static u32 tmd_cmd_set_sync_pulse_mode[] = {0x000961ef};
+static u32 tmd_cmd_set_column[] = {0x0100002a, 0x000000df};
+static u32 tmd_cmd_set_page[] = {0x0300002b, 0x00000055};
+static u32 tmd_cmd_set_video_mode[] = {0x00000153};
+/*no auto_bl,need add in furture*/
+static u32 tmd_cmd_enable_backlight[] = {0x00005ab4};
+static u32 tmd_cmd_set_backlight_dimming[] = {0x00000ebd};
+
+static void mdfld_dsi_tmd_drv_ic_init(struct mdfld_dsi_config *dsi_config,
+				      int pipe)
+{
+	struct mdfld_dsi_pkg_sender *sender
+			= mdfld_dsi_get_pkg_sender(dsi_config);
+
+	DRM_INFO("Enter mdfld init TMD MIPI display.\n");
+
+	if (!sender) {
+		DRM_ERROR("Cannot get sender\n");
+		return;
+	}
+
+	if (dsi_config->dvr_ic_inited)
+		return;
+
+	msleep(3);
+
+	/* FIXME: make the below data u8 instead of u32; note byte order! */
+
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_mcap_off,
+				sizeof(tmd_cmd_mcap_off), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_enable_lane_switch,
+				sizeof(tmd_cmd_enable_lane_switch), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_set_lane_num,
+				sizeof(tmd_cmd_set_lane_num), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_pushing_clock0,
+				sizeof(tmd_cmd_pushing_clock0), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_pushing_clock1,
+				sizeof(tmd_cmd_pushing_clock1), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_set_mode,
+				sizeof(tmd_cmd_set_mode), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_set_sync_pulse_mode,
+				sizeof(tmd_cmd_set_sync_pulse_mode), false);
+	mdfld_dsi_send_mcs_long(sender, (u8 *) tmd_cmd_set_column,
+				sizeof(tmd_cmd_set_column), false);
+	mdfld_dsi_send_mcs_long(sender, (u8 *) tmd_cmd_set_page,
+				sizeof(tmd_cmd_set_page), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_set_video_mode,
+				sizeof(tmd_cmd_set_video_mode), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_enable_backlight,
+				sizeof(tmd_cmd_enable_backlight), false);
+	mdfld_dsi_send_gen_long(sender, (u8 *) tmd_cmd_set_backlight_dimming,
+				sizeof(tmd_cmd_set_backlight_dimming), false);
+
+	dsi_config->dvr_ic_inited = 1;
+}
+
+/*TPO DPI encoder helper funcs*/
+static const struct drm_encoder_helper_funcs
+				mdfld_tpo_dpi_encoder_helper_funcs = {
+	.dpms = mdfld_dsi_dpi_dpms,
+	.mode_fixup = mdfld_dsi_dpi_mode_fixup,
+	.prepare = mdfld_dsi_dpi_prepare,
+	.mode_set = mdfld_dsi_dpi_mode_set,
+	.commit = mdfld_dsi_dpi_commit,
+};
+
+/*TPO DPI encoder funcs*/
+static const struct drm_encoder_funcs mdfld_tpo_dpi_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+const struct panel_funcs mdfld_tmd_vid_funcs = {
+	.encoder_funcs = &mdfld_tpo_dpi_encoder_funcs,
+	.encoder_helper_funcs = &mdfld_tpo_dpi_encoder_helper_funcs,
+	.get_config_mode = &tmd_vid_get_config_mode,
+	.get_panel_info = tmd_vid_get_panel_info,
+	.reset = mdfld_dsi_panel_reset,
+	.drv_ic_init = mdfld_dsi_tmd_drv_ic_init,
+};
diff --git a/drivers/gpu/drm/gma500/mdfld_tpo_vid.c b/drivers/gpu/drm/gma500/mdfld_tpo_vid.c
new file mode 100644
index 00000000000..d8d4170725b
--- /dev/null
+++ b/drivers/gpu/drm/gma500/mdfld_tpo_vid.c
@@ -0,0 +1,124 @@
+/*
+ * Copyright © 2010 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ * Authors:
+ * jim liu <jim.liu@intel.com>
+ * Jackie Li<yaodong.li@intel.com>
+ */
+
+#include "mdfld_dsi_dpi.h"
+
+static struct drm_display_mode *tpo_vid_get_config_mode(struct drm_device *dev)
+{
+	struct drm_display_mode *mode;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+	struct oaktrail_timing_info *ti = &dev_priv->gct_data.DTD;
+	bool use_gct = false;
+
+	mode = kzalloc(sizeof(*mode), GFP_KERNEL);
+	if (!mode)
+		return NULL;
+
+	if (use_gct) {
+		mode->hdisplay = (ti->hactive_hi << 8) | ti->hactive_lo;
+		mode->vdisplay = (ti->vactive_hi << 8) | ti->vactive_lo;
+		mode->hsync_start = mode->hdisplay +
+				((ti->hsync_offset_hi << 8) |
+				ti->hsync_offset_lo);
+		mode->hsync_end = mode->hsync_start +
+				((ti->hsync_pulse_width_hi << 8) |
+				ti->hsync_pulse_width_lo);
+		mode->htotal = mode->hdisplay + ((ti->hblank_hi << 8) |
+								ti->hblank_lo);
+		mode->vsync_start =
+			mode->vdisplay + ((ti->vsync_offset_hi << 8) |
+						ti->vsync_offset_lo);
+		mode->vsync_end =
+			mode->vsync_start + ((ti->vsync_pulse_width_hi << 8) |
+						ti->vsync_pulse_width_lo);
+		mode->vtotal = mode->vdisplay +
+				((ti->vblank_hi << 8) | ti->vblank_lo);
+		mode->clock = ti->pixel_clock * 10;
+
+		dev_dbg(dev->dev, "hdisplay is %d\n", mode->hdisplay);
+		dev_dbg(dev->dev, "vdisplay is %d\n", mode->vdisplay);
+		dev_dbg(dev->dev, "HSS is %d\n", mode->hsync_start);
