ARM: 8169/1: l2c: parse cache properties from ePAPR definitions

When both 'cache-size' and 'cache-sets' are specified for a L2 cache
controller node, parse those properties and set up the
set size based on which type of L2 cache controller we are using.

Update the L2 cache controller Device Tree binding with the optional
'cache-size', 'cache-sets', 'cache-block-size' and 'cache-line-size'
properties. These come from the ePAPR specification.

Using the cache size, number of sets and cache line size we can
calculate desired associativity of the L2 cache. This is done
by the calculation:

    set size = cache size / sets
    ways = set size / line size
    way size = cache size / ways = sets * line size
    associativity = cache size / way size

Example output from the PB1176 DT that look like this:

L2: l2-cache {
    compatible = "arm,l220-cache";
    (...)
    arm,override-auxreg;
    cache-size = <131072>; // 128kB
    cache-sets = <512>;
    cache-line-size = <32>;
};

Ends up like this:

L2C OF: override cache size: 131072 bytes (128KB)
L2C OF: override line size: 32 bytes
L2C OF: override way size: 16384 bytes (16KB)
L2C OF: override associativity: 8
L2C: DT/platform modifies aux control register: 0x02020fff -> 0x02030fff
L2C-220 cache controller enabled, 8 ways, 128 kB
L2C-220: CACHE_ID 0x41000486, AUX_CTRL 0x06030fff

Which is consistent with the value earlier hardcoded for the
PB1176 platform.

This patch is an extended version based on the initial patch
by Florian Fainelli.

Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 10 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
index af527ee111c..292ef7ca305 100644
--- a/Documentation/devicetree/bindings/arm/l2cc.txt
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -2,6 +2,10 @@
 
 ARM cores often have a separate level 2 cache controller. There are various
 implementations of the L2 cache controller with compatible programming models.
+Some of the properties that are just prefixed "cache-*" are taken from section
+3.7.3 of the ePAPR v1.1 specification which can be found at:
+https://www.power.org/wp-content/uploads/2012/06/Power_ePAPR_APPROVED_v1.1.pdf
+
 The ARM L2 cache representation in the device tree should be done as follows:
 
 Required properties:
@@ -44,6 +48,12 @@ Optional properties:
   I/O coherent mode. Valid only when the arm,pl310-cache compatible
   string is used.
 - interrupts : 1 combined interrupt.
+- cache-size : specifies the size in bytes of the cache
+- cache-sets : specifies the number of associativity sets of the cache
+- cache-block-size : specifies the size in bytes of a cache block
+- cache-line-size : specifies the size in bytes of a line in the cache,
+  if this is not specified, the line size is assumed to be equal to the
+  cache block size
 - cache-id-part: cache id part number to be used if it is not present
   on hardware
 - wt-override: If present then L2 is forced to Write through mode