Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 657 insertions, 0 deletions

diff --git a/Documentation/networking/z8530drv.txt b/Documentation/networking/z8530drv.txt
new file mode 100644
index 00000000000..2206abbc3e1
--- /dev/null
+++ b/Documentation/networking/z8530drv.txt
@@ -0,0 +1,657 @@
+This is a subset of the documentation. To use this driver you MUST have the
+full package from:
+
+Internet:
+=========
+
+1. ftp://ftp.ccac.rwth-aachen.de/pub/jr/z8530drv-utils_3.0-3.tar.gz
+
+2. ftp://ftp.pspt.fi/pub/ham/linux/ax25/z8530drv-utils_3.0-3.tar.gz
+
+Please note that the information in this document may be hopelessly outdated.
+A new version of the documentation, along with links to other important
+Linux Kernel AX.25 documentation and programs, is available on
+http://yaina.de/jreuter
+
+-----------------------------------------------------------------------------
+
+
+	 SCC.C - Linux driver for Z8530 based HDLC cards for AX.25      
+
+   ********************************************************************
+
+        (c) 1993,2000 by Joerg Reuter DL1BKE <jreuter@yaina.de>
+
+        portions (c) 1993 Guido ten Dolle PE1NNZ
+
+        for the complete copyright notice see >> Copying.Z8530DRV <<
+
+   ******************************************************************** 
+
+
+1. Initialization of the driver
+===============================
+
+To use the driver, 3 steps must be performed:
+
+     1. if compiled as module: loading the module
+     2. Setup of hardware, MODEM and KISS parameters with sccinit
+     3. Attach each channel to the Linux kernel AX.25 with "ifconfig"
+
+Unlike the versions below 2.4 this driver is a real network device
+driver. If you want to run xNOS instead of our fine kernel AX.25
+use a 2.x version (available from above sites) or read the
+AX.25-HOWTO on how to emulate a KISS TNC on network device drivers.
+
+
+1.1 Loading the module
+======================
+
+(If you're going to compile the driver as a part of the kernel image,
+ skip this chapter and continue with 1.2)
+
+Before you can use a module, you'll have to load it with
+
+	insmod scc.o
+
+please read 'man insmod' that comes with module-init-tools.
+
+You should include the insmod in one of the /etc/rc.d/rc.* files,
+and don't forget to insert a call of sccinit after that. It
+will read your /etc/z8530drv.conf.
+
+1.2. /etc/z8530drv.conf
+=======================
+
+To setup all parameters you must run /sbin/sccinit from one
+of your rc.*-files. This has to be done BEFORE you can
+"ifconfig" an interface. Sccinit reads the file /etc/z8530drv.conf
+and sets the hardware, MODEM and KISS parameters. A sample file is
+delivered with this package. Change it to your needs.
+
+The file itself consists of two main sections.
+
+1.2.1 configuration of hardware parameters
+==========================================
+
+The hardware setup section defines the following parameters for each
+Z8530:
+
+chip    1
+data_a  0x300                   # data port A
+ctrl_a  0x304                   # control port A
+data_b  0x301                   # data port B
+ctrl_b  0x305                   # control port B
+irq     5                       # IRQ No. 5
+pclock  4915200                 # clock
+board   BAYCOM                  # hardware type
+escc    no                      # enhanced SCC chip? (8580/85180/85280)
+vector  0                       # latch for interrupt vector
+special no                      # address of special function register
+option  0                       # option to set via sfr
+
+
+chip	- this is just a delimiter to make sccinit a bit simpler to
+	  program. A parameter has no effect.
+
+data_a  - the address of the data port A of this Z8530 (needed)
+ctrl_a  - the address of the control port A (needed)
+data_b  - the address of the data port B (needed)
+ctrl_b  - the address of the control port B (needed)
+
+irq     - the used IRQ for this chip. Different chips can use different
+          IRQs or the same. If they share an interrupt, it needs to be
+	  specified within one chip-definition only.
+
+pclock  - the clock at the PCLK pin of the Z8530 (option, 4915200 is
+          default), measured in Hertz
+
+board   - the "type" of the board:
+
+	   SCC type                 value
+	   ---------------------------------
+	   PA0HZP SCC card          PA0HZP
+	   EAGLE card               EAGLE
+	   PC100 card               PC100
+	   PRIMUS-PC (DG9BL) card   PRIMUS
+	   BayCom (U)SCC card       BAYCOM
+
+escc    - if you want support for ESCC chips (8580, 85180, 85280), set
+          this to "yes" (option, defaults to "no")
+
+vector  - address of the vector latch (aka "intack port") for PA0HZP
+          cards. There can be only one vector latch for all chips!
