Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:

 1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.

 2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
    Benniston.

 3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
    Mork.

 4) BPF now has a "random" opcode, from Chema Gonzalez.

 5) Add more BPF documentation and improve test framework, from Daniel
    Borkmann.

 6) Support TCP fastopen over ipv6, from Daniel Lee.

 7) Add software TSO helper functions and use them to support software
    TSO in mvneta and mv643xx_eth drivers.  From Ezequiel Garcia.

 8) Support software TSO in fec driver too, from Nimrod Andy.

 9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.

10) Handle broadcasts more gracefully over macvlan when there are large
    numbers of interfaces configured, from Herbert Xu.

11) Allow more control over fwmark used for non-socket based responses,
    from Lorenzo Colitti.

12) Do TCP congestion window limiting based upon measurements, from Neal
    Cardwell.

13) Support busy polling in SCTP, from Neal Horman.

14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.

15) Bridge promisc mode handling improvements from Vlad Yasevich.

16) Don't use inetpeer entries to implement ID generation any more, it
    performs poorly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
  rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
  tcp: fixing TLP's FIN recovery
  net: fec: Add software TSO support
  net: fec: Add Scatter/gather support
  net: fec: Increase buffer descriptor entry number
  net: fec: Factorize feature setting
  net: fec: Enable IP header hardware checksum
  net: fec: Factorize the .xmit transmit function
  bridge: fix compile error when compiling without IPv6 support
  bridge: fix smatch warning / potential null pointer dereference
  via-rhine: fix full-duplex with autoneg disable
  bnx2x: Enlarge the dorq threshold for VFs
  bnx2x: Check for UNDI in uncommon branch
  bnx2x: Fix 1G-baseT link
  bnx2x: Fix link for KR with swapped polarity lane
  sctp: Fix sk_ack_backlog wrap-around problem
  net/core: Add VF link state control policy
  net/fsl: xgmac_mdio is dependent on OF_MDIO
  net/fsl: Make xgmac_mdio read error message useful
  net_sched: drr: warn when qdisc is not work conserving
  ...

1 files changed, 83 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
new file mode 100644
index 00000000000..692076fda0e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
@@ -0,0 +1,83 @@
+Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY
+
+Some boards require special tuning values, particularly when it comes to
+clock delays. You can specify clock delay values by adding
+micrel-specific properties to an Ethernet OF device node.
+
+Note that these settings are applied after any phy-specific fixup from
+phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c),
+and therefore may overwrite them.
+
+KSZ9021:
+
+  All skew control options are specified in picoseconds. The minimum
+  value is 0, the maximum value is 3000, and it is incremented by 200ps
+  steps.
+
+  Optional properties:
+
+    - rxc-skew-ps : Skew control of RXC pad
+    - rxdv-skew-ps : Skew control of RX CTL pad
+    - txc-skew-ps : Skew control of TXC pad
+    - txen-skew-ps : Skew control of TX CTL pad
+    - rxd0-skew-ps : Skew control of RX data 0 pad
+    - rxd1-skew-ps : Skew control of RX data 1 pad
+    - rxd2-skew-ps : Skew control of RX data 2 pad
+    - rxd3-skew-ps : Skew control of RX data 3 pad
+    - txd0-skew-ps : Skew control of TX data 0 pad
+    - txd1-skew-ps : Skew control of TX data 1 pad
+    - txd2-skew-ps : Skew control of TX data 2 pad
+    - txd3-skew-ps : Skew control of TX data 3 pad
+
+KSZ9031:
+
+  All skew control options are specified in picoseconds. The minimum
+  value is 0, and the maximum is property-dependent. The increment
+  step is 60ps.
+
+  Optional properties:
+
+    Maximum value of 1860:
+
+      - rxc-skew-ps : Skew control of RX clock pad
+      - txc-skew-ps : Skew control of TX clock pad
+
+    Maximum value of 900:
+
+      - rxdv-skew-ps : Skew control of RX CTL pad
+      - txen-skew-ps : Skew control of TX CTL pad
+      - rxd0-skew-ps : Skew control of RX data 0 pad
+      - rxd1-skew-ps : Skew control of RX data 1 pad
+      - rxd2-skew-ps : Skew control of RX data 2 pad
+      - rxd3-skew-ps : Skew control of RX data 3 pad
+      - txd0-skew-ps : Skew control of TX data 0 pad
+      - txd1-skew-ps : Skew control of TX data 1 pad
+      - txd2-skew-ps : Skew control of TX data 2 pad
+      - txd3-skew-ps : Skew control of TX data 3 pad
+
+Examples:
+
+	/* Attach to an Ethernet device with autodetected PHY */
+	&enet {
+		rxc-skew-ps = <3000>;
+		rxdv-skew-ps = <0>;
+		txc-skew-ps = <3000>;
+		txen-skew-ps = <0>;
+		status = "okay";
+	};
+
+	/* Attach to an explicitly-specified PHY */
+	mdio {
+		phy0: ethernet-phy@0 {
+			rxc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			txen-skew-ps = <0>;
+			reg = <0>;
+		};
+	};
+	ethernet@70000 {
+		status = "okay";
+		phy = <&phy0>;
+		phy-mode = "rgmii-id";
+	};