+		dev_dbg(dev->dev, "HSE is %d\n", mode->hsync_end);
+		dev_dbg(dev->dev, "htotal is %d\n", mode->htotal);
+		dev_dbg(dev->dev, "VSS is %d\n", mode->vsync_start);
+		dev_dbg(dev->dev, "VSE is %d\n", mode->vsync_end);
+		dev_dbg(dev->dev, "vtotal is %d\n", mode->vtotal);
+		dev_dbg(dev->dev, "clock is %d\n", mode->clock);
+	} else {
+		mode->hdisplay = 864;
+		mode->vdisplay = 480;
+		mode->hsync_start = 873;
+		mode->hsync_end = 876;
+		mode->htotal = 887;
+		mode->vsync_start = 487;
+		mode->vsync_end = 490;
+		mode->vtotal = 499;
+		mode->clock = 33264;
+	}
+
+	drm_mode_set_name(mode);
+	drm_mode_set_crtcinfo(mode, 0);
+
+	mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+	return mode;
+}
+
+static int tpo_vid_get_panel_info(struct drm_device *dev,
+				int pipe,
+				struct panel_info *pi)
+{
+	if (!dev || !pi)
+		return -EINVAL;
+
+	pi->width_mm = TPO_PANEL_WIDTH;
+	pi->height_mm = TPO_PANEL_HEIGHT;
+
+	return 0;
+}
+
+/*TPO DPI encoder helper funcs*/
+static const struct drm_encoder_helper_funcs
+				mdfld_tpo_dpi_encoder_helper_funcs = {
+	.dpms = mdfld_dsi_dpi_dpms,
+	.mode_fixup = mdfld_dsi_dpi_mode_fixup,
+	.prepare = mdfld_dsi_dpi_prepare,
+	.mode_set = mdfld_dsi_dpi_mode_set,
+	.commit = mdfld_dsi_dpi_commit,
+};
+
+/*TPO DPI encoder funcs*/
+static const struct drm_encoder_funcs mdfld_tpo_dpi_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+const struct panel_funcs mdfld_tpo_vid_funcs = {
+	.encoder_funcs = &mdfld_tpo_dpi_encoder_funcs,
+	.encoder_helper_funcs = &mdfld_tpo_dpi_encoder_helper_funcs,
+	.get_config_mode = &tpo_vid_get_config_mode,
+	.get_panel_info = tpo_vid_get_panel_info,
+};
diff --git a/drivers/gpu/drm/gma500/psb_drv.c b/drivers/gpu/drm/gma500/psb_drv.c
index 1f57aac2cf8..fc3293049fe 100644
--- a/drivers/gpu/drm/gma500/psb_drv.c
+++ b/drivers/gpu/drm/gma500/psb_drv.c
@@ -60,6 +60,16 @@ static DEFINE_PCI_DEVICE_TABLE(pciidlist) = {
 	/* Atom E620 */
 	{ 0x8086, 0x4108, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &oaktrail_chip_ops},
 #endif
+#if defined(CONFIG_DRM_MEDFIELD)
+	{0x8086, 0x0130, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+	{0x8086, 0x0131, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+	{0x8086, 0x0132, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+	{0x8086, 0x0133, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+	{0x8086, 0x0134, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+	{0x8086, 0x0135, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+	{0x8086, 0x0136, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+	{0x8086, 0x0137, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &mdfld_chip_ops},
+#endif
 #if defined(CONFIG_DRM_GMA3600)
 	{ 0x8086, 0x0be0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &cdv_chip_ops},
 	{ 0x8086, 0x0be1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (long) &cdv_chip_ops},
diff --git a/drivers/gpu/drm/gma500/psb_drv.h b/drivers/gpu/drm/gma500/psb_drv.h
index 3c0bf7be273..af1c9975200 100644
--- a/drivers/gpu/drm/gma500/psb_drv.h
+++ b/drivers/gpu/drm/gma500/psb_drv.h
@@ -389,11 +389,79 @@ struct psb_state {
 	uint32_t savePWM_CONTROL_LOGIC;
 };
 
+struct medfield_state {
+	uint32_t saveDPLL_A;
+	uint32_t saveFPA0;
+	uint32_t savePIPEACONF;
+	uint32_t saveHTOTAL_A;
+	uint32_t saveHBLANK_A;
+	uint32_t saveHSYNC_A;
+	uint32_t saveVTOTAL_A;
+	uint32_t saveVBLANK_A;
+	uint32_t saveVSYNC_A;
+	uint32_t savePIPEASRC;
+	uint32_t saveDSPASTRIDE;
+	uint32_t saveDSPALINOFF;
+	uint32_t saveDSPATILEOFF;
+	uint32_t saveDSPASIZE;
+	uint32_t saveDSPAPOS;
+	uint32_t saveDSPASURF;
+	uint32_t saveDSPACNTR;
+	uint32_t saveDSPASTATUS;
+	uint32_t save_palette_a[256];
+	uint32_t saveMIPI;
+
+	uint32_t saveDPLL_B;
+	uint32_t saveFPB0;
+	uint32_t savePIPEBCONF;
+	uint32_t saveHTOTAL_B;
+	uint32_t saveHBLANK_B;
+	uint32_t saveHSYNC_B;
+	uint32_t saveVTOTAL_B;
+	uint32_t saveVBLANK_B;
+	uint32_t saveVSYNC_B;
+	uint32_t savePIPEBSRC;
+	uint32_t saveDSPBSTRIDE;
+	uint32_t saveDSPBLINOFF;
+	uint32_t saveDSPBTILEOFF;
+	uint32_t saveDSPBSIZE;
+	uint32_t saveDSPBPOS;
+	uint32_t saveDSPBSURF;
+	uint32_t saveDSPBCNTR;
+	uint32_t saveDSPBSTATUS;
+	uint32_t save_palette_b[256];
+
+	uint32_t savePIPECCONF;
+	uint32_t saveHTOTAL_C;
+	uint32_t saveHBLANK_C;
+	uint32_t saveHSYNC_C;
+	uint32_t saveVTOTAL_C;
+	uint32_t saveVBLANK_C;
+	uint32_t saveVSYNC_C;
+	uint32_t savePIPECSRC;
+	uint32_t saveDSPCSTRIDE;
+	uint32_t saveDSPCLINOFF;
+	uint32_t saveDSPCTILEOFF;
+	uint32_t saveDSPCSIZE;
+	uint32_t saveDSPCPOS;
+	uint32_t saveDSPCSURF;
+	uint32_t saveDSPCCNTR;
+	uint32_t saveDSPCSTATUS;
