diff options
| author | Grant Likely <grant.likely@secretlab.ca> | 2011-01-26 10:10:40 -0700 |
|---|---|---|
| committer | Grant Likely <grant.likely@secretlab.ca> | 2011-01-31 00:09:01 -0700 |
| commit | d524dac9279b6a41ffdf7ff7958c577f2e387db6 (patch) | |
| tree | 294166d18a1c89c4cebb2571ea7b124876fb01ef /Documentation/powerpc/dts-bindings/fsl | |
| parent | 1bae4ce27c9c90344f23c65ea6966c50ffeae2f5 (diff) | |
dt: Move device tree documentation out of powerpc directory
The device tree is used by more than just PowerPC. Make the documentation
directory available to all.
v2: reorganized files while moving to create arch and driver specific
directories.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Diffstat (limited to 'Documentation/powerpc/dts-bindings/fsl')
39 files changed, 0 insertions, 2145 deletions
diff --git a/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt b/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt deleted file mode 100644 index 35a46536240..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/83xx-512x-pci.txt +++ /dev/null @@ -1,40 +0,0 @@ -* Freescale 83xx and 512x PCI bridges - -Freescale 83xx and 512x SOCs include the same pci bridge core. - -83xx/512x specific notes: -- reg: should contain two address length tuples - The first is for the internal pci bridge registers - The second is for the pci config space access registers - -Example (MPC8313ERDB) - pci0: pci@e0008500 { - cell-index = <1>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = < - /* IDSEL 0x0E -mini PCI */ - 0x7000 0x0 0x0 0x1 &ipic 18 0x8 - 0x7000 0x0 0x0 0x2 &ipic 18 0x8 - 0x7000 0x0 0x0 0x3 &ipic 18 0x8 - 0x7000 0x0 0x0 0x4 &ipic 18 0x8 - - /* IDSEL 0x0F - PCI slot */ - 0x7800 0x0 0x0 0x1 &ipic 17 0x8 - 0x7800 0x0 0x0 0x2 &ipic 18 0x8 - 0x7800 0x0 0x0 0x3 &ipic 17 0x8 - 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; - interrupt-parent = <&ipic>; - interrupts = <66 0x8>; - bus-range = <0x0 0x0>; - ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 - 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 - 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; - clock-frequency = <66666666>; - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - reg = <0xe0008500 0x100 /* internal registers */ - 0xe0008300 0x8>; /* config space access registers */ - compatible = "fsl,mpc8349-pci"; - device_type = "pci"; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt b/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt deleted file mode 100644 index b0019eb5330..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/8xxx_gpio.txt +++ /dev/null @@ -1,60 +0,0 @@ -GPIO controllers on MPC8xxx SoCs - -This is for the non-QE/CPM/GUTs GPIO controllers as found on -8349, 8572, 8610 and compatible. - -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. - -Required properties: -- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for - 83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx. -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). - - interrupts : Interrupt mapping for GPIO IRQ. - - interrupt-parent : Phandle for the interrupt controller that - services interrupts for this device. -- gpio-controller : Marks the port as GPIO controller. - -Example of gpio-controller nodes for a MPC8347 SoC: - - gpio1: gpio-controller@c00 { - #gpio-cells = <2>; - compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; - reg = <0xc00 0x100>; - interrupts = <74 0x8>; - interrupt-parent = <&ipic>; - gpio-controller; - }; - - gpio2: gpio-controller@d00 { - #gpio-cells = <2>; - compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; - reg = <0xd00 0x100>; - interrupts = <75 0x8>; - interrupt-parent = <&ipic>; - gpio-controller; - }; - -See booting-without-of.txt for details of how to specify GPIO -information for devices. - -To use GPIO pins as interrupt sources for peripherals, specify the -GPIO controller as the interrupt parent and define GPIO number + -trigger mode using the interrupts property, which is defined like -this: - -interrupts = <number trigger>, where: - - number: GPIO pin (0..31) - - trigger: trigger mode: - 2 = trigger on falling edge - 3 = trigger on both edges - -Example of device using this is: - - funkyfpga@0 { - compatible = "funky-fpga"; - ... - interrupts = <4 3>; - interrupt-parent = <&gpio1>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt deleted file mode 100644 index 39e941515a3..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/board.txt +++ /dev/null @@ -1,63 +0,0 @@ -* Board Control and Status (BCSR) - -Required properties: - - - compatible : Should be "fsl,<board>-bcsr" - - reg : Offset and length of the register set for the device - -Example: - - bcsr@f8000000 { - compatible = "fsl,mpc8360mds-bcsr"; - reg = <f8000000 8000>; - }; - -* Freescale on board FPGA - -This is the memory-mapped registers for on board FPGA. - -Required properities: -- compatible : should be "fsl,fpga-pixis". -- reg : should contain the address and the length of the FPPGA register - set. -- interrupt-parent: should specify phandle for the interrupt controller. -- interrupts : should specify event (wakeup) IRQ. - -Example (MPC8610HPCD): - - board-control@e8000000 { - compatible = "fsl,fpga-pixis"; - reg = <0xe8000000 32>; - interrupt-parent = <&mpic>; - interrupts = <8 8>; - }; - -* Freescale BCSR GPIO banks - -Some BCSR registers act as simple GPIO controllers, each such -register can be represented by the gpio-controller node. - -Required properities: -- compatible : Should be "fsl,<board>-bcsr-gpio". -- reg : Should contain the address and the length of the GPIO bank - register. -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). -- gpio-controller : Marks the port as GPIO controller. - -Example: - - bcsr@1,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8360mds-bcsr"; - reg = <1 0 0x8000>; - ranges = <0 1 0 0x8000>; - - bcsr13: gpio-controller@d { - #gpio-cells = <2>; - compatible = "fsl,mpc8360mds-bcsr-gpio"; - reg = <0xd 1>; - gpio-controller; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/can.txt b/Documentation/powerpc/dts-bindings/fsl/can.txt deleted file mode 100644 index 2fa4fcd38fd..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/can.txt +++ /dev/null @@ -1,53 +0,0 @@ -CAN Device Tree Bindings ------------------------- - -(c) 2006-2009 Secret Lab Technologies Ltd -Grant Likely <grant.likely@secretlab.ca> - -fsl,mpc5200-mscan nodes ------------------------ -In addition to the required compatible-, reg- and interrupt-properties, you can -also specify which clock source shall be used for the controller: - -- fsl,mscan-clock-source : a string describing the clock source. Valid values - are: "ip" for ip bus clock - "ref" for reference clock (XTAL) - "ref" is default in case this property is not - present. - -fsl,mpc5121-mscan nodes ------------------------ -In addition to the required compatible-, reg- and interrupt-properties, you can -also specify which clock source and divider shall be used for the controller: - -- fsl,mscan-clock-source : a string describing the clock source. Valid values - are: "ip" for ip bus clock - "ref" for reference clock - "sys" for system clock - If this property is not present, an optimal CAN - clock source and frequency based on the system - clock will be selected. If this is not possible, - the reference clock will be used. - -- fsl,mscan-clock-divider: for the reference and system clock, an additional - clock divider can be specified. By default, a - value of 1 is used. - -Note that the MPC5121 Rev. 1 processor is not supported. - -Examples: - can@1300 { - compatible = "fsl,mpc5121-mscan"; - interrupts = <12 0x8>; - interrupt-parent = <&ipic>; - reg = <0x1300 0x80>; - }; - - can@1380 { - compatible = "fsl,mpc5121-mscan"; - interrupts = <13 0x8>; - interrupt-parent = <&ipic>; - reg = <0x1380 0x80>; - fsl,mscan-clock-source = "ref"; - fsl,mscan-clock-divider = <3>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt deleted file mode 100644 index 160c752484b..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt +++ /dev/null @@ -1,67 +0,0 @@ -* Freescale Communications Processor Module - -NOTE: This is an interim binding, and will likely change slightly, -as more devices are supported. The QE bindings especially are -incomplete. - -* Root CPM node - -Properties: -- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe". -- reg : A 48-byte region beginning with CPCR. - -Example: - cpm@119c0 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - compatible = "fsl,mpc8272-cpm", "fsl,cpm2"; - reg = <119c0 30>; - } - -* Properties common to multiple CPM/QE devices - -- fsl,cpm-command : This value is ORed with the opcode and command flag - to specify the device on which a CPM command operates. - -- fsl,cpm-brg : Indicates which baud rate generator the device - is associated with. If absent, an unused BRG - should be dynamically allocated. If zero, the - device uses an external clock rather than a BRG. - -- reg : Unless otherwise specified, the first resource represents the - scc/fcc/ucc registers, and the second represents the device's - parameter RAM region (if it has one). - -* Multi-User RAM (MURAM) - -The multi-user/dual-ported RAM is expressed as a bus under the CPM node. - -Ranges must be set up subject to the following restrictions: - -- Children's reg nodes must be offsets from the start of all muram, even - if the user-data area does not begin at zero. -- If multiple range entries are used, the difference between the parent - address and the child address must be the same in all, so that a single - mapping can cover them all while maintaining the ability to determine - CPM-side offsets with pointer subtraction. It is recommended that - multiple range entries not be used. -- A child address of zero must be translatable, even if no reg resources - contain it. - -A child "data" node must exist, compatible with "fsl,cpm-muram-data", to -indicate the portion of muram that is usable by the OS for arbitrary -purposes. The data node may have an arbitrary number of reg resources, -all of which contribute to the allocatable muram pool. - -Example, based on mpc8272: - muram@0 { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 10000>; - - data@0 { - compatible = "fsl,cpm-muram-data"; - reg = <0 2000 9800 800>; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt deleted file mode 100644 index 4c7d45eaf02..