summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2009-09-30 13:46:56 -0700
committerLinus Torvalds <torvalds@linux-foundation.org>2009-09-30 13:46:56 -0700
commite399835c349b7d8339775a004a86a492a444e230 (patch)
tree6e07f8d53e58a6442bf850097179d0202db4766c
parent9abf47f11b38f5ecf411b9a44437cad5016631ad (diff)
parentda3a7a2b9f9776f2d44ed9a4b40eabeb17c6e886 (diff)
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: MIPS: Avoid spurious make includecheck message MIPS: VPE: Get rid of BKL. MIPS: VPE: Fix build after the credential changes a while ago. MIPS: Excite: Get rid of BKL. MIPS: Sibyte: Get rid of BKL. MIPS: BCM63xx: Add PCMCIA & Cardbus support. MIPS: MSP71xx: request_irq() failure ignored in msp_pcibios_config_access() MIPS: Decrease size of au1xxx_dbdma_pm_regs[][] MIPS: SMP: Inline arch_send_call_function_{single_ipi,ipi_mask} MIPS: SMP: Fix build. MIPS: MIPSxx SC: Avoid destructive invalidation on partial L2 cachelines. MIPS: Sibyte: Fix compilation error. MIPS: BCM1480: Re-apply patch lost due to bad resolution of merge conflict. MIPS: BCM63xx: Add serial driver for bcm63xx integrated UART. MIPS: Loongson2: Fix typo "enalbe" -> "enable" MIPS: SMTC: Remove duplicate structure field initialization MIPS: Remove duplicated #include MIPS: BCM63xx: Remove duplicated #include
-rw-r--r--arch/mips/alchemy/common/dbdma.c8
-rw-r--r--arch/mips/basler/excite/excite_iodev.c2
-rw-r--r--arch/mips/bcm63xx/Makefile2
-rw-r--r--arch/mips/bcm63xx/boards/board_bcm963xx.c8
-rw-r--r--arch/mips/bcm63xx/dev-pcmcia.c144
-rw-r--r--arch/mips/bcm63xx/dev-uart.c41
-rw-r--r--arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h13
-rw-r--r--arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h6
-rw-r--r--arch/mips/include/asm/smp.h15
-rw-r--r--arch/mips/include/asm/unaligned.h4
-rw-r--r--arch/mips/kernel/kspd.c33
-rw-r--r--arch/mips/kernel/rtlx.c15
-rw-r--r--arch/mips/kernel/smp.c14
-rw-r--r--arch/mips/kernel/smtc.c5
-rw-r--r--arch/mips/kernel/vpe.c77
-rw-r--r--arch/mips/mm/sc-mips.c5
-rw-r--r--arch/mips/oprofile/op_model_loongson2.c14
-rw-r--r--arch/mips/pci/ops-pmcmsp.c5
-rw-r--r--arch/mips/sgi-ip27/ip27-smp.c2
-rw-r--r--arch/mips/sibyte/bcm1480/irq.c4
-rw-r--r--arch/mips/sibyte/common/sb_tbprof.c33
-rw-r--r--arch/mips/sibyte/swarm/setup.c2
-rw-r--r--drivers/pcmcia/Kconfig4
-rw-r--r--drivers/pcmcia/Makefile1
-rw-r--r--drivers/pcmcia/bcm63xx_pcmcia.c536
-rw-r--r--drivers/pcmcia/bcm63xx_pcmcia.h60
-rw-r--r--drivers/serial/Kconfig19
-rw-r--r--drivers/serial/Makefile1
-rw-r--r--drivers/serial/bcm63xx_uart.c890
-rw-r--r--include/linux/serial_core.h3
30 files changed, 1852 insertions, 114 deletions
diff --git a/arch/mips/alchemy/common/dbdma.c b/arch/mips/alchemy/common/dbdma.c
index 3ab6d80d150..19c1c82849f 100644
--- a/arch/mips/alchemy/common/dbdma.c
+++ b/arch/mips/alchemy/common/dbdma.c
@@ -175,7 +175,7 @@ static dbdev_tab_t dbdev_tab[] = {
#define DBDEV_TAB_SIZE ARRAY_SIZE(dbdev_tab)
#ifdef CONFIG_PM
-static u32 au1xxx_dbdma_pm_regs[NUM_DBDMA_CHANS + 1][8];
+static u32 au1xxx_dbdma_pm_regs[NUM_DBDMA_CHANS + 1][6];
#endif
@@ -993,14 +993,13 @@ void au1xxx_dbdma_suspend(void)
au1xxx_dbdma_pm_regs[0][3] = au_readl(addr + 0x0c);
/* save channel configurations */
- for (i = 1, addr = DDMA_CHANNEL_BASE; i < NUM_DBDMA_CHANS; i++) {
+ for (i = 1, addr = DDMA_CHANNEL_BASE; i <= NUM_DBDMA_CHANS; i++) {
au1xxx_dbdma_pm_regs[i][0] = au_readl(addr + 0x00);
au1xxx_dbdma_pm_regs[i][1] = au_readl(addr + 0x04);
au1xxx_dbdma_pm_regs[i][2] = au_readl(addr + 0x08);
au1xxx_dbdma_pm_regs[i][3] = au_readl(addr + 0x0c);
au1xxx_dbdma_pm_regs[i][4] = au_readl(addr + 0x10);
au1xxx_dbdma_pm_regs[i][5] = au_readl(addr + 0x14);
- au1xxx_dbdma_pm_regs[i][6] = au_readl(addr + 0x18);
/* halt channel */
au_writel(au1xxx_dbdma_pm_regs[i][0] & ~1, addr + 0x00);
@@ -1027,14 +1026,13 @@ void au1xxx_dbdma_resume(void)
au_writel(au1xxx_dbdma_pm_regs[0][3], addr + 0x0c);
/* restore channel configurations */
- for (i = 1, addr = DDMA_CHANNEL_BASE; i < NUM_DBDMA_CHANS; i++) {
+ for (i = 1, addr = DDMA_CHANNEL_BASE; i <= NUM_DBDMA_CHANS; i++) {
au_writel(au1xxx_dbdma_pm_regs[i][0], addr + 0x00);
au_writel(au1xxx_dbdma_pm_regs[i][1], addr + 0x04);
au_writel(au1xxx_dbdma_pm_regs[i][2], addr + 0x08);
au_writel(au1xxx_dbdma_pm_regs[i][3], addr + 0x0c);
au_writel(au1xxx_dbdma_pm_regs[i][4], addr + 0x10);
au_writel(au1xxx_dbdma_pm_regs[i][5], addr + 0x14);
- au_writel(au1xxx_dbdma_pm_regs[i][6], addr + 0x18);
au_sync();
addr += 0x100; /* next channel base */
}
diff --git a/arch/mips/basler/excite/excite_iodev.c b/arch/mips/basler/excite/excite_iodev.c
index dfbfd7e2ac0..938b1d0b765 100644
--- a/arch/mips/basler/excite/excite_iodev.c
+++ b/arch/mips/basler/excite/excite_iodev.c
@@ -112,10 +112,8 @@ static int iodev_open(struct inode *i, struct file *f)
{
int ret;
- lock_kernel();
ret = request_irq(iodev_irq, iodev_irqhdl, IRQF_DISABLED,
iodev_name, &miscdev);
- unlock_kernel();
return ret;
}
diff --git a/arch/mips/bcm63xx/Makefile b/arch/mips/bcm63xx/Makefile
index aaa585cf26e..c146d1edede 100644
--- a/arch/mips/bcm63xx/Makefile
+++ b/arch/mips/bcm63xx/Makefile
@@ -1,5 +1,5 @@
obj-y += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
- dev-dsp.o dev-enet.o
+ dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o
obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
obj-y += boards/
diff --git a/arch/mips/bcm63xx/boards/board_bcm963xx.c b/arch/mips/bcm63xx/boards/board_bcm963xx.c
index fd77f548207..78e155d21be 100644
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -20,10 +20,11 @@
#include <bcm63xx_cpu.h>
#include <bcm63xx_regs.h>
#include <bcm63xx_io.h>
-#include <bcm63xx_board.h>
#include <bcm63xx_dev_pci.h>
#include <bcm63xx_dev_enet.h>
#include <bcm63xx_dev_dsp.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_dev_uart.h>
#include <board_bcm963xx.h>
#define PFX "board_bcm963xx: "
@@ -793,6 +794,11 @@ int __init board_register_devices(void)
{
u32 val;
+ bcm63xx_uart_register();
+
+ if (board.has_pccard)
+ bcm63xx_pcmcia_register();
+
if (board.has_enet0 &&
!board_get_mac_address(board.enet0.mac_addr))
bcm63xx_enet_register(0, &board.enet0);
diff --git a/arch/mips/bcm63xx/dev-pcmcia.c b/arch/mips/bcm63xx/dev-pcmcia.c
new file mode 100644
index 00000000000..de4d917fd54
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-pcmcia.c
@@ -0,0 +1,144 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cs.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+static struct resource pcmcia_resources[] = {
+ /* pcmcia registers */
+ {
+ /* start & end filled at runtime */
+ .flags = IORESOURCE_MEM,
+ },
+
+ /* pcmcia memory zone resources */
+ {
+ .start = BCM_PCMCIA_COMMON_BASE_PA,
+ .end = BCM_PCMCIA_COMMON_END_PA,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = BCM_PCMCIA_ATTR_BASE_PA,
+ .end = BCM_PCMCIA_ATTR_END_PA,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = BCM_PCMCIA_IO_BASE_PA,
+ .end = BCM_PCMCIA_IO_END_PA,
+ .flags = IORESOURCE_MEM,
+ },
+
+ /* PCMCIA irq */
+ {
+ /* start filled at runtime */
+ .flags = IORESOURCE_IRQ,
+ },
+
+ /* declare PCMCIA IO resource also */
+ {
+ .start = BCM_PCMCIA_IO_BASE_PA,
+ .end = BCM_PCMCIA_IO_END_PA,
+ .flags = IORESOURCE_IO,
+ },
+};
+
+static struct bcm63xx_pcmcia_platform_data pd;
+
+static struct platform_device bcm63xx_pcmcia_device = {
+ .name = "bcm63xx_pcmcia",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(pcmcia_resources),
+ .resource = pcmcia_resources,
+ .dev = {
+ .platform_data = &pd,
+ },
+};
+
+static int __init config_pcmcia_cs(unsigned int cs,
+ u32 base, unsigned int size)
+{
+ int ret;
+
+ ret = bcm63xx_set_cs_status(cs, 0);
+ if (!ret)
+ ret = bcm63xx_set_cs_base(cs, base, size);
+ if (!ret)
+ ret = bcm63xx_set_cs_status(cs, 1);
+ return ret;
+}
+
+static const __initdata struct {
+ unsigned int cs;
+ unsigned int base;
+ unsigned int size;
+} pcmcia_cs[3] = {
+ {
+ .cs = MPI_CS_PCMCIA_COMMON,
+ .base = BCM_PCMCIA_COMMON_BASE_PA,
+ .size = BCM_PCMCIA_COMMON_SIZE
+ },
+ {
+ .cs = MPI_CS_PCMCIA_ATTR,
+ .base = BCM_PCMCIA_ATTR_BASE_PA,
+ .size = BCM_PCMCIA_ATTR_SIZE
+ },
+ {
+ .cs = MPI_CS_PCMCIA_IO,
+ .base = BCM_PCMCIA_IO_BASE_PA,
+ .size = BCM_PCMCIA_IO_SIZE
+ },
+};
+
+int __init bcm63xx_pcmcia_register(void)
+{
+ int ret, i;
+
+ if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358())
+ return 0;
+
+ /* use correct pcmcia ready gpio depending on processor */
+ switch (bcm63xx_get_cpu_id()) {
+ case BCM6348_CPU_ID:
+ pd.ready_gpio = 22;
+ break;
+
+ case BCM6358_CPU_ID:
+ pd.ready_gpio = 18;
+ break;
+
+ default:
+ return -ENODEV;
+ }
+
+ pcmcia_resources[0].start = bcm63xx_regset_address(RSET_PCMCIA);
+ pcmcia_resources[0].end = pcmcia_resources[0].start +
+ RSET_PCMCIA_SIZE - 1;
+ pcmcia_resources[4].start = bcm63xx_get_irq_number(IRQ_PCMCIA);
+
+ /* configure pcmcia chip selects */
+ for (i = 0; i < 3; i++) {
+ ret = config_pcmcia_cs(pcmcia_cs[i].cs,
+ pcmcia_cs[i].base,
+ pcmcia_cs[i].size);
+ if (ret)
+ goto out_err;
+ }
+
+ return platform_device_register(&bcm63xx_pcmcia_device);
+
+out_err:
+ printk(KERN_ERR "unable to set pcmcia chip select\n");
+ return ret;
+}
diff --git a/arch/mips/bcm63xx/dev-uart.c b/arch/mips/bcm63xx/dev-uart.c
new file mode 100644
index 00000000000..5f3d89c4a98
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-uart.c
@@ -0,0 +1,41 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_uart.h>
+
+static struct resource uart_resources[] = {
+ {
+ .start = -1, /* filled at runtime */
+ .end = -1, /* filled at runtime */
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = -1, /* filled at runtime */
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bcm63xx_uart_device = {
+ .name = "bcm63xx_uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(uart_resources),
+ .resource = uart_resources,
+};
+
+int __init bcm63xx_uart_register(void)
+{
+ uart_resources[0].start = bcm63xx_regset_address(RSET_UART0);
+ uart_resources[0].end = uart_resources[0].start;
+ uart_resources[0].end += RSET_UART_SIZE - 1;
+ uart_resources[1].start = bcm63xx_get_irq_number(IRQ_UART0);
+ return platform_device_register(&bcm63xx_uart_device);
+}
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h
new file mode 100644
index 00000000000..2beb3969ce3
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h
@@ -0,0 +1,13 @@
+#ifndef BCM63XX_DEV_PCMCIA_H_
+#define BCM63XX_DEV_PCMCIA_H_
+
+/*
+ * PCMCIA driver platform data
+ */
+struct bcm63xx_pcmcia_platform_data {
+ unsigned int ready_gpio;
+};
+
+int bcm63xx_pcmcia_register(void);
+
+#endif /* BCM63XX_DEV_PCMCIA_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h
new file mode 100644
index 00000000000..bf348f573bb
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h
@@ -0,0 +1,6 @@
+#ifndef BCM63XX_DEV_UART_H_
+#define BCM63XX_DEV_UART_H_
+
+int bcm63xx_uart_register(void);
+
+#endif /* BCM63XX_DEV_UART_H_ */
diff --git a/arch/mips/include/asm/smp.h b/arch/mips/include/asm/smp.h
index e15f11a0931..af42385245d 100644
--- a/arch/mips/include/asm/smp.h
+++ b/arch/mips/include/asm/smp.h
@@ -77,7 +77,18 @@ extern void play_dead(void);
extern asmlinkage void smp_call_function_interrupt(void);
-extern void arch_send_call_function_single_ipi(int cpu);
-extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
+static inline void arch_send_call_function_single_ipi(int cpu)
+{
+ extern struct plat_smp_ops *mp_ops; /* private */
+
+ mp_ops->send_ipi_mask(&cpumask_of_cpu(cpu), SMP_CALL_FUNCTION);
+}
+
+static inline void arch_send_call_function_ipi_mask(const struct cpumask *mask)
+{
+ extern struct plat_smp_ops *mp_ops; /* private */
+
+ mp_ops->send_ipi_mask(mask, SMP_CALL_FUNCTION);
+}
#endif /* __ASM_SMP_H */
diff --git a/arch/mips/include/asm/unaligned.h b/arch/mips/include/asm/unaligned.h
index 79240494857..42f66c31147 100644
--- a/arch/mips/include/asm/unaligned.h
+++ b/arch/mips/include/asm/unaligned.h
@@ -12,17 +12,17 @@
#if defined(__MIPSEB__)
# include <linux/unaligned/be_struct.h>
# include <linux/unaligned/le_byteshift.h>
-# include <linux/unaligned/generic.h>
# define get_unaligned __get_unaligned_be
# define put_unaligned __put_unaligned_be
#elif defined(__MIPSEL__)
# include <linux/unaligned/le_struct.h>
# include <linux/unaligned/be_byteshift.h>
-# include <linux/unaligned/generic.h>
# define get_unaligned __get_unaligned_le
# define put_unaligned __put_unaligned_le
#else
# error "MIPS, but neither __MIPSEB__, nor __MIPSEL__???"
#endif
+# include <linux/unaligned/generic.h>
+
#endif /* _ASM_MIPS_UNALIGNED_H */
diff --git a/arch/mips/kernel/kspd.c b/arch/mips/kernel/kspd.c
index f2397f00db4..ad4e017ed2f 100644
--- a/arch/mips/kernel/kspd.c
+++ b/arch/mips/kernel/kspd.c
@@ -172,13 +172,20 @@ static unsigned int translate_open_flags(int flags)
}
-static void sp_setfsuidgid( uid_t uid, gid_t gid)
+static int sp_setfsuidgid(uid_t uid, gid_t gid)
{
- current->cred->fsuid = uid;
- current->cred->fsgid = gid;
+ struct cred *new;
- key_fsuid_changed(current);
- key_fsgid_changed(current);
+ new = prepare_creds();
+ if (!new)
+ return -ENOMEM;
+
+ new->fsuid = uid;
+ new->fsgid = gid;
+
+ commit_creds(new);
+
+ return 0;
}
/*
@@ -196,7 +203,7 @@ void sp_work_handle_request(void)
mm_segment_t old_fs;
struct timeval tv;
struct timezone tz;
- int cmd;
+ int err, cmd;
char *vcwd;
int size;
@@ -225,8 +232,11 @@ void sp_work_handle_request(void)
/* Run the syscall at the privilege of the user who loaded the
SP program */
- if (vpe_getuid(tclimit))
- sp_setfsuidgid(vpe_getuid(tclimit), vpe_getgid(tclimit));
+ if (vpe_getuid(tclimit)) {
+ err = sp_setfsuidgid(vpe_getuid(tclimit), vpe_getgid(tclimit));
+ if (!err)
+ pr_err("Change of creds failed\n");
+ }
switch (sc.cmd) {
/* needs the flags argument translating from SDE kit to
@@ -283,8 +293,11 @@ void sp_work_handle_request(void)
break;
} /* switch */
- if (vpe_getuid(tclimit))
- sp_setfsuidgid( 0, 0);
+ if (vpe_getuid(tclimit)) {
+ err = sp_setfsuidgid(0, 0);
+ if (!err)
+ pr_err("restoring old creds failed\n");
+ }
old_fs = get_fs();
set_fs(KERNEL_DS);
diff --git a/arch/mips/kernel/rtlx.c b/arch/mips/kernel/rtlx.c
index a10ebfdc28a..364f066cb49 100644
--- a/arch/mips/kernel/rtlx.c
+++ b/arch/mips/kernel/rtlx.c
@@ -72,8 +72,9 @@ static void rtlx_dispatch(void)
*/
static irqreturn_t rtlx_interrupt(int irq, void *dev_id)
{
+ unsigned int vpeflags;
+ unsigned long flags;
int i;
- unsigned int flags, vpeflags;
/* Ought not to be strictly necessary for SMTC builds */
local_irq_save(flags);
@@ -392,20 +393,12 @@ out:
static int file_open(struct inode *inode, struct file *filp)
{
- int minor = iminor(inode);
- int err;
-
- lock_kernel();
- err = rtlx_open(minor, (filp->f_flags & O_NONBLOCK) ? 0 : 1);
- unlock_kernel();
- return err;
+ return rtlx_open(iminor(inode), (filp->f_flags & O_NONBLOCK) ? 0 : 1);
}
static int file_release(struct inode *inode, struct file *filp)
{
- int minor = iminor(inode);
-
- return rtlx_release(minor);
+ return rtlx_release(iminor(inode));
}
static unsigned int file_poll(struct file *file, poll_table * wait)
diff --git a/arch/mips/kernel/smp.c b/arch/mips/kernel/smp.c
index 4eb106c6a3e..e72e6844d13 100644
--- a/arch/mips/kernel/smp.c
+++ b/arch/mips/kernel/smp.c
@@ -32,7 +32,6 @@
#include <linux/cpumask.h>
#include <linux/cpu.h>
#include <linux/err.h>
-#include <linux/smp.h>
#include <asm/atomic.h>
#include <asm/cpu.h>
@@ -128,19 +127,6 @@ asmlinkage __cpuinit void start_secondary(void)
cpu_idle();
}
-void arch_send_call_function_ipi_mask(const struct cpumask *mask)
-{
- mp_ops->send_ipi_mask(mask, SMP_CALL_FUNCTION);
-}
-
-/*
- * We reuse the same vector for the single IPI
- */
-void arch_send_call_function_single_ipi(int cpu)
-{
- mp_ops->send_ipi_mask(cpumask_of_cpu(cpu), SMP_CALL_FUNCTION);
-}
-
/*
* Call into both interrupt handlers, as we share the IPI for them
*/
diff --git a/arch/mips/kernel/smtc.c b/arch/mips/kernel/smtc.c
index 67153a0dc26..4d181df44a4 100644
--- a/arch/mips/kernel/smtc.c
+++ b/arch/mips/kernel/smtc.c
@@ -1098,9 +1098,8 @@ static void ipi_irq_dispatch(void)
static struct irqaction irq_ipi = {
.handler = ipi_interrupt,
- .flags = IRQF_DISABLED,
- .name = "SMTC_IPI",
- .flags = IRQF_PERCPU
+ .flags = IRQF_DISABLED | IRQF_PERCPU,
+ .name = "SMTC_IPI"
};
static void setup_cross_vpe_interrupts(unsigned int nvpe)
diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c
index eb6c4c5b7fb..03092ab2a29 100644
--- a/arch/mips/kernel/vpe.c
+++ b/arch/mips/kernel/vpe.c
@@ -144,14 +144,15 @@ struct tc {
};
struct {
- /* Virtual processing elements */
- struct list_head vpe_list;
-
- /* Thread contexts */
- struct list_head tc_list;
+ spinlock_t vpe_list_lock;
+ struct list_head vpe_list; /* Virtual processing elements */
+ spinlock_t tc_list_lock;
+ struct list_head tc_list; /* Thread contexts */
} vpecontrol = {
- .vpe_list = LIST_HEAD_INIT(vpecontrol.vpe_list),
- .tc_list = LIST_HEAD_INIT(vpecontrol.tc_list)
+ .vpe_list_lock = SPIN_LOCK_UNLOCKED,
+ .vpe_list = LIST_HEAD_INIT(vpecontrol.vpe_list),
+ .tc_list_lock = SPIN_LOCK_UNLOCKED,
+ .tc_list = LIST_HEAD_INIT(vpecontrol.tc_list)
};
static void release_progmem(void *ptr);
@@ -159,28 +160,38 @@ static void release_progmem(void *ptr);
/* get the vpe associated with this minor */
static struct vpe *get_vpe(int minor)
{
- struct vpe *v;
+ struct vpe *res, *v;
if (!cpu_has_mipsmt)
return NULL;
+ res = NULL;
+ spin_lock(&vpecontrol.vpe_list_lock);
list_for_each_entry(v, &vpecontrol.vpe_list, list) {
- if (v->minor == minor)
- return v;
+ if (v->minor == minor) {
+ res = v;
+ break;
+ }
}
+ spin_unlock(&vpecontrol.vpe_list_lock);
- return NULL;
+ return res;
}
/* get the vpe associated with this minor */
static struct tc *get_tc(int index)
{
- struct tc *t;
+ struct tc *res, *t;
+ res = NULL;
+ spin_lock(&vpecontrol.tc_list_lock);
list_for_each_entry(t, &vpecontrol.tc_list, list) {
- if (t->index == index)
- return t;
+ if (t->index == index) {
+ res = t;
+ break;
+ }
}
+ spin_unlock(&vpecontrol.tc_list_lock);
return NULL;
}
@@ -190,15 +201,17 @@ static struct vpe *alloc_vpe(int minor)
{
struct vpe *v;
- if ((v = kzalloc(sizeof(struct vpe), GFP_KERNEL)) == NULL) {
+ if ((v = kzalloc(sizeof(struct vpe), GFP_KERNEL)) == NULL)
return NULL;
- }
INIT_LIST_HEAD(&v->tc);
+ spin_lock(&vpecontrol.vpe_list_lock);
list_add_tail(&v->list, &vpecontrol.vpe_list);
+ spin_unlock(&vpecontrol.vpe_list_lock);
INIT_LIST_HEAD(&v->notify);
v->minor = minor;
+
return v;
}
@@ -212,7 +225,10 @@ static struct tc *alloc_tc(int index)
INIT_LIST_HEAD(&tc->tc);
tc->index = index;
+
+ spin_lock(&vpecontrol.tc_list_lock);
list_add_tail(&tc->list, &vpecontrol.tc_list);
+ spin_unlock(&vpecontrol.tc_list_lock);
out:
return tc;
@@ -227,7 +243,7 @@ static void release_vpe(struct vpe *v)
kfree(v);
}
-static void dump_mtregs(void)
+static void __maybe_unused dump_mtregs(void)
{
unsigned long val;
@@ -1048,20 +1064,19 @@ static int vpe_open(struct inode *inode, struct file *filp)
enum vpe_state state;
struct vpe_notifications *not;
struct vpe *v;
- int ret, err = 0;
+ int ret;
- lock_kernel();
if (minor != iminor(inode)) {
/* assume only 1 device at the moment. */
- printk(KERN_WARNING "VPE loader: only vpe1 is supported\n");
- err = -ENODEV;
- goto out;
+ pr_warning("VPE loader: only vpe1 is supported\n");
+
+ return -ENODEV;
}
if ((v = get_vpe(tclimit)) == NULL) {
- printk(KERN_WARNING "VPE loader: unable to get vpe\n");
- err = -ENODEV;
- goto out;
+ pr_warning("VPE loader: unable to get vpe\n");
+
+ return -ENODEV;
}
state = xchg(&v->state, VPE_STATE_INUSE);
@@ -1101,8 +1116,8 @@ static int vpe_open(struct inode *inode, struct file *filp)
v->shared_ptr = NULL;
v->__start = 0;
-out:
unlock_kernel();
+
return 0;
}
@@ -1594,14 +1609,14 @@ static void __exit vpe_module_exit(void)
{
struct vpe *v, *n;
+ device_del(&vpe_device);
+ unregister_chrdev(major, module_name);
+
+ /* No locking needed here */
list_for_each_entry_safe(v, n, &vpecontrol.vpe_list, list) {
- if (v->state != VPE_STATE_UNUSED) {
+ if (v->state != VPE_STATE_UNUSED)
release_vpe(v);
- }
}
-
- device_del(&vpe_device);
- unregister_chrdev(major, module_name);
}
module_init(vpe_module_init);
diff --git a/arch/mips/mm/sc-mips.c b/arch/mips/mm/sc-mips.c
index b55c2d1b998..5ab5fa8c1d8 100644
--- a/arch/mips/mm/sc-mips.c
+++ b/arch/mips/mm/sc-mips.c
@@ -32,6 +32,11 @@ static void mips_sc_wback_inv(unsigned long addr, unsigned long size)
*/
static void mips_sc_inv(unsigned long addr, unsigned long size)
{
+ unsigned long lsize = cpu_scache_line_size();
+ unsigned long almask = ~(lsize - 1);
+
+ cache_op(Hit_Writeback_Inv_SD, addr & almask);
+ cache_op(Hit_Writeback_Inv_SD, (addr + size - 1) & almask);
blast_inv_scache_range(addr, addr + size);
}
diff --git a/arch/mips/oprofile/op_model_loongson2.c b/arch/mips/oprofile/op_model_loongson2.c
index 655cb8dec34..deed1d5d498 100644
--- a/arch/mips/oprofile/op_model_loongson2.c
+++ b/arch/mips/oprofile/op_model_loongson2.c
@@ -44,7 +44,7 @@ static struct loongson2_register_config {
unsigned int ctrl;
unsigned long long reset_counter1;
unsigned long long reset_counter2;
- int cnt1_enalbed, cnt2_enalbed;
+ int cnt1_enabled, cnt2_enabled;
} reg;
DEFINE_SPINLOCK(sample_lock);
@@ -81,8 +81,8 @@ static void loongson2_reg_setup(struct op_counter_config *cfg)
reg.ctrl = ctrl;
- reg.cnt1_enalbed = cfg[0].enabled;
- reg.cnt2_enalbed = cfg[1].enabled;
+ reg.cnt1_enabled = cfg[0].enabled;
+ reg.cnt2_enabled = cfg[1].enabled;
}
@@ -99,7 +99,7 @@ static void loongson2_cpu_setup(void *args)
static void loongson2_cpu_start(void *args)
{
/* Start all counters on current CPU */
- if (reg.cnt1_enalbed || reg.cnt2_enalbed)
+ if (reg.cnt1_enabled || reg.cnt2_enabled)
write_c0_perfctrl(reg.ctrl);
}
@@ -125,7 +125,7 @@ static irqreturn_t loongson2_perfcount_handler(int irq, void *dev_id)
*/
/* Check whether the irq belongs to me */
- enabled = reg.cnt1_enalbed | reg.cnt2_enalbed;
+ enabled = reg.cnt1_enabled | reg.cnt2_enabled;
if (!enabled)
return IRQ_NONE;
@@ -136,12 +136,12 @@ static irqreturn_t loongson2_perfcount_handler(int irq, void *dev_id)
spin_lock_irqsave(&sample_lock, flags);
if (counter1 & LOONGSON2_PERFCNT_OVERFLOW) {
- if (reg.cnt1_enalbed)
+ if (reg.cnt1_enabled)
oprofile_add_sample(regs, 0);
counter1 = reg.reset_counter1;
}
if (counter2 & LOONGSON2_PERFCNT_OVERFLOW) {
- if (reg.cnt2_enalbed)
+ if (reg.cnt2_enabled)
oprofile_add_sample(regs, 1);
counter2 = reg.reset_counter2;
}
diff --git a/arch/mips/pci/ops-pmcmsp.c b/arch/mips/pci/ops-pmcmsp.c
index 109c95ca698..32548b5d68d 100644
--- a/arch/mips/pci/ops-pmcmsp.c
+++ b/arch/mips/pci/ops-pmcmsp.c
@@ -385,6 +385,7 @@ int msp_pcibios_config_access(unsigned char access_type,
unsigned long intr;
unsigned long value;
static char pciirqflag;
+ int ret;
#if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
unsigned int vpe_status;
#endif
@@ -402,11 +403,13 @@ int msp_pcibios_config_access(unsigned char access_type,
* allocation assigns an interrupt handler to the interrupt.