+	  (option, defaults to 0)
+
+special - address of the special function register on several cards.
+          (option, defaults to 0)
+
+option  - The value you write into that register (option, default is 0)
+
+You can specify up to four chips (8 channels). If this is not enough,
+just change
+
+	#define MAXSCC 4
+
+to a higher value.
+
+Example for the BAYCOM USCC:
+----------------------------
+
+chip    1
+data_a  0x300                   # data port A
+ctrl_a  0x304                   # control port A
+data_b  0x301                   # data port B
+ctrl_b  0x305                   # control port B
+irq     5                       # IRQ No. 5 (#)
+board   BAYCOM                  # hardware type (*)
+#
+# SCC chip 2
+#
+chip    2
+data_a  0x302
+ctrl_a  0x306
+data_b  0x303
+ctrl_b  0x307
+board   BAYCOM
+
+An example for a PA0HZP card:
+-----------------------------
+
+chip 1
+data_a 0x153
+data_b 0x151
+ctrl_a 0x152
+ctrl_b 0x150
+irq 9
+pclock 4915200
+board PA0HZP
+vector 0x168
+escc no
+#
+#
+#
+chip 2
+data_a 0x157
+data_b 0x155
+ctrl_a 0x156
+ctrl_b 0x154
+irq 9
+pclock 4915200
+board PA0HZP
+vector 0x168
+escc no
+
+A DRSI would should probably work with this:
+--------------------------------------------
+(actually: two DRSI cards...)
+
+chip 1
+data_a 0x303
+data_b 0x301
+ctrl_a 0x302
+ctrl_b 0x300
+irq 7
+pclock 4915200
+board DRSI
+escc no
+#
+#
+#
+chip 2
+data_a 0x313
+data_b 0x311
+ctrl_a 0x312
+ctrl_b 0x310
+irq 7
+pclock 4915200
+board DRSI
+escc no
+
+Note that you cannot use the on-board baudrate generator off DRSI
+cards. Use "mode dpll" for clock source (see below).
+
+This is based on information provided by Mike Bilow (and verified
+by Paul Helay)
+
+The utility "gencfg"
+--------------------
+
+If you only know the parameters for the PE1CHL driver for DOS,
+run gencfg. It will generate the correct port addresses (I hope).
+Its parameters are exactly the same as the ones you use with
+the "attach scc" command in net, except that the string "init" must 
+not appear. Example:
+
+gencfg 2 0x150 4 2 0 1 0x168 9 4915200 
+
+will print a skeleton z8530drv.conf for the OptoSCC to stdout.
+
+gencfg 2 0x300 2 4 5 -4 0 7 4915200 0x10
+
+does the same for the BAYCOM USCC card. In my opinion it is much easier
+to edit scc_config.h... 
+
+
+1.2.2 channel configuration
+===========================
+
+The channel definition is divided into three sub sections for each
+channel:
+
+An example for scc0:
+
+# DEVICE
+
+device scc0	# the device for the following params
+
+# MODEM / BUFFERS
+
+speed 1200		# the default baudrate
+clock dpll		# clock source: 
+			# 	dpll     = normal half duplex operation
+			# 	external = MODEM provides own Rx/Tx clock
+			#	divider  = use full duplex divider if
+			#		   installed (1)
+mode nrzi		# HDLC encoding mode
+			#	nrzi = 1k2 MODEM, G3RUH 9k6 MODEM
+			#	nrz  = DF9IC 9k6 MODEM
+			#
+bufsize	384		# size of buffers. Note that this must include
+			# the AX.25 header, not only the data field!
+			# (optional, defaults to 384)
+
+# KISS (Layer 1)
+
+txdelay 36              # (see chapter 1.4)
+persist 64
+slot    8
+tail    8
+fulldup 0
+wait    12
+min     3
+maxkey  7
+idle    3
+maxdef  120
+group   0
+txoff   off
+softdcd on                   
+slip    off
+
+The order WITHIN these sections is unimportant. The order OF these
+sections IS important. The MODEM parameters are set with the first
+recognized KISS parameter...
