Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

Pull powerpc updates from Benjamin Herrenschmidt:
 "Some highlights in addition to the usual batch of fixes:

   - 64TB address space support for 64-bit processes by Aneesh Kumar

   - Gavin Shan did a major cleanup & re-organization of our EEH support
     code (IBM fancy PCI error handling & recovery infrastructure) which
     paves the way for supporting different platform backends, along
     with some rework of the PCIe code for the PowerNV platform in order
     to remove home made resource allocations and instead use the
     generic code (which is possible after some small improvements to it
     done by Gavin).

   - Uprobes support by Ananth N Mavinakayanahalli

   - A pile of embedded updates from Freescale folks, including new SoC
     and board supports, more KVM stuff including preparing for 64-bit
     BookE KVM support, ePAPR 1.1 updates, etc..."

Fixup trivial conflicts in drivers/scsi/ipr.c

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
  powerpc/iommu: Fix multiple issues with IOMMU pools code
  powerpc: Fix VMX fix for memcpy case
  driver/mtd:IFC NAND:Initialise internal SRAM before any write
  powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
  powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
  powerpc: Remove tlb batching hack for nighthawk
  powerpc: Set paca->data_offset = 0 for boot cpu
  powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
  powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
  powerpc/mpc85xx: Update interrupt handling for IFC controller
  powerpc/85xx: Enable USB support in p1023rds_defconfig
  powerpc/smp: Do not disable IPI interrupts during suspend
  powerpc/eeh: Fix crash on converting OF node to edev
  powerpc/eeh: Lock module while handling EEH event
  powerpc/kprobe: Don't emulate store when kprobe stwu r1
  powerpc/kprobe: Complete kprobe and migrate exception frame
  powerpc/kprobe: Introduce a new thread flag
  powerpc: Remove unused __get_user64() and __put_user64()
  powerpc/eeh: Global mutex to protect PE tree
  powerpc/eeh: Remove EEH PE for normal PCI hotplug
  ...

1 files changed, 41 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/misc/ifm-csi.txt b/Documentation/devicetree/bindings/misc/ifm-csi.txt
new file mode 100644
index 00000000000..5bdfffb0b9f
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/ifm-csi.txt
@@ -0,0 +1,41 @@
+IFM camera sensor interface on mpc5200 LocalPlus bus
+
+Required properties:
+- compatible: "ifm,o2d-csi"
+- reg: specifies sensor chip select number and associated address range
+- interrupts: external interrupt line number and interrupt sense mode
+  of the interrupt line signaling frame valid events
+- gpios: three gpio-specifiers for "capture", "reset" and "master enable"
+  GPIOs (strictly in this order).
+- ifm,csi-clk-handle: the phandle to a node in the DT describing the sensor
+  clock generator. This node is usually a general purpose timer controller.
+- ifm,csi-addr-bus-width: address bus width (valid values are 16, 24, 25)
+- ifm,csi-data-bus-width: data bus width (valid values are 8 and 16)
+- ifm,csi-wait-cycles: sensor bus wait cycles
+
+Optional properties:
+- ifm,csi-byte-swap: if this property is present, the byte swapping on
+  the bus will be enabled.
+
+Example:
+
+	csi@3,0 {
+		compatible = "ifm,o2d-csi";
+		reg = <3 0 0x00100000>;		/* CS 3, 1 MiB range */
+		interrupts = <1 1 2>;		/* IRQ1, edge falling */
+
+		ifm,csi-clk-handle = <&timer7>;
+		gpios = <&gpio_simple 23 0	/* image_capture */
+			 &gpio_simple 26 0	/* image_reset */
+			 &gpio_simple 29 0>;	/* image_master_en */
+
+		ifm,csi-addr-bus-width = <24>;
+		ifm,csi-data-bus-width = <8>;
+		ifm,csi-wait-cycles = <0>;
+	};
+
+The base address of the used chip select is specified in the
+ranges property of the parent localbus node, for example:
+
+	ranges = <0 0 0xff000000 0x01000000
+		  3 0 0xe3000000 0x00100000>;