Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
  powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
  MAINTAINERS: Add PowerPC patterns
  powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
  powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
  powerpc: Make "intspec" pointers in irq_host->xlate() const
  powerpc/8xx: DTLB Miss cleanup
  powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
  powerpc/8xx: Start using dcbX instructions in various copy routines
  powerpc/8xx: Restore _PAGE_WRITETHRU
  powerpc/8xx: Add missing Guarded setting in DTLB Error.
  powerpc/8xx: Fixup DAR from buggy dcbX instructions.
  powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
  powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
  powerpc/8xx: Invalidate non present TLBs
  powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
  pseries/pseries: Add code to online/offline CPUs of a DLPAR node
  powerpc: stop_this_cpu: remove the cpu from the online map.
  powerpc/pseries: Add kernel based CPU DLPAR handling
  sysfs/cpu: Add probe/release files
  powerpc/pseries: Kernel DLPAR Infrastructure
  ...

2 files changed, 20 insertions, 1 deletions

diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt
index e8b5bc24d0a..39e941515a3 100644
--- a/Documentation/powerpc/dts-bindings/fsl/board.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/board.txt
@@ -20,12 +20,16 @@ Required properities:
 - compatible : should be "fsl,fpga-pixis".
 - reg : should contain the address and the length of the FPPGA register
   set.
+- interrupt-parent: should specify phandle for the interrupt controller.
+- interrupts : should specify event (wakeup) IRQ.
 
 Example (MPC8610HPCD):
 
 	board-control@e8000000 {
 		compatible = "fsl,fpga-pixis";
 		reg = <0xe8000000 32>;
+		interrupt-parent = <&mpic>;
+		interrupts = <8 8>;
 	};
 
 * Freescale BCSR GPIO banks
diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
index cabc780f725..5c6602dbfdc 100644
--- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
@@ -103,7 +103,22 @@ fsl,mpc5200-gpt nodes
 ---------------------
 On the mpc5200 and 5200b, GPT0 has a watchdog timer function.  If the board
 design supports the internal wdt, then the device node for GPT0 should
-include the empty property 'fsl,has-wdt'.
+include the empty property 'fsl,has-wdt'.  Note that this does not activate
+the watchdog.  The timer will function as a GPT if the timer api is used, and
+it will function as watchdog if the watchdog device is used.  The watchdog
+mode has priority over the gpt mode, i.e. if the watchdog is activated, any
+gpt api call to this timer will fail with -EBUSY.
+
+If you add the property
+	fsl,wdt-on-boot = <n>;
+GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it.
+If n>0, the watchdog is started with a timeout of n seconds.  If n=0, the
+configuration of the watchdog is not touched.  This is useful in two cases:
+- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later;
+- do not touch a configuration assigned by the boot loader which supervises
+  the boot process itself.
+
+The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option.
 
 An mpc5200-gpt can be used as a single line GPIO controller.  To do so,
 add the following properties to the gpt node: