Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
  ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
  ALSA: hda - Keep EAPD turned on for old Conexant chips
  ALSA: hda/realtek - Fix missing volume controls with ALC260
  ASoC: wm8940: Properly set codec->dapm.bias_level
  ALSA: hda - Fix pin-config for ASUS W90V
  ALSA: hda - Fix surround/CLFE headphone and speaker pins order
  ALSA: hda - Fix typo
  ALSA: Update the sound git tree URL
  ALSA: HDA: Add new revision for ALC662
  ASoC: max98095: Convert codec->hw_write to snd_soc_write
  ASoC: keep pointer to resource so it can be freed
  ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
  ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
  ASoC: da7210: Add support for line out and DAC
  ASoC: da7210: Add support for DAPM
  ALSA: hda/realtek - Fix DAC assignments of multiple speakers
  ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
  ASoC: Set sgtl5000->ldo in ldo_regulator_register
  ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
  ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
  ...

1 files changed, 53 insertions, 2 deletions

diff --git a/Documentation/sound/alsa/HD-Audio.txt b/Documentation/sound/alsa/HD-Audio.txt
index c82beb00763..03e2771ddee 100644
--- a/Documentation/sound/alsa/HD-Audio.txt
+++ b/Documentation/sound/alsa/HD-Audio.txt
@@ -447,7 +447,10 @@ The file needs to have a line `[codec]`.  The next line should contain
 three numbers indicating the codec vendor-id (0x12345678 in the
 example), the codec subsystem-id (0xabcd1234) and the address (2) of
 the codec.  The rest patch entries are applied to this specified codec
-until another codec entry is given.
+until another codec entry is given.  Passing 0 or a negative number to
+the first or the second value will make the check of the corresponding
+field be skipped.  It'll be useful for really broken devices that don't
+initialize SSID properly.
 
 The `[model]` line allows to change the model name of the each codec.
 In the example above, it will be changed to model=auto.
@@ -491,7 +494,7 @@ Also, the codec chip name can be rewritten via `[chip_name]` line.
 The hd-audio driver reads the file via request_firmware().  Thus,
 a patch file has to be located on the appropriate firmware path,
 typically, /lib/firmware.  For example, when you pass the option
-`patch=hda-init.fw`, the file /lib/firmware/hda-init-fw must be
+`patch=hda-init.fw`, the file /lib/firmware/hda-init.fw must be
 present.
 
 The patch module option is specific to each card instance, and you
@@ -524,6 +527,54 @@ power-saving.  See /sys/module/snd_hda_intel/parameters/power_save to
 check the current value.  If it's non-zero, the feature is turned on.
 
 
+Tracepoints
+~~~~~~~~~~~
+The hd-audio driver gives a few basic tracepoints.
+`hda:hda_send_cmd` traces each CORB write while `hda:hda_get_response`
+traces the response from RIRB (only when read from the codec driver).
+`hda:hda_bus_reset` traces the bus-reset due to fatal error, etc,
+`hda:hda_unsol_event` traces the unsolicited events, and
+`hda:hda_power_down` and `hda:hda_power_up` trace the power down/up
+via power-saving behavior.
+
+Enabling all tracepoints can be done like
+------------------------------------------------------------------------
+  # echo 1 > /sys/kernel/debug/tracing/events/hda/enable
+------------------------------------------------------------------------
+then after some commands, you can traces from
+/sys/kernel/debug/tracing/trace file.  For example, when you want to
+trace what codec command is sent, enable the tracepoint like:
+------------------------------------------------------------------------
+  # cat /sys/kernel/debug/tracing/trace
+  # tracer: nop
+  #
+  #       TASK-PID    CPU#    TIMESTAMP  FUNCTION
+  #          | |       |          |         |
+         <...>-7807  [002] 105147.774889: hda_send_cmd: [0:0] val=e3a019
+         <...>-7807  [002] 105147.774893: hda_send_cmd: [0:0] val=e39019
+         <...>-7807  [002] 105147.999542: hda_send_cmd: [0:0] val=e3a01a
+         <...>-7807  [002] 105147.999543: hda_send_cmd: [0:0] val=e3901a
+         <...>-26764 [001] 349222.837143: hda_send_cmd: [0:0] val=e3a019
+         <...>-26764 [001] 349222.837148: hda_send_cmd: [0:0] val=e39019
+         <...>-26764 [001] 349223.058539: hda_send_cmd: [0:0] val=e3a01a
+         <...>-26764 [001] 349223.058541: hda_send_cmd: [0:0] val=e3901a
+------------------------------------------------------------------------
+Here `[0:0]` indicates the card number and the codec address, and
+`val` shows the value sent to the codec, respectively.  The value is
+a packed value, and you can decode it via hda-decode-verb program
+included in hda-emu package below.  For example, the value e3a019 is
+to set the left output-amp value to 25.
+------------------------------------------------------------------------
+  % hda-decode-verb 0xe3a019
+  raw value = 0x00e3a019
+  cid = 0, nid = 0x0e, verb = 0x3a0, parm = 0x19
+  raw value: verb = 0x3a0, parm = 0x19
+  verbname = set_amp_gain_mute
+  amp raw val = 0xa019
+  output, left, idx=0, mute=0, val=25
+------------------------------------------------------------------------
+
+
 Development Tree
 ~~~~~~~~~~~~~~~~
 The latest development codes for HD-audio are found on sound git tree: