Merge tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC late cleanups from Arnd Bergmann:
 "These could not be part of the first cleanup branch, because they
  either came too late in the cycle, or they have dependencies on other
  branches.  Important changes are:

   - The integrator platform is almost multiplatform capable after some
     reorganization (Linus Walleij)
   - Minor cleanups on Zynq (Michal Simek)
   - Lots of changes for Exynos and other Samsung platforms, including
     further preparations for multiplatform support and the clocks
     bindings are rearranged"

* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  devicetree: fix newly added exynos sata bindings
  ARM: EXYNOS: Fix compilation error in cpuidle.c
  ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
  ARM: EXYNOS: Remove hardware.h file
  ARM: SAMSUNG: Remove hardware.h inclusion
  ARM: S3C24XX: Remove invalid code from hardware.h
  dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
  ARM: dts: Keep some essential LDOs enabled for arndale-octa board
  ARM: dts: Disable MDMA1 node for arndale-octa board
  ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
  serial: s3c: Fix build of header without serial_core.h preinclusion
  ARM: EXYNOS: Allow wake-up using GIC interrupts
  ARM: EXYNOS: Stop using legacy Samsung PM code
  ARM: EXYNOS: Remove PM initcalls and useless indirection
  ARM: EXYNOS: Fix abuse of CONFIG_PM
  ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
  ARM: SAMSUNG: Move common save/restore helpers to separate file
  ARM: SAMSUNG: Move Samsung PM debug code into separate file
  ARM: SAMSUNG: Consolidate PM debug functions
  ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
  ...

1 files changed, 40 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index 28f9edb8f19..b422e38946d 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -74,3 +74,43 @@ phy-consumer@12340000 {
 
 Refer to DT bindings documentation of particular PHY consumer devices for more
 information about required PHYs and the way of specification.
+
+Samsung SATA PHY Controller
+---------------------------
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5250-sata-phy"
+- reg : offset and length of the SATA PHY register set;
+- #phy-cells : must be zero
+- clocks : must be exactly one entry
+- clock-names : must be "sata_phyctrl"
+- samsung,exynos-sataphy-i2c-phandle : a phandle to the I2C device, no arguments
+- samsung,syscon-phandle : a phandle to the PMU system controller, no arguments
+
+Example:
+	sata_phy: sata-phy@12170000 {
+		compatible = "samsung,exynos5250-sata-phy";
+		reg = <0x12170000 0x1ff>;
+		clocks = <&clock 287>;
+		clock-names = "sata_phyctrl";
+		#phy-cells = <0>;
+		samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+		samsung,syscon-phandle = <&pmu_syscon>;
+	};
+
+Device-Tree bindings for sataphy i2c client driver
+--------------------------------------------------
+
+Required properties:
+compatible: Should be "samsung,exynos-sataphy-i2c"
+- reg: I2C address of the sataphy i2c device.
+
+Example:
+
+	sata_phy_i2c:sata-phy@38 {
+		compatible = "samsung,exynos-sataphy-i2c";
+		reg = <0x38>;
+	};