[PATCH] spi: stabilize PIO mode transfers on PXA2xx systems

Stabilize PIO mode transfers against a range of word sizes and FIFO
thresholds and fixes word size setup/override issues.

1) 16 and 32 bit DMA/PIO transfers broken due to timing differences.
2) Potential for bad transfer counts due to transfer size assumptions.
3) Setup function broken is multiple ways.
4) Per transfer bit_per_word changes break DMA setup in pump_tranfers.
5) False positive timeout are not errors.
6) Changes in pxa2xx_spi_chip not effective in calls to setup.
7) Timeout scaling wrong for PXA255 NSSP.
8) Driver leaks memory while busy during unloading.

Known issues:

SPI_CS_HIGH and SPI_LSB_FIRST settings in struct spi_device are not handled.

Testing:

This patch has been test against the "random length, random bits/word,
random data (verified on loopback) and stepped baud rate by octaves
(3.6MHz to 115kHz)" test.  It is robust in PIO mode, using any
combination of tx and rx thresholds, and also in DMA mode (which
internally computes the thresholds).

Much thanks to Ned Forrester for exhaustive reviews, fixes and testing.
The driver is substantially better for his efforts.

Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

1 files changed, 8 insertions, 8 deletions

diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
index a1e0ee20f59..f9717fe9bd8 100644
--- a/Documentation/spi/pxa2xx
+++ b/Documentation/spi/pxa2xx
@@ -102,7 +102,7 @@ struct pxa2xx_spi_chip {
 	u8 tx_threshold;
 	u8 rx_threshold;
 	u8 dma_burst_size;
-	u32 timeout_microsecs;
+	u32 timeout;
 	u8 enable_loopback;
 	void (*cs_control)(u32 command);
 };
@@ -121,7 +121,7 @@ the PXA2xx "Developer Manual" sections on the DMA controller and SSP Controllers
 to determine the correct value. An SSP configured for byte-wide transfers would
 use a value of 8.
 
-The "pxa2xx_spi_chip.timeout_microsecs" fields is used to efficiently handle
+The "pxa2xx_spi_chip.timeout" fields is used to efficiently handle
 trailing bytes in the SSP receiver fifo.  The correct value for this field is
 dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific
 slave device.  Please note that the PXA2xx SSP 1 does not support trailing byte
@@ -162,18 +162,18 @@ static void cs8405a_cs_control(u32 command)
 }
 
 static struct pxa2xx_spi_chip cs8415a_chip_info = {
-	.tx_threshold = 12, /* SSP hardward FIFO threshold */
-	.rx_threshold = 4, /* SSP hardward FIFO threshold */
+	.tx_threshold = 8, /* SSP hardward FIFO threshold */
+	.rx_threshold = 8, /* SSP hardward FIFO threshold */
 	.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
-	.timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */
+	.timeout = 235, /* See Intel documentation */
 	.cs_control = cs8415a_cs_control, /* Use external chip select */
 };
 
 static struct pxa2xx_spi_chip cs8405a_chip_info = {
-	.tx_threshold = 12, /* SSP hardward FIFO threshold */
-	.rx_threshold = 4, /* SSP hardward FIFO threshold */
+	.tx_threshold = 8, /* SSP hardward FIFO threshold */
+	.rx_threshold = 8, /* SSP hardward FIFO threshold */
 	.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
-	.timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */
+	.timeout = 235, /* See Intel documentation */
 	.cs_control = cs8405a_cs_control, /* Use external chip select */
 };