Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB patches from Greg Kroah-Hartman:
 "Here's the big USB merge for 3.9-rc1

  Nothing major, lots of gadget fixes, and of course, xhci stuff.

  All of this has been in linux-next for a while, with the exception of
  the last 3 patches, which were reverts of patches in the tree that
  caused problems, they went in yesterday."

* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (190 commits)
  Revert "USB: EHCI: make ehci-vt8500 a separate driver"
  Revert "USB: EHCI: make ehci-orion a separate driver"
  Revert "USB: update host controller Kconfig entries"
  USB: update host controller Kconfig entries
  USB: EHCI: make ehci-orion a separate driver
  USB: EHCI: make ehci-vt8500 a separate driver
  USB: usb-storage: unusual_devs update for Super TOP SATA bridge
  USB: ehci-omap: Fix autoloading of module
  USB: ehci-omap: Don't free gpios that we didn't request
  USB: option: add Huawei "ACM" devices using protocol = vendor
  USB: serial: fix null-pointer dereferences on disconnect
  USB: option: add Yota / Megafon M100-1 4g modem
  drivers/usb: add missing GENERIC_HARDIRQS dependencies
  USB: storage: properly handle the endian issues of idProduct
  testusb: remove all mentions of 'usbfs'
  usb: gadget: imx_udc: make it depend on BROKEN
  usb: omap_control_usb: fix compile warning
  ARM: OMAP: USB: Add phy binding information
  ARM: OMAP2: MUSB: Specify omap4 has mailbox
  ARM: OMAP: devices: create device for usb part of control module
  ...

5 files changed, 160 insertions, 6 deletions

diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
new file mode 100644
index 00000000000..7a95c651ceb
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -0,0 +1,22 @@
+synopsys DWC3 CORE
+
+DWC3- USB3 CONTROLLER
+
+Required properties:
+ - compatible: must be "synopsys,dwc3"
+ - reg : Address and length of the register set for the device
+ - interrupts: Interrupts used by the dwc3 controller.
+ - usb-phy : array of phandle for the PHY device
+
+Optional properties:
+ - tx-fifo-resize: determines if the FIFO *has* to be reallocated.
+
+This is usually a subnode to DWC3 glue to which it is connected.
+
+dwc3@4a030000 {
+	compatible = "synopsys,dwc3";
+	reg = <0x4a030000 0xcfff>;
+	interrupts = <0 92 4>
+	usb-phy = <&usb2_phy>, <&usb3,phy>;
+	tx-fifo-resize;
+};
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 29a043ecda5..1ef0ce71f8f 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -1,8 +1,11 @@
-OMAP GLUE
+OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
 
 OMAP MUSB GLUE
  - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
  - ti,hwmods : must be "usb_otg_hs"
+ - ti,has-mailbox : to specify that omap uses an external mailbox
+   (in control module) to communicate with the musb core during device connect
+   and disconnect.
  - multipoint : Should be "1" indicating the musb controller supports
    multipoint. This is a MUSB configuration-specific setting.
  - num_eps : Specifies the number of endpoints. This is also a
@@ -16,13 +19,19 @@ OMAP MUSB GLUE
  - power : Should be "50". This signifies the controller can supply upto
    100mA when operating in host mode.
 
+Optional properties:
+ - ctrl-module : phandle of the control module this glue uses to write to
+   mailbox
+
 SOC specific device node entry
 usb_otg_hs: usb_otg_hs@4a0ab000 {
 	compatible = "ti,omap4-musb";
 	ti,hwmods = "usb_otg_hs";
+	ti,has-mailbox;
 	multipoint = <1>;
 	num_eps = <16>;
 	ram_bits = <12>;
+	ctrl-module = <&omap_control_usb>;
 };
 
