hwmon: Add support for newer uGuru's

This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.

Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

1 files changed, 18 insertions, 13 deletions

diff --git a/Documentation/hwmon/abituguru b/Documentation/hwmon/abituguru
index b2c0d61b39a..87ffa0f5ec7 100644
--- a/Documentation/hwmon/abituguru
+++ b/Documentation/hwmon/abituguru
@@ -2,7 +2,7 @@ Kernel driver abituguru
 =======================
 
 Supported chips:
-  * Abit uGuru revision 1-3 (Hardware Monitor part only)
+  * Abit uGuru revision 1 & 2 (Hardware Monitor part only)
     Prefix: 'abituguru'
     Addresses scanned: ISA 0x0E0
     Datasheet: Not available, this driver is based on reverse engineering.
@@ -20,8 +20,8 @@ Supported chips:
 	uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
 	uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty)
 	uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
-	uGuru 3.0.0.0 ~ 3.0.1.2 (AW8, AL8, NI8)
-	uGuru 4.xxxxx?          (AT8 32X) (2)
+	uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X,
+				 AW9D-MAX) (2)
 	1) For revisions 2 and 3 uGuru's the driver can autodetect the
 	   sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's
 	   this doesnot always work. For these uGuru's the autodection can
@@ -30,8 +30,9 @@ Supported chips:
 	   bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1
 	   You may also need to specify the fan_sensors option for these boards
 	   fan_sensors=5
-	2) The current version of the abituguru driver is known to NOT work
-	   on these Motherboards
+	2) There is a seperate abituguru3 driver for these motherboards,
+	   the abituguru (without the 3 !) driver will not work on these
+	   motherboards (and visa versa)!
 
 Authors:
 	Hans de Goede <j.w.r.degoede@hhs.nl>,
@@ -43,8 +44,10 @@ Module Parameters
 -----------------
 
 * force: bool		Force detection. Note this parameter only causes the
-			detection to be skipped, if the uGuru can't be read
-			the module initialization (insmod) will still fail.
+			detection to be skipped, and thus the insmod to
+			succeed. If the uGuru can't be read the actual hwmon
+			driver will not load and thus no hwmon device will get
+			registered.
 * bank1_types: int[]	Bank1 sensortype autodetection override:
 			  -1 autodetect (default)
 			   0 volt sensor
@@ -69,13 +72,15 @@ dmesg | grep abituguru
 Description
 -----------
 
-This driver supports the hardware monitoring features of the Abit uGuru chip
-found on Abit uGuru featuring motherboards (most modern Abit motherboards).
+This driver supports the hardware monitoring features of the first and
+second revision of the Abit uGuru chip found on Abit uGuru featuring
+motherboards (most modern Abit motherboards).
 
-The uGuru chip in reality is a Winbond W83L950D in disguise (despite Abit
-claiming it is "a new microprocessor designed by the ABIT Engineers").
-Unfortunatly this doesn't help since the W83L950D is a generic
-microcontroller with a custom Abit application running on it.
+The first and second revision of the uGuru chip in reality is a Winbond
+W83L950D in disguise (despite Abit claiming it is "a new microprocessor
+designed by the ABIT Engineers"). Unfortunatly this doesn't help since the
+W83L950D is a generic microcontroller with a custom Abit application running
+on it.
 
 Despite Abit not releasing any information regarding the uGuru, Olle
 Sandberg <ollebull@gmail.com> has managed to reverse engineer the sensor part