move frv docs one level up

My first guess for "fujitsu" was it might be related to the
fujitsu-laptop.c driver...

Move the frv directory one level up since frv is the name of the
architecture in the Linux kernel.

Signed-off-by: Adrian Bunk <bunk@kernel.org>

1 files changed, 310 insertions, 0 deletions

diff --git a/Documentation/frv/features.txt b/Documentation/frv/features.txt
new file mode 100644
index 00000000000..fa20c0e7283
--- /dev/null
+++ b/Documentation/frv/features.txt
@@ -0,0 +1,310 @@
+			 ===========================
+			 FUJITSU FR-V LINUX FEATURES
+			 ===========================
+
+This kernel port has a number of features of which the user should be aware:
+
+ (*) Linux and uClinux
+
+     The FR-V architecture port supports both normal MMU linux and uClinux out
+     of the same sources.
+
+
+ (*) CPU support
+
+     Support for the FR401, FR403, FR405, FR451 and FR555 CPUs should work with
+     the same uClinux kernel configuration.
+
+     In normal (MMU) Linux mode, only the FR451 CPU will work as that is the
+     only one with a suitably featured CPU.
+
+     The kernel is written and compiled with the assumption that only the
+     bottom 32 GR registers and no FR registers will be used by the kernel
+     itself, however all extra userspace registers will be saved on context
+     switch. Note that since most CPUs can't support lazy switching, no attempt
+     is made to do lazy register saving where that would be possible (FR555
+     only currently).
+
+
+ (*) Board support
+
+     The board on which the kernel will run can be configured on the "Processor
+     type and features" configuration tab.
+
+     Set the System to "MB93093-PDK" to boot from the MB93093 (FR403) PDK.
+
+     Set the System to "MB93091-VDK" to boot from the CB11, CB30, CB41, CB60,
+     CB70 or CB451 VDK boards. Set the Motherboard setting to "MB93090-MB00" to
+     boot with the standard ATA90590B VDK motherboard, and set it to "None" to
+     boot without any motherboard.
+
+
+ (*) Binary Formats
+
+     The only userspace binary format supported is FDPIC ELF. Normal ELF, FLAT
+     and AOUT binaries are not supported for this architecture.
+
+     FDPIC ELF supports shared library and program interpreter facilities.
+
+
+ (*) Scheduler Speed
+
+     The kernel scheduler runs at 100Hz irrespective of the clock speed on this
+     architecture. This value is set in asm/param.h (see the HZ macro defined
+     there).
+
+
+ (*) Normal (MMU) Linux Memory Layout.
+
+     See mmu-layout.txt in this directory for a description of the normal linux
+     memory layout
+
+     See include/asm-frv/mem-layout.h for constants pertaining to the memory
+     layout.
+
+     See include/asm-frv/mb-regs.h for the constants pertaining to the I/O bus
+     controller configuration.
+
+
+ (*) uClinux Memory Layout
+
+     The memory layout used by the uClinux kernel is as follows:
+
+	0x00000000 - 0x00000FFF		Null pointer catch page
+	0x20000000 - 0x200FFFFF CS2#    [PDK] FPGA
+	0xC0000000 - 0xCFFFFFFF		SDRAM
+	0xC0000000			Base of Linux kernel image
+	0xE0000000 - 0xEFFFFFFF	CS2#	[VDK] SLBUS/PCI window
+	0xF0000000 - 0xF0FFFFFF	CS5#	MB93493 CSC area (DAV daughter board)
+	0xF1000000 - 0xF1FFFFFF	CS7#	[CB70/CB451] CPU-card PCMCIA port space
+	0xFC000000 - 0xFC0FFFFF	CS1#	[VDK] MB86943 config space
+	0xFC100000 - 0xFC1FFFFF	CS6#	[CB70/CB451] CPU-card DM9000 NIC space
+	0xFC100000 - 0xFC1FFFFF	CS6#	[PDK] AX88796 NIC space
+	0xFC200000 - 0xFC2FFFFF	CS3#	MB93493 CSR area (DAV daughter board)
+	0xFD000000 - 0xFDFFFFFF	CS4#	[CB70/CB451] CPU-card extra flash space
+	0xFE000000 - 0xFEFFFFFF		Internal CPU peripherals
+	0xFF000000 - 0xFF1FFFFF	CS0#	Flash 1
+	0xFF200000 - 0xFF3FFFFF	CS0#	Flash 2
+	0xFFC00000 - 0xFFC0001F	CS0#	[VDK] FPGA
+
+     The kernel reads the size of the SDRAM from the memory bus controller
+     registers by default.
+
+     The kernel initialisation code (1) adjusts the SDRAM base addresses to
+     move the SDRAM to desired address, (2) moves the kernel image down to the
+     bottom of SDRAM, (3) adjusts the bus controller registers to move I/O
+     windows, and (4) rearranges the protection registers to protect all of
+     this.
+
+     The reasons for doing this are: (1) the page at address 0 should be
+     inaccessible so that NULL pointer errors can be caught; and (2) the bottom
+     three quarters are left unoccupied so that an FR-V CPU with an MMU can use
+     it for virtual userspace mappings.
+
+     See include/asm-frv/mem-layout.h for constants pertaining to the memory
+     layout.
+
+     See include/asm-frv/mb-regs.h for the constants pertaining to the I/O bus
+     controller configuration.
+
+
+ (*) uClinux Memory Protection
+
+     A DAMPR register is used to cover the entire region used for I/O
+     (0xE0000000 - 0xFFFFFFFF). This permits the kernel to make uncached
+     accesses to this region. Userspace is not permitted to access it.
+
+     The DAMPR/IAMPR protection registers not in use for any other purpose are
+     tiled over the top of the SDRAM such that:
+
+	(1) The core kernel image is covered by as small a tile as possible
+            granting only the kernel access to the underlying data, whilst
+            making sure no SDRAM is actually made unavailable by this approach.
+
+	(2) All other tiles are arranged to permit userspace access to the rest
+            of the SDRAM.
+
+     Barring point (1), there is nothing to protect kernel data against
+     userspace damage - but this is uClinux.
+
+
+ (*) Exceptions and Fixups
+
+     Since the FR40x and FR55x CPUs that do not have full MMUs generate
+     imprecise data error exceptions, there are currently no automatic fixup
+     services available in uClinux. This includes misaligned memory access
+     fixups.
+
+     Userspace EFAULT errors can be trapped by issuing a MEMBAR instruction and
+     forcing the fault to happen there.
+
+     On the FR451, however, data exceptions are mostly precise, and so
+     exception fixup handling is implemented as normal.
+
+
+ (*) Userspace Breakpoints
+
+     The ptrace() system call supports the following userspace debugging
+     features:
+
+	(1) Hardware assisted single step.
+
+	(2) Breakpoint via the FR-V "BREAK" instruction.
+
+	(3) Breakpoint via the FR-V "TIRA GR0, #1" instruction.
+
+	(4) Syscall entry/exit trap.
+
+     Each of the above generates a SIGTRAP.
+
+
+ (*) On-Chip Serial Ports
+
+     The FR-V on-chip serial ports are made available as ttyS0 and ttyS1. Note
+     that if the GDB stub is compiled in, ttyS1 will not actually be available
+     as it will be being used for the GDB stub.
+
+     These ports can be made by:
+
+	mknod /dev/ttyS0 c 4 64
+	mknod /dev/ttyS1 c 4 65
+
+
+ (*) Maskable Interrupts
+
+     Level 15 (Non-maskable) interrupts are dealt with by the GDB stub if
+     present, and cause a panic if not. If the GDB stub is present, ttyS1's
+     interrupts are rated at level 15.
+
+     All other interrupts are distributed over the set of available priorities
+     so that no IRQs are shared where possible. The arch interrupt handling
+     routines attempt to disentangle the various sources available through the
+     CPU's own multiplexor, and those on off-CPU peripherals.
+
+
+ (*) Accessing PCI Devices
+
+     Where PCI is available, care must be taken when dealing with drivers that
+     access PCI devices. PCI devices present their data in little-endian form,
+     but the CPU sees it in big-endian form. The macros in asm/io.h try to get
+     this right, but may not under all circumstances...
+
+
+ (*) Ax88796 Ethernet Driver
+
+     The MB93093 PDK board has an Ax88796 ethernet chipset (an NE2000 clone). A
+     driver has been written to deal specifically with this. The driver
