Merge commit 'v2.6.38-rc8' into spi/next

Conflicts:
	drivers/spi/pxa2xx_spi_pci.c

2 files changed, 110 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt
new file mode 100644
index 00000000000..777abd7399d
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt
@@ -0,0 +1,53 @@
+* SPI (Serial Peripheral Interface)
+
+Required properties:
+- cell-index : QE SPI subblock index.
+		0: QE subblock SPI1
+		1: QE subblock SPI2
+- compatible : should be "fsl,spi".
+- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+  field that represents an encoding of the sense and level
+  information for the interrupt.  This should be encoded based on
+  the information in section 2) depending on the type of interrupt
+  controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+
+Optional properties:
+- gpios : specifies the gpio pins to be used for chipselects.
+  The gpios will be referred to as reg = <index> in the SPI child nodes.
+  If unspecified, a single SPI device without a chip select can be used.
+
+Example:
+	spi@4c0 {
+		cell-index = <0>;
+		compatible = "fsl,spi";
+		reg = <4c0 40>;
+		interrupts = <82 0>;
+		interrupt-parent = <700>;
+		mode = "cpu";
+		gpios = <&gpio 18 1	// device reg=<0>
+			 &gpio 19 1>;	// device reg=<1>
+	};
+
+
+* eSPI (Enhanced Serial Peripheral Interface)
+
+Required properties:
+- compatible : should be "fsl,mpc8536-espi".
+- reg : Offset and length of the register set for the device.
+- interrupts : should contain eSPI interrupt, the device has one interrupt.
+- fsl,espi-num-chipselects : the number of the chipselect signals.
+
+Example:
+	spi@110000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc8536-espi";
+		reg = <0x110000 0x1000>;
+		interrupts = <53 0x2>;
+		interrupt-parent = <&mpic>;
+		fsl,espi-num-chipselects = <4>;
+	};
diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt
new file mode 100644
index 00000000000..e782add2e45
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -0,0 +1,57 @@
+SPI (Serial Peripheral Interface) busses
+
+SPI busses can be described with a node for the SPI master device
+and a set of child nodes for each SPI slave on the bus.  For this
+discussion, it is assumed that the system's SPI controller is in
+SPI master mode.  This binding does not describe SPI controllers
+in slave mode.
+
+The SPI master node requires the following properties:
+- #address-cells  - number of cells required to define a chip select
+    		address on the SPI bus.
+- #size-cells     - should be zero.
+- compatible      - name of SPI bus controller following generic names
+    		recommended practice.
+No other properties are required in the SPI bus node.  It is assumed
+that a driver for an SPI bus device will understand that it is an SPI bus.
+However, the binding does not attempt to define the specific method for
+assigning chip select numbers.  Since SPI chip select configuration is
+flexible and non-standardized, it is left out of this binding with the
+assumption that board specific platform code will be used to manage
+chip selects.  Individual drivers can define additional properties to
+support describing the chip select layout.
+
+SPI slave nodes must be children of the SPI master node and can
+contain the following properties.
+- reg             - (required) chip select address of device.
+- compatible      - (required) name of SPI device following generic names
+    		recommended practice
+- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+- spi-cpol        - (optional) Empty property indicating device requires
+    		inverse clock polarity (CPOL) mode
+- spi-cpha        - (optional) Empty property indicating device requires
+    		shifted clock phase (CPHA) mode
+- spi-cs-high     - (optional) Empty property indicating device requires
+    		chip select active high
+
+SPI example for an MPC5200 SPI bus:
+	spi@f00 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+		reg = <0xf00 0x20>;
+		interrupts = <2 13 0 2 14 0>;
+		interrupt-parent = <&mpc5200_pic>;
+
+		ethernet-switch@0 {
+			compatible = "micrel,ks8995m";
+			spi-max-frequency = <1000000>;
+			reg = <0>;
+		};
+
+		codec@1 {
+			compatible = "ti,tlv320aic26";
+			spi-max-frequency = <100000>;
+			reg = <1>;
+		};
+	};