+	uint32_t save_palette_c[256];
+	uint32_t saveMIPI_C;
+
+	uint32_t savePFIT_CONTROL;
+	uint32_t savePFIT_PGM_RATIOS;
+	uint32_t saveHDMIPHYMISCCTL;
+	uint32_t saveHDMIB_CONTROL;
+};
+
 struct psb_save_area {
 	uint32_t saveBSM;
 	uint32_t saveVBT;
 	union {
 	        struct psb_state psb;
+		struct medfield_state mdfld;
 	};
 	uint32_t saveBLC_PWM_CTL2;
 	uint32_t saveBLC_PWM_CTL;
@@ -563,6 +631,24 @@ struct drm_psb_private {
 
 	/* 2D acceleration */
 	spinlock_t lock_2d;
+
+	/*
+	 * Panel brightness
+	 */
+	int brightness;
+	int brightness_adjusted;
+
+	bool dsr_enable;
+	u32 dsr_fb_update;
+	bool dpi_panel_on[3];
+	void *dsi_configs[2];
+	u32 bpp;
+	u32 bpp2;
+
+	u32 pipeconf[3];
+	u32 dspcntr[3];
+
+	int mdfld_panel_id;
 };
 
 
@@ -758,6 +844,9 @@ extern const struct psb_ops psb_chip_ops;
 /* oaktrail_device.c */
 extern const struct psb_ops oaktrail_chip_ops;
 
+/* mdlfd_device.c */
+extern const struct psb_ops mdfld_chip_ops;
+
 /* cdv_device.c */
 extern const struct psb_ops cdv_chip_ops;
 
diff --git a/drivers/gpu/drm/gma500/psb_irq.c b/drivers/gpu/drm/gma500/psb_irq.c
index 7be802baceb..a86fc3c4bf3 100644
--- a/drivers/gpu/drm/gma500/psb_irq.c
+++ b/drivers/gpu/drm/gma500/psb_irq.c
@@ -27,6 +27,8 @@
 #include "psb_reg.h"
 #include "psb_intel_reg.h"
 #include "power.h"
+#include "psb_irq.h"
+#include "mdfld_output.h"
 
 /*
  * inline functions
@@ -453,6 +455,11 @@ int psb_enable_vblank(struct drm_device *dev, int pipe)
 	uint32_t reg_val = 0;
 	uint32_t pipeconf_reg = mid_pipeconf(pipe);
 
+	/* Medfield is different - we should perhaps extract out vblank
+	   and blacklight etc ops */
+	if (IS_MFLD(dev))
+		return mdfld_enable_te(dev, pipe);
+
 	if (gma_power_begin(dev, false)) {
 		reg_val = REG_READ(pipeconf_reg);
 		gma_power_end(dev);
@@ -485,6 +492,8 @@ void psb_disable_vblank(struct drm_device *dev, int pipe)
 	struct drm_psb_private *dev_priv = dev->dev_private;
 	unsigned long irqflags;
 
+	if (IS_MFLD(dev))
+		mdfld_disable_te(dev, pipe);
 	spin_lock_irqsave(&dev_priv->irqmask_lock, irqflags);
 
 	if (pipe == 0)
@@ -499,6 +508,55 @@ void psb_disable_vblank(struct drm_device *dev, int pipe)
 	spin_unlock_irqrestore(&dev_priv->irqmask_lock, irqflags);
 }
 
+/*
+ * It is used to enable TE interrupt
+ */
+int mdfld_enable_te(struct drm_device *dev, int pipe)
+{
+	struct drm_psb_private *dev_priv =
+		(struct drm_psb_private *) dev->dev_private;
+	unsigned long irqflags;
+	uint32_t reg_val = 0;
+	uint32_t pipeconf_reg = mid_pipeconf(pipe);
+
+	if (gma_power_begin(dev, false)) {
+		reg_val = REG_READ(pipeconf_reg);
+		gma_power_end(dev);
+	}
+
+	if (!(reg_val & PIPEACONF_ENABLE))
+		return -EINVAL;
+
+	spin_lock_irqsave(&dev_priv->irqmask_lock, irqflags);
+
+	mid_enable_pipe_event(dev_priv, pipe);
+	psb_enable_pipestat(dev_priv, pipe, PIPE_TE_ENABLE);
+
+	spin_unlock_irqrestore(&dev_priv->irqmask_lock, irqflags);
+
+	return 0;
+}
+
+/*
+ * It is used to disable TE interrupt
+ */
+void mdfld_disable_te(struct drm_device *dev, int pipe)
+{
+	struct drm_psb_private *dev_priv =
+		(struct drm_psb_private *) dev->dev_private;
+	unsigned long irqflags;
+
+	if (!dev_priv->dsr_enable)
+		return;
+
+	spin_lock_irqsave(&dev_priv->irqmask_lock, irqflags);
+
+	mid_disable_pipe_event(dev_priv, pipe);
+	psb_disable_pipestat(dev_priv, pipe, PIPE_TE_ENABLE);
+
+	spin_unlock_irqrestore(&dev_priv->irqmask_lock, irqflags);
+}
+
 /* Called from drm generic code, passed a 'crtc', which
  * we use as a pipe index
  */
diff --git a/drivers/gpu/drm/gma500/psb_irq.h b/drivers/gpu/drm/gma500/psb_irq.h
index 216fda38b57..603045bee58 100644
--- a/drivers/gpu/drm/gma500/psb_irq.h
+++ b/drivers/gpu/drm/gma500/psb_irq.h
@@ -42,4 +42,6 @@ int  psb_enable_vblank(struct drm_device *dev, int pipe);
 void psb_disable_vblank(struct drm_device *dev, int pipe);
 u32  psb_get_vblank_counter(struct drm_device *dev, int pipe);
 
+int mdfld_enable_te(struct drm_device *dev, int pipe);
+void mdfld_disable_te(struct drm_device *dev, int pipe);
 #endif /* _SYSIRQ_H_ */
diff --git a/drivers/gpu/drm/gma500/tc35876x-dsi-lvds.c b/drivers/gpu/drm/gma500/tc35876x-dsi-lvds.c
new file mode 100644
index 00000000000..4a07ab59617
--- /dev/null
+++ b/drivers/gpu/drm/gma500/tc35876x-dsi-lvds.c
@@ -0,0 +1,829 @@
+/*
+ * Copyright © 2011 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+#include "mdfld_dsi_dpi.h"
+#include "mdfld_output.h"
+#include "mdfld_dsi_pkg_sender.h"
+#include "tc35876x-dsi-lvds.h"
+#include <linux/i2c/tc35876x.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <asm/intel_scu_ipc.h>
+
+static struct i2c_client *tc35876x_client;
