Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc device tree conversions (part 2) from Olof Johansson:
 "These continue the device tree work from part 1, this set is for the
  tegra, mxs and imx platforms, all of which have dependencies on clock
  or pinctrl changes submitted earlier."

Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
  ARM: dt: tegra: invert status=disable vs status=okay
  ARM: dt: tegra: consistent basic property ordering
  ARM: dt: tegra: sort nodes based on bus order
  ARM: dt: tegra: remove duplicate device_type property
  ARM: dt: tegra: consistenly use lower-case for hex constants
  ARM: dt: tegra: format regs properties consistently
  ARM: dt: tegra: gpio comment cleanup
  ARM: dt: tegra: remove unnecessary unit addresses
  ARM: dt: tegra: whitespace cleanup
  ARM: dt: tegra cardhu: fix typo in SDHCI node name
  ARM: dt: tegra: cardhu: register core regulator tps62361
  ARM: dt: tegra30.dtsi: Add SMMU node
  ARM: dt: tegra20.dtsi: Add GART node
  ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra: Add device tree support for AHB
  ARM: dts: enable audio support for imx28-evk
  ARM: dts: enable i2c device for imx28-evk
  i2c: mxs: add device tree probe support
  ARM: dts: enable mmc for imx28-evk
  ...

1 files changed, 87 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
new file mode 100644
index 00000000000..0c35673f7a3
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
@@ -0,0 +1,87 @@
+* Freescale MXS GPIO controller
+
+The Freescale MXS GPIO controller is part of MXS PIN controller.  The
+GPIOs are organized in port/bank.  Each port consists of 32 GPIOs.
+
+As the GPIO controller is embedded in the PIN controller and all the
+GPIO ports share the same IO space with PIN controller, the GPIO node
+will be represented as sub-nodes of MXS pinctrl node.
+
+Required properties for GPIO node:
+- compatible : Should be "fsl,<soc>-gpio".  The supported SoCs include
+  imx23 and imx28.
+- interrupts : Should be the port interrupt shared by all 32 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Examples:
+
+aliases {
+	gpio0 = &gpio0;
+	gpio1 = &gpio1;
+	gpio2 = &gpio2;
+	gpio3 = &gpio3;
+	gpio4 = &gpio4;
+};
+
+pinctrl@80018000 {
+	compatible = "fsl,imx28-pinctrl", "simple-bus";
+	reg = <0x80018000 2000>;
+
+	gpio0: gpio@0 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <127>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio1: gpio@1 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <126>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio2: gpio@2 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <125>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio3: gpio@3 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <124>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio4: gpio@4 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <123>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};