Merge branch 'sh/dmaengine' into sh-latest

39 files changed, 1094 insertions, 47 deletions

diff --git a/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt b/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt
new file mode 100644
index 00000000000..94e642a33db
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt
@@ -0,0 +1,15 @@
+Calxeda Highbank L2 cache ECC
+
+Properties:
+- compatible : Should be "calxeda,hb-sregs-l2-ecc"
+- reg : Address and size for ECC error interrupt clear registers.
+- interrupts : Should be single bit error interrupt, then double bit error
+	interrupt.
+
+Example:
+
+	sregs@fff3c200 {
+		compatible = "calxeda,hb-sregs-l2-ecc";
+		reg = <0xfff3c200 0x100>;
+		interrupts = <0 71 4  0 72 4>;
+	};
diff --git a/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt
new file mode 100644
index 00000000000..f770ac0893d
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt
@@ -0,0 +1,14 @@
+Calxeda DDR memory controller
+
+Properties:
+- compatible : Should be "calxeda,hb-ddr-ctrl"
+- reg : Address and size for DDR controller registers.
+- interrupts : Interrupt for DDR controller.
+
+Example:
+
+	memory-controller@fff00000 {
+		compatible = "calxeda,hb-ddr-ctrl";
+		reg = <0xfff00000 0x1000>;
+		interrupts = <0 91 4>;
+	};
diff --git a/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt
new file mode 100644
index 00000000000..93986a5a801
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt
@@ -0,0 +1,30 @@
+* Compact Flash
+
+The Cavium Compact Flash device is connected to the Octeon Boot Bus,
+and is thus a child of the Boot Bus device.  It can read and write
+industry standard compact flash devices.
+
+Properties:
+- compatible: "cavium,ebt3000-compact-flash";
+
+  Compatibility with many Cavium evaluation boards.
+
+- reg: The base address of the the CF chip select banks.  Depending on
+  the device configuration, there may be one or two banks.
+
+- cavium,bus-width: The width of the connection to the CF devices.  Valid
+  values are 8 and 16.
+
+- cavium,true-ide: Optional, if present the CF connection is in True IDE mode.
+
+- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected
+  to this device.
+
+Example:
+	compact-flash@5,0 {
+		compatible = "cavium,ebt3000-compact-flash";
+		reg = <5 0 0x10000>, <6 0 0x10000>;
+		cavium,bus-width = <16>;
+		cavium,true-ide;
+		cavium,dma-engine-handle = <&dma0>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
new file mode 100644
index 00000000000..9d6dcd3fe7f
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
@@ -0,0 +1,49 @@
+* General Purpose Input Output (GPIO) bus.
+
+Properties:
+- compatible: "cavium,octeon-3860-gpio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the GPIO unit's register bank.
+
+- gpio-controller: This is a GPIO controller.
+
+- #gpio-cells: Must be <2>.  The first cell is the GPIO pin.
+
+- interrupt-controller: The GPIO controller is also an interrupt
+  controller, many of its pins may be configured as an interrupt
+  source.
+
+- #interrupt-cells: Must be <2>.  The first cell is the GPIO pin
+   connected to the interrupt source.  The second cell is the interrupt
+   triggering protocol and may have one of four values:
+   1 - edge triggered on the rising edge.
+   2 - edge triggered on the falling edge
+   4 - level triggered active high.
+   8 - level triggered active low.
+
+- interrupts: Interrupt routing for each pin.
+
+Example:
+
+	gpio-controller@1070000000800 {
+		#gpio-cells = <2>;
+		compatible = "cavium,octeon-3860-gpio";
+		reg = <0x10700 0x00000800 0x0 0x100>;
+		gpio-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) GPIO pin number (0..15)
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		/* The GPIO pin connect to 16 consecutive CUI bits */
+		interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+			     <0 20>, <0 21>, <0 22>, <0 23>,
+			     <0 24>, <0 25>, <0 26>, <0 27>,
+			     <0 28>, <0 29>, <0 30>, <0 31>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
index 4f3929713ae..dbd22e0df21 100644
--- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
@@ -22,7 +22,7 @@ Required properties:
 Example:
 
 gpio0: gpio@73f84000 {
-	compatible = "fsl,imx51-gpio", "fsl,imx31-gpio";
+	compatible = "fsl,imx51-gpio", "fsl,imx35-gpio";
 	reg = <0x73f84000 0x4000>;
 	interrupts = <50 51>;
 	gpio-controller;
diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
index 8f50fe5e6c4..5375625e8cd 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
@@ -11,14 +11,15 @@ Required properties:
      <[phandle of the gpio controller node]
       [pin number within the gpio controller]
       [mux function]
-      [pull up/down]
+      [flags and pull up/down]
       [drive strength]>
 
   Values for gpio specifier:
   - Pin number: is a value between 0 to 7.
-  - Pull Up/Down: 0 - Pull Up/Down Disabled.
-                  1 - Pull Down Enabled.
-                  3 - Pull Up Enabled.
+  - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled.
+                            1 - Pull Down Enabled.
+                            3 - Pull Up Enabled.
+          Bit 16 (0x00010000) - Input is active low.
   - Drive Strength: 0 - 1x,
                     1 - 3x,
                     2 - 2x,
diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt
new file mode 100644
index 00000000000..dced82ebe31
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt
@@ -0,0 +1,34 @@
+* Two Wire Serial Interface (TWSI) / I2C
+
+- compatible: "cavium,octeon-3860-twsi"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the TWSI/I2C bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  I2C addresses have no size component.
+
+- interrupts: A single interrupt specifier.
+
+- clock-frequency: The I2C bus clock rate in Hz.
+
+Example:
+	twsi0: i2c@1180000001000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "cavium,octeon-3860-twsi";
+		reg = <0x11800 0x00001000 0x0 0x200>;
+		interrupts = <0 45>;
+		clock-frequency = <100000>;
+
+		rtc@68 {
+			compatible = "dallas,ds1337";
+			reg = <0x68>;
+		};
+		tmp@4c {
+			compatible = "ti,tmp421";
+			reg = <0x4c>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt
index 4f8ec947c6b..4f8ec947c6b 100644
--- a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
index 1bfc02de1b0..30ac3a0557f 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
@@ -4,6 +4,8 @@ Required properties:
 - compatible: Should be "fsl,<chip>-i2c"
 - reg: Should contain registers location and length
 - interrupts: Should contain ERROR and DMA interrupts
+- clock-frequency: Desired I2C bus clock frequency in Hz.
+                   Only 100000Hz and 400000Hz modes are supported.
 
 Examples:
 
@@ -13,4 +15,5 @@ i2c0: i2c@80058000 {
 	compatible = "fsl,imx28-i2c";
 	reg = <0x80058000 2000>;
 	interrupts = <111 68>;
+	clock-frequency = <100000>;
 };
diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
new file mode 100644
index 00000000000..c15781f4dc8
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
@@ -0,0 +1,33 @@
+Device tree configuration for i2c-ocores
+
+Required properties:
+- compatible      : "opencores,i2c-ocores"
+- reg             : bus address start and address range size of device
+- interrupts      : interrupt number
+- clock-frequency : frequency of bus clock in Hz
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Optional properties:
+- reg-shift       : device register offsets are shifted by this value
+- reg-io-width    : io register width in bytes (1, 2 or 4)
+- regstep         : deprecated, use reg-shift above
+
+Example:
+
+	i2c0: ocores@a0000000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "opencores,i2c-ocores";
+		reg = <0xa0000000 0x8>;
+		interrupts = <10>;
+		clock-frequency = <20000000>;
+
+		reg-shift = <0>;	/* 8 bit registers */
+		reg-io-width = <1>;	/* 8 bit read/write */
+
+		dummy@60 {
+			compatible = "dummy";
+			reg = <0x60>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt
index b891ee21835..0f7945019f6 100644
--- a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt
@@ -1,4 +1,4 @@
-* I2C
+* Marvell MMP I2C controller
 
 Required properties :
 
@@ -32,3 +32,20 @@ Examples:
 		interrupts = <58>;
 	};
 