*/
if (pciirqflag == 0) {
- request_irq(MSP_INT_PCI,/* Hardcoded internal MSP7120 wiring */
+ ret = request_irq(MSP_INT_PCI,/* Hardcoded internal MSP7120 wiring */
bpci_interrupt,
IRQF_SHARED | IRQF_DISABLED,
"PMC MSP PCI Host",
preg);
+ if (ret != 0)
+ return ret;
pciirqflag = ~0;
}
diff --git a/arch/mips/sgi-ip27/ip27-smp.c b/arch/mips/sgi-ip27/ip27-smp.c
index 9aa8f2951df..c6851df9ab7 100644
--- a/arch/mips/sgi-ip27/ip27-smp.c
+++ b/arch/mips/sgi-ip27/ip27-smp.c
@@ -165,7 +165,7 @@ static void ip27_send_ipi_single(int destid, unsigned int action)
REMOTE_HUB_SEND_INTR(COMPACT_TO_NASID_NODEID(cpu_to_node(destid)), irq);
}
-static void ip27_send_ipi(const struct cpumask *mask, unsigned int action)
+static void ip27_send_ipi_mask(const struct cpumask *mask, unsigned int action)
{
unsigned int i;
diff --git a/arch/mips/sibyte/bcm1480/irq.c b/arch/mips/sibyte/bcm1480/irq.c
index ba59839a021..4070268aa76 100644
--- a/arch/mips/sibyte/bcm1480/irq.c
+++ b/arch/mips/sibyte/bcm1480/irq.c
@@ -117,10 +117,6 @@ static int bcm1480_set_affinity(unsigned int irq, const struct cpumask *mask)
unsigned long flags;
unsigned int irq_dirty;
- if (cpumask_weight(mask) != 1) {
- printk("attempted to set irq affinity for irq %d to multiple CPUs\n", irq);
- return -1;
- }
i = cpumask_first(mask);
/* Convert logical CPU to physical CPU */
diff --git a/arch/mips/sibyte/common/sb_tbprof.c b/arch/mips/sibyte/common/sb_tbprof.c
index 637a194e5cd..15ea778b5e6 100644
--- a/arch/mips/sibyte/common/sb_tbprof.c
+++ b/arch/mips/sibyte/common/sb_tbprof.c
@@ -403,36 +403,31 @@ static int sbprof_zbprof_stop(void)
static int sbprof_tb_open(struct inode *inode, struct file *filp)
{
int minor;
- int err = 0;
- lock_kernel();
minor = iminor(inode);
- if (minor != 0) {
- err = -ENODEV;
- goto out;
- }
+ if (minor != 0)
+ return -ENODEV;
- if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED) {
- err = -EBUSY;
- goto out;
- }
+ if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED)
+ return -EBUSY;
memset(&sbp, 0, sizeof(struct sbprof_tb));
sbp.sbprof_tbbuf = vmalloc(MAX_TBSAMPLE_BYTES);
if (!sbp.sbprof_tbbuf) {
- err = -ENOMEM;
- goto out;
+ sbp.open = SB_CLOSED;
+ wmb();
+ return -ENOMEM;
}
+
memset(sbp.sbprof_tbbuf, 0, MAX_TBSAMPLE_BYTES);
init_waitqueue_head(&sbp.tb_sync);
init_waitqueue_head(&sbp.tb_read);
mutex_init(&sbp.lock);
sbp.open = SB_OPEN;
+ wmb();
- out:
- unlock_kernel();
- return err;
+ return 0;
}
static int sbprof_tb_release(struct inode *inode, struct file *filp)
@@ -440,7 +435,7 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp)
int minor;
minor = iminor(inode);
- if (minor != 0 || !sbp.open)
+ if (minor != 0 || sbp.open != SB_CLOSED)
return -ENODEV;
mutex_lock(&sbp.lock);
@@ -449,7 +444,8 @@ static int sbprof_tb_release(struct inode *inode, struct file *filp)
sbprof_zbprof_stop();
vfree(sbp.sbprof_tbbuf);
- sbp.open = 0;
+ sbp.open = SB_CLOSED;
+ wmb();
mutex_unlock(&sbp.lock);
@@ -583,7 +579,8 @@ static int __init sbprof_tb_init(void)
}
tb_dev = dev;
- sbp.open = 0;
+ sbp.open = SB_CLOSED;
+ wmb();
tb_period = zbbus_mhz * 10000LL;
pr_info(DEVNAME ": initialized - tb_period = %lld\n",
(long long) tb_period);
diff --git a/arch/mips/sibyte/swarm/setup.c b/arch/mips/sibyte/swarm/setup.c
index 623ffc933c4..5277aac96b0 100644
--- a/arch/mips/sibyte/swarm/setup.c
+++ b/arch/mips/sibyte/swarm/setup.c
@@ -106,7 +106,7 @@ void read_persistent_clock(struct timespec *ts)
break;
}
ts->tv_sec = sec;
- tv->tv_nsec = 0;
+ ts->tv_nsec = 0;
}
int rtc_mips_set_time(unsigned long sec)
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index fbf965b31c1..17f38a781d4 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -192,6 +192,10 @@ config PCMCIA_AU1X00
tristate "Au1x00 pcmcia support"
depends on SOC_AU1X00 && PCMCIA
+config PCMCIA_BCM63XX
+ tristate "bcm63xx pcmcia support"
+ depends on BCM63XX && PCMCIA
+
config PCMCIA_SA1100
tristate "SA1100 support"
depends on ARM && ARCH_SA1100 && PCMCIA
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index 3247828aa20..a03a38acd77 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_PCMCIA_SA1111) += sa11xx_core.o sa1111_cs.o
obj-$(CONFIG_M32R_PCC) += m32r_pcc.o
obj-$(CONFIG_M32R_CFC) += m32r_cfc.o
obj-$(CONFIG_PCMCIA_AU1X00) += au1x00_ss.o
+obj-$(CONFIG_PCMCIA_BCM63XX) += bcm63xx_pcmcia.o
obj-$(CONFIG_PCMCIA_VRC4171) += vrc4171_card.o
obj-$(CONFIG_PCMCIA_VRC4173) += vrc4173_cardu.o
obj-$(CONFIG_OMAP_CF) += omap_cf.o
diff --git a/drivers/pcmcia/bcm63xx_pcmcia.c b/drivers/pcmcia/bcm63xx_pcmcia.c
new file mode 100644
index 00000000000..bc88a3b19bb
--- /dev/null
+++ b/drivers/pcmcia/bcm63xx_pcmcia.c
@@ -0,0 +1,536 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/timer.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/gpio.h>
+
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+#include "bcm63xx_pcmcia.h"
+
+#define PFX "bcm63xx_pcmcia: "
+
+#ifdef CONFIG_CARDBUS
+/* if cardbus is used, platform device needs reference to actual pci
+ * device */
+static struct pci_dev *bcm63xx_cb_dev;
+#endif
+
+/*
+ * read/write helper for pcmcia regs
+ */
+static inline u32 pcmcia_readl(struct bcm63xx_pcmcia_socket *skt, u32 off)
+{
+ return bcm_readl(skt->base + off);
+}
+
+static inline void pcmcia_writel(struct bcm63xx_pcmcia_socket *skt,
+ u32 val, u32 off)
+{
+ bcm_writel(val, skt->base + off);
+}
+
+/*
+ * This callback should (re-)initialise the socket, turn on status
+ * interrupts and PCMCIA bus, and wait for power to stabilise so that
+ * the card status signals report correctly.
+ *
+ * Hardware cannot do that.
+ */
+static int bcm63xx_pcmcia_sock_init(struct pcmcia_socket *sock)
+{
+ return 0;
+}
+
+/*
+ * This callback should remove power on the socket, disable IRQs from
+ * the card, turn off status interrupts, and disable the PCMCIA bus.
+ *
+ * Hardware cannot do that.
+ */
+static int bcm63xx_pcmcia_suspend(struct pcmcia_socket *sock)
+{
+ return 0;
+}
+
+/*
+ * Implements the set_socket() operation for the in-kernel PCMCIA
+ * service (formerly SS_SetSocket in Card Services). We more or
+ * less punt all of this work and let the kernel handle the details
+ * of power configuration, reset, &c. We also record the value of
+ * `state' in order to regurgitate it to the PCMCIA core later.
