Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:

 1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.

 2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
    Benniston.

 3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
    Mork.

 4) BPF now has a "random" opcode, from Chema Gonzalez.

 5) Add more BPF documentation and improve test framework, from Daniel
    Borkmann.

 6) Support TCP fastopen over ipv6, from Daniel Lee.

 7) Add software TSO helper functions and use them to support software
    TSO in mvneta and mv643xx_eth drivers.  From Ezequiel Garcia.

 8) Support software TSO in fec driver too, from Nimrod Andy.

 9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.

10) Handle broadcasts more gracefully over macvlan when there are large
    numbers of interfaces configured, from Herbert Xu.

11) Allow more control over fwmark used for non-socket based responses,
    from Lorenzo Colitti.

12) Do TCP congestion window limiting based upon measurements, from Neal
    Cardwell.

13) Support busy polling in SCTP, from Neal Horman.

14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.

15) Bridge promisc mode handling improvements from Vlad Yasevich.

16) Don't use inetpeer entries to implement ID generation any more, it
    performs poorly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
  rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
  tcp: fixing TLP's FIN recovery
  net: fec: Add software TSO support
  net: fec: Add Scatter/gather support
  net: fec: Increase buffer descriptor entry number
  net: fec: Factorize feature setting
  net: fec: Enable IP header hardware checksum
  net: fec: Factorize the .xmit transmit function
  bridge: fix compile error when compiling without IPv6 support
  bridge: fix smatch warning / potential null pointer dereference
  via-rhine: fix full-duplex with autoneg disable
  bnx2x: Enlarge the dorq threshold for VFs
  bnx2x: Check for UNDI in uncommon branch
  bnx2x: Fix 1G-baseT link
  bnx2x: Fix link for KR with swapped polarity lane
  sctp: Fix sk_ack_backlog wrap-around problem
  net/core: Add VF link state control policy
  net/fsl: xgmac_mdio is dependent on OF_MDIO
  net/fsl: Make xgmac_mdio read error message useful
  net_sched: drr: warn when qdisc is not work conserving
  ...

17 files changed, 412 insertions, 58 deletions

diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
new file mode 100644
index 00000000000..d01ed63d3eb
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
@@ -0,0 +1,17 @@
+* AMD 10GbE PHY driver (amd-xgbe-phy)
+
+Required properties:
+- compatible: Should be "amd,xgbe-phy-seattle-v1a" and
+  "ethernet-phy-ieee802.3-c45"
+- reg: Address and length of the register sets for the device
+   - SerDes Rx/Tx registers
+   - SerDes integration registers (1/2)
+   - SerDes integration registers (2/2)
+
+Example:
+	xgbe_phy@e1240800 {
+		compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45";
+		reg = <0 0xe1240800 0 0x00400>,
+		      <0 0xe1250000 0 0x00060>,
+		      <0 0xe1250080 0 0x00004>;
+	};
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt
new file mode 100644
index 00000000000..ea0c7908a3b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt
@@ -0,0 +1,34 @@
+* AMD 10GbE driver (amd-xgbe)
+
+Required properties:
+- compatible: Should be "amd,xgbe-seattle-v1a"
+- reg: Address and length of the register sets for the device
+   - MAC registers
+   - PCS registers
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the amd-xgbe interrupt
+- clocks: Should be the DMA clock for the amd-xgbe device (used for
+  calculating the correct Rx interrupt watchdog timer value on a DMA
+  channel for coalescing)
+- clock-names: Should be the name of the DMA clock, "dma_clk"
+- phy-handle: See ethernet.txt file in the same directory
+- phy-mode: See ethernet.txt file in the same directory
+
+Optional properties:
+- mac-address: mac address to be assigned to the device. Can be overridden
+  by UEFI.
+
+Example:
+	xgbe@e0700000 {
+		compatible = "amd,xgbe-seattle-v1a";
+		reg = <0 0xe0700000 0 0x80000>,
+		      <0 0xe0780000 0 0x80000>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 325 4>;
+		clocks = <&xgbe_clk>;
+		clock-names = "dma_clk";
+		phy-handle = <&phy>;
+		phy-mode = "xgmii";
+		mac-address = [ 02 a1 a2 a3 a4 a5 ];
+	};
diff --git a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt b/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt
index f2febb94550..451fef26b4d 100644
--- a/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt
+++ b/Documentation/devicetree/bindings/net/broadcom-bcmgenet.txt
@@ -24,7 +24,7 @@ Optional properties:
 - fixed-link: When the GENET interface is connected to a MoCA hardware block or
   when operating in a RGMII to RGMII type of connection, or when the MDIO bus is
   voluntarily disabled, this property should be used to describe the "fixed link".
-  See Documentation/devicetree/bindings/net/fsl-tsec-phy.txt for information on
+  See Documentation/devicetree/bindings/net/fixed-link.txt for information on
   the property specifics
 
