Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd

Pull MTD updates from David Woodhouse:
 - Various cleanups especially in NAND tests
 - Add support for NAND flash on BCMA bus
 - DT support for sh_flctl and denali NAND drivers
 - Kill obsolete/superceded drivers (fortunet, nomadik_nand)
 - Fix JFFS2 locking bug in ENOMEM failure path
 - New SPI flash chips, as usual
 - Support writing in 'reliable mode' for DiskOnChip G4
 - Debugfs support in nandsim

* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
  mtd: nand: typo in nand_id_has_period() comments
  mtd: nand/gpio: use io{read,write}*_rep accessors
  mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
  mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
  mtd: nand/docg4: fix and improve read of factory bbt
  mtd: nand/docg4: reserve bb marker area in ecclayout
  mtd: nand/docg4: add support for writing in reliable mode
  mtd: mxc_nand: reorder part_probes to let cmdline override other sources
  mtd: mxc_nand: fix unbalanced clk_disable() in error path
  mtd: nandsim: Introduce debugfs infrastructure
  mtd: physmap_of: error checking to prevent a NULL pointer dereference
  mtg: docg3: potential divide by zero in doc_write_oob()
  mtd: bcm47xxnflash: writing support
  mtd: tests/read: initialize buffer for whole next page
  mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
  mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
  mtd: nand: onfi need to be probed in 8 bits mode
  mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
  mtd: nand: print flash size during detection
  mted: nand_wait_ready timeout fix
  ...

1 files changed, 23 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt
new file mode 100644
index 00000000000..b04d03a1d49
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt
@@ -0,0 +1,23 @@
+* Denali NAND controller
+
+Required properties:
+  - compatible : should be "denali,denali-nand-dt"
+  - reg : should contain registers location and length for data and reg.
+  - reg-names: Should contain the reg names "nand_data" and "denali_reg"
+  - interrupts : The interrupt number.
+  - dm-mask : DMA bit mask
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+nand: nand@ff900000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "denali,denali-nand-dt";
+	reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
+	reg-names = "nand_data", "denali_reg";
+	interrupts = <0 144 4>;
+	dma-mask = <0xffffffff>;
+};