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt +++ /dev/null @@ -1,21 +0,0 @@ -* Baud Rate Generators - -Currently defined compatibles: -fsl,cpm-brg -fsl,cpm1-brg -fsl,cpm2-brg - -Properties: -- reg : There may be an arbitrary number of reg resources; BRG - numbers are assigned to these in order. -- clock-frequency : Specifies the base frequency driving - the BRG. - -Example: - brg@119f0 { - compatible = "fsl,mpc8272-brg", - "fsl,cpm2-brg", - "fsl,cpm-brg"; - reg = <119f0 10 115f0 10>; - clock-frequency = <d#25000000>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt deleted file mode 100644 index 87bc6048667..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt +++ /dev/null @@ -1,41 +0,0 @@ -* I2C - -The I2C controller is expressed as a bus under the CPM node. - -Properties: -- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c" -- reg : On CPM2 devices, the second resource doesn't specify the I2C - Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM - (typically 0x8afc 0x2). -- #address-cells : Should be one. The cell is the i2c device address with - the r/w bit set to zero. -- #size-cells : Should be zero. -- clock-frequency : Can be used to set the i2c clock frequency. If - unspecified, a default frequency of 60kHz is being used. -The following two properties are deprecated. They are only used by legacy -i2c drivers to find the bus to probe: -- linux,i2c-index : Can be used to hard code an i2c bus number. By default, - the bus number is dynamically assigned by the i2c core. -- linux,i2c-class : Can be used to override the i2c class. The class is used - by legacy i2c device drivers to find a bus in a specific context like - system management, video or sound. By default, I2C_CLASS_HWMON (1) is - being used. The definition of the classes can be found in - include/i2c/i2c.h - -Example, based on mpc823: - - i2c@860 { - compatible = "fsl,mpc823-i2c", - "fsl,cpm1-i2c"; - reg = <0x860 0x20 0x3c80 0x30>; - interrupts = <16>; - interrupt-parent = <&CPM_PIC>; - fsl,cpm-command = <0x10>; - #address-cells = <1>; - #size-cells = <0>; - - rtc@68 { - compatible = "dallas,ds1307"; - reg = <0x68>; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt deleted file mode 100644 index 8e3ee168161..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt +++ /dev/null @@ -1,18 +0,0 @@ -* Interrupt Controllers - -Currently defined compatibles: -- fsl,cpm1-pic - - only one interrupt cell -- fsl,pq1-pic -- fsl,cpm2-pic - - second interrupt cell is level/sense: - - 2 is falling edge - - 8 is active low - -Example: - interrupt-controller@10c00 { - #interrupt-cells = <2>; - interrupt-controller; - reg = <10c00 80>; - compatible = "mpc8272-pic", "fsl,cpm2-pic"; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt deleted file mode 100644 index 74bfda4bb82..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt +++ /dev/null @@ -1,15 +0,0 @@ -* USB (Universal Serial Bus Controller) - -Properties: -- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb" - -Example: - usb@11bc0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,cpm2-usb"; - reg = <11b60 18 8b00 100>; - interrupts = <b 8>; - interrupt-parent = <&PIC>; - fsl,cpm-command = <2e600000>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/gpio.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/gpio.txt deleted file mode 100644 index 349f79fd707..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/gpio.txt +++ /dev/null @@ -1,38 +0,0 @@ -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. - -On CPM1 devices, all ports are using slightly different register layouts. -Ports A, C and D are 16bit ports and Ports B and E are 32bit ports. - -On CPM2 devices, all ports are 32bit ports and use a common register layout. - -Required properties: -- compatible : "fsl,cpm1-pario-bank-a", "fsl,cpm1-pario-bank-b", - "fsl,cpm1-pario-bank-c", "fsl,cpm1-pario-bank-d", - "fsl,cpm1-pario-bank-e", "fsl,cpm2-pario-bank" -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). -- gpio-controller : Marks the port as GPIO controller. - -Example of three SOC GPIO banks defined as gpio-controller nodes: - - CPM1_PIO_A: gpio-controller@950 { - #gpio-cells = <2>; - compatible = "fsl,cpm1-pario-bank-a"; - reg = <0x950 0x10>; - gpio-controller; - }; - - CPM1_PIO_B: gpio-controller@ab8 { - #gpio-cells = <2>; - compatible = "fsl,cpm1-pario-bank-b"; - reg = <0xab8 0x10>; - gpio-controller; - }; - - CPM1_PIO_E: gpio-controller@ac8 { - #gpio-cells = <2>; - compatible = "fsl,cpm1-pario-bank-e"; - reg = <0xac8 0x18>; - gpio-controller; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt deleted file mode 100644 index 0e426944658..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt +++ /dev/null @@ -1,45 +0,0 @@ -* Network - -Currently defined compatibles: -- fsl,cpm1-scc-enet -- fsl,cpm2-scc-enet -- fsl,cpm1-fec-enet -- fsl,cpm2-fcc-enet (third resource is GFEMR) -- fsl,qe-enet - -Example: - - ethernet@11300 { - device_type = "network"; - compatible = "fsl,mpc8272-fcc-enet", - "fsl,cpm2-fcc-enet"; - reg = <11300 20 8400 100 11390 1>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <20 8>; - interrupt-parent = <&PIC>; - phy-handle = <&PHY0>; - fsl,cpm-command = <12000300>; - }; - -* MDIO - -Currently defined compatibles: -fsl,pq1-fec-mdio (reg is same as first resource of FEC device) -fsl,cpm2-mdio-bitbang (reg is port C registers) - -Properties for fsl,cpm2-mdio-bitbang: -fsl,mdio-pin : pin of port C controlling mdio data -fsl,mdc-pin : pin of port C controlling mdio clock - -Example: - mdio@10d40 { - device_type = "mdio"; - compatible = "fsl,mpc8272ads-mdio-bitbang", - "fsl,mpc8272-mdio-bitbang", - "fsl,cpm2-mdio-bitbang"; - reg = <10d40 14>; - #address-cells = <1>; - #size-cells = <0>; - fsl,mdio-pin = <12>; - fsl,mdc-pin = <13>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt deleted file mode 100644 index 4f8930263dd..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt +++ /dev/null @@ -1,115 +0,0 @@ -* Freescale QUICC Engine module (QE) -This represents qe module that is installed on PowerQUICC II Pro. - -NOTE: This is an interim binding; it should be updated to fit -in with the CPM binding later in this document. - -Basically, it is a bus of devices, that could act more or less -as a complete entity (UCC, USB etc ). All of them should be siblings on -the "root" qe node, using the common properties from there. -The description below applies to the qe of MPC8360 and -more nodes and properties would be extended in the future. - -i) Root QE device - -Required properties: -- compatible : should be "fsl,qe"; -- model : precise model of the QE, Can be "QE", "CPM", or "CPM2" -- reg : offset and length of the device registers. -- bus-frequency : the clock frequency for QUICC Engine. -- fsl,qe-num-riscs: define how many RISC engines the QE has. -- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the - threads. - -Optional properties: -- fsl,firmware-phandle: - Usage: required only if there is no fsl,qe-firmware child node - Value type: <phandle> - Definition: Points to a firmware node (see "QE Firmware Node" below) - that contains the firmware that should be uploaded for this QE. - The compatible property for the firmware node should say, - "fsl,qe-firmware". - -Recommended properties -- brg-frequency : the internal clock source frequency for baud-rate - generators in Hz. - -Example: - qe@e0100000 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - compatible = "fsl,qe"; - ranges = <0 e0100000 00100000>; - reg = <e0100000 480>; - brg-frequency = <0>; - bus-frequency = <179A7B00>; - } - -* Multi-User RAM (MURAM) - -Required properties: -- compatible : should be "fsl,qe-muram", "fsl,cpm-muram". -- mode : the could be "host" or "slave". -- ranges : Should be defined as specified in 1) to describe the - translation of MURAM addresses. -- data-only : sub-node which defines the address area under MURAM - bus that can be allocated as data/parameter - -Example: - - muram@10000 { - compatible = "fsl,qe-muram", "fsl,cpm-muram"; - ranges = <0 00010000 0000c000>; - - data-only@0{ - compatible = "fsl,qe-muram-data", - "fsl,cpm-muram-data"; - reg = <0 c000>; - }; - }; - -* QE Firmware Node - -This node defines a firmware binary that is embedded in the device tree, for -the purpose of passing the firmware from bootloader to the kernel, or from -the hypervisor to the guest. - -The firmware node itself contains the firmware binary contents, a compatible -property, and any firmware-specific properties. The node should be placed -inside a QE node that needs it. Doing so eliminates the need for a -fsl,firmware-phandle property. Other QE nodes that need the same firmware -should define an fsl,firmware-phandle property that points to the firmware node -in the first QE node. - -The fsl,firmware property can be specified in the DTS (possibly using incbin) -or can be inserted by the boot loader at boot time. - -Required properties: - - compatible - Usage: required - Value type: <string> - Definition: A standard property. Specify a string that indicates what - kind of firmware it is. For QE, this should be "fsl,qe-firmware". - - - fsl,firmware - Usage: required - Value type: <prop-encoded-array>, encoded as an array of bytes - Definition: A standard property. This property contains the firmware - binary "blob". - -Example: - qe1@e0080000 { - compatible = "fsl,qe"; - qe_firmware:qe-firmware { - compatible = "fsl,qe-firmware"; - fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...]; - }; - ... - }; - - qe2@e0090000 { - compatible = "fsl,qe"; - fsl,firmware-phandle = <&qe_firmware>; - ... - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt deleted file mode 100644 index 249db3a15d1..