+* Marvell MV64XXX I2C controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device
+ - compatible      : Should be "marvell,mv64xxx-i2c"
+ - interrupts      : The interrupt number
+ - clock-frequency : Desired I2C bus clock frequency in Hz.
+
+Examples:
+
+	i2c@11000 {
+		compatible = "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x20>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};
diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt
new file mode 100644
index 00000000000..31afd5014c4
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt
@@ -0,0 +1,28 @@
+NXP LPC32xx Key Scan Interface
+
+Required Properties:
+- compatible: Should be "nxp,lpc3220-key"
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+- interrupts: The interrupt number to the cpu.
+- keypad,num-rows: Number of rows and columns, e.g. 1: 1x1, 6: 6x6
+- keypad,num-columns: Must be equal to keypad,num-rows since LPC32xx only
+  supports square matrices
+- nxp,debounce-delay-ms: Debounce delay in ms
+- nxp,scan-delay-ms: Repeated scan period in ms
+- linux,keymap: the key-code to be reported when the key is pressed
+  and released, see also
+  Documentation/devicetree/bindings/input/matrix-keymap.txt
+
+Example:
+
+	key@40050000 {
+		compatible = "nxp,lpc3220-key";
+		reg = <0x40050000 0x1000>;
+		interrupts = <54 0>;
+		keypad,num-rows = <1>;
+		keypad,num-columns = <1>;
+		nxp,debounce-delay-ms = <3>;
+		nxp,scan-delay-ms = <34>;
+		linux,keymap = <0x00000002>;
+	};
diff --git a/Documentation/devicetree/bindings/input/omap-keypad.txt b/Documentation/devicetree/bindings/input/omap-keypad.txt
new file mode 100644
index 00000000000..f2fa5e10493
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/omap-keypad.txt
@@ -0,0 +1,31 @@
+* TI's Keypad Controller device tree bindings
+
+TI's Keypad controller is used to interface a SoC with a matrix-type
+keypad device. The keypad controller supports multiple row and column lines.
+A key can be placed at each intersection of a unique row and a unique column.
+The keypad controller can sense a key-press and key-release and report the
+event using a interrupt to the cpu.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+   - "ti,omap4-keypad": For controllers compatible with omap4 keypad
+      controller.
+
+Required Board Specific Properties, in addition to those specified by
+the shared matrix-keyboard bindings:
+- keypad,num-rows: Number of row lines connected to the keypad
+  controller.
+
+- keypad,num-columns: Number of column lines connected to the
+  keypad controller.
+
+Optional Properties specific to linux:
+- linux,keypad-no-autorepeat: do no enable autorepeat feature.
+
+Example:
+	keypad@4ae1c000{
+		compatible = "ti,omap4-keypad";
+		keypad,num-rows = <2>;
+		keypad,num-columns = <8>;
+		linux,keypad-no-autorepeat;
+	};
diff --git a/Documentation/devicetree/bindings/input/twl6040-vibra.txt b/Documentation/devicetree/bindings/input/twl6040-vibra.txt
deleted file mode 100644
index 5b1918b818f..00000000000
--- a/Documentation/devicetree/bindings/input/twl6040-vibra.txt
+++ /dev/null
@@ -1,37 +0,0 @@
-Vibra driver for the twl6040 family
-
-The vibra driver is a child of the twl6040 MFD dirver.
-Documentation/devicetree/bindings/mfd/twl6040.txt
-
-Required properties:
-- compatible : Must be "ti,twl6040-vibra";
-- interrupts: 4, Vibra overcurrent interrupt
-- vddvibl-supply: Regulator supplying the left vibra motor
-- vddvibr-supply: Regulator supplying the right vibra motor
-- vibldrv_res: Board specific left driver resistance
-- vibrdrv_res: Board specific right driver resistance
-- viblmotor_res: Board specific left motor resistance
-- vibrmotor_res: Board specific right motor resistance
-
-Optional properties:
-- vddvibl_uV: If the vddvibl default voltage need to be changed
-- vddvibr_uV: If the vddvibr default voltage need to be changed
-
-Example:
-/*
- * 8-channel high quality low-power audio codec
- * http://www.ti.com/lit/ds/symlink/twl6040.pdf
- */
-twl6040: twl6040@4b {
-	...
-	twl6040_vibra: twl6040@1 {
-		compatible = "ti,twl6040-vibra";
-		interrupts = <4>;
-		vddvibl-supply = <&vbat>;
-		vddvibr-supply = <&vbat>;
-		vibldrv_res = <8>;
-		vibrdrv_res = <3>;
-		viblmotor_res = <10>;
-		vibrmotor_res = <10>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt
new file mode 100644
index 00000000000..69e757a657a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ab8500.txt
@@ -0,0 +1,123 @@
+* AB8500 Multi-Functional Device (MFD)
+
+Required parent device properties:
+- compatible             : contains "stericsson,ab8500";
+- interrupts             : contains the IRQ line for the AB8500
+- interrupt-controller   : describes the AB8500 as an Interrupt Controller (has its own domain)
+- #interrupt-cells       : should be 2, for 2-cell format
+                            - The first cell is the AB8500 local IRQ number
+                            - The second cell is used to specify optional parameters
+                              - bits[3:0] trigger type and level flags:
+                                  1 = low-to-high edge triggered
+                                  2 = high-to-low edge triggered
+                                  4 = active high level-sensitive
+                                  8 = active low level-sensitive
+
+Optional parent device properties:
+- reg                    : contains the PRCMU mailbox address for the AB8500 i2c port
+
+The AB8500 consists of a large and varied group of sub-devices:
+
+Device                     IRQ Names              Supply Names   Description
+------                     ---------              ------------   -----------
+ab8500-bm                :                      :              : Battery Manager
+ab8500-btemp             :                      :              : Battery Temperature
+ab8500-charger           :                      :              : Battery Charger
+ab8500-fg                :                      :              : Fuel Gauge
+ab8500-gpadc             : HW_CONV_END          : vddadc       : Analogue to Digital Converter
+                           SW_CONV_END          :              :
+ab8500-gpio              :                      :              : GPIO Controller
+ab8500-ponkey            : ONKEY_DBF            :              : Power-on Key
+                           ONKEY_DBR            :              :
+ab8500-pwm               :                      :              : Pulse Width Modulator
+ab8500-regulator         :                      :              : Regulators
+ab8500-rtc               : 60S                  :              : Real Time Clock
+                         : ALARM                :              :
+ab8500-sysctrl           :                      :              : System Control
+ab8500-usb               : ID_WAKEUP_R          : vddulpivio18 : Universal Serial Bus
+                         : ID_WAKEUP_F          : v-ape        :
+                         : VBUS_DET_F           : musb_1v8     :
+                         : VBUS_DET_R           :              :
+                         : USB_LINK_STATUS      :              :
+                         : USB_ADP_PROBE_PLUG   :              :
+                         : USB_ADP_PROBE_UNPLUG :              :
+
+Required child device properties:
+- compatible             : "stericsson,ab8500-[bm|btemp|charger|fg|gpadc|gpio|ponkey|
+                                               pwm|regulator|rtc|sysctrl|usb]";
+
+Optional child device properties:
+- interrupts             : contains the device IRQ(s) using the 2-cell format (see above)
+- interrupt-names        : contains names of IRQ resource in the order in which they were
+                           supplied in the interrupts property
+- <supply_name>-supply   : contains a phandle to the regulator supply node in Device Tree
+
+ab8500@5 {
+         compatible = "stericsson,ab8500";
+         reg = <5>; /* mailbox 5 is i2c */
+         interrupts = <0 40 0x4>;
+         interrupt-controller;
+         #interrupt-cells = <2>;
+
+         ab8500-rtc {
+                 compatible = "stericsson,ab8500-rtc";
+                 interrupts = <17 0x4
+                               18 0x4>;
+                 interrupt-names = "60S", "ALARM";
+         };
+
+        ab8500-gpadc {
+                compatible = "stericsson,ab8500-gpadc";
+                interrupts = <32 0x4
+                              39 0x4>;
+                interrupt-names = "HW_CONV_END", "SW_CONV_END";
+                vddadc-supply = <&ab8500_ldo_tvout_reg>;
+        };
+
+        ab8500-usb {
+                compatible = "stericsson,ab8500-usb";
+                interrupts = < 90 0x4
+                               96 0x4
+                               14 0x4
+                               15 0x4
+                               79 0x4
+                               74 0x4
+                               75 0x4>;
+                interrupt-names = "ID_WAKEUP_R",
+                                  "ID_WAKEUP_F",
+                                  "VBUS_DET_F",
+                                  "VBUS_DET_R",
+                                  "USB_LINK_STATUS",
+                                  "USB_ADP_PROBE_PLUG",
+                                  "USB_ADP_PROBE_UNPLUG";
+                vddulpivio18-supply = <&ab8500_ldo_initcore_reg>;
+                v-ape-supply = <&db8500_vape_reg>;
+                musb_1v8-supply = <&db8500_vsmps2_reg>;
+        };
+
+        ab8500-ponkey {
+                compatible = "stericsson,ab8500-ponkey";
+                interrupts = <6 0x4
+                              7 0x4>;
+                interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+        };
+
+        ab8500-sysctrl {
+                compatible = "stericsson,ab8500-sysctrl";
+        };
+
+        ab8500-pwm {
+                compatible = "stericsson,ab8500-pwm";
+        };
+
+        ab8500-regulators {
+                compatible = "stericsson,ab8500-regulator";
+
+                ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+                        /*
+                         * See: Documentation/devicetree/bindings/regulator/regulator.txt
+                         * for more information on regulators
+                         */
+                };
+        };
+};
diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt
new file mode 100644
index 00000000000..c6a3469d343
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77686.txt
@@ -0,0 +1,59 @@
+Maxim MAX77686 multi-function device
+
+MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is
+interfaced to host controller using i2c interface. PMIC and Charger submodules
+are addressed using same i2c slave address whereas RTC submodule uses
+different i2c slave address,presently for which we are statically creating i2c
+client while probing.This document describes the binding for mfd device and
+PMIC submodule.
+
+Required properties:
+- compatible : Must be "maxim,max77686";
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+- interrupt-parent : The parent interrupt controller.
+
+Optional node:
+- voltage-regulators : The regulators of max77686 have to be instantiated
+  under subnode named "voltage-regulators" using the following format.
+
+	regulator_name {
+		regulator-compatible = LDOn/BUCKn
+		standard regulator constraints....
+	};
+	refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+  The regulator-compatible property of regulator should initialized with string
+to get matched with their hardware counterparts as follow:
+
+	-LDOn 	:	for LDOs, where n can lie in range 1 to 26.
+		 	example: LDO1, LDO2, LDO26.
+	-BUCKn 	:	for BUCKs, where n can lie in range 1 to 9.
+			example: BUCK1, BUCK5, BUCK9.
+
+Example:
+
+	max77686@09 {
+		compatible = "maxim,max77686";
+		interrupt-parent = <&wakeup_eint>;
+		interrupts = <26 0>;
+		reg = <0x09>;
+
+		voltage-regulators {
+			ldo11_reg {
+				regulator-compatible = "LDO11";
+				regulator-name = "vdd_ldo11";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-always-on;
+			};
+
+			buck1_reg {
+				regulator-compatible = "BUCK1";
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+	}
diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt
index d2802d4717b..db03599ae4d 100644
--- a/Documentation/devicetree/bindings/mfd/tps65910.txt
+++ b/Documentation/devicetree/bindings/mfd/tps65910.txt
@@ -81,7 +81,7 @@ Example:
 
 		ti,vmbch-threshold = 0;
 		ti,vmbch2-threshold = 0;
-
+		ti,en-ck32k-xtal;
 		ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
 
 		vcc1-supply = <&reg_parent>;
diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt
index bc67c6f424a..c855240f3a0 100644
--- a/Documentation/devicetree/bindings/mfd/twl6040.txt
+++ b/Documentation/devicetree/bindings/mfd/twl6040.txt
@@ -6,7 +6,7 @@ They are connected ot the host processor via i2c for commands, McPDM for audio
 data and commands.
 
 Required properties:
-- compatible : Must be "ti,twl6040";
+- compatible : "ti,twl6040" for twl6040, "ti,twl6041" for twl6041
 - reg: must be 0x4b for i2c address
 - interrupts: twl6040 has one interrupt line connecteded to the main SoC
 - interrupt-parent: The parent interrupt controller
diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
new file mode 100644
index 00000000000..6581478225a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt
@@ -0,0 +1,126 @@
+* Boot Bus
+
+The Octeon Boot Bus is a configurable parallel bus with 8 chip
+selects.  Each chip select is independently configurable.
+
+Properties:
+- compatible: "cavium,octeon-3860-bootbus"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the Boot Bus' register bank.
+
+- #address-cells: Must be <2>.  The first cell is the chip select
+   within the bootbus.  The second cell is the offset from the chip select.
+
+- #size-cells: Must be <1>.
+
+- ranges: There must be one one triplet of (child-bus-address,
+  parent-bus-address, length) for each active chip select.  If the
+  length element for any triplet is zero, the chip select is disabled,
+  making it inactive.
+
+The configuration parameters for each chip select are stored in child
+nodes.
+
+Configuration Properties:
+- compatible:  "cavium,octeon-3860-bootbus-config"
+
+- cavium,cs-index: A single cell indicating the chip select that
+  corresponds to this configuration.
+
+- cavium,t-adr: A cell specifying the ADR timing (in nS).
+
+- cavium,t-ce: A cell specifying the CE timing (in nS).
+
+- cavium,t-oe: A cell specifying the OE timing (in nS).
+
+- cavium,t-we: A cell specifying the WE timing (in nS).
+
+- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS).
+
+- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS).
+
+- cavium,t-pause: A cell specifying the PAUSE timing (in nS).
+
+- cavium,t-wait: A cell specifying the WAIT timing (in nS).
+
+- cavium,t-page: A cell specifying the PAGE timing (in nS).
+
+- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS).
+
+- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1
+  = 2 bytes, 2 = 4 bytes, 3 = 8 bytes).
+
+- cavium,wait-mode: Optional.  If present, wait mode (WAITM) is selected.
+
+- cavium,page-mode: Optional.  If present, page mode (PAGEM) is selected.
+
+- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of
+  the bus for this chip select.
+
+- cavium,ale-mode: Optional.  If present, ALE mode is selected.
+
+- cavium,sam-mode: Optional.  If present, SAM mode is selected.
+
+- cavium,or-mode: Optional.  If present, OR mode is selected.
+
+Example:
+	bootbus: bootbus@1180000000000 {
+		compatible = "cavium,octeon-3860-bootbus";
+		reg = <0x11800 0x00000000 0x0 0x200>;
+		/* The chip select number and offset */
+		#address-cells = <2>;
+		/* The size of the chip select region */
+		#size-cells = <1>;
+		ranges = <0 0  0x0 0x1f400000  0xc00000>,
+			 <1 0  0x10000 0x30000000  0>,
+			 <2 0  0x10000 0x40000000  0>,
+			 <3 0  0x10000 0x50000000  0>,
+			 <4 0  0x0 0x1d020000  0x10000>,
+			 <5 0  0x0 0x1d040000  0x10000>,
+			 <6 0  0x0 0x1d050000  0x10000>,
+			 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <0>;
+			cavium,t-adr  = <20>;
+			cavium,t-ce   = <60>;
+			cavium,t-oe   = <60>;
+			cavium,t-we   = <45>;
+			cavium,t-rd-hld = <35>;
+			cavium,t-wr-hld = <45>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <35>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,bus-width = <8>;
+		};
+		.
+		.
+		.
+		cavium,cs-config@6 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <6>;
+			cavium,t-adr  = <5>;
+			cavium,t-ce   = <300>;
+			cavium,t-oe   = <270>;
+			cavium,t-we   = <150>;
+			cavium,t-rd-hld = <100>;
+			cavium,t-wr-hld = <70>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <320>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,wait-mode;
+			cavium,bus-width = <16>;
+		};
+		.
+		.
+		.
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu.txt b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
new file mode 100644
index 00000000000..2c2d0746b43