+ */
+static int bcm63xx_pcmcia_set_socket(struct pcmcia_socket *sock,
+ socket_state_t *state)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ unsigned long flags;
+ u32 val;
+
+ skt = sock->driver_data;
+
+ spin_lock_irqsave(&skt->lock, flags);
+
+ /* note: hardware cannot control socket power, so we will
+ * always report SS_POWERON */
+
+ /* apply socket reset */
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ if (state->flags & SS_RESET)
+ val |= PCMCIA_C1_RESET_MASK;
+ else
+ val &= ~PCMCIA_C1_RESET_MASK;
+
+ /* reverse reset logic for cardbus card */
+ if (skt->card_detected && (skt->card_type & CARD_CARDBUS))
+ val ^= PCMCIA_C1_RESET_MASK;
+
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* keep requested state for event reporting */
+ skt->requested_state = *state;
+
+ spin_unlock_irqrestore(&skt->lock, flags);
+
+ return 0;
+}
+
+/*
+ * identity cardtype from VS[12] input, CD[12] input while only VS2 is
+ * floating, and CD[12] input while only VS1 is floating
+ */
+enum {
+ IN_VS1 = (1 << 0),
+ IN_VS2 = (1 << 1),
+ IN_CD1_VS2H = (1 << 2),
+ IN_CD2_VS2H = (1 << 3),
+ IN_CD1_VS1H = (1 << 4),
+ IN_CD2_VS1H = (1 << 5),
+};
+
+static const u8 vscd_to_cardtype[] = {
+
+ /* VS1 float, VS2 float */
+ [IN_VS1 | IN_VS2] = (CARD_PCCARD | CARD_5V),
+
+ /* VS1 grounded, VS2 float */
+ [IN_VS2] = (CARD_PCCARD | CARD_5V | CARD_3V),
+
+ /* VS1 grounded, VS2 grounded */
+ [0] = (CARD_PCCARD | CARD_5V | CARD_3V | CARD_XV),
+
+ /* VS1 tied to CD1, VS2 float */
+ [IN_VS1 | IN_VS2 | IN_CD1_VS1H] = (CARD_CARDBUS | CARD_3V),
+
+ /* VS1 grounded, VS2 tied to CD2 */
+ [IN_VS2 | IN_CD2_VS2H] = (CARD_CARDBUS | CARD_3V | CARD_XV),
+
+ /* VS1 tied to CD2, VS2 grounded */
+ [IN_VS1 | IN_CD2_VS1H] = (CARD_CARDBUS | CARD_3V | CARD_XV | CARD_YV),
+
+ /* VS1 float, VS2 grounded */
+ [IN_VS1] = (CARD_PCCARD | CARD_XV),
+
+ /* VS1 float, VS2 tied to CD2 */
+ [IN_VS1 | IN_VS2 | IN_CD2_VS2H] = (CARD_CARDBUS | CARD_3V),
+
+ /* VS1 float, VS2 tied to CD1 */
+ [IN_VS1 | IN_VS2 | IN_CD1_VS2H] = (CARD_CARDBUS | CARD_XV | CARD_YV),
+
+ /* VS1 tied to CD2, VS2 float */
+ [IN_VS1 | IN_VS2 | IN_CD2_VS1H] = (CARD_CARDBUS | CARD_YV),
+
+ /* VS2 grounded, VS1 is tied to CD1, CD2 is grounded */
+ [IN_VS1 | IN_CD1_VS1H] = 0, /* ignore cardbay */
+};
+
+/*
+ * poll hardware to check card insertion status
+ */
+static unsigned int __get_socket_status(struct bcm63xx_pcmcia_socket *skt)
+{
+ unsigned int stat;
+ u32 val;
+
+ stat = 0;
+
+ /* check CD for card presence */
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+
+ if (!(val & PCMCIA_C1_CD1_MASK) && !(val & PCMCIA_C1_CD2_MASK))
+ stat |= SS_DETECT;
+
+ /* if new insertion, detect cardtype */
+ if ((stat & SS_DETECT) && !skt->card_detected) {
+ unsigned int stat = 0;
+
+ /* float VS1, float VS2 */
+ val |= PCMCIA_C1_VS1OE_MASK;
+ val |= PCMCIA_C1_VS2OE_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* wait for output to stabilize and read VS[12] */
+ udelay(10);
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ stat |= (val & PCMCIA_C1_VS1_MASK) ? IN_VS1 : 0;
+ stat |= (val & PCMCIA_C1_VS2_MASK) ? IN_VS2 : 0;
+
+ /* drive VS1 low, float VS2 */
+ val &= ~PCMCIA_C1_VS1OE_MASK;
+ val |= PCMCIA_C1_VS2OE_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* wait for output to stabilize and read CD[12] */
+ udelay(10);
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ stat |= (val & PCMCIA_C1_CD1_MASK) ? IN_CD1_VS2H : 0;
+ stat |= (val & PCMCIA_C1_CD2_MASK) ? IN_CD2_VS2H : 0;
+
+ /* float VS1, drive VS2 low */
+ val |= PCMCIA_C1_VS1OE_MASK;
+ val &= ~PCMCIA_C1_VS2OE_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* wait for output to stabilize and read CD[12] */
+ udelay(10);
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ stat |= (val & PCMCIA_C1_CD1_MASK) ? IN_CD1_VS1H : 0;
+ stat |= (val & PCMCIA_C1_CD2_MASK) ? IN_CD2_VS1H : 0;
+
+ /* guess cardtype from all this */
+ skt->card_type = vscd_to_cardtype[stat];
+ if (!skt->card_type)
+ dev_err(&skt->socket.dev, "unsupported card type\n");
+
+ /* drive both VS pin to 0 again */
+ val &= ~(PCMCIA_C1_VS1OE_MASK | PCMCIA_C1_VS2OE_MASK);
+
+ /* enable correct logic */
+ val &= ~(PCMCIA_C1_EN_PCMCIA_MASK | PCMCIA_C1_EN_CARDBUS_MASK);
+ if (skt->card_type & CARD_PCCARD)
+ val |= PCMCIA_C1_EN_PCMCIA_MASK;
+ else
+ val |= PCMCIA_C1_EN_CARDBUS_MASK;
+
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+ }
+ skt->card_detected = (stat & SS_DETECT) ? 1 : 0;
+
+ /* report card type/voltage */
+ if (skt->card_type & CARD_CARDBUS)
+ stat |= SS_CARDBUS;
+ if (skt->card_type & CARD_3V)
+ stat |= SS_3VCARD;
+ if (skt->card_type & CARD_XV)
+ stat |= SS_XVCARD;
+ stat |= SS_POWERON;
+
+ if (gpio_get_value(skt->pd->ready_gpio))
+ stat |= SS_READY;
+
+ return stat;
+}
+
+/*
+ * core request to get current socket status
+ */
+static int bcm63xx_pcmcia_get_status(struct pcmcia_socket *sock,
+ unsigned int *status)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+
+ skt = sock->driver_data;
+
+ spin_lock_bh(&skt->lock);
+ *status = __get_socket_status(skt);
+ spin_unlock_bh(&skt->lock);
+
+ return 0;
+}
+
+/*
+ * socket polling timer callback
+ */
+static void bcm63xx_pcmcia_poll(unsigned long data)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ unsigned int stat, events;
+
+ skt = (struct bcm63xx_pcmcia_socket *)data;
+
+ spin_lock_bh(&skt->lock);
+
+ stat = __get_socket_status(skt);
+
+ /* keep only changed bits, and mask with required one from the
+ * core */
+ events = (stat ^ skt->old_status) & skt->requested_state.csc_mask;
+ skt->old_status = stat;
+ spin_unlock_bh(&skt->lock);
+
+ if (events)
+ pcmcia_parse_events(&skt->socket, events);
+
+ mod_timer(&skt->timer,
+ jiffies + msecs_to_jiffies(BCM63XX_PCMCIA_POLL_RATE));
+}
+
+static int bcm63xx_pcmcia_set_io_map(struct pcmcia_socket *sock,
+ struct pccard_io_map *map)
+{
+ /* this doesn't seem to be called by pcmcia layer if static
+ * mapping is used */
+ return 0;
+}
+
+static int bcm63xx_pcmcia_set_mem_map(struct pcmcia_socket *sock,
+ struct pccard_mem_map *map)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ struct resource *res;
+
+ skt = sock->driver_data;
+ if (map->flags & MAP_ATTRIB)
+ res = skt->attr_res;
+ else
+ res = skt->common_res;
+
+ map->static_start = res->start + map->card_start;
+ return 0;
+}
+
+static struct pccard_operations bcm63xx_pcmcia_operations = {
+ .init = bcm63xx_pcmcia_sock_init,
+ .suspend = bcm63xx_pcmcia_suspend,
+ .get_status = bcm63xx_pcmcia_get_status,
+ .set_socket = bcm63xx_pcmcia_set_socket,
+ .set_io_map = bcm63xx_pcmcia_set_io_map,
+ .set_mem_map = bcm63xx_pcmcia_set_mem_map,
+};
+
+/*
+ * register pcmcia socket to core
+ */
+static int __devinit bcm63xx_drv_pcmcia_probe(struct platform_device *pdev)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ struct pcmcia_socket *sock;
+ struct resource *res, *irq_res;
+ unsigned int regmem_size = 0, iomem_size = 0;
+ u32 val;
+ int ret;
+
+ skt = kzalloc(sizeof(*skt), GFP_KERNEL);
+ if (!skt)
+ return -ENOMEM;
+ spin_lock_init(&skt->lock);
+ sock = &skt->socket;
+ sock->driver_data = skt;
+
+ /* make sure we have all resources we need */
+ skt->common_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ skt->attr_res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ skt->pd = pdev->dev.platform_data;
+ if (!skt->common_res || !skt->attr_res || !irq_res || !skt->pd) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ /* remap pcmcia registers */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ regmem_size = resource_size(res);
+ if (!request_mem_region(res->start, regmem_size, "bcm63xx_pcmcia")) {
+ ret = -EINVAL;
+ goto err;
+ }
+ skt->reg_res = res;
+
+ skt->base = ioremap(res->start, regmem_size);
+ if (!skt->base) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ /* remap io registers */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
+ iomem_size = resource_size(res);
+ skt->io_base = ioremap(res->start, iomem_size);
+ if (!skt->io_base) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ /* resources are static */
+ sock->resource_ops = &pccard_static_ops;
+ sock->ops = &bcm63xx_pcmcia_operations;
+ sock->owner = THIS_MODULE;
+ sock->dev.parent = &pdev->dev;
+ sock->features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
+ sock->io_offset = (unsigned long)skt->io_base;
+ sock->pci_irq = irq_res->start;
+
+#ifdef CONFIG_CARDBUS
+ sock->cb_dev = bcm63xx_cb_dev;
+ if (bcm63xx_cb_dev)
+ sock->features |= SS_CAP_CARDBUS;
+#endif
+
+ /* assume common & attribute memory have the same size */
+ sock->map_size = resource_size(skt->common_res);
+
+ /* initialize polling timer */
+ setup_timer(&skt->timer, bcm63xx_pcmcia_poll, (unsigned long)skt);
+
+ /* initialize pcmcia control register, drive VS[12] to 0,
+ * leave CB IDSEL to the old value since it is set by the PCI
+ * layer */
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ val &= PCMCIA_C1_CBIDSEL_MASK;
+ val |= PCMCIA_C1_EN_PCMCIA_GPIO_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /*
+ * Hardware has only one set of timings registers, not one for
+ * each memory access type, so we configure them for the
+ * slowest one: attribute memory.
+ */
+ val = PCMCIA_C2_DATA16_MASK;
+ val |= 10 << PCMCIA_C2_RWCOUNT_SHIFT;
+ val |= 6 << PCMCIA_C2_INACTIVE_SHIFT;
+ val |= 3 << PCMCIA_C2_SETUP_SHIFT;
+ val |= 3 << PCMCIA_C2_HOLD_SHIFT;
+ pcmcia_writel(skt, val, PCMCIA_C2_REG);
+
+ ret = pcmcia_register_socket(sock);
+ if (ret)
+ goto err;
+
+ /* start polling socket */
+ mod_timer(&skt->timer,
+ jiffies + msecs_to_jiffies(BCM63XX_PCMCIA_POLL_RATE));
+
+ platform_set_drvdata(pdev, skt);
+ return 0;
+
+err:
+ if (skt->io_base)
+ iounmap(skt->io_base);
+ if (skt->base)
+ iounmap(skt->base);
+ if (skt->reg_res)
+ release_mem_region(skt->reg_res->start, regmem_size);
+ kfree(skt);
+ return ret;
+}
+
+static int __devexit bcm63xx_drv_pcmcia_remove(struct platform_device *pdev)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ struct resource *res;
+
+ skt = platform_get_drvdata(pdev);
+ del_timer_sync(&skt->timer);
+ iounmap(skt->base);
+ iounmap(skt->io_base);
+ res = skt->reg_res;
+ release_mem_region(res->start, resource_size(res));
+ kfree(skt);
+ return 0;
+}
+
+struct platform_driver bcm63xx_pcmcia_driver = {
+ .probe = bcm63xx_drv_pcmcia_probe,
+ .remove = __devexit_p(bcm63xx_drv_pcmcia_remove),
+ .driver = {
+ .name = "bcm63xx_pcmcia",
+ .owner = THIS_MODULE,
+ },
+};
+
+#ifdef CONFIG_CARDBUS
+static int __devinit bcm63xx_cb_probe(struct pci_dev *dev,
+ const struct pci_device_id *id)
+{
+ /* keep pci device */
+ bcm63xx_cb_dev = dev;
+ return platform_driver_register(&bcm63xx_pcmcia_driver);
+}
+
+static void __devexit bcm63xx_cb_exit(struct pci_dev *dev)
+{
+ platform_driver_unregister(&bcm63xx_pcmcia_driver);
+ bcm63xx_cb_dev = NULL;
+}
+
+static struct pci_device_id bcm63xx_cb_table[] = {
+ {
+ .vendor = PCI_VENDOR_ID_BROADCOM,
+ .device = BCM6348_CPU_ID,
+ .subvendor = PCI_VENDOR_ID_BROADCOM,
+ .subdevice = PCI_ANY_ID,
+ .class = PCI_CLASS_BRIDGE_CARDBUS << 8,
+ .class_mask = ~0,
+ },
+
+ {
+ .vendor = PCI_VENDOR_ID_BROADCOM,
+ .device = BCM6358_CPU_ID,
+ .subvendor = PCI_VENDOR_ID_BROADCOM,
+ .subdevice = PCI_ANY_ID,
+ .class = PCI_CLASS_BRIDGE_CARDBUS << 8,
+ .class_mask = ~0,
+ },
+
+ { },
+};
+
+MODULE_DEVICE_TABLE(pci, bcm63xx_cb_table);
+
+static struct pci_driver bcm63xx_cardbus_driver = {
+ .name = "bcm63xx_cardbus",
+ .id_table = bcm63xx_cb_table,
+ .probe = bcm63xx_cb_probe,
+ .remove = __devexit_p(bcm63xx_cb_exit),
+};
+#endif
+
+/*
+ * if cardbus support is enabled, register our platform device after
+ * our fake cardbus bridge has been registered
+ */
+static int __init bcm63xx_pcmcia_init(void)
+{
+#ifdef CONFIG_CARDBUS
+ return pci_register_driver(&bcm63xx_cardbus_driver);
+#else
+ return platform_driver_register(&bcm63xx_pcmcia_driver);
+#endif
+}
+
+static void __exit bcm63xx_pcmcia_exit(void)
+{
+#ifdef CONFIG_CARDBUS
+ return pci_unregister_driver(&bcm63xx_cardbus_driver);
+#else
+ platform_driver_unregister(&bcm63xx_pcmcia_driver);
+#endif
+}
+
+module_init(bcm63xx_pcmcia_init);
+module_exit(bcm63xx_pcmcia_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
+MODULE_DESCRIPTION("Linux PCMCIA Card Services: bcm63xx Socket Controller");
diff --git a/drivers/pcmcia/bcm63xx_pcmcia.h b/drivers/pcmcia/bcm63xx_pcmcia.h
new file mode 100644
index 00000000000..ed957399d86
--- /dev/null
+++ b/drivers/pcmcia/bcm63xx_pcmcia.h
@@ -0,0 +1,60 @@
+#ifndef BCM63XX_PCMCIA_H_
+#define BCM63XX_PCMCIA_H_
+
+#include <linux/types.h>
+#include <linux/timer.h>
+#include <pcmcia/ss.h>
+#include <bcm63xx_dev_pcmcia.h>
+
+/* socket polling rate in ms */
+#define BCM63XX_PCMCIA_POLL_RATE 500
+
+enum {
+ CARD_CARDBUS = (1 << 0),
+ CARD_PCCARD = (1 << 1),
+ CARD_5V = (1 << 2),
+ CARD_3V = (1 << 3),
+ CARD_XV = (1 << 4),
+ CARD_YV = (1 << 5),
+};
+
+struct bcm63xx_pcmcia_socket {
+ struct pcmcia_socket socket;
+
+ /* platform specific data */
+ struct bcm63xx_pcmcia_platform_data *pd;
+
+ /* all regs access are protected by this spinlock */
+ spinlock_t lock;
+
+ /* pcmcia registers resource */
+ struct resource *reg_res;
+
+ /* base remapped address of registers */
+ void __iomem *base;
+
+ /* whether a card is detected at the moment */
+ int card_detected;
+
+ /* type of detected card (mask of above enum) */
+ u8 card_type;
+
+ /* keep last socket status to implement event reporting */
+ unsigned int old_status;
+
+ /* backup of requested socket state */
+ socket_state_t requested_state;
+
+ /* timer used for socket status polling */
+ struct timer_list timer;
+
+ /* attribute/common memory resources */
+ struct resource *attr_res;
+ struct resource *common_res;
+ struct resource *io_res;
+
+ /* base address of io memory */
+ void __iomem *io_base;
+};
+
+#endif /* BCM63XX_PCMCIA_H_ */
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 03422ce878c..e70712044a7 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -1458,4 +1458,23 @@ config SERIAL_TIMBERDALE
---help---
Add support for UART controller on timberdale.
+config SERIAL_BCM63XX
+ tristate "bcm63xx serial port support"
+ select SERIAL_CORE
+ depends on BCM63XX
+ help
+ If you have a bcm63xx CPU, you can enable its onboard
+ serial port by enabling this options.
+
+ To compile this driver as a module, choose M here: the
+ module will be called bcm963xx_uart.
+
+config SERIAL_BCM63XX_CONSOLE
+ bool "Console on bcm63xx serial port"
+ depends on SERIAL_BCM63XX=y
+ select SERIAL_CORE_CONSOLE
+ help
+ If you have enabled the serial port on the bcm63xx CPU
+ you can make it the console by answering Y to this option.
+
endmenu
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 97f6fcc8b43..d21d5dd5d04 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
obj-$(CONFIG_SERIAL_PXA) += pxa.o
obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o
obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
diff --git a/drivers/serial/bcm63xx_uart.c b/drivers/serial/bcm63xx_uart.c
new file mode 100644
index 00000000000..beddaa6e906
--- /dev/null
+++ b/drivers/serial/bcm63xx_uart.c
@@ -0,0 +1,890 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from many drivers using generic_serial interface.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ *
+ * Serial driver for BCM63xx integrated UART.
+ *
+ * Hardware flow control was _not_ tested since I only have RX/TX on
+ * my board.
