Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 76 insertions, 0 deletions

diff --git a/Documentation/i2c/i2c-protocol b/Documentation/i2c/i2c-protocol
new file mode 100644
index 00000000000..b4022c91421
--- /dev/null
+++ b/Documentation/i2c/i2c-protocol
@@ -0,0 +1,76 @@
+This document describes the i2c protocol. Or will, when it is finished :-)
+
+Key to symbols
+==============
+
+S     (1 bit) : Start bit
+P     (1 bit) : Stop bit
+Rd/Wr (1 bit) : Read/Write bit. Rd equals 1, Wr equals 0.
+A, NA (1 bit) : Accept and reverse accept bit. 
+Addr  (7 bits): I2C 7 bit address. Note that this can be expanded as usual to 
+                get a 10 bit I2C address.
+Comm  (8 bits): Command byte, a data byte which often selects a register on
+                the device.
+Data  (8 bits): A plain data byte. Sometimes, I write DataLow, DataHigh
+                for 16 bit data.
+Count (8 bits): A data byte containing the length of a block operation.
+
+[..]: Data sent by I2C device, as opposed to data sent by the host adapter.
+
+
+Simple send transaction
+======================
+
+This corresponds to i2c_master_send.
+
+  S Addr Wr [A] Data [A] Data [A] ... [A] Data [A] P
+
+
+Simple receive transaction
+===========================
+
+This corresponds to i2c_master_recv
+
+  S Addr Rd [A] [Data] A [Data] A ... A [Data] NA P
+
+
+Combined transactions
+====================
+
+This corresponds to i2c_transfer
+
+They are just like the above transactions, but instead of a stop bit P
+a start bit S is sent and the transaction continues. An example of
+a byte read, followed by a byte write:
+
+  S Addr Rd [A] [Data] NA S Addr Wr [A] Data [A] P
+
+
+Modified transactions
+=====================
+
+We have found some I2C devices that needs the following modifications:
+
+  Flag I2C_M_NOSTART: 
+    In a combined transaction, no 'S Addr Wr/Rd [A]' is generated at some
+    point. For example, setting I2C_M_NOSTART on the second partial message
+    generates something like:
+      S Addr Rd [A] [Data] NA Data [A] P
+    If you set the I2C_M_NOSTART variable for the first partial message,
+    we do not generate Addr, but we do generate the startbit S. This will
+    probably confuse all other clients on your bus, so don't try this.
+
+  Flags I2C_M_REV_DIR_ADDR
+    This toggles the Rd/Wr flag. That is, if you want to do a write, but
+    need to emit an Rd instead of a Wr, or vice versa, you set this
+    flag. For example:
+      S Addr Rd [A] Data [A] Data [A] ... [A] Data [A] P
+
+  Flags I2C_M_IGNORE_NAK
+    Normally message is interrupted immediately if there is [NA] from the
+    client. Setting this flag treats any [NA] as [A], and all of
+    message is sent.
+    These messages may still fail to SCL lo->hi timeout.
+
+  Flags I2C_M_NO_RD_ACK
+    In a read message, master A/NA bit is skipped.