summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorGuenter Roeck <guenter.roeck@ericsson.com>2011-04-02 08:26:34 -0700
committerGuenter Roeck <guenter.roeck@ericsson.com>2011-04-19 08:49:55 -0700
commitc3a2f0ad4917c678fcd828f16102518c33d8393c (patch)
tree7b8809f0386f997920279713894e5ea69b33fdcc
parentf0e615c3cb72b42191b558c130409335812621d8 (diff)
hwmon: Add submitting-patches checklist to documentation
When writing hardware monitoring drivers, there are some common pitfalls which keep coming up in code reviews. This patch provides a document describing all those pitfalls and how to avoid them. Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Jean Delvare <khali@linux-fr.org>
-rw-r--r--Documentation/hwmon/submitting-patches109
1 files changed, 109 insertions, 0 deletions
diff --git a/Documentation/hwmon/submitting-patches b/Documentation/hwmon/submitting-patches
new file mode 100644
index 00000000000..86f42e8e9e4
--- /dev/null
+++ b/Documentation/hwmon/submitting-patches
@@ -0,0 +1,109 @@
+ How to Get Your Patch Accepted Into the Hwmon Subsystem
+ -------------------------------------------------------
+
+This text is is a collection of suggestions for people writing patches or
+drivers for the hwmon subsystem. Following these suggestions will greatly
+increase the chances of your change being accepted.
+
+
+1. General
+----------
+
+* It should be unnecessary to mention, but please read and follow
+ Documentation/SubmitChecklist
+ Documentation/SubmittingDrivers
+ Documentation/SubmittingPatches
+ Documentation/CodingStyle
+
+* If your patch generates checkpatch warnings, please refrain from explanations
+ such as "I don't like that coding style". Keep in mind that each unnecessary
+ warning helps hiding a real problem. If you don't like the kernel coding
+ style, don't write kernel drivers.
+
+* Please test your patch thoroughly. We are not your test group.
+ Sometimes a patch can not or not completely be tested because of missing
+ hardware. In such cases, you should test-build the code on at least one
+ architecture. If run-time testing was not achieved, it should be written
+ explicitly below the patch header.
+
+* If your patch (or the driver) is affected by configuration options such as
+ CONFIG_SMP or CONFIG_HOTPLUG, make sure it compiles for all configuration
+ variants.
+
+
+2. Adding functionality to existing drivers
+-------------------------------------------
+
+* Make sure the documentation in Documentation/hwmon/<driver_name> is up to
+ date.
+
+* Make sure the information in Kconfig is up to date.
+
+* If the added functionality requires some cleanup or structural changes, split
+ your patch into a cleanup part and the actual addition. This makes it easier
+ to review your changes, and to bisect any resulting problems.
+
+* Never mix bug fixes, cleanup, and functional enhancements in a single patch.
+
+
+3. New drivers
+--------------
+
+* Running your patch or driver file(s) through checkpatch does not mean its
+ formatting is clean. If unsure about formatting in your new driver, run it
+ through Lindent. Lindent is not perfect, and you may have to do some minor
+ cleanup, but it is a good start.
+
+* Consider adding yourself to MAINTAINERS.
+
+* Document the driver in Documentation/hwmon/<driver_name>.
+
+* Add the driver to Kconfig and Makefile in alphabetical order.
+
+* Make sure that all dependencies are listed in Kconfig. For new drivers, it
+ is most likely prudent to add a dependency on EXPERIMENTAL.
+
+* Avoid forward declarations if you can. Rearrange the code if necessary.
+
+* Avoid calculations in macros and macro-generated functions. While such macros
+ may save a line or so in the source, it obfuscates the code and makes code
+ review more difficult. It may also result in code which is more complicated
+ than necessary. Use inline functions or just regular functions instead.
+
+* If the driver has a detect function, make sure it is silent. Debug messages
+ and messages printed after a successful detection are acceptable, but it
+ must not print messages such as "Chip XXX not found/supported".
+
+ Keep in mind that the detect function will run for all drivers supporting an
+ address if a chip is detected on that address. Unnecessary messages will just
+ pollute the kernel log and not provide any value.
+
+* Provide a detect function if and only if a chip can be detected reliably.
+
+* Avoid writing to chip registers in the detect function. If you have to write,
+ only do it after you have already gathered enough data to be certain that the
+ detection is going to be successful.
+
+ Keep in mind that the chip might not be what your driver believes it is, and
+ writing to it might cause a bad misconfiguration.
+
+* Make sure there are no race conditions in the probe function. Specifically,
+ completely initialize your chip first, then create sysfs entries and register
+ with the hwmon subsystem.
+
+* Do not provide support for deprecated sysfs attributes.
+
+* Do not create non-standard attributes unless really needed. If you have to use
+ non-standard attributes, or you believe you do, discuss it on the mailing list
+ first. Either case, provide a detailed explanation why you need the
+ non-standard attribute(s).
+ Standard attributes are specified in Documentation/hwmon/sysfs-interface.
+
+* When deciding which sysfs attributes to support, look at the chip's
+ capabilities. While we do not expect your driver to support everything the
+ chip may offer, it should at least support all limits and alarms.
+
+* Last but not least, please check if a driver for your chip already exists
+ before starting to write a new driver. Especially for temperature sensors,
+ new chips are often variants of previously released chips. In some cases,
+ a presumably new chip may simply have been relabeled.