pinctrl: rockchip: add rk3188 specifics

Besides the pull registers sitting in a separate place, the rk3188 also
has the peculiarity that the pull registers of the first bank are split
and the first half is sitting in the register space of the pmu.

Therefore this adds a special bank-type for the first bank, to handle
the two register sources.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1 files changed, 45 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
index b0fb1018d7a..f378d342aae 100644
--- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
@@ -21,10 +21,13 @@ defined as gpio sub-nodes of the pinmux controller.
 Required properties for iomux controller:
   - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl"
 		       "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl"
+  - reg: first element is the general register space of the iomux controller
+	 second element is the separate pull register space of the rk3188
 
 Required properties for gpio sub nodes:
-  - compatible: "rockchip,gpio-bank"
+  - compatible: "rockchip,gpio-bank", "rockchip,rk3188-gpio-bank0"
   - reg: register of the gpio bank (different than the iomux registerset)
+         second element: separate pull register for rk3188 bank0
   - interrupts: base interrupt of the gpio bank in the interrupt controller
   - clocks: clock that drives this bank
   - gpio-controller: identifies the node as a gpio controller and pin bank.
@@ -95,3 +98,44 @@ uart2: serial@20064000 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart2_xfer>;
 };
+
+Example for rk3188:
+
+	pinctrl@20008000 {
+		compatible = "rockchip,rk3188-pinctrl";
+		reg = <0x20008000 0xa0>,
+		      <0x20008164 0x1a0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio0: gpio0@0x2000a000 {
+			compatible = "rockchip,rk3188-gpio-bank0";
+			reg = <0x2000a000 0x100>,
+			      <0x20004064 0x8>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_gates8 9>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio1@0x2003c000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x2003c000 0x100>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_gates8 10>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		...
+
+	};