Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm

Pull ARM updates from Russell King:
 "Included in these updates are:
   - Performance optimisation to avoid writing the control register at
     every exception.
   - Use static inline instead of extern inline in ftrace code.
   - Crypto ARM assembly updates for big endian
   - Alignment of initrd/.init memory to page sizes when freeing to
     ensure that we fully free the regions
   - Add gcov support
   - A couple of preparatory patches for VDSO support: use
     _install_special_mapping, and randomize the sigpage placement above
     stack.
   - Add L2 ePAPR DT cache properties so that DT can specify the cache
     geometry.
   - Preparatory patch for FIQ (NMI) kernel C code for things like
     spinlock lockup debug.  Following on from this are a couple of my
     patches cleaning up show_regs() and removing an unused (probably
     since 1.x days) do_unexp_fiq() function.
   - Use pr_warn() rather than pr_warning().
   - A number of cleanups (smp, footbridge, return_address)"

* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (21 commits)
  ARM: 8167/1: extend the reserved memory for initrd to be page aligned
  ARM: 8168/1: extend __init_end to a page align address
  ARM: 8169/1: l2c: parse cache properties from ePAPR definitions
  ARM: 8160/1: drop warning about return_address not using unwind tables
  ARM: 8161/1: footbridge: select machine dir based on ARCH_FOOTBRIDGE
  ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h
  ARM: 8155/1: place sigpage at a random offset above stack
  ARM: 8154/1: use _install_special_mapping for sigpage
  ARM: 8153/1: Enable gcov support on the ARM architecture
  ARM: Avoid writing to control register on every exception
  ARM: 8152/1: Convert pr_warning to pr_warn
  ARM: remove unused do_unexp_fiq() function
  ARM: remove extraneous newline in show_regs()
  ARM: 8150/3: fiq: Replace default FIQ handler
  ARM: 8140/1: ep93xx: Enable DEBUG_LL_UART_PL01X
  ARM: 8139/1: versatile: Enable DEBUG_LL_UART_PL01X
  ARM: 8138/1: drop ISAR0 workaround for B15
  ARM: 8136/1: sa1100: add Micro ASIC platform device
  ARM: 8131/1: arm/smp: Absorb boot_secondary()
  ARM: 8126/1: crypto: enable NEON SHA-384/SHA-512 for big endian
  ...

1 files changed, 10 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
index af527ee111c..292ef7ca305 100644
--- a/Documentation/devicetree/bindings/arm/l2cc.txt
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -2,6 +2,10 @@
 
 ARM cores often have a separate level 2 cache controller. There are various
 implementations of the L2 cache controller with compatible programming models.
+Some of the properties that are just prefixed "cache-*" are taken from section
+3.7.3 of the ePAPR v1.1 specification which can be found at:
+https://www.power.org/wp-content/uploads/2012/06/Power_ePAPR_APPROVED_v1.1.pdf
+
 The ARM L2 cache representation in the device tree should be done as follows:
 
 Required properties:
@@ -44,6 +48,12 @@ Optional properties:
   I/O coherent mode. Valid only when the arm,pl310-cache compatible
   string is used.
 - interrupts : 1 combined interrupt.
+- cache-size : specifies the size in bytes of the cache
+- cache-sets : specifies the number of associativity sets of the cache
+- cache-block-size : specifies the size in bytes of a cache block
+- cache-line-size : specifies the size in bytes of a line in the cache,
+  if this is not specified, the line size is assumed to be equal to the
+  cache block size
 - cache-id-part: cache id part number to be used if it is not present
   on hardware
 - wt-override: If present then L2 is forced to Write through mode