+
+Please note that you can initialize the board only once after boot
+(or insmod). You can change all parameters but "mode" and "clock" 
+later with the Sccparam program or through KISS. Just to avoid 
+security holes... 
+
+(1) this divider is usually mounted on the SCC-PBC (PA0HZP) or not
+    present at all (BayCom). It feeds back the output of the DPLL 
+    (digital pll) as transmit clock. Using this mode without a divider 
+    installed will normally result in keying the transceiver until 
+    maxkey expires --- of course without sending anything (useful).
+
+2. Attachment of a channel by your AX.25 software
+=================================================
+
+2.1 Kernel AX.25
+================
+
+To set up an AX.25 device you can simply type:
+
+	ifconfig scc0 44.128.1.1 hw ax25 dl0tha-7
+
+This will create a network interface with the IP number 44.128.20.107 
+and the callsign "dl0tha". If you do not have any IP number (yet) you 
+can use any of the 44.128.0.0 network. Note that you do not need 
+axattach. The purpose of axattach (like slattach) is to create a KISS 
+network device linked to a TTY. Please read the documentation of the 
+ax25-utils and the AX.25-HOWTO to learn how to set the parameters of
+the kernel AX.25.
+
+2.2 NOS, NET and TFKISS
+=======================
+
+Since the TTY driver (aka KISS TNC emulation) is gone you need
+to emulate the old behaviour. The cost of using these programs is
+that you probably need to compile the kernel AX.25, regardless of whether
+you actually use it or not. First setup your /etc/ax25/axports,
+for example:
+
+	9k6	dl0tha-9  9600  255 4 9600 baud port (scc3)
+	axlink	dl0tha-15 38400 255 4 Link to NOS
+
+Now "ifconfig" the scc device:
+
+	ifconfig scc3 44.128.1.1 hw ax25 dl0tha-9
+
+You can now axattach a pseudo-TTY:
+
+	axattach /dev/ptys0 axlink
+
+and start your NOS and attach /dev/ptys0 there. The problem is that
+NOS is reachable only via digipeating through the kernel AX.25
+(disastrous on a DAMA controlled channel). To solve this problem,
+configure "rxecho" to echo the incoming frames from "9k6" to "axlink"
+and outgoing frames from "axlink" to "9k6" and start:
+
+	rxecho
+
+Or simply use "kissbridge" coming with z8530drv-utils:
+
+	ifconfig scc3 hw ax25 dl0tha-9
+	kissbridge scc3 /dev/ptys0
+
+
+3. Adjustment and Display of parameters
+=======================================
+
+3.1 Displaying SCC Parameters:
+==============================
+
+Once a SCC channel has been attached, the parameter settings and 
+some statistic information can be shown using the param program:
+
+dl1bke-u:~$ sccstat scc0
+
+Parameters:
+
+speed       : 1200 baud
+txdelay     : 36
+persist     : 255
+slottime    : 0
+txtail      : 8
+fulldup     : 1
+waittime    : 12
+mintime     : 3 sec
+maxkeyup    : 7 sec
+idletime    : 3 sec
+maxdefer    : 120 sec
+group       : 0x00
+txoff       : off
+softdcd     : on
+SLIP        : off
+
+Status:
+
+HDLC                  Z8530           Interrupts         Buffers
+-----------------------------------------------------------------------
+Sent       :     273  RxOver :     0  RxInts :   125074  Size    :  384
+Received   :    1095  TxUnder:     0  TxInts :     4684  NoSpace :    0
+RxErrors   :    1591                  ExInts :    11776
+TxErrors   :       0                  SpInts :     1503
+Tx State   :    idle
+
+
+The status info shown is:
+
+Sent		- number of frames transmitted
+Received	- number of frames received
+RxErrors	- number of receive errors (CRC, ABORT)
+TxErrors	- number of discarded Tx frames (due to various reasons) 
+Tx State	- status of the Tx interrupt handler: idle/busy/active/tail (2)
+RxOver		- number of receiver overruns
+TxUnder		- number of transmitter underruns
+RxInts		- number of receiver interrupts
+TxInts		- number of transmitter interrupts
+EpInts		- number of receiver special condition interrupts
+SpInts		- number of external/status interrupts
+Size		- maximum size of an AX.25 frame (*with* AX.25 headers!)
+NoSpace		- number of times a buffer could not get allocated
+
+An overrun is abnormal. If lots of these occur, the product of
+baudrate and number of interfaces is too high for the processing
+power of your computer. NoSpace errors are unlikely to be caused by the
+driver or the kernel AX.25.
