Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux

Pull GPIO changes from Grant Likely:
 "The usual selection of bug fixes and driver updates for GPIO.  Nothing
  really stands out except the addition of the GRGPIO driver and some
  enhacements to ACPI support"

I'm pulling this despite the earlier mess.  Let's hope it compiles these
days.

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (46 commits)
  gpio: grgpio: Add irq support
  gpio: grgpio: Add device driver for GRGPIO cores
  gpiolib-acpi: introduce acpi_get_gpio_by_index() helper
  GPIO: gpio-generic: remove kfree() from bgpio_remove call
  gpio / ACPI: Handle ACPI events in accordance with the spec
  gpio: lpc32xx: Fix off-by-one valid range checking for bank
  gpio: mcp23s08: convert driver to DT
  gpio/omap: force restore if context loss is not detectable
  gpio/omap: optimise interrupt service routine
  gpio/omap: remove extra context restores in *_runtime_resume()
  gpio/omap: free irq domain in probe() failure paths
  gpio: gpio-generic: Add 16 and 32 bit big endian byte order support
  gpio: samsung: Add terminating entry for exynos_pinctrl_ids
  gpio: mvebu: add dbg_show function
  MAX7301 GPIO: Do not force SPI speed when using OF Platform
  gpio: gpio-tps65910.c: fix checkpatch error
  gpio: gpio-timberdale.c: fix checkpatch error
  gpio: gpio-tc3589x.c: fix checkpatch errors
  gpio: gpio-stp-xway.c: fix checkpatch error
  gpio: gpio-sch.c: fix checkpatch error
  ...

3 files changed, 78 insertions, 2 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt
new file mode 100644
index 00000000000..e466598105f
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt
@@ -0,0 +1,26 @@
+Aeroflex Gaisler GRGPIO General Purpose I/O cores.
+
+The GRGPIO GPIO core is available in the GRLIB VHDL IP core library.
+
+Note: In the ordinary environment for the GRGPIO core, a Leon SPARC system,
+these properties are built from information in the AMBA plug&play.
+
+Required properties:
+
+- name : Should be "GAISLER_GPIO" or "01_01a"
+
+- reg : Address and length of the register set for the device
+
+- interrupts : Interrupt numbers for this device
+
+Optional properties:
+
+- nbits : The number of gpio lines. If not present driver assumes 32 lines.
+
+- irqmap : An array with an index for each gpio line. An index is either a valid
+	index into the interrupts property array, or 0xffffffff that indicates
+	no irq for that line. Driver provides no interrupt support if not
+	present.
+
+For further information look in the documentation for the GLIB IP core library:
+http://www.gaisler.com/products/grlib/grip.pdf
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
new file mode 100644
index 00000000000..629d0ef1730
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
@@ -0,0 +1,47 @@
+Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for
+8-/16-bit I/O expander with serial interface (I2C/SPI)
+
+Required properties:
+- compatible : Should be
+    - "mcp,mcp23s08" for  8 GPIO SPI version
+    - "mcp,mcp23s17" for 16 GPIO SPI version
+    - "mcp,mcp23008" for  8 GPIO I2C version or
+    - "mcp,mcp23017" for 16 GPIO I2C version of the chip
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify flags. Flags are currently unused.
+- gpio-controller : Marks the device node as a GPIO controller.
+- reg : For an address on its bus. I2C uses this a the I2C address of the chip.
+        SPI uses this to specify the chipselect line which the chip is
+        connected to. The driver and the SPI variant of the chip support
+        multiple chips on the same chipselect. Have a look at
+        mcp,spi-present-mask below.
+
+Required device specific properties (only for SPI chips):
+- mcp,spi-present-mask : This is a present flag, that makes only sense for SPI
+        chips - as the name suggests. Multiple SPI chips can share the same
+        SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a
+        chip connected with the corresponding spi address set. For example if
+        you have a chip with address 3 connected, you have to set bit3 to 1,
+        which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not
+        possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at
+        least one bit to 1 for SPI chips.
+- spi-max-frequency = The maximum frequency this chip is able to handle
+
+Example I2C:
+gpiom1: gpio@20 {
+        compatible = "mcp,mcp23017";
+        gpio-controller;
+        #gpio-cells = <2>;
+        reg = <0x20>;
+};
+
+Example SPI:
+gpiom1: gpio@0 {
+        compatible = "mcp,mcp23s17";
+        gpio-controller;
+        #gpio-cells = <2>;
+        spi-present-mask = <0x01>;
+        reg = <0>;
+        spi-max-frequency = <1000000>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
index bff51a2fee1..1b524c0c79f 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-omap.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
@@ -20,8 +20,11 @@ Required properties:
       8 = active low level-sensitive.
 
 OMAP specific properties:
-- ti,hwmods: Name of the hwmod associated to the GPIO:
-  "gpio<X>", <X> being the 1-based instance number from the HW spec
+- ti,hwmods:		Name of the hwmod associated to the GPIO:
+			"gpio<X>", <X> being the 1-based instance number
+			from the HW spec.
+- ti,gpio-always-on: 	Indicates if a GPIO bank is always powered and
+			so will never lose its logic state.
 
 
 Example: