Merge tag 'asoc-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v3.17

This is mostly driver fixes, the biggest one being the tlv320aic31xx
which is relatively large but simple and device specific.  There's a
small fix in the error handling in DPCM too which is relatively minor
error handling fix.

7 files changed, 24 insertions, 8 deletions

diff --git a/Documentation/devicetree/bindings/dma/rcar-audmapp.txt b/Documentation/devicetree/bindings/dma/rcar-audmapp.txt
index 9f1d750d76d..61bca509d7b 100644
--- a/Documentation/devicetree/bindings/dma/rcar-audmapp.txt
+++ b/Documentation/devicetree/bindings/dma/rcar-audmapp.txt
@@ -16,9 +16,9 @@ Example:
 * DMA client
 
 Required properties:
-- dmas:		a list of <[DMA multiplexer phandle] [SRS/DRS value]> pairs,
-		where SRS/DRS values are fixed handles, specified in the SoC
-		manual as the value that would be written into the PDMACHCR.
+- dmas:		a list of <[DMA multiplexer phandle] [SRS << 8 | DRS]> pairs.
+		where SRS/DRS are specified in the SoC manual.
+		It will be written into PDMACHCR as high 16-bit parts.
 - dma-names:	a list of DMA channel names, one per "dmas" entry
 
 Example:
diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt
index baef432e836..0ac23f2ed10 100644
--- a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt
+++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt
@@ -15,6 +15,17 @@ Optional properties for main touchpad device:
     keycode generated by each GPIO. Linux keycodes are defined in
     <dt-bindings/input/input.h>.
 
+- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages
+    on GPIO bit changes. An array of up to 8 entries can be provided
+    indicating the Linux keycode mapped to each bit of the status byte,
+    starting at the LSB. Linux keycodes are defined in
+    <dt-bindings/input/input.h>.
+
+    Note: the numbering of the GPIOs and the bit they start at varies between
+    maXTouch devices. You must either refer to the documentation, or
+    experiment to determine which bit corresponds to which input. Use
+    KEY_RESERVED for unused padding values.
+
 Example:
 
 	touch@4b {
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index 9b03c57563a..e45ac3f926b 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -39,6 +39,10 @@ Optional properties:
   further clocks may be specified in derived bindings.
 - clock-names: One name for each entry in the clocks property, the
   first one should be "stmmaceth".
+- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is
+  available this clock is used for programming the Timestamp Addend Register.
+  If not passed then the system clock will be used and this is fine on some
+  platforms.
 
 Examples:
 
diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt
index 340980239ea..ca69f5e3040 100644
--- a/Documentation/devicetree/bindings/regulator/tps65090.txt
+++ b/Documentation/devicetree/bindings/regulator/tps65090.txt
@@ -45,8 +45,8 @@ Example:
 		infet5-supply = <&some_reg>;
 		infet6-supply = <&some_reg>;
 		infet7-supply = <&some_reg>;
-		vsys_l1-supply = <&some_reg>;
-		vsys_l2-supply = <&some_reg>;
+		vsys-l1-supply = <&some_reg>;
+		vsys-l2-supply = <&some_reg>;
 
 		regulators {
 			dcdc1 {
diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
index 6c55fcfe5e1..9b82c20b306 100644
--- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
+++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
@@ -31,7 +31,7 @@ i2s@ff890000 {
 	#address-cells = <1>;
 	#size-cells = <0>;
 	dmas = <&pdma1 0>, <&pdma1 1>;
-	dma-names = "rx", "tx";
+	dma-names = "tx", "rx";
 	clock-names = "i2s_hclk", "i2s_clk";
 	clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
 };
diff --git a/Documentation/devicetree/bindings/usb/mxs-phy.txt b/Documentation/devicetree/bindings/usb/mxs-phy.txt
index cef181a9d8b..96681c93b86 100644
--- a/Documentation/devicetree/bindings/usb/mxs-phy.txt
+++ b/Documentation/devicetree/bindings/usb/mxs-phy.txt
@@ -5,6 +5,7 @@ Required properties:
 	* "fsl,imx23-usbphy" for imx23 and imx28
 	* "fsl,imx6q-usbphy" for imx6dq and imx6dl
 	* "fsl,imx6sl-usbphy" for imx6sl
+	* "fsl,imx6sx-usbphy" for imx6sx
   "fsl,imx23-usbphy" is still a fallback for other strings
 - reg: Should contain registers location and length
 - interrupts: Should contain phy interrupt
diff --git a/Documentation/devicetree/bindings/video/analog-tv-connector.txt b/Documentation/devicetree/bindings/video/analog-tv-connector.txt
index 0218fcdc129..0c0970c210a 100644
--- a/Documentation/devicetree/bindings/video/analog-tv-connector.txt
+++ b/Documentation/devicetree/bindings/video/analog-tv-connector.txt
@@ -2,7 +2,7 @@ Analog TV Connector
 ===================
 
 Required properties:
-- compatible: "composite-connector" or "svideo-connector"
+- compatible: "composite-video-connector" or "svideo-connector"
 
 Optional properties:
 - label: a symbolic name for the connector
@@ -14,7 +14,7 @@ Example
 -------
 
 tv: connector {
-	compatible = "composite-connector";
+	compatible = "composite-video-connector";
 	label = "tv";
 
 	port {