summaryrefslogtreecommitdiffstats
path: root/Documentation/networking/framerelay.txt
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
committerLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
commit1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 (patch)
tree0bba044c4ce775e45a88a51686b5d9f90697ea9d /Documentation/networking/framerelay.txt
Linux-2.6.12-rc2v2.6.12-rc2
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
Diffstat (limited to 'Documentation/networking/framerelay.txt')
-rw-r--r--Documentation/networking/framerelay.txt39
1 files changed, 39 insertions, 0 deletions
diff --git a/Documentation/networking/framerelay.txt b/Documentation/networking/framerelay.txt
new file mode 100644
index 00000000000..1a0b720440d
--- /dev/null
+++ b/Documentation/networking/framerelay.txt
@@ -0,0 +1,39 @@
+Frame Relay (FR) support for linux is built into a two tiered system of device
+drivers. The upper layer implements RFC1490 FR specification, and uses the
+Data Link Connection Identifier (DLCI) as its hardware address. Usually these
+are assigned by your network supplier, they give you the number/numbers of
+the Virtual Connections (VC) assigned to you.
+
+Each DLCI is a point-to-point link between your machine and a remote one.
+As such, a separate device is needed to accommodate the routing. Within the
+net-tools archives is 'dlcicfg'. This program will communicate with the
+base "DLCI" device, and create new net devices named 'dlci00', 'dlci01'...
+The configuration script will ask you how many DLCIs you need, as well as
+how many DLCIs you want to assign to each Frame Relay Access Device (FRAD).
+
+The DLCI uses a number of function calls to communicate with the FRAD, all
+of which are stored in the FRAD's private data area. assoc/deassoc,
+activate/deactivate and dlci_config. The DLCI supplies a receive function
+to the FRAD to accept incoming packets.
+
+With this initial offering, only 1 FRAD driver is available. With many thanks
+to Sangoma Technologies, David Mandelstam & Gene Kozin, the S502A, S502E &
+S508 are supported. This driver is currently set up for only FR, but as
+Sangoma makes more firmware modules available, it can be updated to provide
+them as well.
+
+Configuration of the FRAD makes use of another net-tools program, 'fradcfg'.
+This program makes use of a configuration file (which dlcicfg can also read)
+to specify the types of boards to be configured as FRADs, as well as perform
+any board specific configuration. The Sangoma module of fradcfg loads the
+FR firmware into the card, sets the irq/port/memory information, and provides
+an initial configuration.
+
+Additional FRAD device drivers can be added as hardware is available.
+
+At this time, the dlcicfg and fradcfg programs have not been incorporated into
+the net-tools distribution. They can be found at ftp.invlogic.com, in
+/pub/linux. Note that with OS/2 FTPD, you end up in /pub by default, so just
+use 'cd linux'. v0.10 is for use on pre-2.0.3 and earlier, v0.15 is for
+pre-2.0.4 and later.
+