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/ciu.txt
@@ -0,0 +1,26 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-3860-ciu"
+
+  Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+   the CIU and may have a value of 0 or 1.  The second cell is the bit
+   within the bank and may have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070000000000 {
+		compatible = "cavium,octeon-3860-ciu";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0 or 1)
+		 * 2) Bit within the register (0..63)
+		 */
+		#interrupt-cells = <2>;
+		reg = <0x10700 0x00000000 0x0 0x7000>;
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu2.txt b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt
new file mode 100644
index 00000000000..0ec7ba8bbbc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt
@@ -0,0 +1,27 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-6880-ciu2"
+
+  Compatibility with 68XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+  the CIU and may have a value between 0 and 63.  The second cell is
+  the bit within the bank and may also have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070100000000 {
+		compatible = "cavium,octeon-6880-ciu2";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0..63)
+		 * 2) Bit within the register (0..63)
+		 */
+		#address-cells = <0>;
+		#interrupt-cells = <2>;
+		reg = <0x10701 0x00000000 0x0 0x4000000>;
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
new file mode 100644
index 00000000000..cb4291e3b1d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt
@@ -0,0 +1,21 @@
+* DMA Engine.
+
+The Octeon DMA Engine transfers between the Boot Bus and main memory.
+The DMA Engine will be refered to by phandle by any device that is
+connected to it.
+
+Properties:
+- compatible: "cavium,octeon-5750-bootbus-dma"
+
+  Compatibility with all cn52XX, cn56XX and cn6XXX SOCs.
+
+- reg: The base address of the DMA Engine's register bank.
+
+- interrupts: A single interrupt specifier.
+
+Example:
+	dma0: dma-engine@1180000000100 {
+		compatible = "cavium,octeon-5750-bootbus-dma";
+		reg = <0x11800 0x00000100 0x0 0x8>;
+		interrupts = <0 63>;
+	};
diff --git a/Documentation/devicetree/bindings/mips/cavium/uctl.txt b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
new file mode 100644
index 00000000000..aa66b9b8d80
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/uctl.txt
@@ -0,0 +1,46 @@
+* UCTL USB controller glue
+
+Properties:
+- compatible: "cavium,octeon-6335-uctl"
+
+  Compatibility with all cn6XXX SOCs.
+
+- reg: The base address of the UCTL register bank.
+
+- #address-cells: Must be <2>.
+
+- #size-cells: Must be <2>.
+
+- ranges: Empty to signify direct mapping of the children.
+
+- refclk-frequency: A single cell containing the reference clock
+  frequency in Hz.
+
+- refclk-type: A string describing the reference clock connection
+  either "crystal" or "external".
+
+Example:
+	uctl@118006f000000 {
+		compatible = "cavium,octeon-6335-uctl";
+		reg = <0x11800 0x6f000000 0x0 0x100>;
+		ranges; /* Direct mapping */
+		#address-cells = <2>;
+		#size-cells = <2>;
+		/* 12MHz, 24MHz and 48MHz allowed */
+		refclk-frequency = <24000000>;
+		/* Either "crystal" or "external" */
+		refclk-type = "crystal";
+
+		ehci@16f0000000000 {
+			compatible = "cavium,octeon-6335-ehci","usb-ehci";
+			reg = <0x16f00 0x00000000 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+		ohci@16f0000000400 {
+			compatible = "cavium,octeon-6335-ohci","usb-ohci";
+			reg = <0x16f00 0x00000400 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/misc/at25.txt b/Documentation/devicetree/bindings/misc/at25.txt
new file mode 100644
index 00000000000..ab3c327929d
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/at25.txt
@@ -0,0 +1,21 @@
+Atmel AT25 eeprom
+
+Required properties:
+- compatible : "atmel,at25".
+- reg : chip select number
+- spi-max-frequency : max spi frequency to use
+
+- at25,byte-len : total eeprom size in bytes
+- at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h
+- at25,page-size : size of the eeprom page
+
+Examples:
+at25@0 {
+	compatible = "atmel,at25";
+	reg = <0>
+	spi-max-frequency = <5000000>;
+
+	at25,byte-len = <0x8000>;
+	at25,addr-mode = <2>;
+	at25,page-size = <64>;
+};
diff --git a/Documentation/devicetree/bindings/mtd/orion-nand.txt b/Documentation/devicetree/bindings/mtd/orion-nand.txt
index b2356b7d2fa..2d6ab660e60 100644
--- a/Documentation/devicetree/bindings/mtd/orion-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/orion-nand.txt
@@ -1,7 +1,7 @@
 NAND support for Marvell Orion SoC platforms
 