+
+
+3.2 Setting Parameters
+======================
+
+
+The setting of parameters of the emulated KISS TNC is done in the 
+same way in the SCC driver. You can change parameters by using
+the kissparms program from the ax25-utils package or use the program 
+"sccparam":
+
+     sccparam <device> <paramname> <decimal-|hexadecimal value>
+
+You can change the following parameters:
+
+param	    : value
+------------------------
+speed       : 1200
+txdelay     : 36
+persist     : 255
+slottime    : 0
+txtail      : 8
+fulldup     : 1
+waittime    : 12
+mintime     : 3
+maxkeyup    : 7
+idletime    : 3
+maxdefer    : 120
+group       : 0x00
+txoff       : off
+softdcd     : on
+SLIP        : off
+
+
+The parameters have the following meaning:
+
+speed:
+     The baudrate on this channel in bits/sec
+
+     Example: sccparam /dev/scc3 speed 9600
+
+txdelay:
+     The delay (in units of 10 ms) after keying of the 
+     transmitter, until the first byte is sent. This is usually 
+     called "TXDELAY" in a TNC.  When 0 is specified, the driver 
+     will just wait until the CTS signal is asserted. This 
+     assumes the presence of a timer or other circuitry in the 
+     MODEM and/or transmitter, that asserts CTS when the 
+     transmitter is ready for data.
+     A normal value of this parameter is 30-36.
+
+     Example: sccparam /dev/scc0 txd 20
+
+persist:
+     This is the probability that the transmitter will be keyed 
+     when the channel is found to be free.  It is a value from 0 
+     to 255, and the probability is (value+1)/256.  The value 
+     should be somewhere near 50-60, and should be lowered when 
+     the channel is used more heavily.
+
+     Example: sccparam /dev/scc2 persist 20
+
+slottime:
+     This is the time between samples of the channel. It is 
+     expressed in units of 10 ms.  About 200-300 ms (value 20-30) 
+     seems to be a good value.
+
+     Example: sccparam /dev/scc0 slot 20
+
+tail:
+     The time the transmitter will remain keyed after the last 
+     byte of a packet has been transferred to the SCC. This is 
+     necessary because the CRC and a flag still have to leave the 
+     SCC before the transmitter is keyed down. The value depends 
+     on the baudrate selected.  A few character times should be 
+     sufficient, e.g. 40ms at 1200 baud. (value 4)
+     The value of this parameter is in 10 ms units.
+
+     Example: sccparam /dev/scc2 4
+
+full:
+     The full-duplex mode switch. This can be one of the following 
+     values:
+
+     0:   The interface will operate in CSMA mode (the normal 
+          half-duplex packet radio operation)
+     1:   Fullduplex mode, i.e. the transmitter will be keyed at 
+          any time, without checking the received carrier.  It 
+          will be unkeyed when there are no packets to be sent.
+     2:   Like 1, but the transmitter will remain keyed, also 
+          when there are no packets to be sent.  Flags will be 
+          sent in that case, until a timeout (parameter 10) 
+          occurs.
+
+     Example: sccparam /dev/scc0 fulldup off
+
+wait:
+     The initial waittime before any transmit attempt, after the 
+     frame has been queue for transmit.  This is the length of 
+     the first slot in CSMA mode.  In full duplex modes it is
+     set to 0 for maximum performance.
+     The value of this parameter is in 10 ms units. 
+
+     Example: sccparam /dev/scc1 wait 4
+
+maxkey:
+     The maximal time the transmitter will be keyed to send 
+     packets, in seconds.  This can be useful on busy CSMA 
+     channels, to avoid "getting a bad reputation" when you are 
+     generating a lot of traffic.  After the specified time has 
+     elapsed, no new frame will be started. Instead, the trans-
+     mitter will be switched off for a specified time (parameter 
+     min), and then the selected algorithm for keyup will be 
+     started again.
+     The value 0 as well as "off" will disable this feature, 
+     and allow infinite transmission time. 
+
+     Example: sccparam /dev/scc0 maxk 20
+
+min:
+     This is the time the transmitter will be switched off when 
+     the maximum transmission time is exceeded.
+
+     Example: sccparam /dev/scc3 min 10
+
+idle
+     This parameter specifies the maximum idle time in full duplex 
+     2 mode, in seconds.  When no frames have been sent for this 
+     time, the transmitter will be keyed down.  A value of 0 is
+     has same result as the fullduplex mode 1. This parameter
+     can be disabled.
