Merge commit '85082fd7cbe3173198aac0eb5e85ab1edcc6352c' into test-build

Manual fixup of:

	arch/powerpc/Kconfig

1 files changed, 900 insertions, 0 deletions

diff --git a/Documentation/x86/i386/boot.txt b/Documentation/x86/i386/boot.txt
new file mode 100644
index 00000000000..147bfe511cd
--- /dev/null
+++ b/Documentation/x86/i386/boot.txt
@@ -0,0 +1,900 @@
+		     THE LINUX/x86 BOOT PROTOCOL
+		     ---------------------------
+
+On the x86 platform, the Linux kernel uses a rather complicated boot
+convention.  This has evolved partially due to historical aspects, as
+well as the desire in the early days to have the kernel itself be a
+bootable image, the complicated PC memory model and due to changed
+expectations in the PC industry caused by the effective demise of
+real-mode DOS as a mainstream operating system.
+
+Currently, the following versions of the Linux/x86 boot protocol exist.
+
+Old kernels:	zImage/Image support only.  Some very early kernels
+		may not even support a command line.
+
+Protocol 2.00:	(Kernel 1.3.73) Added bzImage and initrd support, as
+		well as a formalized way to communicate between the
+		boot loader and the kernel.  setup.S made relocatable,
+		although the traditional setup area still assumed
+		writable.
+
+Protocol 2.01:	(Kernel 1.3.76) Added a heap overrun warning.
+
+Protocol 2.02:	(Kernel 2.4.0-test3-pre3) New command line protocol.
+		Lower the conventional memory ceiling.	No overwrite
+		of the traditional setup area, thus making booting
+		safe for systems which use the EBDA from SMM or 32-bit
+		BIOS entry points.  zImage deprecated but still
+		supported.
+
+Protocol 2.03:	(Kernel 2.4.18-pre1) Explicitly makes the highest possible
+		initrd address available to the bootloader.
+
+Protocol 2.04:	(Kernel 2.6.14) Extend the syssize field to four bytes.
+
+Protocol 2.05:	(Kernel 2.6.20) Make protected mode kernel relocatable.
+		Introduce relocatable_kernel and kernel_alignment fields.
+
+Protocol 2.06:	(Kernel 2.6.22) Added a field that contains the size of
+		the boot command line.
+
+Protocol 2.07:	(Kernel 2.6.24) Added paravirtualised boot protocol.
+		Introduced hardware_subarch and hardware_subarch_data
+		and KEEP_SEGMENTS flag in load_flags.
+
+Protocol 2.08:	(Kernel 2.6.26) Added crc32 checksum and ELF format
+		payload. Introduced payload_offset and payload length
+		fields to aid in locating the payload.
+
+Protocol 2.09:	(Kernel 2.6.26) Added a field of 64-bit physical
+		pointer to single linked list of struct	setup_data.
+
+**** MEMORY LAYOUT
+
+The traditional memory map for the kernel loader, used for Image or
+zImage kernels, typically looks like:
+
+	|			 |
+0A0000	+------------------------+
+	|  Reserved for BIOS	 |	Do not use.  Reserved for BIOS EBDA.
+09A000	+------------------------+
+	|  Command line		 |
+	|  Stack/heap		 |	For use by the kernel real-mode code.
+098000	+------------------------+	
+	|  Kernel setup		 |	The kernel real-mode code.
+090200	+------------------------+
+	|  Kernel boot sector	 |	The kernel legacy boot sector.
+090000	+------------------------+
+	|  Protected-mode kernel |	The bulk of the kernel image.
+010000	+------------------------+
+	|  Boot loader		 |	<- Boot sector entry point 0000:7C00
+001000	+------------------------+
+	|  Reserved for MBR/BIOS |
+000800	+------------------------+
+	|  Typically used by MBR |
+000600	+------------------------+ 
+	|  BIOS use only	 |
+000000	+------------------------+
+
+
+When using bzImage, the protected-mode kernel was relocated to
+0x100000 ("high memory"), and the kernel real-mode block (boot sector,
+setup, and stack/heap) was made relocatable to any address between
+0x10000 and end of low memory. Unfortunately, in protocols 2.00 and
+2.01 the 0x90000+ memory range is still used internally by the kernel;
+the 2.02 protocol resolves that problem.
+
+It is desirable to keep the "memory ceiling" -- the highest point in
+low memory touched by the boot loader -- as low as possible, since
+some newer BIOSes have begun to allocate some rather large amounts of
+memory, called the Extended BIOS Data Area, near the top of low
+memory.	 The boot loader should use the "INT 12h" BIOS call to verify
+how much low memory is available.
+
+Unfortunately, if INT 12h reports that the amount of memory is too
+low, there is usually nothing the boot loader can do but to report an
+error to the user.  The boot loader should therefore be designed to
+take up as little space in low memory as it reasonably can.  For
+zImage or old bzImage kernels, which need data written into the
+0x90000 segment, the boot loader should make sure not to use memory
+above the 0x9A000 point; too many BIOSes will break above that point.
+
+For a modern bzImage kernel with boot protocol version >= 2.02, a
+memory layout like the following is suggested:
+
+	~                        ~
+        |  Protected-mode kernel |
+100000  +------------------------+
+	|  I/O memory hole	 |
+0A0000	+------------------------+
+	|  Reserved for BIOS	 |	Leave as much as possible unused
+	~                        ~
+	|  Command line		 |	(Can also be below the X+10000 mark)
+X+10000	+------------------------+
+	|  Stack/heap		 |	For use by the kernel real-mode code.
+X+08000	+------------------------+	
+	|  Kernel setup		 |	The kernel real-mode code.
+	|  Kernel boot sector	 |	The kernel legacy boot sector.
+X       +------------------------+
+	|  Boot loader		 |	<- Boot sector entry point 0000:7C00
+001000	+------------------------+
+	|  Reserved for MBR/BIOS |
+000800	+------------------------+
+	|  Typically used by MBR |
+000600	+------------------------+ 
+	|  BIOS use only	 |
+000000	+------------------------+
+
+... where the address X is as low as the design of the boot loader
+permits.
+
+
+**** THE REAL-MODE KERNEL HEADER
+
+In the following text, and anywhere in the kernel boot sequence, "a
+sector" refers to 512 bytes.  It is independent of the actual sector
+size of the underlying medium.
+
+The first step in loading a Linux kernel should be to load the
+real-mode code (boot sector and setup code) and then examine the
+following header at offset 0x01f1.  The real-mode code can total up to
+32K, although the boot loader may choose to load only the first two
+sectors (1K) and then examine the bootup sector size.
+
+The header looks like:
+
+Offset	Proto	Name		Meaning
+/Size
+
+01F1/1	ALL(1	setup_sects	The size of the setup in sectors
+01F2/2	ALL	root_flags	If set, the root is mounted readonly
+01F4/4	2.04+(2	syssize		The size of the 32-bit code in 16-byte paras
+01F8/2	ALL	ram_size	DO NOT USE - for bootsect.S use only
+01FA/2	ALL	vid_mode	Video mode control
+01FC/2	ALL	root_dev	Default root device number
+01FE/2	ALL	boot_flag	0xAA55 magic number
+0200/2	2.00+	jump		Jump instruction
+0202/4	2.00+	header		Magic signature "HdrS"
+0206/2	2.00+	version		Boot protocol version supported
+0208/4	2.00+	realmode_swtch	Boot loader hook (see below)
+020C/2	2.00+	start_sys	The load-low segment (0x1000) (obsolete)
+020E/2	2.00+	kernel_version	Pointer to kernel version string
+0210/1	2.00+	type_of_loader	Boot loader identifier
+0211/1	2.00+	loadflags	Boot protocol option flags
+0212/2	2.00+	setup_move_size	Move to high memory size (used with hooks)
+0214/4	2.00+	code32_start	Boot loader hook (see below)
+0218/4	2.00+	ramdisk_image	initrd load address (set by boot loader)
+021C/4	2.00+	ramdisk_size	initrd size (set by boot loader)
+0220/4	2.00+	bootsect_kludge	DO NOT USE - for bootsect.S use only
+0224/2	2.01+	heap_end_ptr	Free memory after setup end
+0226/2	N/A	pad1		Unused
+0228/4	2.02+	cmd_line_ptr	32-bit pointer to the kernel command line
+022C/4	2.03+	initrd_addr_max	Highest legal initrd address
+0230/4	2.05+	kernel_alignment Physical addr alignment required for kernel
+0234/1	2.05+	relocatable_kernel Whether kernel is relocatable or not
+0235/3	N/A	pad2		Unused
+0238/4	2.06+	cmdline_size	Maximum size of the kernel command line
+023C/4	2.07+	hardware_subarch Hardware subarchitecture
+0240/8	2.07+	hardware_subarch_data Subarchitecture-specific data
+0248/4	2.08+	payload_offset	Offset of kernel payload
+024C/4	2.08+	payload_length	Length of kernel payload
+0250/8	2.09+	setup_data	64-bit physical pointer to linked list
+				of struct setup_data
+
+(1) For backwards compatibility, if the setup_sects field contains 0, the
+    real value is 4.
