Merge tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 - A few SPI NOR ID definitions
 - Kill the NAND "max pagesize" restriction
 - Fix some x16 bus-width NAND support
 - Add NAND JEDEC parameter page support
 - DT bindings for NAND ECC
 - GPMI NAND updates (subpage reads)
 - More OMAP NAND refactoring
 - New STMicro SPI NOR driver (now in 40 patches!)
 - A few other random bugfixes

* tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd: (120 commits)
  Fix index regression in nand_read_subpage
  mtd: diskonchip: mem resource name is not optional
  mtd: nand: fix mention to CONFIG_MTD_NAND_ECC_BCH
  mtd: nand: fix GET/SET_FEATURES address on 16-bit devices
  mtd: omap2: Use devm_ioremap_resource()
  mtd: denali_dt: Use devm_ioremap_resource()
  mtd: devices: elm: update DRIVER_NAME as "omap-elm"
  mtd: devices: elm: configure parallel channels based on ecc_steps
  mtd: devices: elm: clean elm_load_syndrome
  mtd: devices: elm: check for hardware engine's design constraints
  mtd: st_spi_fsm: Succinctly reorganise .remove()
  mtd: st_spi_fsm: Allow loop to run at least once before giving up CPU
  mtd: st_spi_fsm: Correct vendor name spelling issue - missing "M"
  mtd: st_spi_fsm: Avoid duplicating MTD core code
  mtd: st_spi_fsm: Remove useless consts from function arguments
  mtd: st_spi_fsm: Convert ST SPI FSM (NOR) Flash driver to new DT partitions
  mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct
  mtd: st_spi_fsm: Supply the W25Qxxx chip specific configuration call-back
  mtd: st_spi_fsm: Supply the S25FLxxx chip specific configuration call-back
  mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back
  ...

2 files changed, 40 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
index 03855c8c492..b53f92e252d 100644
--- a/Documentation/devicetree/bindings/mtd/nand.txt
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -5,3 +5,17 @@
   "soft_bch".
 - nand-bus-width : 8 or 16 bus width if not present 8
 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+
+- nand-ecc-strength: integer representing the number of bits to correct
+		     per ECC step.
+
+- nand-ecc-step-size: integer representing the number of data bytes
+		      that are covered by a single ECC step.
+
+The ECC strength and ECC step size properties define the correction capability
+of a controller. Together, they say a controller can correct "{strength} bit
+errors per {size} bytes".
+
+The interpretation of these parameters is implementation-defined, so not all
+implementations must support all possible combinations. However, implementations
+are encouraged to further specify the value(s) they support.
diff --git a/Documentation/devicetree/bindings/mtd/st-fsm.txt b/Documentation/devicetree/bindings/mtd/st-fsm.txt
new file mode 100644
index 00000000000..c2489391c43
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/st-fsm.txt
@@ -0,0 +1,26 @@
+* ST-Microelectronics SPI FSM Serial (NOR) Flash Controller
+
+Required properties:
+  - compatible : Should be "st,spi-fsm"
+  - reg        : Contains register's location and length.
+  - reg-names  : Should contain the reg names "spi-fsm"
+  - interrupts : The interrupt number
+  - pinctrl-0  : Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt)
+
+Optional properties:
+  - st,syscfg          : Phandle to boot-device system configuration registers
+  - st,boot-device-reg : Address of the aforementioned boot-device register(s)
+  - st,boot-device-spi : Expected boot-device value if booted via this device
+
+Example:
+	spifsm: spifsm@fe902000{
+	        compatible         = "st,spi-fsm";
+	        reg                =  <0xfe902000 0x1000>;
+	        reg-names          = "spi-fsm";
+	        pinctrl-0          = <&pinctrl_fsm>;
+		st,syscfg	   = <&syscfg_rear>;
+	        st,boot-device-reg = <0x958>;
+	        st,boot-device-spi = <0x1a>;
+		status = "okay";
+	};
+