+
+     Example: sccparam /dev/scc2 idle off	# transmit forever
+
+maxdefer
+     This is the maximum time (in seconds) to wait for a free channel
+     to send. When this timer expires the transmitter will be keyed 
+     IMMEDIATELY. If you love to get trouble with other users you
+     should set this to a very low value ;-)
+
+     Example: sccparam /dev/scc0 maxdefer 240	# 2 minutes
+
+
+txoff:
+     When this parameter has the value 0, the transmission of packets
+     is enable. Otherwise it is disabled.
+
+     Example: sccparam /dev/scc2 txoff on
+
+group:
+     It is possible to build special radio equipment to use more than 
+     one frequency on the same band, e.g. using several receivers and 
+     only one transmitter that can be switched between frequencies.
+     Also, you can connect several radios that are active on the same 
+     band.  In these cases, it is not possible, or not a good idea, to 
+     transmit on more than one frequency.  The SCC driver provides a 
+     method to lock transmitters on different interfaces, using the 
+     "param <interface> group <x>" command.  This will only work when 
+     you are using CSMA mode (parameter full = 0).
+     The number <x> must be 0 if you want no group restrictions, and 
+     can be computed as follows to create restricted groups:
+     <x> is the sum of some OCTAL numbers:
+
+     200  This transmitter will only be keyed when all other 
+          transmitters in the group are off.
+     100  This transmitter will only be keyed when the carrier 
+          detect of all other interfaces in the group is off.
+     0xx  A byte that can be used to define different groups.  
+          Interfaces are in the same group, when the logical AND 
+          between their xx values is nonzero.
+
+     Examples:
+     When 2 interfaces use group 201, their transmitters will never be 
+     keyed at the same time.
+     When 2 interfaces use group 101, the transmitters will only key 
+     when both channels are clear at the same time.  When group 301, 
+     the transmitters will not be keyed at the same time.
+
+     Don't forget to convert the octal numbers into decimal before
+     you set the parameter.
+
+     Example: (to be written)
+
+softdcd:
+     use a software dcd instead of the real one... Useful for a very
+     slow squelch.
+
+     Example: sccparam /dev/scc0 soft on
+
+
+4. Problems 
+===========
+
+If you have tx-problems with your BayCom USCC card please check
+the manufacturer of the 8530. SGS chips have a slightly
+different timing. Try Zilog...  A solution is to write to register 8 
+instead to the data port, but this won't work with the ESCC chips. 
+*SIGH!*
+
+A very common problem is that the PTT locks until the maxkeyup timer
+expires, although interrupts and clock source are correct. In most
+cases compiling the driver with CONFIG_SCC_DELAY (set with
+make config) solves the problems. For more hints read the (pseudo) FAQ 
+and the documentation coming with z8530drv-utils.
+
+I got reports that the driver has problems on some 386-based systems.
+(i.e. Amstrad) Those systems have a bogus AT bus timing which will
+lead to delayed answers on interrupts. You can recognize these
+problems by looking at the output of Sccstat for the suspected
+port. If it shows under- and overruns you own such a system.
+
+Delayed processing of received data: This depends on
+
+- the kernel version
+
+- kernel profiling compiled or not
+
+- a high interrupt load
+
+- a high load of the machine --- running X, Xmorph, XV and Povray,
+  while compiling the kernel... hmm ... even with 32 MB RAM ...  ;-)
+  Or running a named for the whole .ampr.org domain on an 8 MB
+  box...
+
+- using information from rxecho or kissbridge.
+
+Kernel panics: please read /linux/README and find out if it
+really occurred within the scc driver.
+
+If you cannot solve a problem, send me
+
+- a description of the problem,
+- information on your hardware (computer system, scc board, modem)
+- your kernel version
+- the output of cat /proc/net/z8530
+
+4. Thor RLC100
+==============
+
+Mysteriously this board seems not to work with the driver. Anyone
+got it up-and-running?
+
+
+Many thanks to Linus Torvalds and Alan Cox for including the driver
+in the Linux standard distribution and their support.
+
+Joerg Reuter	ampr-net: dl1bke@db0pra.ampr.org
+		AX-25   : DL1BKE @ DB0ABH.#BAY.DEU.EU
+		Internet: jreuter@yaina.de
+		WWW     : http://yaina.de/jreuter