+     provides MII services for the card.
+
+     The driver can be configured by running make xconfig, and going to:
+
+	(*) Network device support
+	    - turn on "Network device support"
+	    (*) Ethernet (10 or 100Mbit)
+		- turn on "Ethernet (10 or 100Mbit)"
+		- turn on "AX88796 NE2000 compatible chipset"
+
+     The driver can be found in:
+
+	drivers/net/ax88796.c
+	include/asm/ax88796.h
+
+
+ (*) WorkRAM Driver
+
+     This driver provides a character device that permits access to the WorkRAM
+     that can be found on the FR451 CPU. Each page is accessible through a
+     separate minor number, thereby permitting each page to have its own
+     filesystem permissions set on the device file.
+
+     The device files should be:
+
+	mknod /dev/frv/workram0 c 240 0
+	mknod /dev/frv/workram1 c 240 1
+	mknod /dev/frv/workram2 c 240 2
+	...
+
+     The driver will not permit the opening of any device file that does not
+     correspond to at least a partial page of WorkRAM. So the first device file
+     is the only one available on the FR451. If any other CPU is detected, none
+     of the devices will be openable.
+
+     The devices can be accessed with read, write and llseek, and can also be
+     mmapped. If they're mmapped, they will only map at the appropriate
+     0x7e8nnnnn address on linux and at the 0xfe8nnnnn address on uClinux. If
+     MAP_FIXED is not specified, the appropriate address will be chosen anyway.
+
+     The mappings must be MAP_SHARED not MAP_PRIVATE, and must not be
+     PROT_EXEC. They must also start at file offset 0, and must not be longer
+     than one page in size.
+
+     This driver can be configured by running make xconfig, and going to:
+
+	(*) Character devices
+	    - turn on "Fujitsu FR-V CPU WorkRAM support"
+
+
+ (*) Dynamic data cache write mode changing
+
+     It is possible to view and to change the data cache's write mode through
+     the /proc/sys/frv/cache-mode file while the kernel is running. There are
+     two modes available:
+
+	NAME	MEANING
+	=====	==========================================
+	wthru	Data cache is in Write-Through mode
+	wback	Data cache is in Write-Back/Copy-Back mode
+
+     To read the cache mode:
+
+	# cat /proc/sys/frv/cache-mode
+	wthru
+
+     To change the cache mode:
+
+	# echo wback >/proc/sys/frv/cache-mode
+	# cat /proc/sys/frv/cache-mode
+	wback
+
+
+ (*) MMU Context IDs and Pinning
+
+     On MMU Linux the CPU supports the concept of a context ID in its MMU to
+     make it more efficient (TLB entries are labelled with a context ID to link
+     them to specific tasks).
+
+     Normally once a context ID is allocated, it will remain affixed to a task
+     or CLONE_VM'd group of tasks for as long as it exists. However, since the
+     kernel is capable of supporting more tasks than there are possible ID
+     numbers, the kernel will pass context IDs from one task to another if
+     there are insufficient available.
+
+     The context ID currently in use by a task can be viewed in /proc:
+
+	# grep CXNR /proc/1/status
+	CXNR: 1
+
+     Note that kernel threads do not have a userspace context, and so will not
+     show a CXNR entry in that file.
+
+     Under some circumstances, however, it is desirable to pin a context ID on
+     a process such that the kernel won't pass it on. This can be done by
+     writing the process ID of the target process to a special file:
+
+	# echo 17 >/proc/sys/frv/pin-cxnr
+
+     Reading from the file will then show the context ID pinned.
+
+	# cat /proc/sys/frv/pin-cxnr
+	4
+
+     The context ID will remain pinned as long as any process is using that
+     context, i.e.: when the all the subscribing processes have exited or
+     exec'd; or when an unpinning request happens:
+
+	# echo 0 >/proc/sys/frv/pin-cxnr
+
+     When there isn't a pinned context, the file shows -1:
+
+	# cat /proc/sys/frv/pin-cxnr
+	-1