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt +++ /dev/null @@ -1,24 +0,0 @@ -* Uploaded QE firmware - - If a new firmware has been uploaded to the QE (usually by the - boot loader), then a 'firmware' child node should be added to the QE - node. This node provides information on the uploaded firmware that - device drivers may need. - - Required properties: - - id: The string name of the firmware. This is taken from the 'id' - member of the qe_firmware structure of the uploaded firmware. - Device drivers can search this string to determine if the - firmware they want is already present. - - extended-modes: The Extended Modes bitfield, taken from the - firmware binary. It is a 64-bit number represented - as an array of two 32-bit numbers. - - virtual-traps: The virtual traps, taken from the firmware binary. - It is an array of 8 32-bit numbers. - -Example: - firmware { - id = "Soft-UART"; - extended-modes = <0 0>; - virtual-traps = <0 0 0 0 0 0 0 0>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt deleted file mode 100644 index 60984260207..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt +++ /dev/null @@ -1,51 +0,0 @@ -* Parallel I/O Ports - -This node configures Parallel I/O ports for CPUs with QE support. -The node should reside in the "soc" node of the tree. For each -device that using parallel I/O ports, a child node should be created. -See the definition of the Pin configuration nodes below for more -information. - -Required properties: -- device_type : should be "par_io". -- reg : offset to the register set and its length. -- num-ports : number of Parallel I/O ports - -Example: -par_io@1400 { - reg = <1400 100>; - #address-cells = <1>; - #size-cells = <0>; - device_type = "par_io"; - num-ports = <7>; - ucc_pin@01 { - ...... - }; - -Note that "par_io" nodes are obsolete, and should not be used for -the new device trees. Instead, each Par I/O bank should be represented -via its own gpio-controller node: - -Required properties: -- #gpio-cells : should be "2". -- compatible : should be "fsl,<chip>-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank". -- reg : offset to the register set and its length. -- gpio-controller : node to identify gpio controllers. - -Example: - qe_pio_a: gpio-controller@1400 { - #gpio-cells = <2>; - compatible = "fsl,mpc8360-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank"; - reg = <0x1400 0x18>; - gpio-controller; - }; - - qe_pio_e: gpio-controller@1460 { - #gpio-cells = <2>; - compatible = "fsl,mpc8360-qe-pario-bank", - "fsl,mpc8323-qe-pario-bank"; - reg = <0x1460 0x18>; - gpio-controller; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt deleted file mode 100644 index c5b43061db3..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt +++ /dev/null @@ -1,60 +0,0 @@ -* Pin configuration nodes - -Required properties: -- linux,phandle : phandle of this node; likely referenced by a QE - device. -- pio-map : array of pin configurations. Each pin is defined by 6 - integers. The six numbers are respectively: port, pin, dir, - open_drain, assignment, has_irq. - - port : port number of the pin; 0-6 represent port A-G in UM. - - pin : pin number in the port. - - dir : direction of the pin, should encode as follows: - - 0 = The pin is disabled - 1 = The pin is an output - 2 = The pin is an input - 3 = The pin is I/O - - - open_drain : indicates the pin is normal or wired-OR: - - 0 = The pin is actively driven as an output - 1 = The pin is an open-drain driver. As an output, the pin is - driven active-low, otherwise it is three-stated. - - - assignment : function number of the pin according to the Pin Assignment - tables in User Manual. Each pin can have up to 4 possible functions in - QE and two options for CPM. - - has_irq : indicates if the pin is used as source of external - interrupts. - -Example: - ucc_pin@01 { - linux,phandle = <140001>; - pio-map = < - /* port pin dir open_drain assignment has_irq */ - 0 3 1 0 1 0 /* TxD0 */ - 0 4 1 0 1 0 /* TxD1 */ - 0 5 1 0 1 0 /* TxD2 */ - 0 6 1 0 1 0 /* TxD3 */ - 1 6 1 0 3 0 /* TxD4 */ - 1 7 1 0 1 0 /* TxD5 */ - 1 9 1 0 2 0 /* TxD6 */ - 1 a 1 0 2 0 /* TxD7 */ - 0 9 2 0 1 0 /* RxD0 */ - 0 a 2 0 1 0 /* RxD1 */ - 0 b 2 0 1 0 /* RxD2 */ - 0 c 2 0 1 0 /* RxD3 */ - 0 d 2 0 1 0 /* RxD4 */ - 1 1 2 0 2 0 /* RxD5 */ - 1 0 2 0 2 0 /* RxD6 */ - 1 4 2 0 2 0 /* RxD7 */ - 0 7 1 0 1 0 /* TX_EN */ - 0 8 1 0 1 0 /* TX_ER */ - 0 f 2 0 1 0 /* RX_DV */ - 0 10 2 0 1 0 /* RX_ER */ - 0 0 2 0 1 0 /* RX_CLK */ - 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ - 2 8 2 0 1 0>; /* GTX125 - CLK9 */ - }; - - diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt deleted file mode 100644 index e47734bee3f..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt +++ /dev/null @@ -1,70 +0,0 @@ -* UCC (Unified Communications Controllers) - -Required properties: -- device_type : should be "network", "hldc", "uart", "transparent" - "bisync", "atm", or "serial". -- compatible : could be "ucc_geth" or "fsl_atm" and so on. -- cell-index : the ucc number(1-8), corresponding to UCCx in UM. -- reg : Offset and length of the register set for the device -- interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. -- pio-handle : The phandle for the Parallel I/O port configuration. -- port-number : for UART drivers, the port number to use, between 0 and 3. - This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0. - The port number is added to the minor number of the device. Unlike the - CPM UART driver, the port-number is required for the QE UART driver. -- soft-uart : for UART drivers, if specified this means the QE UART device - driver should use "Soft-UART" mode, which is needed on some SOCs that have - broken UART hardware. Soft-UART is provided via a microcode upload. -- rx-clock-name: the UCC receive clock source - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -- tx-clock-name: the UCC transmit clock source - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -The following two properties are deprecated. rx-clock has been replaced -with rx-clock-name, and tx-clock has been replaced with tx-clock-name. -Drivers that currently use the deprecated properties should continue to -do so, in order to support older device trees, but they should be updated -to check for the new properties first. -- rx-clock : represents the UCC receive clock source. - 0x00 : clock source is disabled; - 0x1~0x10 : clock source is BRG1~BRG16 respectively; - 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. -- tx-clock: represents the UCC transmit clock source; - 0x00 : clock source is disabled; - 0x1~0x10 : clock source is BRG1~BRG16 respectively; - 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. - -Required properties for network device_type: -- mac-address : list of bytes representing the ethernet address. -- phy-handle : The phandle for the PHY connected to this controller. - -Recommended properties: -- phy-connection-type : a string naming the controller/PHY interface type, - i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal - Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), - "tbi", or "rtbi". - -Example: - ucc@2000 { - device_type = "network"; - compatible = "ucc_geth"; - cell-index = <1>; - reg = <2000 200>; - interrupts = <a0 0>; - interrupt-parent = <700>; - mac-address = [ 00 04 9f 00 23 23 ]; - rx-clock = "none"; - tx-clock = "clk9"; - phy-handle = <212000>; - phy-connection-type = "gmii"; - pio-handle = <140001>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt deleted file mode 100644 index 9ccd5f30405..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt +++ /dev/null @@ -1,37 +0,0 @@ -Freescale QUICC Engine USB Controller - -Required properties: -- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb". -- reg : the first two cells should contain usb registers location and - length, the next two two cells should contain PRAM location and - length. -- interrupts : should contain USB interrupt. -- interrupt-parent : interrupt source phandle. -- fsl,fullspeed-clock : specifies the full speed USB clock source: - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -- fsl,lowspeed-clock : specifies the low speed USB clock source: - "none": clock source is disabled - "brg1" through "brg16": clock source is BRG1-BRG16, respectively - "clk1" through "clk24": clock source is CLK1-CLK24, respectively -- hub-power-budget : USB power budget for the root hub, in mA. -- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP, - USBRN, SPEED (optional), and POWER (optional). - -Example: - -usb@6c0 { - compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb"; - reg = <0x6c0 0x40 0x8b00 0x100>; - interrupts = <11>; - interrupt-parent = <&qeic>; - fsl,fullspeed-clock = "clk21"; - gpios = <&qe_pio_b 2 0 /* USBOE */ - &qe_pio_b 3 0 /* USBTP */ - &qe_pio_b 8 0 /* USBTN */ - &qe_pio_b 9 0 /* USBRP */ - &qe_pio_b 11 0 /* USBRN */ - &qe_pio_e 20 0 /* SPEED */ - &qe_pio_e 21 0 /* POWER */>; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt deleted file mode 100644 index 2ea76d9d137..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt +++ /dev/null @@ -1,32 +0,0 @@ -* Serial - -Currently defined compatibles: -- fsl,cpm1-smc-uart -- fsl,cpm2-smc-uart -- fsl,cpm1-scc-uart -- fsl,cpm2-scc-uart -- fsl,qe-uart - -Modem control lines connected to GPIO controllers are listed in the gpios -property as described in booting-without-of.txt, section IX.1 in the following -order: - -CTS, RTS, DCD, DSR, DTR, and RI. - -The gpios property is optional and can be left out when control lines are -not used. - -Example: - - serial@11a00 { - device_type = "serial"; - compatible = "fsl,mpc8272-scc-uart", - "fsl,cpm2-scc-uart"; - reg = <11a00 20 8000 100>; - interrupts = <28 8>; - interrupt-parent = <&PIC>; - fsl,cpm-brg = <1>; - fsl,cpm-command = <00800000>; - gpios = <&gpio_c 15 0 - &gpio_d 29 0>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/diu.txt b/Documentation/powerpc/dts-bindings/fsl/diu.txt deleted file mode 100644 index b66cb6d31d6..