 Required child nodes:
diff --git a/Documentation/devicetree/bindings/net/broadcom-systemport.txt b/Documentation/devicetree/bindings/net/broadcom-systemport.txt
new file mode 100644
index 00000000000..c183ea90d9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-systemport.txt
@@ -0,0 +1,29 @@
+* Broadcom BCM7xxx Ethernet Systemport Controller (SYSTEMPORT)
+
+Required properties:
+- compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport"
+- reg: address and length of the register set for the device.
+- interrupts: interrupts for the device, first cell must be for the the rx
+  interrupts, and the second cell should be for the transmit queues
+- local-mac-address: Ethernet MAC address (48 bits) of this adapter
+- phy-mode: Should be a string describing the PHY interface to the
+  Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt
+- fixed-link: see Documentation/devicetree/bindings/net/fixed-link.txt for
+  the property specific details
+
+Optional properties:
+- systemport,num-tier2-arb: number of tier 2 arbiters, an integer
+- systemport,num-tier1-arb: number of tier 1 arbiters, an integer
+- systemport,num-txq: number of HW transmit queues, an integer
+- systemport,num-rxq: number of HW receive queues, an integer
+
+Example:
+ethernet@f04a0000 {
+	compatible = "brcm,systemport-v1.00";
+	reg = <0xf04a0000 0x4650>;
+	local-mac-address = [ 00 11 22 33 44 55 ];
+	fixed-link = <0 1 1000 0 0>;
+	phy-mode = "gmii";
+	interrupts = <0x0 0x16 0x0>,
+		<0x0 0x17 0x0>;
+};
diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt
new file mode 100644
index 00000000000..fe38847d8e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt
@@ -0,0 +1,44 @@
+Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings
+---------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,zynq-can-1.0" for Zynq CAN
+			  controllers and "xlnx,axi-can-1.00.a" for Axi CAN
+			  controllers.
+- reg			: Physical base address and size of the Axi CAN/Zynq
+			  CANPS registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- interrupt-parent	: Must be core interrupt controller
+- clock-names		: List of input clock names - "can_clk", "pclk"
+			  (For CANPS), "can_clk" , "s_axi_aclk"(For AXI CAN)
+			  (See clock bindings for details).
+- clocks		: Clock phandles (see clock bindings for details).
+- tx-fifo-depth		: Can Tx fifo depth.
+- rx-fifo-depth		: Can Rx fifo depth.
+
+
+Example:
+
+For Zynq CANPS Dts file:
+	zynq_can_0: can@e0008000 {
+			compatible = "xlnx,zynq-can-1.0";
+			clocks = <&clkc 19>, <&clkc 36>;
+			clock-names = "can_clk", "pclk";
+			reg = <0xe0008000 0x1000>;
+			interrupts = <0 28 4>;
+			interrupt-parent = <&intc>;
+			tx-fifo-depth = <0x40>;
+			rx-fifo-depth = <0x40>;
+		};
+For Axi CAN Dts file:
+	axi_can_0: axi-can@40000000 {
+			compatible = "xlnx,axi-can-1.00.a";
+			clocks = <&clkc 0>, <&clkc 1>;
+			clock-names = "can_clk","s_axi_aclk" ;
+			reg = <0x40000000 0x10000>;
+			interrupt-parent = <&intc>;
+			interrupts = <0 59 1>;
+			tx-fifo-depth = <0x40>;
+			rx-fifo-depth = <0x40>;
+		};
diff --git a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt
index 7ff57a119f8..764c0c79b43 100644
--- a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt
+++ b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt
@@ -2,7 +2,9 @@ TI CPSW Phy mode Selection Device Tree Bindings
 -----------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,am3352-cpsw-phy-sel"
+- compatible		: Should be "ti,am3352-cpsw-phy-sel" for am335x platform and
+			  "ti,dra7xx-cpsw-phy-sel" for dra7xx platform
+			  "ti,am43xx-cpsw-phy-sel" for am43xx platform
 - reg			: physical base address and size of the cpsw
 			  registers map
 - reg-names		: names of the register map given in "reg" node
diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt
new file mode 100644
index 00000000000..82bf7e0f47b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fixed-link.txt
@@ -0,0 +1,42 @@
+Fixed link Device Tree binding
+------------------------------
+
+Some Ethernet MACs have a "fixed link", and are not connected to a
+normal MDIO-managed PHY device. For those situations, a Device Tree
+binding allows to describe a "fixed link".
+
+Such a fixed link situation is described by creating a 'fixed-link'
+sub-node of the Ethernet MAC device node, with the following
+properties:
+