+ */
+
+#if defined(CONFIG_SERIAL_BCM63XX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/console.h>
+#include <linux/clk.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/sysrq.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+
+#include <bcm63xx_clk.h>
+#include <bcm63xx_irq.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+
+#define BCM63XX_NR_UARTS 1
+
+static struct uart_port ports[BCM63XX_NR_UARTS];
+
+/*
+ * rx interrupt mask / stat
+ *
+ * mask:
+ * - rx fifo full
+ * - rx fifo above threshold
+ * - rx fifo not empty for too long
+ */
+#define UART_RX_INT_MASK (UART_IR_MASK(UART_IR_RXOVER) | \
+ UART_IR_MASK(UART_IR_RXTHRESH) | \
+ UART_IR_MASK(UART_IR_RXTIMEOUT))
+
+#define UART_RX_INT_STAT (UART_IR_STAT(UART_IR_RXOVER) | \
+ UART_IR_STAT(UART_IR_RXTHRESH) | \
+ UART_IR_STAT(UART_IR_RXTIMEOUT))
+
+/*
+ * tx interrupt mask / stat
+ *
+ * mask:
+ * - tx fifo empty
+ * - tx fifo below threshold
+ */
+#define UART_TX_INT_MASK (UART_IR_MASK(UART_IR_TXEMPTY) | \
+ UART_IR_MASK(UART_IR_TXTRESH))
+
+#define UART_TX_INT_STAT (UART_IR_STAT(UART_IR_TXEMPTY) | \
+ UART_IR_STAT(UART_IR_TXTRESH))
+
+/*
+ * external input interrupt
+ *
+ * mask: any edge on CTS, DCD
+ */
+#define UART_EXTINP_INT_MASK (UART_EXTINP_IRMASK(UART_EXTINP_IR_CTS) | \
+ UART_EXTINP_IRMASK(UART_EXTINP_IR_DCD))
+
+/*
+ * handy uart register accessor
+ */
+static inline unsigned int bcm_uart_readl(struct uart_port *port,
+ unsigned int offset)
+{
+ return bcm_readl(port->membase + offset);
+}
+
+static inline void bcm_uart_writel(struct uart_port *port,
+ unsigned int value, unsigned int offset)
+{
+ bcm_writel(value, port->membase + offset);
+}
+
+/*
+ * serial core request to check if uart tx fifo is empty
+ */
+static unsigned int bcm_uart_tx_empty(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ return (val & UART_IR_STAT(UART_IR_TXEMPTY)) ? 1 : 0;
+}
+
+/*
+ * serial core request to set RTS and DTR pin state and loopback mode
+ */
+static void bcm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_MCTL_REG);
+ val &= ~(UART_MCTL_DTR_MASK | UART_MCTL_RTS_MASK);
+ /* invert of written value is reflected on the pin */
+ if (!(mctrl & TIOCM_DTR))
+ val |= UART_MCTL_DTR_MASK;
+ if (!(mctrl & TIOCM_RTS))
+ val |= UART_MCTL_RTS_MASK;
+ bcm_uart_writel(port, val, UART_MCTL_REG);
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ if (mctrl & TIOCM_LOOP)
+ val |= UART_CTL_LOOPBACK_MASK;
+ else
+ val &= ~UART_CTL_LOOPBACK_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * serial core request to return RI, CTS, DCD and DSR pin state
+ */
+static unsigned int bcm_uart_get_mctrl(struct uart_port *port)
+{
+ unsigned int val, mctrl;
+
+ mctrl = 0;
+ val = bcm_uart_readl(port, UART_EXTINP_REG);
+ if (val & UART_EXTINP_RI_MASK)
+ mctrl |= TIOCM_RI;
+ if (val & UART_EXTINP_CTS_MASK)
+ mctrl |= TIOCM_CTS;
+ if (val & UART_EXTINP_DCD_MASK)
+ mctrl |= TIOCM_CD;
+ if (val & UART_EXTINP_DSR_MASK)
+ mctrl |= TIOCM_DSR;
+ return mctrl;
+}
+
+/*
+ * serial core request to disable tx ASAP (used for flow control)
+ */
+static void bcm_uart_stop_tx(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val &= ~(UART_CTL_TXEN_MASK);
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val &= ~UART_TX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to (re)enable tx
+ */
+static void bcm_uart_start_tx(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val |= UART_TX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val |= UART_CTL_TXEN_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * serial core request to stop rx, called before port shutdown
+ */
+static void bcm_uart_stop_rx(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val &= ~UART_RX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to enable modem status interrupt reporting
+ */
+static void bcm_uart_enable_ms(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val |= UART_IR_MASK(UART_IR_EXTIP);
+ bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to start/stop emitting break char
+ */
+static void bcm_uart_break_ctl(struct uart_port *port, int ctl)
+{
+ unsigned long flags;
+ unsigned int val;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ if (ctl)
+ val |= UART_CTL_XMITBRK_MASK;
+ else
+ val &= ~UART_CTL_XMITBRK_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * return port type in string format
+ */
+static const char *bcm_uart_type(struct uart_port *port)
+{
+ return (port->type == PORT_BCM63XX) ? "bcm63xx_uart" : NULL;
+}
+
+/*
+ * read all chars in rx fifo and send them to core
+ */
+static void bcm_uart_do_rx(struct uart_port *port)
+{
+ struct tty_struct *tty;
+ unsigned int max_count;
+
+ /* limit number of char read in interrupt, should not be
+ * higher than fifo size anyway since we're much faster than
+ * serial port */
+ max_count = 32;
+ tty = port->info->port.tty;
+ do {
+ unsigned int iestat, c, cstat;
+ char flag;
+
+ /* get overrun/fifo empty information from ier
+ * register */
+ iestat = bcm_uart_readl(port, UART_IR_REG);
+ if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
+ break;
+
+ cstat = c = bcm_uart_readl(port, UART_FIFO_REG);
+ port->icount.rx++;
+ flag = TTY_NORMAL;
+ c &= 0xff;
+
+ if (unlikely((cstat & UART_FIFO_ANYERR_MASK))) {
+ /* do stats first */
+ if (cstat & UART_FIFO_BRKDET_MASK) {
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ continue;
+ }
+
+ if (cstat & UART_FIFO_PARERR_MASK)
+ port->icount.parity++;
+ if (cstat & UART_FIFO_FRAMEERR_MASK)
+ port->icount.frame++;
+
+ /* update flag wrt read_status_mask */
+ cstat &= port->read_status_mask;
+ if (cstat & UART_FIFO_BRKDET_MASK)
+ flag = TTY_BREAK;
+ if (cstat & UART_FIFO_FRAMEERR_MASK)
+ flag = TTY_FRAME;
+ if (cstat & UART_FIFO_PARERR_MASK)
+ flag = TTY_PARITY;
+ }
+
+ if (uart_handle_sysrq_char(port, c))
+ continue;
+
+ if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
+ port->icount.overrun++;
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+ }
+
+ if ((cstat & port->ignore_status_mask) == 0)
+ tty_insert_flip_char(tty, c, flag);
+
+ } while (--max_count);
+
+ tty_flip_buffer_push(tty);
+}
+
+/*
+ * fill tx fifo with chars to send, stop when fifo is about to be full
+ * or when all chars have been sent.
+ */
+static void bcm_uart_do_tx(struct uart_port *port)
+{
+ struct circ_buf *xmit;
+ unsigned int val, max_count;
+
+ if (port->x_char) {
+ bcm_uart_writel(port, port->x_char, UART_FIFO_REG);
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+
+ if (uart_tx_stopped(port)) {
+ bcm_uart_stop_tx(port);
+ return;
+ }
+
+ xmit = &port->info->xmit;
+ if (uart_circ_empty(xmit))
+ goto txq_empty;
+
+ val = bcm_uart_readl(port, UART_MCTL_REG);
+ val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT;
+ max_count = port->fifosize - val;
+
+ while (max_count--) {
+ unsigned int c;
+
+ c = xmit->buf[xmit->tail];
+ bcm_uart_writel(port, c, UART_FIFO_REG);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ goto txq_empty;
+ return;
+
+txq_empty:
+ /* nothing to send, disable transmit interrupt */
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val &= ~UART_TX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+ return;
+}
+
+/*
+ * process uart interrupt
+ */
+static irqreturn_t bcm_uart_interrupt(int irq, void *dev_id)
+{
+ struct uart_port *port;
+ unsigned int irqstat;
+
+ port = dev_id;
+ spin_lock(&port->lock);
+
+ irqstat = bcm_uart_readl(port, UART_IR_REG);
+ if (irqstat & UART_RX_INT_STAT)
+ bcm_uart_do_rx(port);
+
+ if (irqstat & UART_TX_INT_STAT)
+ bcm_uart_do_tx(port);
+
+ if (irqstat & UART_IR_MASK(UART_IR_EXTIP)) {
+ unsigned int estat;
+
+ estat = bcm_uart_readl(port, UART_EXTINP_REG);
+ if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_CTS))
+ uart_handle_cts_change(port,
+ estat & UART_EXTINP_CTS_MASK);
+ if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_DCD))
+ uart_handle_dcd_change(port,
+ estat & UART_EXTINP_DCD_MASK);
+ }
+
+ spin_unlock(&port->lock);
+ return IRQ_HANDLED;
+}
+
+/*
+ * enable rx & tx operation on uart
+ */
+static void bcm_uart_enable(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val |= (UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK | UART_CTL_RXEN_MASK);
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * disable rx & tx operation on uart
+ */
+static void bcm_uart_disable(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val &= ~(UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK |
+ UART_CTL_RXEN_MASK);
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * clear all unread data in rx fifo and unsent data in tx fifo
+ */
+static void bcm_uart_flush(struct uart_port *port)
+{
+ unsigned int val;
+
+ /* empty rx and tx fifo */
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val |= UART_CTL_RSTRXFIFO_MASK | UART_CTL_RSTTXFIFO_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ /* read any pending char to make sure all irq status are
+ * cleared */
+ (void)bcm_uart_readl(port, UART_FIFO_REG);
+}
+
+/*
+ * serial core request to initialize uart and start rx operation
+ */
+static int bcm_uart_startup(struct uart_port *port)
+{
+ unsigned int val;
+ int ret;
+
+ /* mask all irq and flush port */
+ bcm_uart_disable(port);
+ bcm_uart_writel(port, 0, UART_IR_REG);
+ bcm_uart_flush(port);
+
+ /* clear any pending external input interrupt */
+ (void)bcm_uart_readl(port, UART_EXTINP_REG);
+
+ /* set rx/tx fifo thresh to fifo half size */
+ val = bcm_uart_readl(port, UART_MCTL_REG);
+ val &= ~(UART_MCTL_RXFIFOTHRESH_MASK | UART_MCTL_TXFIFOTHRESH_MASK);
+ val |= (port->fifosize / 2) << UART_MCTL_RXFIFOTHRESH_SHIFT;
+ val |= (port->fifosize / 2) << UART_MCTL_TXFIFOTHRESH_SHIFT;
+ bcm_uart_writel(port, val, UART_MCTL_REG);
+
+ /* set rx fifo timeout to 1 char time */
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val &= ~UART_CTL_RXTMOUTCNT_MASK;
+ val |= 1 << UART_CTL_RXTMOUTCNT_SHIFT;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ /* report any edge on dcd and cts */
+ val = UART_EXTINP_INT_MASK;
+ val |= UART_EXTINP_DCD_NOSENSE_MASK;
+ val |= UART_EXTINP_CTS_NOSENSE_MASK;