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/diu.txt +++ /dev/null @@ -1,34 +0,0 @@ -* Freescale Display Interface Unit - -The Freescale DIU is a LCD controller, with proper hardware, it can also -drive DVI monitors. - -Required properties: -- compatible : should be "fsl,diu" or "fsl,mpc5121-diu". -- reg : should contain at least address and length of the DIU register - set. -- interrupts : one DIU interrupt should be described here. -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Optional properties: -- edid : verbatim EDID data block describing attached display. - Data from the detailed timing descriptor will be used to - program the display controller. - -Example (MPC8610HPCD): - display@2c000 { - compatible = "fsl,diu"; - reg = <0x2c000 100>; - interrupts = <72 2>; - interrupt-parent = <&mpic>; - }; - -Example for MPC5121: - display@2100 { - compatible = "fsl,mpc5121-diu"; - reg = <0x2100 0x100>; - interrupts = <64 0x8>; - interrupt-parent = <&ipic>; - edid = [edid-data]; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/dma.txt b/Documentation/powerpc/dts-bindings/fsl/dma.txt deleted file mode 100644 index 2a4b4bce611..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/dma.txt +++ /dev/null @@ -1,144 +0,0 @@ -* Freescale 83xx DMA Controller - -Freescale PowerPC 83xx have on chip general purpose DMA controllers. - -Required properties: - -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8349, mpc8360, etc.) and the second is - "fsl,elo-dma" -- reg : <registers mapping for DMA general status reg> -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. -- cell-index : controller index. 0 for controller @ 0x8100 -- interrupts : <interrupt mapping for DMA IRQ> -- interrupt-parent : optional, if needed for interrupt mapping - - -- DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8349, mpc8350, etc.) and the second is - "fsl,elo-dma-channel". However, see note below. - - reg : <registers mapping for channel> - - cell-index : dma channel index starts at 0. - -Optional properties: - - interrupts : <interrupt mapping for DMA channel IRQ> - (on 83xx this is expected to be identical to - the interrupts property of the parent node) - - interrupt-parent : optional, if needed for interrupt mapping - -Example: - dma@82a8 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8349-dma", "fsl,elo-dma"; - reg = <0x82a8 4>; - ranges = <0 0x8100 0x1a4>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - cell-index = <0>; - dma-channel@0 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <0>; - reg = <0 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - dma-channel@80 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <1>; - reg = <0x80 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - dma-channel@100 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <2>; - reg = <0x100 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - dma-channel@180 { - compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel"; - cell-index = <3>; - reg = <0x180 0x80>; - interrupt-parent = <&ipic>; - interrupts = <71 8>; - }; - }; - -* Freescale 85xx/86xx DMA Controller - -Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. - -Required properties: - -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8540, mpc8540, etc.) and the second is - "fsl,eloplus-dma" -- reg : <registers mapping for DMA general status reg> -- cell-index : controller index. 0 for controller @ 0x21000, - 1 for controller @ 0xc000 -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. - -- DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8540, mpc8560, etc.) and the second is - "fsl,eloplus-dma-channel". However, see note below. - - cell-index : dma channel index starts at 0. - - reg : <registers mapping for channel> - - interrupts : <interrupt mapping for DMA channel IRQ> - - interrupt-parent : optional, if needed for interrupt mapping - -Example: - dma@21300 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma"; - reg = <0x21300 4>; - ranges = <0 0x21100 0x200>; - cell-index = <0>; - dma-channel@0 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0 0x80>; - cell-index = <0>; - interrupt-parent = <&mpic>; - interrupts = <20 2>; - }; - dma-channel@80 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0x80 0x80>; - cell-index = <1>; - interrupt-parent = <&mpic>; - interrupts = <21 2>; - }; - dma-channel@100 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0x100 0x80>; - cell-index = <2>; - interrupt-parent = <&mpic>; - interrupts = <22 2>; - }; - dma-channel@180 { - compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel"; - reg = <0x180 0x80>; - cell-index = <3>; - interrupt-parent = <&mpic>; - interrupts = <23 2>; - }; - }; - -Note on DMA channel compatible properties: The compatible property must say -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA -driver (fsldma). Any DMA channel used by fsldma cannot be used by another -DMA driver, such as the SSI sound drivers for the MPC8610. Therefore, any DMA -channel that should be used for another driver should not use -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel". For the SSI drivers, for -example, the compatible property should be "fsl,ssi-dma-channel". See ssi.txt -for more information. diff --git a/Documentation/powerpc/dts-bindings/fsl/esdhc.txt b/Documentation/powerpc/dts-bindings/fsl/esdhc.txt deleted file mode 100644 index 64bcb8be973..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/esdhc.txt +++ /dev/null @@ -1,29 +0,0 @@ -* Freescale Enhanced Secure Digital Host Controller (eSDHC) - -The Enhanced Secure Digital Host Controller provides an interface -for MMC, SD, and SDIO types of memory cards. - -Required properties: - - compatible : should be - "fsl,<chip>-esdhc", "fsl,esdhc" - - reg : should contain eSDHC registers location and length. - - interrupts : should contain eSDHC interrupt. - - interrupt-parent : interrupt source phandle. - - clock-frequency : specifies eSDHC base clock frequency. - - sdhci,wp-inverted : (optional) specifies that eSDHC controller - reports inverted write-protect state; - - sdhci,1-bit-only : (optional) specifies that a controller can - only handle 1-bit data transfers. - - sdhci,auto-cmd12: (optional) specifies that a controller can - only handle auto CMD12. - -Example: - -sdhci@2e000 { - compatible = "fsl,mpc8378-esdhc", "fsl,esdhc"; - reg = <0x2e000 0x1000>; - interrupts = <42 0x8>; - interrupt-parent = <&ipic>; - /* Filled in by U-Boot */ - clock-frequency = <0>; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/gtm.txt b/Documentation/powerpc/dts-bindings/fsl/gtm.txt deleted file mode 100644 index 9a33efded4b..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/gtm.txt +++ /dev/null @@ -1,31 +0,0 @@ -* Freescale General-purpose Timers Module - -Required properties: - - compatible : should be - "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs - "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs - "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs - - reg : should contain gtm registers location and length (0x40). - - interrupts : should contain four interrupts. - - interrupt-parent : interrupt source phandle. - - clock-frequency : specifies the frequency driving the timer. - -Example: - -timer@500 { - compatible = "fsl,mpc8360-gtm", "fsl,gtm"; - reg = <0x500 0x40>; - interrupts = <90 8 78 8 84 8 72 8>; - interrupt-parent = <&ipic>; - /* filled by u-boot */ - clock-frequency = <0>; -}; - -timer@440 { - compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm"; - reg = <0x440 0x40>; - interrupts = <12 13 14 15>; - interrupt-parent = <&qeic>; - /* filled by u-boot */ - clock-frequency = <0>; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/guts.txt b/Documentation/powerpc/dts-bindings/fsl/guts.txt deleted file mode 100644 index 9e7a2417dac..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/guts.txt +++ /dev/null @@ -1,25 +0,0 @@ -* Global Utilities Block - -The global utilities block controls power management, I/O device -enabling, power-on-reset configuration monitoring, general-purpose -I/O signal configuration, alternate function selection for multiplexed -signals, and clock control. - -Required properties: - - - compatible : Should define the compatible device type for - global-utilities. - - reg : Offset and length of the register set for the device. - -Recommended properties: - - - fsl,has-rstcr : Indicates that the global utilities register set - contains a functioning "reset control register" (i.e. the board - is wired to reset upon setting the HRESET_REQ bit in this register). - -Example: - global-utilities@e0000 { /* global utilities block */ - compatible = "fsl,mpc8548-guts"; - reg = <e0000 1000>; - fsl,has-rstcr; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt deleted file mode 100644 index 1eacd6b20ed..