Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
  rtc: max8925: Add function to work as wakeup source
  mfd: Add pm ops to max8925
  mfd: Convert aat2870 to dev_pm_ops
  mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
  mfd: Introduce missing kfree in 88pm860x probe routine
  mfd: Add S5M series configuration
  mfd: Add s5m series irq driver
  mfd: Add S5M core driver
  mfd: Improve mc13xxx dt binding document
  mfd: Fix stmpe section mismatch
  mfd: Fix stmpe build warning
  mfd: Fix STMPE I2c build failure
  mfd: Constify aat2870-core i2c_device_id table
  gpio: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 610
  mfd: Add support for STMPE SPI interface
  mfd: Separate out STMPE controller and interface specific code
  misc: Remove max8997-muic sysfs attributes
  mfd: Remove unused wm831x_irq_data_to_mask_reg()
  ...

Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.

2 files changed, 125 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt
new file mode 100644
index 00000000000..19f6af47a79
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt
@@ -0,0 +1,78 @@
+* Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC)
+
+Required properties:
+- compatible : Should be "fsl,mc13783" or "fsl,mc13892"
+
+Optional properties:
+- fsl,mc13xxx-uses-adc : Indicate the ADC is being used
+- fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used
+- fsl,mc13xxx-uses-rtc : Indicate the RTC is being used
+- fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used
+
+Sub-nodes:
+- regulators : Contain the regulator nodes.  The MC13892 regulators are
+  bound using their names as listed below with their registers and bits
+  for enabling.
+
+    vcoincell : regulator VCOINCELL (register 13, bit 23)
+    sw1       : regulator SW1	    (register 24, bit 0)
+    sw2       : regulator SW2	    (register 25, bit 0)
+    sw3       : regulator SW3	    (register 26, bit 0)
+    sw4       : regulator SW4	    (register 27, bit 0)
+    swbst     : regulator SWBST	    (register 29, bit 20)
+    vgen1     : regulator VGEN1	    (register 32, bit 0)
+    viohi     : regulator VIOHI	    (register 32, bit 3)
+    vdig      : regulator VDIG	    (register 32, bit 9)
+    vgen2     : regulator VGEN2	    (register 32, bit 12)
+    vpll      : regulator VPLL	    (register 32, bit 15)
+    vusb2     : regulator VUSB2	    (register 32, bit 18)
+    vgen3     : regulator VGEN3	    (register 33, bit 0)
+    vcam      : regulator VCAM	    (register 33, bit 6)
+    vvideo    : regulator VVIDEO    (register 33, bit 12)
+    vaudio    : regulator VAUDIO    (register 33, bit 15)
+    vsd       : regulator VSD	    (register 33, bit 18)
+    gpo1      : regulator GPO1	    (register 34, bit 6)
+    gpo2      : regulator GPO2	    (register 34, bit 8)
+    gpo3      : regulator GPO3	    (register 34, bit 10)
+    gpo4      : regulator GPO4	    (register 34, bit 12)
+    pwgt1spi  : regulator PWGT1SPI  (register 34, bit 15)
+    pwgt2spi  : regulator PWGT2SPI  (register 34, bit 16)
+    vusb      : regulator VUSB	    (register 50, bit 3)
+
+  The bindings details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+Examples:
+
+ecspi@70010000 { /* ECSPI1 */
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
+		   <&gpio3 25 0>; /* GPIO4_25 */
+	status = "okay";
+
+	pmic: mc13892@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mc13892";
+		spi-max-frequency = <6000000>;
+		reg = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8>;
+
+		regulators {
+			sw1_reg: mc13892__sw1 {
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1375000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: mc13892__sw2 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/twl-familly.txt b/Documentation/devicetree/bindings/mfd/twl-familly.txt
new file mode 100644
index 00000000000..a66fcf94675
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/twl-familly.txt
@@ -0,0 +1,47 @@
+Texas Instruments TWL family
+
+The TWLs are Integrated Power Management Chips.
+Some version might contain much more analog function like
+USB transceiver or Audio amplifier.
+These chips are connected to an i2c bus.
+
+
+Required properties:
+- compatible : Must be "ti,twl4030";
+  For Integrated power-management/audio CODEC device used in OMAP3
+  based boards
+- compatible : Must be "ti,twl6030";
+  For Integrated power-management used in OMAP4 based boards
+- interrupts : This i2c device has an IRQ line connected to the main SoC
+- interrupt-controller : Since the twl support several interrupts internally,
+  it is considered as an interrupt controller cascaded to the SoC one.
+- #interrupt-cells = <1>;
+- interrupt-parent : The parent interrupt controller.
+
+Optional node:
+- Child nodes contain in the twl. The twl family is made of several variants
+  that support a different number of features.
+  The children nodes will thus depend of the capability of the variant.
+
+
+Example:
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/twl6030.pdf
+ */
+twl@48 {
+    compatible = "ti,twl6030";
+    reg = <0x48>;
+    interrupts = <39>; /* IRQ_SYS_1N cascaded to gic */
+    interrupt-controller;
+    #interrupt-cells = <1>;
+    interrupt-parent = <&gic>;
+    #address-cells = <1>;
+    #size-cells = <0>;
+
+    twl_rtc {
+        compatible = "ti,twl_rtc";
+        interrupts = <11>;
+        reg = <0>;
+    };
+};