Merge tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "Main pin control pull request for the v3.13 cycle.

  The changes hitting arch/blackfin are ACKed by the Blackfin
  maintainer, and the device tree bindings are ACKed to the extent
  possible by someone from the device tree maintainers group.

   - Blackfin ADI pin control driver, we move yet another architecture
     under this subsystem umbrella.

   - Incremental updates to the Renesas Super-H PFC pin control driver.
     New subdriver for the r8a7791 SoC.

   - Non-linear GPIO ranges from the gpiolib side of things, this
     enabled simplified device tree bindings by referring entire groups
     of pins on some pin controller to act as back-end for a certain
     GPIO-chip driver.

   - Add the Abilis TB10x pin control driver used on the ARC
     architecture.  Also the corresponding GPIO driver is merged through
     this tree, so the ARC has full support for pins and GPIOs after
     this.

   - Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
     instances.  The i.MX1 and i.MX27 is an entirely new family
     (silicon) of controllers whereas i.MX50 is a variant of the
     previous supported controller.

   - Then the usual slew of fixes, cleanups and incremental updates"

The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.

* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
  pinctrl: imx50: add pinctrl support code for the IMX50 SoC
  pinctrl: at91: copy define to driver
  pinctrl: remove minor dead code
  pinctrl: imx: fix using pin->input_val wrongly
  pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
  gpio: tb10x: fix return value check in tb10x_gpio_probe()
  gpio: tb10x: use module_platform_driver to simplify the code
  pinctrl: imx27: imx27 pincontrol driver
  pinctrl: imx1 core driver
  pinctrl: sh-pfc: r8a7791 PFC support
  sh-pfc: r8a7778: Add CAN pin groups
  gpio: add TB10x GPIO driver
  pinctrl: at91: correct a few typos
  pinctrl: mvebu: remove redundant of_match_ptr
  pinctrl: tb10x: use module_platform_driver to simplify the code
  pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
  pinctrl: add documentation for pinctrl_get_group_pins()
  pinctrl: rockchip: emulate both edge triggered interrupts
  pinctrl: rockchip: add rk3188 specifics
  pinctrl: rockchip: remove redundant check
  ...

1 files changed, 18 insertions, 19 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
index 3a7caf7a744..9fde25f1401 100644
--- a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
@@ -22,11 +22,12 @@ Required properties for iomux controller:
   Please refer to each fsl,<soc>-pinctrl.txt binding doc for supported SoCs.
 
 Required properties for pin configuration node:
-- fsl,pins: two integers array, represents a group of pins mux and config
-  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
-  pin working on a specific function, which consists of a tuple of
-  <mux_reg conf_reg input_reg mux_val input_val>.  CONFIG is the pad setting
-  value like pull-up on this pin.
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx*-pinfunc.h under device tree source folder. The last integer CONFIG is
+  the pad setting value like pull-up on this pin. And that's why fsl,pins entry
+  looks like <PIN_FUNC_ID CONFIG> in the example below.
 
 Bits used for CONFIG:
 NO_PAD_CTL(1 << 31): indicate this pin does not need config.
@@ -72,17 +73,18 @@ iomuxc@020e0000 {
 	/* shared pinctrl settings */
 	usdhc4 {
 		pinctrl_usdhc4_1: usdhc4grp-1 {
-			fsl,pins = <1386 0x17059	/* MX6Q_PAD_SD4_CMD__USDHC4_CMD */
-				    1392 0x10059	/* MX6Q_PAD_SD4_CLK__USDHC4_CLK	*/
-				    1462 0x17059	/* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */
-				    1470 0x17059	/* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */
-				    1478 0x17059	/* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */
-				    1486 0x17059	/* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */
-				    1493 0x17059	/* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */
-				    1501 0x17059	/* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */
-				    1509 0x17059	/* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */
-				    1517 0x17059>;	/* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */
-		};
+			fsl,pins = <
+				MX6QDL_PAD_SD4_CMD__SD4_CMD    0x17059
+				MX6QDL_PAD_SD4_CLK__SD4_CLK    0x10059
+				MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+				MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+				MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+				MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+				MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+				MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+				MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+				MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+			>;
 	};
 	....
 };
@@ -90,6 +92,3 @@ Refer to the IOMUXC controller chapter in imx6q datasheet,
 0x17059 means enable hysteresis, 47KOhm Pull Up, 50Mhz speed,
 80Ohm driver strength and Fast Slew Rate.
 User should refer to each SoC spec to set the correct value.
-
-TODO: when dtc macro support is available, we can change above raw data
-to dt macro which can get better readability in dts file.