+static struct i2c_client *cmi_lcd_i2c_client;
+
+#define FLD_MASK(start, end)	(((1 << ((start) - (end) + 1)) - 1) << (end))
+#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end))
+
+/* DSI D-PHY Layer Registers */
+#define D0W_DPHYCONTTX		0x0004
+#define CLW_DPHYCONTRX		0x0020
+#define D0W_DPHYCONTRX		0x0024
+#define D1W_DPHYCONTRX		0x0028
+#define D2W_DPHYCONTRX		0x002C
+#define D3W_DPHYCONTRX		0x0030
+#define COM_DPHYCONTRX		0x0038
+#define CLW_CNTRL		0x0040
+#define D0W_CNTRL		0x0044
+#define D1W_CNTRL		0x0048
+#define D2W_CNTRL		0x004C
+#define D3W_CNTRL		0x0050
+#define DFTMODE_CNTRL		0x0054
+
+/* DSI PPI Layer Registers */
+#define PPI_STARTPPI		0x0104
+#define PPI_BUSYPPI		0x0108
+#define PPI_LINEINITCNT		0x0110
+#define PPI_LPTXTIMECNT		0x0114
+#define PPI_LANEENABLE		0x0134
+#define PPI_TX_RX_TA		0x013C
+#define PPI_CLS_ATMR		0x0140
+#define PPI_D0S_ATMR		0x0144
+#define PPI_D1S_ATMR		0x0148
+#define PPI_D2S_ATMR		0x014C
+#define PPI_D3S_ATMR		0x0150
+#define PPI_D0S_CLRSIPOCOUNT	0x0164
+#define PPI_D1S_CLRSIPOCOUNT	0x0168
+#define PPI_D2S_CLRSIPOCOUNT	0x016C
+#define PPI_D3S_CLRSIPOCOUNT	0x0170
+#define CLS_PRE			0x0180
+#define D0S_PRE			0x0184
+#define D1S_PRE			0x0188
+#define D2S_PRE			0x018C
+#define D3S_PRE			0x0190
+#define CLS_PREP		0x01A0
+#define D0S_PREP		0x01A4
+#define D1S_PREP		0x01A8
+#define D2S_PREP		0x01AC
+#define D3S_PREP		0x01B0
+#define CLS_ZERO		0x01C0
+#define D0S_ZERO		0x01C4
+#define D1S_ZERO		0x01C8
+#define D2S_ZERO		0x01CC
+#define D3S_ZERO		0x01D0
+#define PPI_CLRFLG		0x01E0
+#define PPI_CLRSIPO		0x01E4
+#define HSTIMEOUT		0x01F0
+#define HSTIMEOUTENABLE		0x01F4
+
+/* DSI Protocol Layer Registers */
+#define DSI_STARTDSI		0x0204
+#define DSI_BUSYDSI		0x0208
+#define DSI_LANEENABLE		0x0210
+#define DSI_LANESTATUS0		0x0214
+#define DSI_LANESTATUS1		0x0218
+#define DSI_INTSTATUS		0x0220
+#define DSI_INTMASK		0x0224
+#define DSI_INTCLR		0x0228
+#define DSI_LPTXTO		0x0230
+
+/* DSI General Registers */
+#define DSIERRCNT		0x0300
+
+/* DSI Application Layer Registers */
+#define APLCTRL			0x0400
+#define RDPKTLN			0x0404
+
+/* Video Path Registers */
+#define VPCTRL			0x0450
+#define HTIM1			0x0454
+#define HTIM2			0x0458
+#define VTIM1			0x045C
+#define VTIM2			0x0460
+#define VFUEN			0x0464
+
+/* LVDS Registers */
+#define LVMX0003		0x0480
+#define LVMX0407		0x0484
+#define LVMX0811		0x0488
+#define LVMX1215		0x048C
+#define LVMX1619		0x0490
+#define LVMX2023		0x0494
+#define LVMX2427		0x0498
+#define LVCFG			0x049C
+#define LVPHY0			0x04A0
+#define LVPHY1			0x04A4
+
+/* System Registers */
+#define SYSSTAT			0x0500
+#define SYSRST			0x0504
+
+/* GPIO Registers */
+/*#define GPIOC			0x0520*/
+#define GPIOO			0x0524
+#define GPIOI			0x0528
+
+/* I2C Registers */
+#define I2CTIMCTRL		0x0540
+#define I2CMADDR		0x0544
+#define WDATAQ			0x0548
+#define RDATAQ			0x054C
+
+/* Chip/Rev Registers */
+#define IDREG			0x0580
+
+/* Debug Registers */
+#define DEBUG00			0x05A0
+#define DEBUG01			0x05A4
+
+/* Panel CABC registers */
+#define PANEL_PWM_CONTROL	0x90
+#define PANEL_FREQ_DIVIDER_HI	0x91
+#define PANEL_FREQ_DIVIDER_LO	0x92
+#define PANEL_DUTY_CONTROL	0x93
+#define PANEL_MODIFY_RGB	0x94
+#define PANEL_FRAMERATE_CONTROL	0x96
+#define PANEL_PWM_MIN		0x97
+#define PANEL_PWM_REF		0x98
+#define PANEL_PWM_MAX		0x99
+#define PANEL_ALLOW_DISTORT	0x9A
+#define PANEL_BYPASS_PWMI	0x9B
+
+/* Panel color management registers */
+#define PANEL_CM_ENABLE		0x700
+#define PANEL_CM_HUE		0x701
+#define PANEL_CM_SATURATION	0x702
+#define PANEL_CM_INTENSITY	0x703
+#define PANEL_CM_BRIGHTNESS	0x704
+#define PANEL_CM_CE_ENABLE	0x705
+#define PANEL_CM_PEAK_EN	0x710
+#define PANEL_CM_GAIN		0x711
+#define PANEL_CM_HUETABLE_START	0x730
+#define PANEL_CM_HUETABLE_END	0x747 /* inclusive */
+
+/* Input muxing for registers LVMX0003...LVMX2427 */
+enum {
+	INPUT_R0,	/* 0 */
+	INPUT_R1,
+	INPUT_R2,
+	INPUT_R3,
+	INPUT_R4,
+	INPUT_R5,
+	INPUT_R6,
+	INPUT_R7,
+	INPUT_G0,	/* 8 */
+	INPUT_G1,
+	INPUT_G2,
+	INPUT_G3,
+	INPUT_G4,
+	INPUT_G5,
+	INPUT_G6,
+	INPUT_G7,
+	INPUT_B0,	/* 16 */
+	INPUT_B1,
+	INPUT_B2,
+	INPUT_B3,
+	INPUT_B4,
+	INPUT_B5,
+	INPUT_B6,
+	INPUT_B7,
+	INPUT_HSYNC,	/* 24 */
+	INPUT_VSYNC,
+	INPUT_DE,
+	LOGIC_0,
+	/* 28...31 undefined */
+};
+
+#define INPUT_MUX(lvmx03, lvmx02, lvmx01, lvmx00)		\
+	(FLD_VAL(lvmx03, 29, 24) | FLD_VAL(lvmx02, 20, 16) |	\
+	FLD_VAL(lvmx01, 12, 8) | FLD_VAL(lvmx00, 4, 0))
+
+/**
+ * tc35876x_regw - Write DSI-LVDS bridge register using I2C
+ * @client: struct i2c_client to use
+ * @reg: register address
+ * @value: value to write
+ *
+ * Returns 0 on success, or a negative error value.
