Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc driver specific changes from Olof Johansson:
 - A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer

Fix up conflicts as per Olof.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: bus: omap_l3: use resources instead of hardcoded irqs
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  drivers: bus: Move the OMAP interconnect driver to drivers/bus/
  i2c: tegra: dynamically control fast clk
  i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
  ARM: tegra: clock: remove unused clock entry for i2c
  ARM: tegra: clock: add connection name in i2c clock entry
  i2c: tegra: pass proper name for getting clock
  ARM: tegra: clock: add i2c fast clock entry in clock table
  ARM: EXYNOS: Adds G-Scaler device from Device Tree
  ARM: EXYNOS: Add clock support for G-Scaler
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  ...

3 files changed, 236 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
new file mode 100644
index 00000000000..d2fe064a828
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
@@ -0,0 +1,10 @@
+* OMAP OCP2SCP - ocp interface to scp interface
+
+properties:
+- compatible : Should be "ti,omap-ocp2scp"
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ranges : the child address space are mapped 1:1 onto the parent address space
+- ti,hwmods : must be "ocp2scp_usb_phy"
+
+Sub-nodes:
+All the devices connected to ocp2scp are described using sub-node to ocp2scp
diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt
new file mode 100644
index 00000000000..0604d42f38d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt
@@ -0,0 +1,30 @@
+* Samsung Exynos5 G-Scaler device
+
+G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs.
+
+Required properties:
+- compatible: should be "samsung,exynos5-gsc"
+- reg: should contain G-Scaler physical address location and length.
+- interrupts: should contain G-Scaler interrupt number
+
+Example:
+
+gsc_0:  gsc@0x13e00000 {
+	compatible = "samsung,exynos5-gsc";
+	reg = <0x13e00000 0x1000>;
+	interrupts = <0 85 0>;
+};
+
+Aliases:
+Each G-Scaler node should have a numbered alias in the aliases node,
+in the form of gscN, N = 0...3. G-Scaler driver uses these aliases
+to retrieve the device IDs using "of_alias_get_id()" call.
+
+Example:
+
+aliases {
+	gsc0 =&gsc_0;
+	gsc1 =&gsc_1;
+	gsc2 =&gsc_2;
+	gsc3 =&gsc_3;
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
new file mode 100644
index 00000000000..03dee50532f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -0,0 +1,196 @@
+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+- interrupts: interrupt specifier for the controller. The format and value of
+  the interrupt specifier depends on the interrupt parent for the controller.
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be atleast one
+  child node and there is no limit on the count of these child nodes.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be atleast one pin specfied for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include atleast a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+- interrupt-controller: identifies the controller node as interrupt-parent.
+- #interrupt-cells: the value of this property should be 2.
+  - First Cell: represents the external gpio interrupt number local to the
+    external gpio interrupt space of the controller.
+  - Second Cell: flags to identify the type of the interrupt
+    - 1 = rising edge triggered
+    - 2 = falling edge triggered
+    - 3 = rising and falling edge triggered
+    - 4 = high level triggered
+    - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node. This child node should include
+   the following properties.
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 SoC.
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Example 1: A pin-controller node with pin groups.
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+	uart@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+		pinctrl-names = "default", "flow-control;
+		pinctrl-0 = <&uart0_data>;
+		pinctrl-1 = <&uart0_data &uart0_fctl>;
+	};
+
+Example 4: Set up the default pin state for uart controller.
+
+	static int s3c24xx_serial_probe(struct platform_device *pdev) {
+		struct pinctrl *pinctrl;
+		...
+		...
+		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	}