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/i2c.txt +++ /dev/null @@ -1,64 +0,0 @@ -* I2C - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a - compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, - mpc5200 or mpc5200b. For the mpc5121, an additional node - "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. - -Recommended properties : - - - interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - fsl,preserve-clocking : boolean; if defined, the clock settings - from the bootloader are preserved (not touched). - - clock-frequency : desired I2C bus clock frequency in Hz. - - fsl,timeout : I2C bus timeout in microseconds. - -Examples : - - /* MPC5121 based board */ - i2c@1740 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5121-i2c", "fsl-i2c"; - reg = <0x1740 0x20>; - interrupts = <11 0x8>; - interrupt-parent = <&ipic>; - clock-frequency = <100000>; - }; - - i2ccontrol@1760 { - compatible = "fsl,mpc5121-i2c-ctrl"; - reg = <0x1760 0x8>; - }; - - /* MPC5200B based board */ - i2c@3d00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d00 0x40>; - interrupts = <2 15 0>; - interrupt-parent = <&mpc5200_pic>; - fsl,preserve-clocking; - }; - - /* MPC8544 base board */ - i2c@3100 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc8544-i2c", "fsl-i2c"; - reg = <0x3100 0x100>; - interrupts = <43 2>; - interrupt-parent = <&mpic>; - clock-frequency = <400000>; - fsl,timeout = <10000>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/lbc.txt b/Documentation/powerpc/dts-bindings/fsl/lbc.txt deleted file mode 100644 index 3300fec501c..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/lbc.txt +++ /dev/null @@ -1,35 +0,0 @@ -* Chipselect/Local Bus - -Properties: -- name : Should be localbus -- #address-cells : Should be either two or three. The first cell is the - chipselect number, and the remaining cells are the - offset into the chipselect. -- #size-cells : Either one or two, depending on how large each chipselect - can be. -- ranges : Each range corresponds to a single chipselect, and cover - the entire access window as configured. - -Example: - localbus@f0010100 { - compatible = "fsl,mpc8272-localbus", - "fsl,pq2-localbus"; - #address-cells = <2>; - #size-cells = <1>; - reg = <f0010100 40>; - - ranges = <0 0 fe000000 02000000 - 1 0 f4500000 00008000>; - - flash@0,0 { - compatible = "jedec-flash"; - reg = <0 0 2000000>; - bank-width = <4>; - device-width = <1>; - }; - - board-control@1,0 { - reg = <1 0 20>; - compatible = "fsl,mpc8272ads-bcsr"; - }; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/mcm.txt b/Documentation/powerpc/dts-bindings/fsl/mcm.txt deleted file mode 100644 index 4ceda9b3b41..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mcm.txt +++ /dev/null @@ -1,64 +0,0 @@ -===================================================================== -MPX LAW & Coherency Module Device Tree Binding -Copyright (C) 2009 Freescale Semiconductor Inc. -===================================================================== - -Local Access Window (LAW) Node - -The LAW node represents the region of CCSR space where local access -windows are configured. For MCM based devices this is the first 4k -of CCSR space that includes CCSRBAR, ALTCBAR, ALTCAR, BPTR, and some -number of local access windows as specified by fsl,num-laws. - -PROPERTIES - - - compatible - Usage: required - Value type: <string> - Definition: Must include "fsl,mcm-law" - - - reg - Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. The value specifies the - physical address offset and length of the CCSR space - registers. - - - fsl,num-laws - Usage: required - Value type: <u32> - Definition: The value specifies the number of local access - windows for this device. - -===================================================================== - -MPX Coherency Module Node - -The MPX LAW node represents the region of CCSR space where MCM config -and error reporting registers exist, this is the second 4k (0x1000) -of CCSR space. - -PROPERTIES - - - compatible - Usage: required - Value type: <string> - Definition: Must include "fsl,CHIP-mcm", "fsl,mcm" where - CHIP is the processor (mpc8641, mpc8610, etc.) - - - reg - Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. The value specifies the - physical address offset and length of the CCSR space - registers. - - - interrupts - Usage: required - Value type: <prop-encoded-array> - - - interrupt-parent - Usage: required - Value type: <phandle> - -===================================================================== diff --git a/Documentation/powerpc/dts-bindings/fsl/mcu-mpc8349emitx.txt b/Documentation/powerpc/dts-bindings/fsl/mcu-mpc8349emitx.txt deleted file mode 100644 index 0f766333b6e..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mcu-mpc8349emitx.txt +++ /dev/null @@ -1,17 +0,0 @@ -Freescale MPC8349E-mITX-compatible Power Management Micro Controller Unit (MCU) - -Required properties: -- compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx". -- reg : should specify I2C address (0x0a). -- #gpio-cells : should be 2. -- gpio-controller : should be present. - -Example: - -mcu@0a { - #gpio-cells = <2>; - compatible = "fsl,mc9s08qg8-mpc8349emitx", - "fsl,mcu-mpc8349emitx"; - reg = <0x0a>; - gpio-controller; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt deleted file mode 100644 index 8832e879891..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mpc5121-psc.txt +++ /dev/null @@ -1,70 +0,0 @@ -MPC5121 PSC Device Tree Bindings - -PSC in UART mode ----------------- - -For PSC in UART mode the needed PSC serial devices -are specified by fsl,mpc5121-psc-uart nodes in the -fsl,mpc5121-immr SoC node. Additionally the PSC FIFO -Controller node fsl,mpc5121-psc-fifo is requered there: - -fsl,mpc5121-psc-uart nodes --------------------------- - -Required properties : - - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" - - cell-index : Index of the PSC in hardware - - reg : Offset and length of the register set for the PSC device - - interrupts : <a b> where a is the interrupt number of the - PSC FIFO Controller and b is a field that represents an - encoding of the sense and level information for the interrupt. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Recommended properties : - - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) - - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) - - -fsl,mpc5121-psc-fifo node -------------------------- - -Required properties : - - compatible : Should be "fsl,mpc5121-psc-fifo" - - reg : Offset and length of the register set for the PSC - FIFO Controller - - interrupts : <a b> where a is the interrupt number of the - PSC FIFO Controller and b is a field that represents an - encoding of the sense and level information for the interrupt. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - - -Example for a board using PSC0 and PSC1 devices in serial mode: - -serial@11000 { - compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; - cell-index = <0>; - reg = <0x11000 0x100>; - interrupts = <40 0x8>; - interrupt-parent = < &ipic >; - fsl,rx-fifo-size = <16>; - fsl,tx-fifo-size = <16>; -}; - -serial@11100 { - compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; - cell-index = <1>; - reg = <0x11100 0x100>; - interrupts = <40 0x8>; - interrupt-parent = < &ipic >; - fsl,rx-fifo-size = <16>; - fsl,tx-fifo-size = <16>; -}; - -pscfifo@11f00 { - compatible = "fsl,mpc5121-psc-fifo"; - reg = <0x11f00 0x100>; - interrupts = <40 0x8>; - interrupt-parent = < &ipic >; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt deleted file mode 100644 index 4ccb2cd5df9..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt +++ /dev/null @@ -1,198 +0,0 @@ -MPC5200 Device Tree Bindings ----------------------------- - -(c) 2006-2009 Secret Lab Technologies Ltd -Grant Likely <grant.likely@secretlab.ca> - -Naming conventions ------------------- -For mpc5200 on-chip devices, the format for each compatible value is -<chip>-<device>[-<mode>]. The OS should be able to match a device driver -to the device based solely on the compatible value. If two drivers -match on the compatible list; the 'most compatible' driver should be -selected. - -The split between the MPC5200 and the MPC5200B leaves a bit of a -conundrum. How should the compatible property be set up to provide -maximum compatibility information; but still accurately describe the -chip? For the MPC5200; the answer is easy. Most of the SoC devices -originally appeared on the MPC5200. Since they didn't exist anywhere -else; the 5200 compatible properties will contain only one item; -"fsl,mpc5200-<device>". - -The 5200B is almost the same as the 5200, but not quite. It fixes -silicon bugs and it adds a small number of enhancements. Most of the -devices either provide exactly the same interface as on the 5200. A few -devices have extra functions but still have a backwards compatible mode. -To express this information as completely as possible, 5200B device trees -should have two items in the compatible list: - compatible = "fsl,mpc5200b-<device>","fsl,mpc5200-<device>"; - -It is *strongly* recommended that 5200B device trees follow this convention -(instead of only listing the base mpc5200 item). - -ie. ethernet on mpc5200: compatible = "fsl,mpc5200-fec"; - ethernet on mpc5200b: compatible = "fsl,mpc5200b-fec", "fsl,mpc5200-fec"; - -Modal devices, like PSCs, also append the configured function to the -end of the compatible field. ie. A PSC in i2s mode would specify -"fsl,mpc5200-psc-i2s", not "fsl,mpc5200-i2s". This convention is chosen to -avoid naming conflicts with non-psc devices providing the same -function. For example, "fsl,mpc5200-spi" and "fsl,mpc5200-psc-spi" describe -the mpc5200 simple spi device and a PSC spi mode respectively. - -At the time of writing, exact chip may be either 'fsl,mpc5200' or -'fsl,mpc5200b'. - -The soc node ------------- -This node describes the on chip SOC peripherals. Every mpc5200 based -board will have this node, and as such there is a common naming -convention for SOC devices. - -Required properties: -name description ----- ----------- -ranges Memory range of the internal memory mapped registers. - Should be <0 [baseaddr] 0xc000> -reg Should be <[baseaddr] 0x100> -compatible mpc5200: "fsl,mpc5200-immr" - mpc5200b: "fsl,mpc5200b-immr" -system-frequency 'fsystem' frequency in Hz; XLB, IPB, USB and PCI - clocks are derived from the fsystem clock. -bus-frequency IPB bus frequency in Hz. Clock rate - used by most of the soc devices. - -soc child nodes ---------------- -Any on chip SOC devices available to Linux must appear as soc5200 child nodes. - -Note: The tables below show the value for the mpc5200. A mpc5200b device -tree should use the "fsl,mpc5200b-<device>","fsl,mpc5200-<device>" form. - -Required soc5200 child nodes: -name compatible Description ----- ---------- ----------- -cdm@<addr> fsl,mpc5200-cdm Clock Distribution -interrupt-controller@<addr> fsl,mpc5200-pic need an interrupt - controller to boot -bestcomm@<addr> fsl,mpc5200-bestcomm Bestcomm DMA controller - -Recommended soc5200 child nodes; populate as needed for your board -name compatible Description ----- ---------- ----------- -timer@<addr> fsl,mpc5200-gpt General purpose timers -gpio@<addr> fsl,mpc5200-gpio MPC5200 simple gpio controller -gpio@<addr> fsl,mpc5200-gpio-wkup MPC5200 wakeup gpio controller -rtc@<addr> fsl,mpc5200-rtc Real time clock -mscan@<addr> fsl,mpc5200-mscan CAN bus controller -pci@<addr> fsl,mpc5200-pci PCI bridge -serial@<addr> fsl,mpc5200-psc-uart PSC in serial mode -i2s@<addr> fsl,mpc5200-psc-i2s PSC in i2s mode -ac97@<addr> fsl,mpc5200-psc-ac97 PSC in ac97 mode -spi@<addr> fsl,mpc5200-psc-spi PSC in spi mode -irda@<addr> fsl,mpc5200-psc-irda PSC in IrDA mode -spi@<addr> fsl,mpc5200-spi MPC5200 spi device -ethernet@<addr> fsl,mpc5200-fec MPC5200 ethernet device -ata@<addr> fsl,mpc5200-ata IDE ATA interface -i2c@<addr> fsl,mpc5200-i2c I2C controller -usb@<addr> fsl,mpc5200-ohci,ohci-be USB controller -xlb@<addr> fsl,mpc5200-xlb XLB arbitrator - -fsl,mpc5200-gpt nodes ---------------------- -On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board -design supports the internal wdt, then the device node for GPT0 should -include the empty property 'fsl,has-wdt'. Note that this does not activate -the watchdog. The timer will function as a GPT if the timer api is used, and -it will function as watchdog if the watchdog device is used. The watchdog -mode has priority over the gpt mode, i.e. if the watchdog is activated, any -gpt api call to this timer will fail with -EBUSY. - -If you add the property - fsl,wdt-on-boot = <n>; -GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it. -If n>0, the watchdog is started with a timeout of n seconds. If n=0, the -configuration of the watchdog is not touched. This is useful in two cases: -- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later; -- do not touch a configuration assigned by the boot loader which supervises - the boot process itself. - -The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option. - -An mpc5200-gpt can be used as a single line GPIO controller. To do so, -add the following properties to the gpt node: - gpio-controller; - #gpio-cells = <2>; -When referencing the GPIO line from another node, the first cell must always -be zero and the second cell represents the gpio flags and described in the -gpio device tree binding. - -An mpc5200-gpt can be used as a single line edge sensitive interrupt -controller. To do so, add the following properties to the gpt node: - interrupt-controller; - #interrupt-cells = <1>; -When referencing the IRQ line from another node, the cell represents the -sense mode; 1 for edge rising, 2 for edge falling. - -fsl,mpc5200-psc nodes ---------------------- -The PSCs should include a cell-index which is the index of the PSC in -hardware. cell-index is used to determine which shared SoC registers to -use when setting up PSC clocking. cell-index number starts at '0'. ie: - PSC1 has 'cell-index = <0>' - PSC4 has 'cell-index = <3>' - -PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in -i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the -compatible field. - - -fsl,mpc5200-gpio and fsl,mpc5200-gpio-wkup nodes ------------------------------------------------- -Each GPIO controller node should have the empty property gpio-controller and -#gpio-cells set to 2. First cell is the GPIO number which is interpreted -according to the bit numbers in the GPIO control registers. The second cell -is for flags which is currently unused. - -fsl,mpc5200-fec nodes ---------------------- -The FEC node can specify one of the following properties to configure -the MII link: -- fsl,7-wire-mode - An empty property that specifies the link uses 7-wire - mode instead of MII -- current-speed - Specifies that the MII should be configured for a fixed - speed. This property should contain two cells. The - first cell specifies the speed in Mbps and the second - should be '0' for half duplex and '1' for full duplex -- phy-handle - Contains a phandle to an Ethernet PHY. - -Interrupt controller (fsl,mpc5200-pic) node -------------------------------------------- -The mpc5200 pic binding splits hardware IRQ numbers into two levels. The -split reflects the layout of the PIC hardware itself, which groups -interrupts into one of three groups; CRIT, MAIN or PERP. Also, the -Bestcomm dma engine has it's own set of interrupt sources which are -cascaded off of peripheral interrupt 0, which the driver interprets as a -fourth group, SDMA. - -The interrupts property for device nodes using the mpc5200 pic consists -of three cells; <L1 L2 level> - - L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3] - L2 := interrupt number; directly mapped from the value in the - "ICTL PerStat, MainStat, CritStat Encoded Register" - level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3] - -For external IRQs, use the following interrupt property values (how to -specify external interrupts is a frequently asked question): -External interrupts: - external irq0: interrupts = <0 0 n>; - external irq1: interrupts = <1 1 n>; - external irq2: interrupts = <1 2 n>; - external irq3: interrupts = <1 3 n>; -'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low) - -fsl,mpc5200-mscan nodes ------------------------ -See file can.txt in this directory. diff --git a/Documentation/powerpc/dts-bindings/fsl/mpic.txt b/Documentation/powerpc/dts-bindings/fsl/mpic.txt deleted file mode 100644 index 71e39cf3215..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/mpic.txt +++ /dev/null @@ -1,42 +0,0 @@ -* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores - -The OpenPIC specification does not specify which interrupt source has to -become which interrupt number. This is up to the software implementation -of the interrupt controller. The only requirement is that every -interrupt source has to have an unique interrupt number / vector number. -To accomplish this the current implementation assigns the number zero to -the first source, the number one to the second source and so on until -all interrupt sources have their unique number. -Usually the assigned vector number equals the interrupt number mentioned -in the documentation for a given core / CPU. This is however not true -for the e500 cores (MPC85XX CPUs) where the documentation distinguishes -between internal and external interrupt sources and starts counting at -zero for both of them. - -So what to write for external interrupt source X or internal interrupt -source Y into the device tree? Here is an example: - -The memory map for the interrupt controller in the MPC8544[0] shows, -that the first interrupt source starts at 0x5_0000 (PIC Register Address -Map-Interrupt Source Configuration Registers). This source becomes the -number zero therefore: - External interrupt 0 = interrupt number 0 - External interrupt 1 = interrupt number 1 - External interrupt 2 = interrupt number 2 - ... -Every interrupt number allocates 0x20 bytes register space. So to get -its number it is sufficient to shift the lower 16bits to right by five. -So for the external interrupt 10 we have: - 0x0140 >> 5 = 10 - -After the external sources, the internal sources follow. The in core I2C -controller on the MPC8544 for instance has the internal source number -27. Oo obtain its interrupt number we take the lower 16bits of its memory -address (0x5_0560) and shift it right: - 0x0560 >> 5 = 43 - -Therefore the I2C device node for the MPC8544 CPU has to have the -interrupt number 43 specified in the device tree. - -[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual - MPC8544ERM Rev. 1 10/2007 diff --git a/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt b/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt deleted file mode 100644 index bcc30bac683..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/msi-pic.txt +++ /dev/null @@ -1,36 +0,0 @@ -* Freescale MSI interrupt controller - -Required properties: -- compatible : compatible list, contains 2 entries, - first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572, - etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on - the parent type. -- reg : should contain the address and the length of the shared message - interrupt register set. -- msi-available-ranges: use <start count> style section to define which - msi interrupt can be used in the 256 msi interrupts. This property is - optional, without this, all the 256 MSI interrupts can be used. -- interrupts : each one of the interrupts here is one entry per 32 MSIs, - and routed to the host interrupt controller. the interrupts should - be set as edge sensitive. -- interrupt-parent: the phandle for the interrupt controller - that services interrupts for this device. for 83xx cpu, the interrupts - are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed - to MPIC. - -Example: - msi@41600 { - compatible = "fsl,mpc8610-msi", "fsl,mpic-msi"; - reg = <0x41600 0x80>; - msi-available-ranges = <0 0x100>; - interrupts = < - 0xe0 0 - 0xe1 0 - 0xe2 0 - 0xe3 0 - 0xe4 0 - 0xe5 0 - 0xe6 0 - 0xe7 0>; - interrupt-parent = <&mpic>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/pmc.txt b/Documentation/powerpc/dts-bindings/fsl/pmc.txt deleted file mode 100644 index 07256b7ffca..