+ */
+static int tc35876x_regw(struct i2c_client *client, u16 reg, u32 value)
+{
+	int r;
+	u8 tx_data[] = {
+		/* NOTE: Register address big-endian, data little-endian. */
+		(reg >> 8) & 0xff,
+		reg & 0xff,
+		value & 0xff,
+		(value >> 8) & 0xff,
+		(value >> 16) & 0xff,
+		(value >> 24) & 0xff,
+	};
+	struct i2c_msg msgs[] = {
+		{
+			.addr = client->addr,
+			.flags = 0,
+			.buf = tx_data,
+			.len = ARRAY_SIZE(tx_data),
+		},
+	};
+
+	r = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (r < 0) {
+		dev_err(&client->dev, "%s: reg 0x%04x val 0x%08x error %d\n",
+			__func__, reg, value, r);
+		return r;
+	}
+
+	if (r < ARRAY_SIZE(msgs)) {
+		dev_err(&client->dev, "%s: reg 0x%04x val 0x%08x msgs %d\n",
+			__func__, reg, value, r);
+		return -EAGAIN;
+	}
+
+	dev_dbg(&client->dev, "%s: reg 0x%04x val 0x%08x\n",
+			__func__, reg, value);
+
+	return 0;
+}
+
+/**
+ * tc35876x_regr - Read DSI-LVDS bridge register using I2C
+ * @client: struct i2c_client to use
+ * @reg: register address
+ * @value: pointer for storing the value
+ *
+ * Returns 0 on success, or a negative error value.
+ */
+static int tc35876x_regr(struct i2c_client *client, u16 reg, u32 *value)
+{
+	int r;
+	u8 tx_data[] = {
+		(reg >> 8) & 0xff,
+		reg & 0xff,
+	};
+	u8 rx_data[4];
+	struct i2c_msg msgs[] = {
+		{
+			.addr = client->addr,
+			.flags = 0,
+			.buf = tx_data,
+			.len = ARRAY_SIZE(tx_data),
+		},
+		{
+			.addr = client->addr,
+			.flags = I2C_M_RD,
+			.buf = rx_data,
+			.len = ARRAY_SIZE(rx_data),
+		 },
+	};
+
+	r = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (r < 0) {
+		dev_err(&client->dev, "%s: reg 0x%04x error %d\n", __func__,
+			reg, r);
+		return r;
+	}
+
+	if (r < ARRAY_SIZE(msgs)) {
+		dev_err(&client->dev, "%s: reg 0x%04x msgs %d\n", __func__,
+			reg, r);
+		return -EAGAIN;
+	}
+
+	*value = rx_data[0] << 24 | rx_data[1] << 16 |
+		rx_data[2] << 8 | rx_data[3];
+
+	dev_dbg(&client->dev, "%s: reg 0x%04x value 0x%08x\n", __func__,
+		reg, *value);
+
+	return 0;
+}
+
+void tc35876x_set_bridge_reset_state(struct drm_device *dev, int state)
+{
+	struct tc35876x_platform_data *pdata;
+
+	if (WARN(!tc35876x_client, "%s called before probe", __func__))
+		return;
+
+	dev_dbg(&tc35876x_client->dev, "%s: state %d\n", __func__, state);
+
+	pdata = dev_get_platdata(&tc35876x_client->dev);
+
+	if (pdata->gpio_bridge_reset == -1)
+		return;
+
+	if (state) {
+		gpio_set_value_cansleep(pdata->gpio_bridge_reset, 0);
+		mdelay(10);
+	} else {
+		/* Pull MIPI Bridge reset pin to Low */
+		gpio_set_value_cansleep(pdata->gpio_bridge_reset, 0);
+		mdelay(20);
+		/* Pull MIPI Bridge reset pin to High */
+		gpio_set_value_cansleep(pdata->gpio_bridge_reset, 1);
+		mdelay(40);
+	}
+}
+
+void tc35876x_configure_lvds_bridge(struct drm_device *dev)
+{
+	struct i2c_client *i2c = tc35876x_client;
+	u32 ppi_lptxtimecnt;
+	u32 txtagocnt;
+	u32 txtasurecnt;
+	u32 id;
+
+	if (WARN(!tc35876x_client, "%s called before probe", __func__))
+		return;
+
+	dev_dbg(&tc35876x_client->dev, "%s\n", __func__);
+
+	if (!tc35876x_regr(i2c, IDREG, &id))
+		dev_info(&tc35876x_client->dev, "tc35876x ID 0x%08x\n", id);
+	else
+		dev_err(&tc35876x_client->dev, "Cannot read ID\n");
+
+	ppi_lptxtimecnt = 4;
+	txtagocnt = (5 * ppi_lptxtimecnt - 3) / 4;
+	txtasurecnt = 3 * ppi_lptxtimecnt / 2;
+	tc35876x_regw(i2c, PPI_TX_RX_TA, FLD_VAL(txtagocnt, 26, 16) |
+		FLD_VAL(txtasurecnt, 10, 0));
+	tc35876x_regw(i2c, PPI_LPTXTIMECNT, FLD_VAL(ppi_lptxtimecnt, 10, 0));
+
+	tc35876x_regw(i2c, PPI_D0S_CLRSIPOCOUNT, FLD_VAL(1, 5, 0));
+	tc35876x_regw(i2c, PPI_D1S_CLRSIPOCOUNT, FLD_VAL(1, 5, 0));
+	tc35876x_regw(i2c, PPI_D2S_CLRSIPOCOUNT, FLD_VAL(1, 5, 0));
+	tc35876x_regw(i2c, PPI_D3S_CLRSIPOCOUNT, FLD_VAL(1, 5, 0));
+
+	/* Enabling MIPI & PPI lanes, Enable 4 lanes */
+	tc35876x_regw(i2c, PPI_LANEENABLE,
+		BIT(4) | BIT(3) | BIT(2) | BIT(1) | BIT(0));
+	tc35876x_regw(i2c, DSI_LANEENABLE,