+* 'speed' (integer, mandatory), to indicate the link speed. Accepted
+  values are 10, 100 and 1000
+* 'full-duplex' (boolean, optional), to indicate that full duplex is
+  used. When absent, half duplex is assumed.
+* 'pause' (boolean, optional), to indicate that pause should be
+  enabled.
+* 'asym-pause' (boolean, optional), to indicate that asym_pause should
+  be enabled.
+
+Old, deprecated 'fixed-link' binding:
+
+* A 'fixed-link' property in the Ethernet MAC node, with 5 cells, of the
+  form <a b c d e> with the following accepted values:
+  - a: emulated PHY ID, choose any but but unique to the all specified
+    fixed-links, from 0 to 31
+  - b: duplex configuration: 0 for half duplex, 1 for full duplex
+  - c: link speed in Mbits/sec, accepted values are: 10, 100 and 1000
+  - d: pause configuration: 0 for no pause, 1 for pause
+  - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for
+    asymmetric pause
+
+Example:
+
+ethernet@0 {
+	...
+	fixed-link {
+	      speed = <1000>;
+	      full-duplex;
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
index 737cdef4f90..be6ea8960f2 100644
--- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
+++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -42,10 +42,7 @@ Properties:
     interrupt.  For TSEC and eTSEC devices, the first interrupt is
     transmit, the second is receive, and the third is error.
   - phy-handle : See ethernet.txt file in the same directory.
-  - fixed-link : <a b c d e> where a is emulated phy id - choose any,
-    but unique to the all specified fixed-links, b is duplex - 0 half,
-    1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
-    pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
+  - fixed-link : See fixed-link.txt in the same directory.
   - phy-connection-type : See ethernet.txt file in the same directory.
     This property is only really needed if the connection is of type
     "rgmii-id", as all other connection types are detected by hardware.
diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt
new file mode 100644
index 00000000000..75d398bb1fb
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt
@@ -0,0 +1,36 @@
+Hisilicon hix5hd2 gmac controller
+
+Required properties:
+- compatible: should be "hisilicon,hix5hd2-gmac".
+- reg: specifies base physical address(s) and size of the device registers.
+  The first region is the MAC register base and size.
+  The second region is external interface control register.
+- interrupts: should contain the MAC interrupt.
+- #address-cells: must be <1>.
+- #size-cells: must be <0>.
+- phy-mode: see ethernet.txt [1].
+- phy-handle: see ethernet.txt [1].
+- mac-address: see ethernet.txt [1].
+- clocks: clock phandle and specifier pair.
+
+- PHY subnode: inherits from phy binding [2]
+
+[1] Documentation/devicetree/bindings/net/ethernet.txt
+[2] Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+	gmac0: ethernet@f9840000 {
+		compatible = "hisilicon,hix5hd2-gmac";
+		reg = <0xf9840000 0x1000>,<0xf984300c 0x4>;
+		interrupts = <0 71 4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy-mode = "mii";
+		phy-handle = <&phy2>;
+		mac-address = [00 00 00 00 00 00];
+		clocks = <&clock HIX5HD2_MAC0_CLK>;
+
+		phy2: ethernet-phy@2 {
+			reg = <2>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt
new file mode 100644
index 00000000000..d3bbdded4cb
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt
@@ -0,0 +1,23 @@
+* AT86RF230 IEEE 802.15.4 *
+
+Required properties:
+  - compatible:		should be "atmel,at86rf230", "atmel,at86rf231",
+			"atmel,at86rf233" or "atmel,at86rf212"
+  - spi-max-frequency:	maximal bus speed, should be set to 7500000 depends
+			sync or async operation mode
+  - reg:		the chipselect index
+  - interrupts:		the interrupt generated by the device
+
+Optional properties:
+  - reset-gpio:		GPIO spec for the rstn pin
+  - sleep-gpio:		GPIO spec for the slp_tr pin
+
+Example:
+
+	at86rf231@0 {
+		compatible = "atmel,at86rf231";
+		spi-max-frequency = <7500000>;
+		reg = <0>;
+		interrupts = <19 1>;
+		interrupt-parent = <&gpio3>;
+	};
diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt
index d54d0cc7948..bbdf9a7359a 100644
--- a/Documentation/devicetree/bindings/net/micrel-ks8851.txt
+++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt
@@ -1,9 +1,18 @@
-Micrel KS8851 Ethernet mac
+Micrel KS8851 Ethernet mac (MLL)
 