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/pmc.txt +++ /dev/null @@ -1,63 +0,0 @@ -* Power Management Controller - -Properties: -- compatible: "fsl,<chip>-pmc". - - "fsl,mpc8349-pmc" should be listed for any chip whose PMC is - compatible. "fsl,mpc8313-pmc" should also be listed for any chip - whose PMC is compatible, and implies deep-sleep capability. - - "fsl,mpc8548-pmc" should be listed for any chip whose PMC is - compatible. "fsl,mpc8536-pmc" should also be listed for any chip - whose PMC is compatible, and implies deep-sleep capability. - - "fsl,mpc8641d-pmc" should be listed for any chip whose PMC is - compatible; all statements below that apply to "fsl,mpc8548-pmc" also - apply to "fsl,mpc8641d-pmc". - - Compatibility does not include bit assignments in SCCR/PMCDR/DEVDISR; these - bit assignments are indicated via the sleep specifier in each device's - sleep property. - -- reg: For devices compatible with "fsl,mpc8349-pmc", the first resource - is the PMC block, and the second resource is the Clock Configuration - block. - - For devices compatible with "fsl,mpc8548-pmc", the first resource - is a 32-byte block beginning with DEVDISR. - -- interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first - resource is the PMC block interrupt. - -- fsl,mpc8313-wakeup-timer: For "fsl,mpc8313-pmc"-compatible devices, - this is a phandle to an "fsl,gtm" node on which timer 4 can be used as - a wakeup source from deep sleep. - -Sleep specifiers: - - fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit - that is set in the cell, the corresponding bit in SCCR will be saved - and cleared on suspend, and restored on resume. This sleep controller - supports disabling and resuming devices at any time. - - fsl,mpc8536-pmc: Sleep specifiers consist of three cells, the third of - which will be ORed into PMCDR upon suspend, and cleared from PMCDR - upon resume. The first two cells are as described for fsl,mpc8578-pmc. - This sleep controller only supports disabling devices during system - sleep, or permanently. - - fsl,mpc8548-pmc: Sleep specifiers consist of one or two cells, the - first of which will be ORed into DEVDISR (and the second into - DEVDISR2, if present -- this cell should be zero or absent if the - hardware does not have DEVDISR2) upon a request for permanent device - disabling. This sleep controller does not support configuring devices - to disable during system sleep (unless supported by another compatible - match), or dynamically. - -Example: - - power@b00 { - compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc"; - reg = <0xb00 0x100 0xa00 0x100>; - interrupts = <80 8>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/sata.txt b/Documentation/powerpc/dts-bindings/fsl/sata.txt deleted file mode 100644 index b46bcf46c3d..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/sata.txt +++ /dev/null @@ -1,29 +0,0 @@ -* Freescale 8xxx/3.0 Gb/s SATA nodes - -SATA nodes are defined to describe on-chip Serial ATA controllers. -Each SATA port should have its own node. - -Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-sata", where CHIP is the processor - (mpc8315, mpc8379, etc.) and the second is - "fsl,pq-sata" -- interrupts : <interrupt mapping for SATA IRQ> -- cell-index : controller index. - 1 for controller @ 0x18000 - 2 for controller @ 0x19000 - 3 for controller @ 0x1a000 - 4 for controller @ 0x1b000 - -Optional properties: -- interrupt-parent : optional, if needed for interrupt mapping -- reg : <registers mapping> - -Example: - sata@18000 { - compatible = "fsl,mpc8379-sata", "fsl,pq-sata"; - reg = <0x18000 0x1000>; - cell-index = <1>; - interrupts = <2c 8>; - interrupt-parent = < &ipic >; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/sec.txt b/Documentation/powerpc/dts-bindings/fsl/sec.txt deleted file mode 100644 index 2b6f2d45c45..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/sec.txt +++ /dev/null @@ -1,68 +0,0 @@ -Freescale SoC SEC Security Engines - -Required properties: - -- compatible : Should contain entries for this and backward compatible - SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0" -- reg : Offset and length of the register set for the device -- interrupts : the SEC's interrupt number -- fsl,num-channels : An integer representing the number of channels - available. -- fsl,channel-fifo-len : An integer representing the number of - descriptor pointers each channel fetch fifo can hold. -- fsl,exec-units-mask : The bitmask representing what execution units - (EUs) are available. It's a single 32-bit cell. EU information - should be encoded following the SEC's Descriptor Header Dword - EU_SEL0 field documentation, i.e. as follows: - - bit 0 = reserved - should be 0 - bit 1 = set if SEC has the ARC4 EU (AFEU) - bit 2 = set if SEC has the DES/3DES EU (DEU) - bit 3 = set if SEC has the message digest EU (MDEU/MDEU-A) - bit 4 = set if SEC has the random number generator EU (RNG) - bit 5 = set if SEC has the public key EU (PKEU) - bit 6 = set if SEC has the AES EU (AESU) - bit 7 = set if SEC has the Kasumi EU (KEU) - bit 8 = set if SEC has the CRC EU (CRCU) - bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B) - -remaining bits are reserved for future SEC EUs. - -- fsl,descriptor-types-mask : The bitmask representing what descriptors - are available. It's a single 32-bit cell. Descriptor type information - should be encoded following the SEC's Descriptor Header Dword DESC_TYPE - field documentation, i.e. as follows: - - bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type - bit 1 = set if SEC supports the ipsec_esp descriptor type - bit 2 = set if SEC supports the common_nonsnoop desc. type - bit 3 = set if SEC supports the 802.11i AES ccmp desc. type - bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type - bit 5 = set if SEC supports the srtp descriptor type - bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type - bit 7 = set if SEC supports the pkeu_assemble descriptor type - bit 8 = set if SEC supports the aesu_key_expand_output desc.type - bit 9 = set if SEC supports the pkeu_ptmul descriptor type - bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type - bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type - - ..and so on and so forth. - -Optional properties: - -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Example: - - /* MPC8548E */ - crypto@30000 { - compatible = "fsl,sec2.1", "fsl,sec2.0"; - reg = <0x30000 0x10000>; - interrupts = <29 2>; - interrupt-parent = <&mpic>; - fsl,num-channels = <4>; - fsl,channel-fifo-len = <24>; - fsl,exec-units-mask = <0xfe>; - fsl,descriptor-types-mask = <0x12b0ebf>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/spi.txt b/Documentation/powerpc/dts-bindings/fsl/spi.txt deleted file mode 100644 index 777abd7399d..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/spi.txt +++ /dev/null @@ -1,53 +0,0 @@ -* SPI (Serial Peripheral Interface) - -Required properties: -- cell-index : QE SPI subblock index. - 0: QE subblock SPI1 - 1: QE subblock SPI2 -- compatible : should be "fsl,spi". -- mode : the SPI operation mode, it can be "cpu" or "cpu-qe". -- reg : Offset and length of the register set for the device -- interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. -- interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Optional properties: -- gpios : specifies the gpio pins to be used for chipselects. - The gpios will be referred to as reg = <index> in the SPI child nodes. - If unspecified, a single SPI device without a chip select can be used. - -Example: - spi@4c0 { - cell-index = <0>; - compatible = "fsl,spi"; - reg = <4c0 40>; - interrupts = <82 0>; - interrupt-parent = <700>; - mode = "cpu"; - gpios = <&gpio 18 1 // device reg=<0> - &gpio 19 1>; // device reg=<1> - }; - - -* eSPI (Enhanced Serial Peripheral Interface) - -Required properties: -- compatible : should be "fsl,mpc8536-espi". -- reg : Offset and length of the register set for the device. -- interrupts : should contain eSPI interrupt, the device has one interrupt. -- fsl,espi-num-chipselects : the number of the chipselect signals. - -Example: - spi@110000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc8536-espi"; - reg = <0x110000 0x1000>; - interrupts = <53 0x2>; - interrupt-parent = <&mpic>; - fsl,espi-num-chipselects = <4>; - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/ssi.txt b/Documentation/powerpc/dts-bindings/fsl/ssi.txt deleted file mode 100644 index 5ff76c9c57d..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/ssi.txt +++ /dev/null @@ -1,73 +0,0 @@ -Freescale Synchronous Serial Interface - -The SSI is a serial device that communicates with audio codecs. It can -be programmed in AC97, I2S, left-justified, or right-justified modes. - -Required properties: -- compatible: Compatible list, contains "fsl,ssi". -- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. -- reg: Offset and length of the register set for the device. -- interrupts: <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and - level information for the interrupt. This should be - encoded based on the information in section 2) - depending on the type of interrupt controller you - have. -- interrupt-parent: The phandle for the interrupt controller that - services interrupts for this device. -- fsl,mode: The operating mode for the SSI interface. - "i2s-slave" - I2S mode, SSI is clock slave - "i2s-master" - I2S mode, SSI is clock master - "lj-slave" - left-justified mode, SSI is clock slave - "lj-master" - l.j. mode, SSI is clock master - "rj-slave" - right-justified mode, SSI is clock slave - "rj-master" - r.j., SSI is clock master - "ac97-slave" - AC97 mode, SSI is clock slave - "ac97-master" - AC97 mode, SSI is clock master -- fsl,playback-dma: Phandle to a node for the DMA channel to use for - playback of audio. This is typically dictated by SOC - design. See the notes below. -- fsl,capture-dma: Phandle to a node for the DMA channel to use for - capture (recording) of audio. This is typically dictated - by SOC design. See the notes below. -- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. - This number is the maximum allowed value for SFCSR[TFWM0]. -- fsl,ssi-asynchronous: - If specified, the SSI is to be programmed in asynchronous - mode. In this mode, pins SRCK, STCK, SRFS, and STFS must - all be connected to valid signals. In synchronous mode, - SRCK and SRFS are ignored. Asynchronous mode allows - playback and capture to use different sample sizes and - sample rates. Some drivers may require that SRCK and STCK - be connected together, and SRFS and STFS be connected - together. This would still allow different sample sizes, - but not different sample rates. - -Optional properties: -- codec-handle: Phandle to a 'codec' node that defines an audio - codec connected to this SSI. This node is typically - a child of an I2C or other control node. - -Child 'codec' node required properties: -- compatible: Compatible list, contains the name of the codec - -Child 'codec' node optional properties: -- clock-frequency: The frequency of the input clock, which typically comes - from an on-board dedicated oscillator. - -Notes on fsl,playback-dma and fsl,capture-dma: - -On SOCs that have an SSI, specific DMA channels are hard-wired for playback -and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for -playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for -playback and DMA channel 3 for capture. The developer can choose which -DMA controller to use, but the channels themselves are hard-wired. The -purpose of these two properties is to represent this hardware design. - -The device tree nodes for the DMA channels that are referenced by -"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with -"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. -"fsl,mpc8610-dma-channel") can remain. If these nodes are left as -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA -drivers (fsldma) will attempt to use them, and it will conflict with the -sound drivers. diff --git a/Documentation/powerpc/dts-bindings/fsl/tsec.txt b/Documentation/powerpc/dts-bindings/fsl/tsec.txt deleted file mode 100644 index edb7ae19e86..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/tsec.txt +++ /dev/null @@ -1,76 +0,0 @@ -* MDIO IO device - -The MDIO is a bus to which the PHY devices are connected. For each -device that exists on this bus, a child node should be created. See -the definition of the PHY node in booting-without-of.txt for an example -of how to define a PHY. - -Required properties: - - reg : Offset and length of the register set for the device - - compatible : Should define the compatible device type for the - mdio. Currently, this is most likely to be "fsl,gianfar-mdio" - -Example: - - mdio@24520 { - reg = <24520 20>; - compatible = "fsl,gianfar-mdio"; - - ethernet-phy@0 { - ...... - }; - }; - -* TBI Internal MDIO bus - -As of this writing, every tsec is associated with an internal TBI PHY. -This PHY is accessed through the local MDIO bus. These buses are defined -similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". -The TBI PHYs underneath them are similar to normal PHYs, but the reg property -is considered instructive, rather than descriptive. The reg property should -be chosen so it doesn't interfere with other PHYs on the bus. - -* Gianfar-compatible ethernet nodes - -Properties: - - - device_type : Should be "network" - - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" - - compatible : Should be "gianfar" - - reg : Offset and length of the register set for the device - - local-mac-address : List of bytes representing the ethernet address of - this controller - - interrupts : For FEC devices, the first interrupt is the device's - interrupt. For TSEC and eTSEC devices, the first interrupt is - transmit, the second is receive, and the third is error. - - phy-handle : The phandle for the PHY connected to this ethernet - controller. - - fixed-link : <a b c d e> where a is emulated phy id - choose any, - but unique to the all specified fixed-links, b is duplex - 0 half, - 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no - pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause. - - phy-connection-type : a string naming the controller/PHY interface type, - i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii", - "tbi", or "rtbi". This property is only really needed if the connection - is of type "rgmii-id", as all other connection types are detected by - hardware. - - fsl,magic-packet : If present, indicates that the hardware supports - waking up via magic packet. - - bd-stash : If present, indicates that the hardware supports stashing - buffer descriptors in the L2. - - rx-stash-len : Denotes the number of bytes of a received buffer to stash - in the L2. - - rx-stash-idx : Denotes the index of the first byte from the received - buffer to stash in the L2. - -Example: - ethernet@24000 { - device_type = "network"; - model = "TSEC"; - compatible = "gianfar"; - reg = <0x24000 0x1000>; - local-mac-address = [ 00 E0 0C 00 73 00 ]; - interrupts = <29 2 30 2 34 2>; - interrupt-parent = <&mpic>; - phy-handle = <&phy0> - }; diff --git a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt b/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt deleted file mode 100644 index a48b2cadc7f..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt +++ /dev/null @@ -1,63 +0,0 @@ -Freescale Localbus UPM programmed to work with NAND flash - -Required properties: -- compatible : "fsl,upm-nand". -- reg : should specify localbus chip select and size used for the chip. -- fsl,upm-addr-offset : UPM pattern offset for the address latch. -- fsl,upm-cmd-offset : UPM pattern offset for the command latch. - -Optional properties: -- fsl,upm-wait-flags : add chip-dependent short delays after running the - UPM pattern (0x1), after writing a data byte (0x2) or after - writing out a buffer (0x4). -- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support. - The corresponding address lines are used to select the chip. -- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins - (R/B#). For multi-chip devices, "n" GPIO definitions are required - according to the number of chips. -- chip-delay : chip dependent delay for transfering data from array to - read registers (tR). Required if property "gpios" is not used - (R/B# pins not connected). - -Examples: - -upm@1,0 { - compatible = "fsl,upm-nand"; - reg = <1 0 1>; - fsl,upm-addr-offset = <16>; - fsl,upm-cmd-offset = <8>; - gpios = <&qe_pio_e 18 0>; - - flash { - #address-cells = <1>; - #size-cells = <1>; - compatible = "..."; - - partition@0 { - ... - }; - }; -}; - -upm@3,0 { - #address-cells = <0>; - #size-cells = <0>; - compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand"; - reg = <3 0x0 0x800>; - fsl,upm-addr-offset = <0x10>; - fsl,upm-cmd-offset = <0x08>; - /* Multi-chip NAND device */ - fsl,upm-addr-line-cs-offsets = <0x0 0x200>; - fsl,upm-wait-flags = <0x5>; - chip-delay = <25>; // in micro-seconds - - nand@0 { - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "fs"; - reg = <0x00000000 0x10000000>; - }; - }; -}; diff --git a/Documentation/powerpc/dts-bindings/fsl/usb.txt b/Documentation/powerpc/dts-bindings/fsl/usb.txt deleted file mode 100644 index bd5723f0b67..00000000000 --- a/Documentation/powerpc/dts-bindings/fsl/usb.txt +++ /dev/null @@ -1,81 +0,0 @@ -Freescale SOC USB controllers - -The device node for a USB controller that is part of a Freescale -SOC is as described in the document "Open Firmware Recommended -Practice : Universal Serial Bus" with the following modifications -and additions : - -Required properties : - - compatible : Should be "fsl-usb2-mph" for multi port host USB - controllers, or "fsl-usb2-dr" for dual role USB controllers - or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121 - - phy_type : For multi port host USB controllers, should be one of - "ulpi", or "serial". For dual role USB controllers, should be - one of "ulpi", "utmi", "utmi_wide", or "serial". - - reg : Offset and length of the register set for the device - - port0 : boolean; if defined, indicates port0 is connected for - fsl-usb2-mph compatible controllers. Either this property or - "port1" (or both) must be defined for "fsl-usb2-mph" compatible - controllers. - - port1 : boolean; if defined, indicates port1 is connected for - fsl-usb2-mph compatible controllers. Either this property or - "port0" (or both) must be defined for "fsl-usb2-mph" compatible - controllers. - - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible - controllers. Can be "host", "peripheral", or "otg". Default to - "host" if not defined for backward compatibility. - -Recommended properties : - - interrupts : <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and level - information for the interrupt. This should be encoded based on - the information in section 2) depending on the type of interrupt - controller you have. - - interrupt-parent : the phandle for the interrupt controller that - services interrupts for this device. - -Optional properties : - - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the - port power polarity of internal PHY signal DRVVBUS is inverted. - - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates - the PWR_FAULT signal polarity is inverted. - -Example multi port host USB controller device node : - usb@22000 { - compatible = "fsl-usb2-mph"; - reg = <22000 1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <700>; - interrupts = <27 1>; - phy_type = "ulpi"; - port0; - port1; - }; - -Example dual role USB controller device node : - usb@23000 { - compatible = "fsl-usb2-dr"; - reg = <23000 1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <700>; - interrupts = <26 1>; - dr_mode = "otg"; - phy = "ulpi"; - }; - -Example dual role USB controller device node for MPC5121ADS: - - usb@4000 { - compatible = "fsl,mpc5121-usb2-dr"; - reg = <0x4000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = < &ipic >; - interrupts = <44 0x8>; - dr_mode = "otg"; - phy_type = "utmi_wide"; - fsl,invert-drvvbus; - fsl,invert-pwr-fault; - }; |