 Required properties:
-- compatible : "mrvl,orion-nand".
+- compatible : "marvell,orion-nand".
 - reg : Base physical address of the NAND and length of memory mapped
 	region
 
@@ -24,7 +24,7 @@ nand@f4000000 {
 	ale = <1>;
 	bank-width = <1>;
 	chip-delay = <25>;
-	compatible = "mrvl,orion-nand";
+	compatible = "marvell,orion-nand";
 	reg = <0xf4000000 0x400>;
 
 	partition@0 {
diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt
new file mode 100644
index 00000000000..04cb7491d23
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt
@@ -0,0 +1,27 @@
+* System Management Interface (SMI) / MDIO
+
+Properties:
+- compatible: "cavium,octeon-3860-mdio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the MDIO bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  MDIO addresses have no size component.
+
+Typically an MDIO bus might have several children.
+
+Example:
+	mdio@1180000001800 {
+		compatible = "cavium,octeon-3860-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x11800 0x00001800 0x0 0x40>;
+
+		ethernet-phy@0 {
+			...
+			reg = <0>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt
new file mode 100644
index 00000000000..5da628db68b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-mix.txt
@@ -0,0 +1,39 @@
+* MIX Ethernet controller.
+
+Properties:
+- compatible: "cavium,octeon-5750-mix"
+
+  Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX
+  devices.
+
+- reg: The base addresses of four separate register banks.  The first
+  bank contains the MIX registers.  The second bank the corresponding
+  AGL registers.  The third bank are the AGL registers shared by all
+  MIX devices present.  The fourth bank is the AGL_PRT_CTL shared by
+  all MIX devices present.
+
+- cell-index: A single cell specifying which portion of the shared
+  register banks corresponds to this MIX device.
+
+- interrupts: Two interrupt specifiers.  The first is the MIX
+  interrupt routing and the second the routing for the AGL interrupts.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+  if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+	ethernet@1070000100800 {
+		compatible = "cavium,octeon-5750-mix";
+		reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+		      <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+		      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+		      <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
+		cell-index = <1>;
+		interrupts = <1 18>, < 1 46>;
+		local-mac-address = [ 00 0f b7 10 63 54 ];
+		phy-handle = <&phy1>;
+	};
diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt
new file mode 100644
index 00000000000..d4c53ba04b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/cavium-pip.txt
@@ -0,0 +1,98 @@
+* PIP Ethernet nexus.
+
+The PIP Ethernet nexus can control several data packet input/output
+devices.  The devices have a two level grouping scheme.  There may be
+several interfaces, and each interface may have several ports.  These
+ports might be an individual Ethernet PHY.
+
+
+Properties for the PIP nexus:
+- compatible: "cavium,octeon-3860-pip"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the PIP's register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP interfaces which is a child the PIP nexus:
+- compatible: "cavium,octeon-3860-pip-interface"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The interface number.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP port which is a child the PIP interface:
+- compatible: "cavium,octeon-3860-pip-port"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The port number within the interface group.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+  if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+
+	pip@11800a0000000 {
+		compatible = "cavium,octeon-3860-pip";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+		interface@0 {
+			compatible = "cavium,octeon-3860-pip-interface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>; /* interface */
+
+			ethernet@0 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x0>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 60 ];
+				phy-handle = <&phy2>;
+			};
+			ethernet@1 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x1>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 61 ];
+				phy-handle = <&phy3>;
+			};
+			ethernet@2 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x2>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 62 ];
+				phy-handle = <&phy4>;
+			};
+			ethernet@3 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x3>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 63 ];
+				phy-handle = <&phy5>;
+			};
+		};
+
+		interface@1 {
+			compatible = "cavium,octeon-3860-pip-interface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>; /* interface */
+
+			ethernet@0 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x0>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 64 ];
+				phy-handle = <&phy6>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt
new file mode 100644
index 00000000000..cfe1db3bb6e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt
@@ -0,0 +1,12 @@
+LPC32XX PWM controller
+
+Required properties:
+- compatible: should be "nxp,lpc3220-pwm"
+- reg: physical base address and length of the controller's registers
+
+Examples:
+
+pwm@0x4005C000 {
+	compatible = "nxp,lpc3220-pwm";
+	reg = <0x4005C000 0x8>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
new file mode 100644
index 00000000000..b16f4a57d11
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
@@ -0,0 +1,17 @@
+Freescale MXS PWM controller
+
+Required properties:
+- compatible: should be "fsl,imx23-pwm"
+- reg: physical base address and length of the controller's registers
+- #pwm-cells: should be 2.  The first cell specifies the per-chip index
+  of the PWM to use and the second cell is the duty cycle in nanoseconds.
+- fsl,pwm-number: the number of PWM devices
+
+Example:
+
+pwm: pwm@80064000 {
+	compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
+	reg = <0x80064000 2000>;
+	#pwm-cells = <2>;
+	fsl,pwm-number = <8>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
new file mode 100644
index 00000000000..bbbeedb4ec0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
@@ -0,0 +1,18 @@
+Tegra SoC PWFM controller
+
+Required properties:
+- compatible: should be one of:
+  - "nvidia,tegra20-pwm"
+  - "nvidia,tegra30-pwm"
+- reg: physical base address and length of the controller's registers
+- #pwm-cells: On Tegra the number of cells used to specify a PWM is 2. The
+  first cell specifies the per-chip index of the PWM to use and the second
+  cell is the duty cycle in nanoseconds.
+
+Example:
+
+	pwm: pwm@7000a000 {
+		compatible = "nvidia,tegra20-pwm";
+		reg = <0x7000a000 0x100>;
+		#pwm-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt
new file mode 100644
