Merge remote-tracking branch 'grant/devicetree/next' into for-3.14

5 files changed, 7 insertions, 9 deletions

diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt
index 48b259e29e8..bad381faf03 100644
--- a/Documentation/devicetree/bindings/net/davinci_emac.txt
+++ b/Documentation/devicetree/bindings/net/davinci_emac.txt
@@ -4,7 +4,7 @@ This file provides information, what the device node
 for the davinci_emac interface contains.
 
 Required properties:
-- compatible: "ti,davinci-dm6467-emac";
+- compatible: "ti,davinci-dm6467-emac" or "ti,am3517-emac"
 - reg: Offset and length of the register set for the device
 - ti,davinci-ctrl-reg-offset: offset to control register
 - ti,davinci-ctrl-mod-reg-offset: offset to control module register
diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt
index d5363922140..845ff848d89 100644
--- a/Documentation/devicetree/bindings/net/fsl-fec.txt
+++ b/Documentation/devicetree/bindings/net/fsl-fec.txt
@@ -15,6 +15,7 @@ Optional properties:
   only if property "phy-reset-gpios" is available.  Missing the property
   will have the duration be 1 millisecond.  Numbers greater than 1000 are
   invalid and 1 millisecond will be used instead.
+- phy-supply: regulator that powers the Ethernet PHY.
 
 Example:
 
@@ -25,4 +26,5 @@ ethernet@83fec000 {
 	phy-mode = "mii";
 	phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
 	local-mac-address = [00 04 9F 01 1B B9];
+	phy-supply = <&reg_fec_supply>;
 };
diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt
index a73b79f227e..c233b611424 100644
--- a/Documentation/devicetree/bindings/net/marvell-orion-net.txt
+++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt
@@ -32,7 +32,6 @@ Optional controller properties:
 * Ethernet port node
 
 Required port properties:
- - device_type: shall be "network".
  - compatible: shall be one of "marvell,orion-eth-port",
       "marvell,kirkwood-eth-port".
  - reg: port number relative to ethernet controller, shall be 0, 1, or 2.
@@ -61,7 +60,6 @@ or
 mdio-bus {
 	...
 	ethphy: ethernet-phy@8 {
-		device_type = "ethernet-phy";
 		...
 	};
 };
@@ -75,7 +73,6 @@ eth: ethernet-controller@72000 {
 	marvell,tx-checksum-limit = <1600>;
 
 	ethernet@0 {
-		device_type = "network";
 		compatible = "marvell,orion-eth-port";
 		reg = <0>;
 		interrupts = <29>;
diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index 7cd18fbfcf7..85de6107b98 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -2,7 +2,6 @@ PHY nodes
 
 Required properties:
 
- - device_type : Should be "ethernet-phy"
  - interrupts : <a b> where a is the interrupt number and b is a
    field that represents an encoding of the sense and level
    information for the interrupt.  This should be encoded based on
@@ -11,8 +10,6 @@ Required properties:
  - interrupt-parent : the phandle for the interrupt controller that
    services interrupts for this device.
  - reg : The ID number for the phy, usually a small integer
- - linux,phandle :  phandle for this node; likely referenced by an
-   ethernet controller node.
 
 Optional Properties:
 
@@ -27,9 +24,7 @@ Example:
 
 ethernet-phy@0 {
 	compatible = "ethernet-phy-ieee802.3-c22";
-	linux,phandle = <2452000>;
 	interrupt-parent = <40000>;
 	interrupts = <35 1>;
 	reg = <0>;
-	device_type = "ethernet-phy";
 };
diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt
index 953049b4248..5a41a8658da 100644
--- a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt
+++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt
@@ -8,3 +8,7 @@ Required properties:
 Optional properties:
 - phy-device : phandle to Ethernet phy
 - local-mac-address : Ethernet mac address to use
+- reg-io-width : Mask of sizes (in bytes) of the IO accesses that
+  are supported on the device.  Valid value for SMSC LAN91c111 are
+  1, 2 or 4.  If it's omitted or invalid, the size would be 2 meaning
+  16-bit access only.