Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
 "These are mostly new device tree bindings for existing drivers, as
  well as changes to the device tree source files to add support for
  those devices, and a couple of new boards, most notably Samsung's
  Exynos5 based Chromebook.

  The changes depend on earlier platform specific updates and touch the
  usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."

* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
  ARM: exynos: dts: cros5250: add EC device
  ARM: dts: Add sbs-battery for exynos5250-snow
  ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
  ARM: dts: add mshc controller node for Exynos4x12 SoCs
  ARM: dts: Add chip-id controller node on Exynos4/5 SoC
  ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
  ARM: davinci: da850-evm: add SPI flash support
  ARM: davinci: da850: override SPI DT node device name
  ARM: davinci: da850: add SPI1 DT node
  spi/davinci: add DT binding documentation
  spi/davinci: no wildcards in DT compatible property
  ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
  ARM: dts: mvebu: introduce internal-regs node
  ARM: dts: mvebu: Convert all the mvebu files to use the range property
  ARM: dts: mvebu: move all peripherals inside soc
  ARM: dts: mvebu: fix cpus section indentation
  ARM: davinci: da850: add EHRPWM & ECAP DT node
  ARM/dts: OMAP3: fix pinctrl-single configuration
  ARM: dts: Add OMAP3430 SDP NOR flash memory binding
  ARM: dts: Add NOR flash bindings for OMAP2420 H4
  ...

1 files changed, 33 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt
index b41e5e52a67..96ec5179c8a 100644
--- a/Documentation/devicetree/bindings/fb/mxsfb.txt
+++ b/Documentation/devicetree/bindings/fb/mxsfb.txt
@@ -5,9 +5,16 @@ Required properties:
   imx23 and imx28.
 - reg: Address and length of the register set for lcdif
 - interrupts: Should contain lcdif interrupts
+- display : phandle to display node (see below for details)
 
-Optional properties:
-- panel-enable-gpios : Should specify the gpio for panel enable
+* display node
+
+Required properties:
+- bits-per-pixel : <16> for RGB565, <32> for RGB888/666.
+- bus-width : number of data lines.  Could be <8>, <16>, <18> or <24>.
+
+Required sub-node:
+- display-timings : Refer to binding doc display-timing.txt for details.
 
 Examples:
 
@@ -15,5 +22,28 @@ lcdif@80030000 {
 	compatible = "fsl,imx28-lcdif";
 	reg = <0x80030000 2000>;
 	interrupts = <38 86>;
-	panel-enable-gpios = <&gpio3 30 0>;
+
+	display: display {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <164>;
+				hback-porch = <89>;
+				hsync-len = <10>;
+				vback-porch = <23>;
+				vfront-porch = <10>;
+				vsync-len = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
 };