+ bcm_uart_writel(port, val, UART_EXTINP_REG);
+
+ /* register irq and enable rx interrupts */
+ ret = request_irq(port->irq, bcm_uart_interrupt, 0,
+ bcm_uart_type(port), port);
+ if (ret)
+ return ret;
+ bcm_uart_writel(port, UART_RX_INT_MASK, UART_IR_REG);
+ bcm_uart_enable(port);
+ return 0;
+}
+
+/*
+ * serial core request to flush & disable uart
+ */
+static void bcm_uart_shutdown(struct uart_port *port)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+ bcm_uart_writel(port, 0, UART_IR_REG);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ bcm_uart_disable(port);
+ bcm_uart_flush(port);
+ free_irq(port->irq, port);
+}
+
+/*
+ * serial core request to change current uart setting
+ */
+static void bcm_uart_set_termios(struct uart_port *port,
+ struct ktermios *new,
+ struct ktermios *old)
+{
+ unsigned int ctl, baud, quot, ier;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ /* disable uart while changing speed */
+ bcm_uart_disable(port);
+ bcm_uart_flush(port);
+
+ /* update Control register */
+ ctl = bcm_uart_readl(port, UART_CTL_REG);
+ ctl &= ~UART_CTL_BITSPERSYM_MASK;
+
+ switch (new->c_cflag & CSIZE) {
+ case CS5:
+ ctl |= (0 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ case CS6:
+ ctl |= (1 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ case CS7:
+ ctl |= (2 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ default:
+ ctl |= (3 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ }
+
+ ctl &= ~UART_CTL_STOPBITS_MASK;
+ if (new->c_cflag & CSTOPB)
+ ctl |= UART_CTL_STOPBITS_2;
+ else
+ ctl |= UART_CTL_STOPBITS_1;
+
+ ctl &= ~(UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
+ if (new->c_cflag & PARENB)
+ ctl |= (UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
+ ctl &= ~(UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
+ if (new->c_cflag & PARODD)
+ ctl |= (UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
+ bcm_uart_writel(port, ctl, UART_CTL_REG);
+
+ /* update Baudword register */
+ baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16);
+ quot = uart_get_divisor(port, baud) - 1;
+ bcm_uart_writel(port, quot, UART_BAUD_REG);
+
+ /* update Interrupt register */
+ ier = bcm_uart_readl(port, UART_IR_REG);
+
+ ier &= ~UART_IR_MASK(UART_IR_EXTIP);
+ if (UART_ENABLE_MS(port, new->c_cflag))
+ ier |= UART_IR_MASK(UART_IR_EXTIP);
+
+ bcm_uart_writel(port, ier, UART_IR_REG);
+
+ /* update read/ignore mask */
+ port->read_status_mask = UART_FIFO_VALID_MASK;
+ if (new->c_iflag & INPCK) {
+ port->read_status_mask |= UART_FIFO_FRAMEERR_MASK;
+ port->read_status_mask |= UART_FIFO_PARERR_MASK;
+ }
+ if (new->c_iflag & (BRKINT))
+ port->read_status_mask |= UART_FIFO_BRKDET_MASK;
+
+ port->ignore_status_mask = 0;
+ if (new->c_iflag & IGNPAR)
+ port->ignore_status_mask |= UART_FIFO_PARERR_MASK;
+ if (new->c_iflag & IGNBRK)
+ port->ignore_status_mask |= UART_FIFO_BRKDET_MASK;
+ if (!(new->c_cflag & CREAD))
+ port->ignore_status_mask |= UART_FIFO_VALID_MASK;
+
+ uart_update_timeout(port, new->c_cflag, baud);
+ bcm_uart_enable(port);
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * serial core request to claim uart iomem
+ */
+static int bcm_uart_request_port(struct uart_port *port)
+{
+ unsigned int size;
+
+ size = RSET_UART_SIZE;
+ if (!request_mem_region(port->mapbase, size, "bcm63xx")) {
+ dev_err(port->dev, "Memory region busy\n");
+ return -EBUSY;
+ }
+
+ port->membase = ioremap(port->mapbase, size);
+ if (!port->membase) {
+ dev_err(port->dev, "Unable to map registers\n");
+ release_mem_region(port->mapbase, size);
+ return -EBUSY;
+ }
+ return 0;
+}
+
+/*
+ * serial core request to release uart iomem
+ */
+static void bcm_uart_release_port(struct uart_port *port)
+{
+ release_mem_region(port->mapbase, RSET_UART_SIZE);
+ iounmap(port->membase);
+}
+
+/*
+ * serial core request to do any port required autoconfiguration
+ */
+static void bcm_uart_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ if (bcm_uart_request_port(port))
+ return;
+ port->type = PORT_BCM63XX;
+ }
+}
+
+/*
+ * serial core request to check that port information in serinfo are
+ * suitable
+ */
+static int bcm_uart_verify_port(struct uart_port *port,
+ struct serial_struct *serinfo)
+{
+ if (port->type != PORT_BCM63XX)
+ return -EINVAL;
+ if (port->irq != serinfo->irq)
+ return -EINVAL;
+ if (port->iotype != serinfo->io_type)
+ return -EINVAL;
+ if (port->mapbase != (unsigned long)serinfo->iomem_base)
+ return -EINVAL;
+ return 0;
+}
+
+/* serial core callbacks */
+static struct uart_ops bcm_uart_ops = {
+ .tx_empty = bcm_uart_tx_empty,
+ .get_mctrl = bcm_uart_get_mctrl,
+ .set_mctrl = bcm_uart_set_mctrl,
+ .start_tx = bcm_uart_start_tx,
+ .stop_tx = bcm_uart_stop_tx,
+ .stop_rx = bcm_uart_stop_rx,
+ .enable_ms = bcm_uart_enable_ms,
+ .break_ctl = bcm_uart_break_ctl,
+ .startup = bcm_uart_startup,
+ .shutdown = bcm_uart_shutdown,
+ .set_termios = bcm_uart_set_termios,
+ .type = bcm_uart_type,
+ .release_port = bcm_uart_release_port,
+ .request_port = bcm_uart_request_port,
+ .config_port = bcm_uart_config_port,
+ .verify_port = bcm_uart_verify_port,
+};
+
+
+
+#ifdef CONFIG_SERIAL_BCM63XX_CONSOLE
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+ unsigned int tmout;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ tmout = 10000;
+ while (--tmout) {
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ if (val & UART_IR_STAT(UART_IR_TXEMPTY))
+ break;
+ udelay(1);
+ }
+
+ /* Wait up to 1s for flow control if necessary */
+ if (port->flags & UPF_CONS_FLOW) {
+ tmout = 1000000;
+ while (--tmout) {
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_EXTINP_REG);
+ if (val & UART_EXTINP_CTS_MASK)
+ break;
+ udelay(1);
+ }
+ }
+}
+
+/*
+ * output given char
+ */
+static void bcm_console_putchar(struct uart_port *port, int ch)
+{
+ wait_for_xmitr(port);
+ bcm_uart_writel(port, ch, UART_FIFO_REG);
+}
+
+/*
+ * console core request to output given string
+ */
+static void bcm_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ struct uart_port *port;
+ unsigned long flags;
+ int locked;
+
+ port = &ports[co->index];
+
+ local_irq_save(flags);
+ if (port->sysrq) {
+ /* bcm_uart_interrupt() already took the lock */
+ locked = 0;
+ } else if (oops_in_progress) {
+ locked = spin_trylock(&port->lock);
+ } else {
+ spin_lock(&port->lock);
+ locked = 1;
+ }
+
+ /* call helper to deal with \r\n */
+ uart_console_write(port, s, count, bcm_console_putchar);
+
+ /* and wait for char to be transmitted */
+ wait_for_xmitr(port);
+
+ if (locked)
+ spin_unlock(&port->lock);
+ local_irq_restore(flags);
+}
+
+/*
+ * console core request to setup given console, find matching uart
+ * port and setup it.
+ */
+static int bcm_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index < 0 || co->index >= BCM63XX_NR_UARTS)
+ return -EINVAL;
+ port = &ports[co->index];
+ if (!port->membase)
+ return -ENODEV;
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver bcm_uart_driver;
+
+static struct console bcm63xx_console = {
+ .name = "ttyS",
+ .write = bcm_console_write,
+ .device = uart_console_device,
+ .setup = bcm_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &bcm_uart_driver,
+};
+
+static int __init bcm63xx_console_init(void)
+{
+ register_console(&bcm63xx_console);
+ return 0;
+}
+
+console_initcall(bcm63xx_console_init);
+
+#define BCM63XX_CONSOLE (&bcm63xx_console)
+#else
+#define BCM63XX_CONSOLE NULL
+#endif /* CONFIG_SERIAL_BCM63XX_CONSOLE */
+
+static struct uart_driver bcm_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "bcm63xx_uart",
+ .dev_name = "ttyS",
+ .major = TTY_MAJOR,
+ .minor = 64,
+ .nr = 1,
+ .cons = BCM63XX_CONSOLE,
+};
+
+/*
+ * platform driver probe/remove callback
+ */
+static int __devinit bcm_uart_probe(struct platform_device *pdev)
+{
+ struct resource *res_mem, *res_irq;
+ struct uart_port *port;
+ struct clk *clk;
+ int ret;
+
+ if (pdev->id < 0 || pdev->id >= BCM63XX_NR_UARTS)
+ return -EINVAL;
+
+ if (ports[pdev->id].membase)
+ return -EBUSY;
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!res_irq)
+ return -ENODEV;
+
+ clk = clk_get(&pdev->dev, "periph");
+ if (IS_ERR(clk))
+ return -ENODEV;
+
+ port = &ports[pdev->id];
+ memset(port, 0, sizeof(*port));
+ port->iotype = UPIO_MEM;
+ port->mapbase = res_mem->start;
+ port->irq = res_irq->start;
+ port->ops = &bcm_uart_ops;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->dev = &pdev->dev;
+ port->fifosize = 16;
+ port->uartclk = clk_get_rate(clk) / 2;
+ clk_put(clk);
+
+ ret = uart_add_one_port(&bcm_uart_driver, port);
+ if (ret) {
+ kfree(port);
+ return ret;
+ }
+ platform_set_drvdata(pdev, port);
+ return 0;
+}
+
+static int __devexit bcm_uart_remove(struct platform_device *pdev)
+{
+ struct uart_port *port;
+
+ port = platform_get_drvdata(pdev);
+ uart_remove_one_port(&bcm_uart_driver, port);
+ platform_set_drvdata(pdev, NULL);
+ /* mark port as free */
+ ports[pdev->id].membase = 0;
+ return 0;
+}
+
+/*
+ * platform driver stuff
+ */
+static struct platform_driver bcm_uart_platform_driver = {
+ .probe = bcm_uart_probe,
+ .remove = __devexit_p(bcm_uart_remove),
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "bcm63xx_uart",
+ },
+};
+
+static int __init bcm_uart_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&bcm_uart_driver);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&bcm_uart_platform_driver);
+ if (ret)
+ uart_unregister_driver(&bcm_uart_driver);
+
+ return ret;
+}
+
+static void __exit bcm_uart_exit(void)
+{
+ platform_driver_unregister(&bcm_uart_platform_driver);
+ uart_unregister_driver(&bcm_uart_driver);
+}
+
+module_init(bcm_uart_init);
+module_exit(bcm_uart_exit);
+
+MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
+MODULE_DESCRIPTION("Broadcom 63<xx integrated uart driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index fe661afe071..db532ce288b 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -176,6 +176,9 @@
/* Qualcomm MSM SoCs */
#define PORT_MSM 88
+/* BCM63xx family SoCs */
+#define PORT_BCM63XX 89
+
#ifdef __KERNEL__
#include <linux/compiler.h>