Merge tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "Here is a batch of GPIO changes for v3.11.  I have agreed with Grant
  to take care of the pull requests for this development cycle.

  No special things are happening in the GPIO tree this time (nice with
  some calm) and I have been extra careful to do regression builds and
  it's well boiled in -next.

  GPIO changes for the v3.11 development cycle:
   - Incremental development for the Langwell (Atom SoC), Xilinx, ICH
     and RCAR drivers.
   - Cleanups from Jingoo Han, Axel Lin, Wei Jongjun, Wolfram Sang,
     Tushar Behera, Sachin Kamat and Yijing Wang"

* tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (35 commits)
  Gpio/trivial: replace numeric with standard PM state macros
  gpiolib: remove warnning of allocations with IRQs disabled
  gpio: grgpio: Staticize local symbols
  gpio-langwell: remove Withney point support
  gpio: ich: add GPO_BLINK support
  gpio-sta2x11: Convert to use devm_ioremap_resource
  gpio_msm: Convert to use devm_ioremap_resource
  gpio-rcar: Use OUTDT when reading GPIOs configured as output
  gpio-sta2x11: Fix potential NULL pointer dereference
  gpio/omap: omap_gpio_init_context stub must be inline
  gpio: msm-v1: Remove errant __devinit to fix compile
  gpio: devres: make comments proper
  GPIO: xilinx: Enable driver for Xilinx zynq
  DT: Add documentation for gpio-xilinx
  GPIO: xilinx: Use BIT macro
  GPIO: xilinx: Use __raw_readl/__raw_writel IO functions
  GPIO: xilinx: Add support for dual channel
  GPIO: xilinx: Simplify driver probe function
  gpio: sx150x: convert to use devm_* functions
  MAINTAINERS: add linux-gpio mailing list
  ...

1 files changed, 48 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
new file mode 100644
index 00000000000..63bf4becd5f
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
@@ -0,0 +1,48 @@
+Xilinx plb/axi GPIO controller
+
+Dual channel GPIO controller with configurable number of pins
+(from 1 to 32 per channel). Every pin can be configured as
+input/output/tristate. Both channels share the same global IRQ but
+local interrupts can be enabled on channel basis.
+
+Required properties:
+- compatible : Should be "xlnx,xps-gpio-1.00.a"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+- gpio-controller : Marks the device node as a GPIO controller.
+
+Optional properties:
+- interrupts : Interrupt mapping for GPIO IRQ.
+- interrupt-parent : Phandle for the interrupt controller that
+  services interrupts for this device.
+- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input
+- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1
+- xlnx,gpio-width : gpio width
+- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode
+- xlnx,is-dual : if 1, controller also uses the second channel
+- xlnx,all-inputs-2 : as above but for the second channel
+- xlnx,dout-default-2 : as above but the second channel
+- xlnx,gpio2-width : as above but for the second channel
+- xlnx,tri-default-2 : as above but for the second channel
+
+
+Example:
+gpio: gpio@40000000 {
+	#gpio-cells = <2>;
+	compatible = "xlnx,xps-gpio-1.00.a";
+	gpio-controller ;
+	interrupt-parent = <&microblaze_0_intc>;
+	interrupts = < 6 2 >;
+	reg = < 0x40000000 0x10000 >;
+	xlnx,all-inputs = <0x0>;
+	xlnx,all-inputs-2 = <0x0>;
+	xlnx,dout-default = <0x0>;
+	xlnx,dout-default-2 = <0x0>;
+	xlnx,gpio-width = <0x2>;
+	xlnx,gpio2-width = <0x2>;
+	xlnx,interrupt-present = <0x1>;
+	xlnx,is-dual = <0x1>;
+	xlnx,tri-default = <0xffffffff>;
+	xlnx,tri-default-2 = <0xffffffff>;
+} ;