 Required properties:
-- compatible = "micrel,ks8851-ml" of parallel interface
+- compatible = "micrel,ks8851-mll" of parallel interface
 - reg : 2 physical address and size of registers for data and command
 - interrupts : interrupt connection
 
+Micrel KS8851 Ethernet mac (SPI)
+
+Required properties:
+- compatible = "micrel,ks8851" or the deprecated "ks8851"
+- reg : chip select number
+- interrupts : interrupt connection
+
 Optional properties:
-- vdd-supply:	supply for Ethernet mac
+- vdd-supply: analog 3.3V supply for Ethernet mac
+- vdd-io-supply: digital 1.8V IO supply for Ethernet mac
+- reset-gpios: reset_n input pin
diff --git a/Documentation/devicetree/bindings/net/micrel-ksz9021.txt b/Documentation/devicetree/bindings/net/micrel-ksz9021.txt
deleted file mode 100644
index 997a63f1aea..00000000000
--- a/Documentation/devicetree/bindings/net/micrel-ksz9021.txt
+++ /dev/null
@@ -1,49 +0,0 @@
-Micrel KSZ9021 Gigabit Ethernet PHY
-
-Some boards require special tuning values, particularly when it comes to
-clock delays.  You can specify clock delay values by adding
-micrel-specific properties to an Ethernet OF device node.
-
-All skew control options are specified in picoseconds.  The minimum
-value is 0, and the maximum value is 3000.
-
-Optional properties:
- - rxc-skew-ps : Skew control of RXC pad
- - rxdv-skew-ps : Skew control of RX CTL pad
- - txc-skew-ps : Skew control of TXC pad
- - txen-skew-ps : Skew control of TX_CTL pad
- - rxd0-skew-ps : Skew control of RX data 0 pad
- - rxd1-skew-ps : Skew control of RX data 1 pad
- - rxd2-skew-ps : Skew control of RX data 2 pad
- - rxd3-skew-ps : Skew control of RX data 3 pad
- - txd0-skew-ps : Skew control of TX data 0 pad
- - txd1-skew-ps : Skew control of TX data 1 pad
- - txd2-skew-ps : Skew control of TX data 2 pad
- - txd3-skew-ps : Skew control of TX data 3 pad
-
-Examples:
-
-	/* Attach to an Ethernet device with autodetected PHY */
-	&enet {
-		rxc-skew-ps = <3000>;
-		rxdv-skew-ps = <0>;
-		txc-skew-ps = <3000>;
-		txen-skew-ps = <0>;
-		status = "okay";
-	};
-
-	/* Attach to an explicitly-specified PHY */
-	mdio {
-		phy0: ethernet-phy@0 {
-			rxc-skew-ps = <3000>;
-			rxdv-skew-ps = <0>;
-			txc-skew-ps = <3000>;
-			txen-skew-ps = <0>;
-			reg = <0>;
-		};
-	};
-	ethernet@70000 {
-		status = "okay";
-		phy = <&phy0>;
-		phy-mode = "rgmii-id";
-	};
diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
new file mode 100644
index 00000000000..692076fda0e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
@@ -0,0 +1,83 @@
+Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY
+
+Some boards require special tuning values, particularly when it comes to
+clock delays. You can specify clock delay values by adding
+micrel-specific properties to an Ethernet OF device node.
+
+Note that these settings are applied after any phy-specific fixup from
+phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c),
+and therefore may overwrite them.
+
+KSZ9021:
+
+  All skew control options are specified in picoseconds. The minimum
+  value is 0, the maximum value is 3000, and it is incremented by 200ps
+  steps.
+
+  Optional properties:
+
+    - rxc-skew-ps : Skew control of RXC pad
+    - rxdv-skew-ps : Skew control of RX CTL pad
+    - txc-skew-ps : Skew control of TXC pad
+    - txen-skew-ps : Skew control of TX CTL pad
+    - rxd0-skew-ps : Skew control of RX data 0 pad
+    - rxd1-skew-ps : Skew control of RX data 1 pad
+    - rxd2-skew-ps : Skew control of RX data 2 pad
+    - rxd3-skew-ps : Skew control of RX data 3 pad
+    - txd0-skew-ps : Skew control of TX data 0 pad
+    - txd1-skew-ps : Skew control of TX data 1 pad
+    - txd2-skew-ps : Skew control of TX data 2 pad
+    - txd3-skew-ps : Skew control of TX data 3 pad
+
+KSZ9031:
+
+  All skew control options are specified in picoseconds. The minimum
+  value is 0, and the maximum is property-dependent. The increment
+  step is 60ps.
+
+  Optional properties:
+
+    Maximum value of 1860:
+
+      - rxc-skew-ps : Skew control of RX clock pad
+      - txc-skew-ps : Skew control of TX clock pad
+
+    Maximum value of 900:
+
+      - rxdv-skew-ps : Skew control of RX CTL pad
+      - txen-skew-ps : Skew control of TX CTL pad
+      - rxd0-skew-ps : Skew control of RX data 0 pad
+      - rxd1-skew-ps : Skew control of RX data 1 pad
+      - rxd2-skew-ps : Skew control of RX data 2 pad
+      - rxd3-skew-ps : Skew control of RX data 3 pad
+      - txd0-skew-ps : Skew control of TX data 0 pad
+      - txd1-skew-ps : Skew control of TX data 1 pad
+      - txd2-skew-ps : Skew control of TX data 2 pad
+      - txd3-skew-ps : Skew control of TX data 3 pad
+
+Examples:
+
+	/* Attach to an Ethernet device with autodetected PHY */
+	&enet {
+		rxc-skew-ps = <3000>;
+		rxdv-skew-ps = <0>;
+		txc-skew-ps = <3000>;
+		txen-skew-ps = <0>;
+		status = "okay";
+	};
+
+	/* Attach to an explicitly-specified PHY */
+	mdio {
+		phy0: ethernet-phy@0 {
+			rxc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			txen-skew-ps = <0>;
+			reg = <0>;
+		};
+	};
+	ethernet@70000 {
+		status = "okay";
+		phy = <&phy0>;
+		phy-mode = "rgmii-id";
+	};
diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt
new file mode 100644
index 00000000000..dab69f36167
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt
@@ -0,0 +1,35 @@
+* NXP Semiconductors PN544 NFC Controller
+
+Required properties:
+- compatible: Should be "nxp,pn544-i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- enable-gpios: Output GPIO pin used for enabling/disabling the PN544
+- firmware-gpios: Output GPIO pin used to enter firmware download mode
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBone with PN544 on I2C2):
+
+&i2c2 {
+
+	status = "okay";
+
+	pn544: pn544@28 {
+
+		compatible = "nxp,pn544-i2c";
+
+		reg = <0x28>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 GPIO_ACTIVE_HIGH>;
+
+		enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt
new file mode 100644
index 00000000000..e4faa2e8dfe
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt
@@ -0,0 +1,33 @@
+* STMicroelectronics SAS. ST21NFCA NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfca_i2c".
+- clock-frequency: I²C work frequency.
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2):
+
+&i2c2 {
+
+	status = "okay";
+
+	st21nfca: st21nfca@1 {
+
+		compatible = "st,st21nfca_i2c";
+
+		reg = <0x01>;
+		clock-frequency = <400000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+		enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index 8dd3ef7bc56..1e436133685 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -12,6 +12,7 @@ Required properties:
 Optional SoC Specific Properties:
 - pinctrl-names: Contains only one value - "default".
 - pintctrl-0: Specifies the pin control groups used for this controller.
+- autosuspend-delay: Specify autosuspend delay in milliseconds.
 
 Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 
@@ -29,6 +30,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 		ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>,
 				  <&gpio2 5 GPIO_ACTIVE_LOW>;
 		vin-supply = <&ldo3_reg>;
+		autosuspend-delay = <30000>;
 		status = "okay";
 	};
 };
diff --git a/Documentation/devicetree/bindings/net/via-rhine.txt b/Documentation/devicetree/bindings/net/via-rhine.txt
new file mode 100644
index 00000000000..334eca2bf93
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/via-rhine.txt
@@ -0,0 +1,17 @@
+* VIA Rhine 10/100 Network Controller
+
+Required properties:
+- compatible : Should be "via,vt8500-rhine" for integrated
+	Rhine controllers found in VIA VT8500, WonderMedia WM8950
+	and similar. These are listed as 1106:3106 rev. 0x84 on the
+	virtual PCI bus under vendor-provided kernels
+- reg : Address and length of the io space
+- interrupts : Should contain the controller interrupt line
+
+Examples:
+
+ethernet@d8004000 {
+	compatible = "via,vt8500-rhine";
+	reg = <0xd8004000 0x100>;
+	interrupts = <10>;
+};