+		BIT(4) | BIT(3) | BIT(2) | BIT(1) | BIT(0));
+	tc35876x_regw(i2c, PPI_STARTPPI, BIT(0));
+	tc35876x_regw(i2c, DSI_STARTDSI, BIT(0));
+
+	/* Setting LVDS output frequency */
+	tc35876x_regw(i2c, LVPHY0, FLD_VAL(1, 20, 16) |
+		FLD_VAL(2, 15, 14) | FLD_VAL(6, 4, 0)); /* 0x00048006 */
+
+	/* Setting video panel control register,0x00000120 VTGen=ON ?!?!? */
+	tc35876x_regw(i2c, VPCTRL, BIT(8) | BIT(5));
+
+	/* Horizontal back porch and horizontal pulse width. 0x00280028 */
+	tc35876x_regw(i2c, HTIM1, FLD_VAL(40, 24, 16) | FLD_VAL(40, 8, 0));
+
+	/* Horizontal front porch and horizontal active video size. 0x00500500*/
+	tc35876x_regw(i2c, HTIM2, FLD_VAL(80, 24, 16) | FLD_VAL(1280, 10, 0));
+
+	/* Vertical back porch and vertical sync pulse width. 0x000e000a */
+	tc35876x_regw(i2c, VTIM1, FLD_VAL(14, 23, 16) | FLD_VAL(10, 7, 0));
+
+	/* Vertical front porch and vertical display size. 0x000e0320 */
+	tc35876x_regw(i2c, VTIM2, FLD_VAL(14, 23, 16) | FLD_VAL(800, 10, 0));
+
+	/* Set above HTIM1, HTIM2, VTIM1, and VTIM2 at next VSYNC. */
+	tc35876x_regw(i2c, VFUEN, BIT(0));
+
+	/* Soft reset LCD controller. */
+	tc35876x_regw(i2c, SYSRST, BIT(2));
+
+	/* LVDS-TX input muxing */
+	tc35876x_regw(i2c, LVMX0003,
+		INPUT_MUX(INPUT_R5, INPUT_R4, INPUT_R3, INPUT_R2));
+	tc35876x_regw(i2c, LVMX0407,
+		INPUT_MUX(INPUT_G2, INPUT_R7, INPUT_R1, INPUT_R6));
+	tc35876x_regw(i2c, LVMX0811,
+		INPUT_MUX(INPUT_G1, INPUT_G0, INPUT_G4, INPUT_G3));
+	tc35876x_regw(i2c, LVMX1215,
+		INPUT_MUX(INPUT_B2, INPUT_G7, INPUT_G6, INPUT_G5));
+	tc35876x_regw(i2c, LVMX1619,
+		INPUT_MUX(INPUT_B4, INPUT_B3, INPUT_B1, INPUT_B0));
+	tc35876x_regw(i2c, LVMX2023,
+		INPUT_MUX(LOGIC_0,  INPUT_B7, INPUT_B6, INPUT_B5));
+	tc35876x_regw(i2c, LVMX2427,
+		INPUT_MUX(INPUT_R0, INPUT_DE, INPUT_VSYNC, INPUT_HSYNC));
+
+	/* Enable LVDS transmitter. */
+	tc35876x_regw(i2c, LVCFG, BIT(0));
+
+	/* Clear notifications. Don't write reserved bits. Was write 0xffffffff
+	 * to 0x0288, must be in error?! */
+	tc35876x_regw(i2c, DSI_INTCLR, FLD_MASK(31, 30) | FLD_MASK(22, 0));
+}
+
+#define GPIOPWMCTRL	0x38F
+#define PWM0CLKDIV0	0x62 /* low byte */
+#define PWM0CLKDIV1	0x61 /* high byte */
+
+#define SYSTEMCLK	19200000UL /* 19.2 MHz */
+#define PWM_FREQUENCY	9600 /* Hz */
+
+/* f = baseclk / (clkdiv + 1) => clkdiv = (baseclk - f) / f */
+static inline u16 calc_clkdiv(unsigned long baseclk, unsigned int f)
+{
+	return (baseclk - f) / f;
+}
+
+static void tc35876x_brightness_init(struct drm_device *dev)
+{
+	int ret;
+	u8 pwmctrl;
+	u16 clkdiv;
+
+	/* Make sure the PWM reference is the 19.2 MHz system clock. Read first
+	 * instead of setting directly to catch potential conflicts between PWM
+	 * users. */
+	ret = intel_scu_ipc_ioread8(GPIOPWMCTRL, &pwmctrl);
+	if (ret || pwmctrl != 0x01) {
+		if (ret)
+			dev_err(&dev->pdev->dev, "GPIOPWMCTRL read failed\n");
+		else
+			dev_warn(&dev->pdev->dev, "GPIOPWMCTRL was not set to system clock (pwmctrl = 0x%02x)\n", pwmctrl);
+
+		ret = intel_scu_ipc_iowrite8(GPIOPWMCTRL, 0x01);
+		if (ret)
+			dev_err(&dev->pdev->dev, "GPIOPWMCTRL set failed\n");
+	}
+
+	clkdiv = calc_clkdiv(SYSTEMCLK, PWM_FREQUENCY);
+
+	ret = intel_scu_ipc_iowrite8(PWM0CLKDIV1, (clkdiv >> 8) & 0xff);
+	if (!ret)
+		ret = intel_scu_ipc_iowrite8(PWM0CLKDIV0, clkdiv & 0xff);
+
+	if (ret)
+		dev_err(&dev->pdev->dev, "PWM0CLKDIV set failed\n");
+	else
+		dev_dbg(&dev->pdev->dev, "PWM0CLKDIV set to 0x%04x (%d Hz)\n",
+			clkdiv, PWM_FREQUENCY);
+}
+
+#define PWM0DUTYCYCLE			0x67
+
+void tc35876x_brightness_control(struct drm_device *dev, int level)
+{
+	int ret;
+	u8 duty_val;
+	u8 panel_duty_val;
+
+	level = clamp(level, 0, MDFLD_DSI_BRIGHTNESS_MAX_LEVEL);
+
+	/* PWM duty cycle 0x00...0x63 corresponds to 0...99% */
+	duty_val = level * 0x63 / MDFLD_DSI_BRIGHTNESS_MAX_LEVEL;
+
+	/* I won't pretend to understand this formula. The panel spec is quite
+	 * bad engrish.
+	 */
+	panel_duty_val = (2 * level - 100) * 0xA9 /
+			 MDFLD_DSI_BRIGHTNESS_MAX_LEVEL + 0x56;
+
+	ret = intel_scu_ipc_iowrite8(PWM0DUTYCYCLE, duty_val);
+	if (ret)
+		dev_err(&tc35876x_client->dev, "%s: ipc write fail\n",
+			__func__);
+
+	if (cmi_lcd_i2c_client) {
+		ret = i2c_smbus_write_byte_data(cmi_lcd_i2c_client,
+						PANEL_PWM_MAX, panel_duty_val);
+		if (ret < 0)
+			dev_err(&cmi_lcd_i2c_client->dev, "%s: i2c write failed\n",
+				__func__);
+	}
+}
+
+void tc35876x_toshiba_bridge_panel_off(struct drm_device *dev)
+{
+	struct tc35876x_platform_data *pdata;
+
+	if (WARN(!tc35876x_client, "%s called before probe", __func__))
+		return;
+
+	dev_dbg(&tc35876x_client->dev, "%s\n", __func__);
+
+	pdata = dev_get_platdata(&tc35876x_client->dev);
+
+	if (pdata->gpio_panel_bl_en != -1)
+		gpio_set_value_cansleep(pdata->gpio_panel_bl_en, 0);
+
+	if (pdata->gpio_panel_vadd != -1)
+		gpio_set_value_cansleep(pdata->gpio_panel_vadd, 0);
+}
+
+void tc35876x_toshiba_bridge_panel_on(struct drm_device *dev)
+{
+	struct tc35876x_platform_data *pdata;
+	struct drm_psb_private *dev_priv = dev->dev_private;
+
+	if (WARN(!tc35876x_client, "%s called before probe", __func__))
+		return;
+
+	dev_dbg(&tc35876x_client->dev, "%s\n", __func__);
+
+	pdata = dev_get_platdata(&tc35876x_client->dev);
+
+	if (pdata->gpio_panel_vadd != -1) {
+		gpio_set_value_cansleep(pdata->gpio_panel_vadd, 1);
+		msleep(260);
+	}
+
+	if (cmi_lcd_i2c_client) {
+		int ret;
+		dev_dbg(&cmi_lcd_i2c_client->dev, "setting TCON\n");
+		/* Bit 4 is average_saving. Setting it to 1, the brightness is
+		 * referenced to the average of the frame content. 0 means
+		 * reference to the maximum of frame contents. Bits 3:0 are
+		 * allow_distort. When set to a nonzero value, all color values
+		 * between 255-allow_distort*2 and 255 are mapped to the
+		 * 255-allow_distort*2 value.
+		 */
+		ret = i2c_smbus_write_byte_data(cmi_lcd_i2c_client,
+						PANEL_ALLOW_DISTORT, 0x10);
+		if (ret < 0)
+			dev_err(&cmi_lcd_i2c_client->dev,
+				"i2c write failed (%d)\n", ret);
+		ret = i2c_smbus_write_byte_data(cmi_lcd_i2c_client,
+						PANEL_BYPASS_PWMI, 0);
+		if (ret < 0)
+			dev_err(&cmi_lcd_i2c_client->dev,
+				"i2c write failed (%d)\n", ret);
+		/* Set minimum brightness value - this is tunable */
+		ret = i2c_smbus_write_byte_data(cmi_lcd_i2c_client,
+						PANEL_PWM_MIN, 0x35);
+		if (ret < 0)
+			dev_err(&cmi_lcd_i2c_client->dev,
+				"i2c write failed (%d)\n", ret);
+	}
+
+	if (pdata->gpio_panel_bl_en != -1)
+		gpio_set_value_cansleep(pdata->gpio_panel_bl_en, 1);
+
+	tc35876x_brightness_control(dev, dev_priv->brightness_adjusted);
+}
+
+static struct drm_display_mode *tc35876x_get_config_mode(struct drm_device *dev)
+{
+	struct drm_display_mode *mode;
+
+	dev_dbg(&dev->pdev->dev, "%s\n", __func__);
+
+	mode = kzalloc(sizeof(*mode), GFP_KERNEL);
+	if (!mode)
+		return NULL;
+
+	/* FIXME: do this properly. */
+	mode->hdisplay = 1280;
+	mode->vdisplay = 800;
+	mode->hsync_start = 1360;
+	mode->hsync_end = 1400;
+	mode->htotal = 1440;
+	mode->vsync_start = 814;
+	mode->vsync_end = 824;
+	mode->vtotal = 838;
+	mode->clock = 33324 << 1;
+
+	dev_info(&dev->pdev->dev, "hdisplay(w) = %d\n", mode->hdisplay);
+	dev_info(&dev->pdev->dev, "vdisplay(h) = %d\n", mode->vdisplay);
+	dev_info(&dev->pdev->dev, "HSS = %d\n", mode->hsync_start);
+	dev_info(&dev->pdev->dev, "HSE = %d\n", mode->hsync_end);
+	dev_info(&dev->pdev->dev, "htotal = %d\n", mode->htotal);
+	dev_info(&dev->pdev->dev, "VSS = %d\n", mode->vsync_start);
+	dev_info(&dev->pdev->dev, "VSE = %d\n", mode->vsync_end);
+	dev_info(&dev->pdev->dev, "vtotal = %d\n", mode->vtotal);
+	dev_info(&dev->pdev->dev, "clock = %d\n", mode->clock);
+
+	drm_mode_set_name(mode);
+	drm_mode_set_crtcinfo(mode, 0);
+
+	mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+	return mode;
+}
+
+/* DV1 Active area 216.96 x 135.6 mm */
+#define DV1_PANEL_WIDTH 217
+#define DV1_PANEL_HEIGHT 136
+
+static int tc35876x_get_panel_info(struct drm_device *dev, int pipe,
+				struct panel_info *pi)
+{
+	if (!dev || !pi)
+		return -EINVAL;
+
+	pi->width_mm = DV1_PANEL_WIDTH;
+	pi->height_mm = DV1_PANEL_HEIGHT;
+
+	return 0;
+}
+
+static int tc35876x_bridge_probe(struct i2c_client *client,
+				const struct i2c_device_id *id)
+{
+	struct tc35876x_platform_data *pdata;
+
+	dev_info(&client->dev, "%s\n", __func__);
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev, "%s: i2c_check_functionality() failed\n",
+			__func__);
+		return -ENODEV;
+	}
+
+	pdata = dev_get_platdata(&client->dev);
+	if (!pdata) {
+		dev_err(&client->dev, "%s: no platform data\n", __func__);
+		return -ENODEV;
+	}
+
+	if (pdata->gpio_bridge_reset != -1) {
+		gpio_request(pdata->gpio_bridge_reset, "tc35876x bridge reset");
+		gpio_direction_output(pdata->gpio_bridge_reset, 0);
+	}
+
+	if (pdata->gpio_panel_bl_en != -1) {
+		gpio_request(pdata->gpio_panel_bl_en, "tc35876x panel bl en");
+		gpio_direction_output(pdata->gpio_panel_bl_en, 0);
+	}
+
+	if (pdata->gpio_panel_vadd != -1) {
+		gpio_request(pdata->gpio_panel_vadd, "tc35876x panel vadd");
+		gpio_direction_output(pdata->gpio_panel_vadd, 0);
+	}
+
+	tc35876x_client = client;
+
+	return 0;
+}
+
+static int tc35876x_bridge_remove(struct i2c_client *client)
+{
+	struct tc35876x_platform_data *pdata = dev_get_platdata(&client->dev);
+
+	dev_dbg(&client->dev, "%s\n", __func__);
+
+	if (pdata->gpio_bridge_reset != -1)
+		gpio_free(pdata->gpio_bridge_reset);
+
+	if (pdata->gpio_panel_bl_en != -1)
+		gpio_free(pdata->gpio_panel_bl_en);
+
+	if (pdata->gpio_panel_vadd != -1)
+		gpio_free(pdata->gpio_panel_vadd);
+
+	tc35876x_client = NULL;
+
+	return 0;
+}
+
+static const struct i2c_device_id tc35876x_bridge_id[] = {
+	{ "i2c_disp_brig", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, tc35876x_bridge_id);
+
+static struct i2c_driver tc35876x_bridge_i2c_driver = {
+	.driver = {
+		.name = "i2c_disp_brig",
+	},
+	.id_table = tc35876x_bridge_id,
+	.probe = tc35876x_bridge_probe,
+	.remove = __devexit_p(tc35876x_bridge_remove),
+};
+
+/* LCD panel I2C */
+static int cmi_lcd_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	dev_info(&client->dev, "%s\n", __func__);
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev, "%s: i2c_check_functionality() failed\n",
+			__func__);
+		return -ENODEV;
+	}
+
+	cmi_lcd_i2c_client = client;
+
+	return 0;
+}
+
+static int cmi_lcd_i2c_remove(struct i2c_client *client)
+{
+	dev_dbg(&client->dev, "%s\n", __func__);
+
+	cmi_lcd_i2c_client = NULL;
+
+	return 0;
+}
+
+static const struct i2c_device_id cmi_lcd_i2c_id[] = {
+	{ "cmi-lcd", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, cmi_lcd_i2c_id);
+
+static struct i2c_driver cmi_lcd_i2c_driver = {
+	.driver = {
+		.name = "cmi-lcd",
+	},
+	.id_table = cmi_lcd_i2c_id,
+	.probe = cmi_lcd_i2c_probe,
+	.remove = __devexit_p(cmi_lcd_i2c_remove),
+};
+
+/* HACK to create I2C device while it's not created by platform code */
+#define CMI_LCD_I2C_ADAPTER	2
+#define CMI_LCD_I2C_ADDR	0x60
+
+static int cmi_lcd_hack_create_device(void)
+{
+	struct i2c_adapter *adapter;
+	struct i2c_client *client;
+	struct i2c_board_info info = {
+		.type = "cmi-lcd",
+		.addr = CMI_LCD_I2C_ADDR,
+	};
+
+	pr_debug("%s\n", __func__);
+
+	adapter = i2c_get_adapter(CMI_LCD_I2C_ADAPTER);
+	if (!adapter) {
+		pr_err("%s: i2c_get_adapter(%d) failed\n", __func__,
+			CMI_LCD_I2C_ADAPTER);
+		return -EINVAL;
+	}
+
+	client = i2c_new_device(adapter, &info);
+	if (!client) {
+		pr_err("%s: i2c_new_device() failed\n", __func__);
+		i2c_put_adapter(adapter);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct drm_encoder_helper_funcs tc35876x_encoder_helper_funcs = {
+	.dpms = mdfld_dsi_dpi_dpms,
+	.mode_fixup = mdfld_dsi_dpi_mode_fixup,
+	.prepare = mdfld_dsi_dpi_prepare,
+	.mode_set = mdfld_dsi_dpi_mode_set,
+	.commit = mdfld_dsi_dpi_commit,
+};
+
+static const struct drm_encoder_funcs tc35876x_encoder_funcs = {
+	.destroy = drm_encoder_cleanup,
+};
+
+const struct panel_funcs mdfld_tc35876x_funcs = {
+	.encoder_funcs = &tc35876x_encoder_funcs,
+	.encoder_helper_funcs = &tc35876x_encoder_helper_funcs,
+	.get_config_mode = tc35876x_get_config_mode,
+	.get_panel_info = tc35876x_get_panel_info,
+};
+
+void tc35876x_init(struct drm_device *dev)
+{
+	int r;
+
+	dev_dbg(&dev->pdev->dev, "%s\n", __func__);
+
+	cmi_lcd_hack_create_device();
+
+	r = i2c_add_driver(&cmi_lcd_i2c_driver);
+	if (r < 0)
+		dev_err(&dev->pdev->dev,
+			"%s: i2c_add_driver() for %s failed (%d)\n",
+			__func__, cmi_lcd_i2c_driver.driver.name, r);
+
+	r = i2c_add_driver(&tc35876x_bridge_i2c_driver);
+	if (r < 0)
+		dev_err(&dev->pdev->dev,
+			"%s: i2c_add_driver() for %s failed (%d)\n",
+			__func__, tc35876x_bridge_i2c_driver.driver.name, r);
+
+	tc35876x_brightness_init(dev);
+}
+
+void tc35876x_exit(void)
+{
+	pr_debug("%s\n", __func__);
+
+	i2c_del_driver(&tc35876x_bridge_i2c_driver);
+
+	if (cmi_lcd_i2c_client)
+		i2c_del_driver(&cmi_lcd_i2c_driver);
+}
diff --git a/drivers/gpu/drm/gma500/tc35876x-dsi-lvds.h b/drivers/gpu/drm/gma500/tc35876x-dsi-lvds.h
new file mode 100644
index 00000000000..b14b7f9e7d1
--- /dev/null
+++ b/drivers/gpu/drm/gma500/tc35876x-dsi-lvds.h
@@ -0,0 +1,38 @@
+/*
+ * Copyright © 2011 Intel Corporation
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice (including the next
+ * paragraph) shall be included in all copies or substantial portions of the
+ * Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
+ * DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+#ifndef __MDFLD_DSI_LVDS_BRIDGE_H__
+#define __MDFLD_DSI_LVDS_BRIDGE_H__
+
+void tc35876x_set_bridge_reset_state(struct drm_device *dev, int state);
+void tc35876x_configure_lvds_bridge(struct drm_device *dev);
+void tc35876x_brightness_control(struct drm_device *dev, int level);
+void tc35876x_toshiba_bridge_panel_off(struct drm_device *dev);
+void tc35876x_toshiba_bridge_panel_on(struct drm_device *dev);
+void tc35876x_init(struct drm_device *dev);
+void tc35876x_exit(void);
+
+extern const struct panel_funcs mdfld_tc35876x_funcs;
+
+#endif /*__MDFLD_DSI_LVDS_BRIDGE_H__*/
diff --git a/include/linux/i2c/tc35876x.h b/include/linux/i2c/tc35876x.h
new file mode 100644
index 00000000000..cd6a51c71e7
--- /dev/null
+++ b/include/linux/i2c/tc35876x.h
@@ -0,0 +1,11 @@
+
+#ifndef _TC35876X_H
+#define _TC35876X_H
+
+struct tc35876x_platform_data {
+	int gpio_bridge_reset;
+	int gpio_panel_bl_en;
+	int gpio_panel_vadd;
+};
+
+#endif /* _TC35876X_H */