 Board specific device node entry
@@ -31,3 +40,26 @@ Board specific device node entry
 	mode = <3>;
 	power = <50>;
 };
+
+OMAP CONTROL USB
+
+Required properties:
+ - compatible: Should be "ti,omap-control-usb"
+ - reg : Address and length of the register set for the device. It contains
+   the address of "control_dev_conf" and "otghs_control" or "phy_power_usb"
+   depending upon omap4 or omap5.
+ - reg-names: The names of the register addresses corresponding to the registers
+   filled in "reg".
+ - ti,type: This is used to differentiate whether the control module has
+   usb mailbox or usb3 phy power. omap4 has usb mailbox in control module to
+   notify events to the musb core and omap5 has usb3 phy power register to
+   power on usb3 phy. Should be "1" if it has mailbox and "2" if it has usb3
+   phy power.
+
+omap_control_usb: omap-control-usb@4a002300 {
+	compatible = "ti,omap-control-usb";
+	reg = <0x4a002300 0x4>,
+	      <0x4a00233c 0x4>;
+	reg-names = "control_dev_conf", "otghs_control";
+	ti,type = <1>;
+};
diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt
new file mode 100644
index 00000000000..033194934f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt
@@ -0,0 +1,55 @@
+* Samsung's usb phy transceiver
+
+The Samsung's phy transceiver is used for controlling usb phy for
+s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers
+across Samsung SOCs.
+TODO: Adding the PHY binding with controller(s) according to the under
+developement generic PHY driver.
+
+Required properties:
+
+Exynos4210:
+- compatible : should be "samsung,exynos4210-usbphy"
+- reg : base physical address of the phy registers and length of memory mapped
+	region.
+
+Exynos5250:
+- compatible : should be "samsung,exynos5250-usbphy"
+- reg : base physical address of the phy registers and length of memory mapped
+	region.
+
+Optional properties:
+- #address-cells: should be '1' when usbphy node has a child node with 'reg'
+		  property.
+- #size-cells: should be '1' when usbphy node has a child node with 'reg'
+	       property.
+- ranges: allows valid translation between child's address space and parent's
+	  address space.
+
+- The child node 'usbphy-sys' to the node 'usbphy' is for the system controller
+  interface for usb-phy. It should provide the following information required by
+  usb-phy controller to control phy.
+  - reg : base physical address of PHY_CONTROL registers.
+	  The size of this register is the total sum of size of all PHY_CONTROL
+	  registers that the SoC has. For example, the size will be
+	  '0x4' in case we have only one PHY_CONTROL register (e.g.
+	  OTHERS register in S3C64XX or USB_PHY_CONTROL register in S5PV210)
+	  and, '0x8' in case we have two PHY_CONTROL registers (e.g.
+	  USBDEVICE_PHY_CONTROL and USBHOST_PHY_CONTROL registers in exynos4x).
+	  and so on.
+
+Example:
+ - Exynos4210
+
+	usbphy@125B0000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "samsung,exynos4210-usbphy";
+		reg = <0x125B0000 0x100>;
+		ranges;
+
+		usbphy-sys {
+			/* USB device and host PHY_CONTROL registers */
+			reg = <0x10020704 0x8>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
index 80d4148cb66..61496f5cb09 100644
--- a/Documentation/devicetree/bindings/usb/usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -4,14 +4,39 @@ OMAP USB2 PHY
 
 Required properties:
  - compatible: Should be "ti,omap-usb2"
- - reg : Address and length of the register set for the device. Also
-add the address of control module dev conf register until a driver for
-control module is added
+ - reg : Address and length of the register set for the device.
+
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+   the PHY.
 
 This is usually a subnode of ocp2scp to which it is connected.
 
 usb2phy@4a0ad080 {
 	compatible = "ti,omap-usb2";
-	reg = <0x4a0ad080 0x58>,
-	      <0x4a002300 0x4>;
+	reg = <0x4a0ad080 0x58>;
+	ctrl-module = <&omap_control_usb>;
+};
+
+OMAP USB3 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb3"
+ - reg : Address and length of the register set for the device.
+ - reg-names: The names of the register addresses corresponding to the registers
+   filled in "reg".
+
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+   the PHY.
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb3phy@4a084400 {
+	compatible = "ti,omap-usb3";
+	reg = <0x4a084400 0x80>,
+	      <0x4a084800 0x64>,
+	      <0x4a084c00 0x40>;
+	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
+	ctrl-module = <&omap_control_usb>;
 };
diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt
new file mode 100644
index 00000000000..6813a715fc7
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/usb3503.txt
@@ -0,0 +1,20 @@
+SMSC USB3503 High-Speed Hub Controller
+
+Required properties:
+- compatible: Should be "smsc,usb3503".
+- reg: Specifies the i2c slave address, it should be 0x08.
+- connect-gpios: Should specify GPIO for connect.
+- intn-gpios: Should specify GPIO for interrupt.
+- reset-gpios: Should specify GPIO for reset.
+- initial-mode: Should specify initial mode.
+                (1 for HUB mode, 2 for STANDBY mode)
+
+Examples:
+	usb3503@08 {
+		compatible = "smsc,usb3503";
+		reg = <0x08>;
+		connect-gpios = <&gpx3 0 1>;
+		intn-gpios = <&gpx3 4 1>;
+		reset-gpios = <&gpx3 5 1>;
+		initial-mode = <1>;
+	};