index 00000000000..73ec962bfe8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm.txt
@@ -0,0 +1,57 @@
+Specifying PWM information for devices
+======================================
+
+1) PWM user nodes
+-----------------
+
+PWM users should specify a list of PWM devices that they want to use
+with a property containing a 'pwm-list':
+
+	pwm-list ::= <single-pwm> [pwm-list]
+	single-pwm ::= <pwm-phandle> <pwm-specifier>
+	pwm-phandle : phandle to PWM controller node
+	pwm-specifier : array of #pwm-cells specifying the given PWM
+			(controller specific)
+
+PWM properties should be named "pwms". The exact meaning of each pwms
+property must be documented in the device tree binding for each device.
+An optional property "pwm-names" may contain a list of strings to label
+each of the PWM devices listed in the "pwms" property. If no "pwm-names"
+property is given, the name of the user node will be used as fallback.
+
+Drivers for devices that use more than a single PWM device can use the
+"pwm-names" property to map the name of the PWM device requested by the
+pwm_get() call to an index into the list given by the "pwms" property.
+
+The following example could be used to describe a PWM-based backlight
+device:
+
+	pwm: pwm {
+		#pwm-cells = <2>;
+	};
+
+	[...]
+
+	bl: backlight {
+		pwms = <&pwm 0 5000000>;
+		pwm-names = "backlight";
+	};
+
+pwm-specifier typically encodes the chip-relative PWM number and the PWM
+period in nanoseconds. Note that in the example above, specifying the
+"pwm-names" is redundant because the name "backlight" would be used as
+fallback anyway.
+
+2) PWM controller nodes
+-----------------------
+
+PWM controller nodes must specify the number of cells used for the
+specifier using the '#pwm-cells' property.
+
+An example PWM controller might look like this:
+
+	pwm: pwm@7000a000 {
+		compatible = "nvidia,tegra20-pwm";
+		reg = <0x7000a000 0x100>;
+		#pwm-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/serial/cavium-uart.txt b/Documentation/devicetree/bindings/serial/cavium-uart.txt
new file mode 100644
index 00000000000..87a6c375cd4
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/cavium-uart.txt
@@ -0,0 +1,19 @@
+* Universal Asynchronous Receiver/Transmitter (UART)
+
+- compatible: "cavium,octeon-3860-uart"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the UART register bank.
+
+- interrupts: A single interrupt specifier.
+
+- current-speed: Optional, the current bit rate in bits per second.
+
+Example:
+	uart1: serial@1180000000c00 {
+		compatible = "cavium,octeon-3860-uart","ns16550";
+		reg = <0x11800 0x00000c00 0x0 0x400>;
+		current-speed = <115200>;
+		interrupts = <0 35>;
+	};
diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt
new file mode 100644
index 00000000000..a3ff50fc76f
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-orion.txt
@@ -0,0 +1,19 @@
+Marvell Orion SPI device
+
+Required properties:
+- compatible : should be "marvell,orion-spi".
+- reg : offset and length of the register set for the device
+- cell-index : Which of multiple SPI controllers is this.
+Optional properties:
+- interrupts : Is currently not used.
+
+Example:
+       spi@10600 {
+	       compatible = "marvell,orion-spi";
+	       #address-cells = <1>;
+	       #size-cells = <0>;
+	       cell-index = <0>;
+	       reg = <0x10600 0x28>;
+	       interrupts = <23>;
+	       status = "disabled";
+       };
diff --git a/Documentation/devicetree/bindings/thermal/spear-thermal.txt b/Documentation/devicetree/bindings/thermal/spear-thermal.txt
new file mode 100644
index 00000000000..93e3b67c102
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/spear-thermal.txt
@@ -0,0 +1,14 @@
+* SPEAr Thermal
+
+Required properties:
+- compatible : "st,thermal-spear1340"
+- reg : Address range of the thermal registers
+- st,thermal-flags: flags used to enable thermal sensor
+
+Example:
+
+	thermal@fc000000 {
+		compatible = "st,thermal-spear1340";
+		reg = <0xfc000000 0x1000>;
+		st,thermal-flags = <0x7000>;
+	};
diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
index b8b27b0aca1..0847fdeee11 100644
--- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
@@ -9,6 +9,7 @@ Required properties:
 	- "ns16750"
 	- "ns16850"
 	- "nvidia,tegra20-uart"
+	- "nxp,lpc3220-uart"
 	- "ibm,qpace-nwp-serial"
 	- "serial" if the port type is unknown.
 - reg : offset and length of the register set for the device.
diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
new file mode 100644
index 00000000000..2c290418bb2
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt
@@ -0,0 +1,18 @@
+* Freescale i.MX ci13xxx usb controllers
+
+Required properties:
+- compatible: Should be "fsl,imx27-usb"
+- reg: Should contain registers location and length
+- interrupts: Should contain controller interrupt
+
+Optional properties:
+- fsl,usbphy: phandler of usb phy that connects to the only one port
+- vbus-supply: regulator for vbus
+
+Examples:
+usb@02184000 { /* USB OTG */
+	compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+	reg = <0x02184000 0x200>;
+	interrupts = <0 43 0x04>;
+	fsl,usbphy = <&usbphy1>;
+};
diff --git a/Documentation/devicetree/bindings/usb/mxs-phy.txt b/Documentation/devicetree/bindings/usb/mxs-phy.txt
new file mode 100644
index 00000000000..5835b27146e
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mxs-phy.txt
@@ -0,0 +1,13 @@
+* Freescale MXS USB Phy Device
+
+Required properties:
+- compatible: Should be "fsl,imx23-usbphy"
+- reg: Should contain registers location and length
+- interrupts: Should contain phy interrupt
+
+Example:
+usbphy1: usbphy@020c9000 {
+	compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
+	reg = <0x020c9000 0x1000>;
+	interrupts = <0 44 0x04>;
+};
diff --git a/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt
new file mode 100644
index 00000000000..1e4fc727f3b
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt
@@ -0,0 +1,28 @@
+pwm-backlight bindings
+
+Required properties:
+  - compatible: "pwm-backlight"
+  - pwms: OF device-tree PWM specification (see PWM binding[0])
+  - brightness-levels: Array of distinct brightness levels. Typically these
+      are in the range from 0 to 255, but any range starting at 0 will do.
+      The actual brightness level (PWM duty cycle) will be interpolated
+      from these values. 0 means a 0% duty cycle (darkest/off), while the
+      last value in the array represents a 100% duty cycle (brightest).
+  - default-brightness-level: the default brightness level (index into the
+      array defined by the "brightness-levels" property)
+
+Optional properties:
+  - pwm-names: a list of names for the PWM devices specified in the
+               "pwms" property (see PWM binding[0])
+
+[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+
+Example:
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};