+
+(2) For boot protocol prior to 2.04, the upper two bytes of the syssize
+    field are unusable, which means the size of a bzImage kernel
+    cannot be determined.
+
+If the "HdrS" (0x53726448) magic number is not found at offset 0x202,
+the boot protocol version is "old".  Loading an old kernel, the
+following parameters should be assumed:
+
+	Image type = zImage
+	initrd not supported
+	Real-mode kernel must be located at 0x90000.
+
+Otherwise, the "version" field contains the protocol version,
+e.g. protocol version 2.01 will contain 0x0201 in this field.  When
+setting fields in the header, you must make sure only to set fields
+supported by the protocol version in use.
+
+
+**** DETAILS OF HEADER FIELDS
+
+For each field, some are information from the kernel to the bootloader
+("read"), some are expected to be filled out by the bootloader
+("write"), and some are expected to be read and modified by the
+bootloader ("modify").
+
+All general purpose boot loaders should write the fields marked
+(obligatory).  Boot loaders who want to load the kernel at a
+nonstandard address should fill in the fields marked (reloc); other
+boot loaders can ignore those fields.
+
+The byte order of all fields is littleendian (this is x86, after all.)
+
+Field name:	setup_sects
+Type:		read
+Offset/size:	0x1f1/1
+Protocol:	ALL
+
+  The size of the setup code in 512-byte sectors.  If this field is
+  0, the real value is 4.  The real-mode code consists of the boot
+  sector (always one 512-byte sector) plus the setup code.
+
+Field name:	 root_flags
+Type:		 modify (optional)
+Offset/size:	 0x1f2/2
+Protocol:	 ALL
+
+  If this field is nonzero, the root defaults to readonly.  The use of
+  this field is deprecated; use the "ro" or "rw" options on the
+  command line instead.
+
+Field name:	syssize
+Type:		read
+Offset/size:	0x1f4/4 (protocol 2.04+) 0x1f4/2 (protocol ALL)
+Protocol:	2.04+
+
+  The size of the protected-mode code in units of 16-byte paragraphs.
+  For protocol versions older than 2.04 this field is only two bytes
+  wide, and therefore cannot be trusted for the size of a kernel if
+  the LOAD_HIGH flag is set.
+
+Field name:	ram_size
+Type:		kernel internal
+Offset/size:	0x1f8/2
+Protocol:	ALL
+
+  This field is obsolete.
+
+Field name:	vid_mode
+Type:		modify (obligatory)
+Offset/size:	0x1fa/2
+
+  Please see the section on SPECIAL COMMAND LINE OPTIONS.
+
+Field name:	root_dev
+Type:		modify (optional)
+Offset/size:	0x1fc/2
+Protocol:	ALL
+
+  The default root device device number.  The use of this field is
+  deprecated, use the "root=" option on the command line instead.
+
+Field name:	boot_flag
+Type:		read
+Offset/size:	0x1fe/2
+Protocol:	ALL
+
+  Contains 0xAA55.  This is the closest thing old Linux kernels have
+  to a magic number.
+
+Field name:	jump
+Type:		read
+Offset/size:	0x200/2
+Protocol:	2.00+
+
+  Contains an x86 jump instruction, 0xEB followed by a signed offset
+  relative to byte 0x202.  This can be used to determine the size of
+  the header.
+
+Field name:	header
+Type:		read
+Offset/size:	0x202/4
+Protocol:	2.00+
+
+  Contains the magic number "HdrS" (0x53726448).
+
+Field name:	version
+Type:		read
+Offset/size:	0x206/2
+Protocol:	2.00+
+
+  Contains the boot protocol version, in (major << 8)+minor format,
+  e.g. 0x0204 for version 2.04, and 0x0a11 for a hypothetical version
+  10.17.
+
+Field name:	readmode_swtch
+Type:		modify (optional)
+Offset/size:	0x208/4
+Protocol:	2.00+
+
+  Boot loader hook (see ADVANCED BOOT LOADER HOOKS below.)
+
+Field name:	start_sys
+Type:		read
+Offset/size:	0x20c/4
+Protocol:	2.00+
+
+  The load low segment (0x1000).  Obsolete.
+
+Field name:	kernel_version
+Type:		read
+Offset/size:	0x20e/2
+Protocol:	2.00+
+
+  If set to a nonzero value, contains a pointer to a NUL-terminated
+  human-readable kernel version number string, less 0x200.  This can
+  be used to display the kernel version to the user.  This value
+  should be less than (0x200*setup_sects).
+
+  For example, if this value is set to 0x1c00, the kernel version
+  number string can be found at offset 0x1e00 in the kernel file.
+  This is a valid value if and only if the "setup_sects" field
+  contains the value 15 or higher, as:
+
+	0x1c00  < 15*0x200 (= 0x1e00) but
+	0x1c00 >= 14*0x200 (= 0x1c00)
+
+	0x1c00 >> 9 = 14, so the minimum value for setup_secs is 15.
+
+Field name:	type_of_loader
+Type:		write (obligatory)
+Offset/size:	0x210/1
+Protocol:	2.00+
+
+  If your boot loader has an assigned id (see table below), enter
+  0xTV here, where T is an identifier for the boot loader and V is
+  a version number.  Otherwise, enter 0xFF here.
+
+  Assigned boot loader ids:
+	0  LILO			(0x00 reserved for pre-2.00 bootloader)
+	1  Loadlin
+	2  bootsect-loader	(0x20, all other values reserved)
+	3  SYSLINUX
+	4  EtherBoot
+	5  ELILO
+	7  GRuB
+	8  U-BOOT
+	9  Xen
+	A  Gujin
+	B  Qemu
+
+  Please contact <hpa@zytor.com> if you need a bootloader ID
+  value assigned.
+
+Field name:	loadflags
+Type:		modify (obligatory)
+Offset/size:	0x211/1
+Protocol:	2.00+
+
+  This field is a bitmask.
+
+  Bit 0 (read):	LOADED_HIGH
+	- If 0, the protected-mode code is loaded at 0x10000.
+	- If 1, the protected-mode code is loaded at 0x100000.
+
+  Bit 5 (write): QUIET_FLAG
+	- If 0, print early messages.
+	- If 1, suppress early messages.
+		This requests to the kernel (decompressor and early
+		kernel) to not write early messages that require
+		accessing the display hardware directly.
+
+  Bit 6 (write): KEEP_SEGMENTS
+	Protocol: 2.07+
+	- If 0, reload the segment registers in the 32bit entry point.
+	- If 1, do not reload the segment registers in the 32bit entry point.
+		Assume that %cs %ds %ss %es are all set to flat segments with
+		a base of 0 (or the equivalent for their environment).
+
+  Bit 7 (write): CAN_USE_HEAP
+	Set this bit to 1 to indicate that the value entered in the
+	heap_end_ptr is valid.  If this field is clear, some setup code
+	functionality will be disabled.
+
+Field name:	setup_move_size
+Type:		modify (obligatory)
+Offset/size:	0x212/2
+Protocol:	2.00-2.01
+
+  When using protocol 2.00 or 2.01, if the real mode kernel is not
+  loaded at 0x90000, it gets moved there later in the loading
+  sequence.  Fill in this field if you want additional data (such as
+  the kernel command line) moved in addition to the real-mode kernel
+  itself.
+
+  The unit is bytes starting with the beginning of the boot sector.
+  
+  This field is can be ignored when the protocol is 2.02 or higher, or
+  if the real-mode code is loaded at 0x90000.
+
+Field name:	code32_start
+Type:		modify (optional, reloc)
+Offset/size:	0x214/4
+Protocol:	2.00+
+
+  The address to jump to in protected mode.  This defaults to the load
+  address of the kernel, and can be used by the boot loader to
+  determine the proper load address.
+
+  This field can be modified for two purposes:
+
+  1. as a boot loader hook (see ADVANCED BOOT LOADER HOOKS below.)
+
+  2. if a bootloader which does not install a hook loads a
+     relocatable kernel at a nonstandard address it will have to modify
+     this field to point to the load address.
+
+Field name:	ramdisk_image
+Type:		write (obligatory)
+Offset/size:	0x218/4
+Protocol:	2.00+
+
+  The 32-bit linear address of the initial ramdisk or ramfs.  Leave at
+  zero if there is no initial ramdisk/ramfs.
+
+Field name:	ramdisk_size
+Type:		write (obligatory)
+Offset/size:	0x21c/4
+Protocol:	2.00+
+
+  Size of the initial ramdisk or ramfs.  Leave at zero if there is no
+  initial ramdisk/ramfs.
+
+Field name:	bootsect_kludge
+Type:		kernel internal
+Offset/size:	0x220/4
+Protocol:	2.00+
+
+  This field is obsolete.
+
+Field name:	heap_end_ptr
+Type:		write (obligatory)
+Offset/size:	0x224/2
+Protocol:	2.01+
+
+  Set this field to the offset (from the beginning of the real-mode
+  code) of the end of the setup stack/heap, minus 0x0200.
+
+Field name:	cmd_line_ptr
+Type:		write (obligatory)
+Offset/size:	0x228/4
+Protocol:	2.02+
+
+  Set this field to the linear address of the kernel command line.
+  The kernel command line can be located anywhere between the end of
+  the setup heap and 0xA0000; it does not have to be located in the
+  same 64K segment as the real-mode code itself.
+
+  Fill in this field even if your boot loader does not support a
+  command line, in which case you can point this to an empty string
+  (or better yet, to the string "auto".)  If this field is left at
+  zero, the kernel will assume that your boot loader does not support
+  the 2.02+ protocol.
+
+Field name:	initrd_addr_max
+Type:		read
+Offset/size:	0x22c/4
+Protocol:	2.03+
+
+  The maximum address that may be occupied by the initial
+  ramdisk/ramfs contents.  For boot protocols 2.02 or earlier, this
+  field is not present, and the maximum address is 0x37FFFFFF.  (This
+  address is defined as the address of the highest safe byte, so if
+  your ramdisk is exactly 131072 bytes long and this field is
+  0x37FFFFFF, you can start your ramdisk at 0x37FE0000.)
+
+Field name:	kernel_alignment
+Type:		read (reloc)
+Offset/size:	0x230/4
+Protocol:	2.05+
+
+  Alignment unit required by the kernel (if relocatable_kernel is true.)
+
+Field name:	relocatable_kernel
+Type:		read (reloc)
+Offset/size:	0x234/1
+Protocol:	2.05+
+
+  If this field is nonzero, the protected-mode part of the kernel can
+  be loaded at any address that satisfies the kernel_alignment field.
+  After loading, the boot loader must set the code32_start field to
+  point to the loaded code, or to a boot loader hook.
+
+Field name:	cmdline_size
+Type:		read
+Offset/size:	0x238/4
+Protocol:	2.06+
+
+  The maximum size of the command line without the terminating
+  zero. This means that the command line can contain at most
+  cmdline_size characters. With protocol version 2.05 and earlier, the
+  maximum size was 255.
+
+Field name:	hardware_subarch
+Type:		write (optional, defaults to x86/PC)
+Offset/size:	0x23c/4
+Protocol:	2.07+
+
+  In a paravirtualized environment the hardware low level architectural
+  pieces such as interrupt handling, page table handling, and
+  accessing process control registers needs to be done differently.
+
+  This field allows the bootloader to inform the kernel we are in one
+  one of those environments.
+
+  0x00000000	The default x86/PC environment
+  0x00000001	lguest
+  0x00000002	Xen
+
+Field name:	hardware_subarch_data
+Type:		write (subarch-dependent)
+Offset/size:	0x240/8
+Protocol:	2.07+
+
+  A pointer to data that is specific to hardware subarch
+  This field is currently unused for the default x86/PC environment,
+  do not modify.
+
+Field name:	payload_offset
+Type:		read
+Offset/size:	0x248/4
+Protocol:	2.08+
+
+  If non-zero then this field contains the offset from the end of the
+  real-mode code to the payload.
+
+  The payload may be compressed. The format of both the compressed and
+  uncompressed data should be determined using the standard magic
+  numbers. Currently only gzip compressed ELF is used.
+  
+Field name:	payload_length
+Type:		read
+Offset/size:	0x24c/4
+Protocol:	2.08+
+
+  The length of the payload.
+
+Field name:	setup_data
+Type:		write (special)
+Offset/size:	0x250/8
+Protocol:	2.09+
+
+  The 64-bit physical pointer to NULL terminated single linked list of
+  struct setup_data. This is used to define a more extensible boot
+  parameters passing mechanism. The definition of struct setup_data is
+  as follow:
+
+  struct setup_data {
+	  u64 next;
+	  u32 type;
+	  u32 len;
+	  u8  data[0];
+  };
+
+  Where, the next is a 64-bit physical pointer to the next node of
+  linked list, the next field of the last node is 0; the type is used
+  to identify the contents of data; the len is the length of data
+  field; the data holds the real payload.
+
+  This list may be modified at a number of points during the bootup
+  process.  Therefore, when modifying this list one should always make
+  sure to consider the case where the linked list already contains
+  entries.
+
+
+**** THE IMAGE CHECKSUM
+
+From boot protocol version 2.08 onwards the CRC-32 is calculated over
+the entire file using the characteristic polynomial 0x04C11DB7 and an
+initial remainder of 0xffffffff.  The checksum is appended to the
+file; therefore the CRC of the file up to the limit specified in the
+syssize field of the header is always 0.
+
+
+**** THE KERNEL COMMAND LINE
+
+The kernel command line has become an important way for the boot
+loader to communicate with the kernel.  Some of its options are also
+relevant to the boot loader itself, see "special command line options"
+below.
+
+The kernel command line is a null-terminated string. The maximum
+length can be retrieved from the field cmdline_size.  Before protocol
+version 2.06, the maximum was 255 characters.  A string that is too
+long will be automatically truncated by the kernel.
+
+If the boot protocol version is 2.02 or later, the address of the
+kernel command line is given by the header field cmd_line_ptr (see
+above.)  This address can be anywhere between the end of the setup
+heap and 0xA0000.
+
+If the protocol version is *not* 2.02 or higher, the kernel
+command line is entered using the following protocol:
+
+	At offset 0x0020 (word), "cmd_line_magic", enter the magic
+	number 0xA33F.
+
+	At offset 0x0022 (word), "cmd_line_offset", enter the offset
+	of the kernel command line (relative to the start of the
+	real-mode kernel).
+	
+	The kernel command line *must* be within the memory region
+	covered by setup_move_size, so you may need to adjust this
+	field.
+
+
+**** MEMORY LAYOUT OF THE REAL-MODE CODE
+
+The real-mode code requires a stack/heap to be set up, as well as
+memory allocated for the kernel command line.  This needs to be done
+in the real-mode accessible memory in bottom megabyte.
+
+It should be noted that modern machines often have a sizable Extended
+BIOS Data Area (EBDA).  As a result, it is advisable to use as little
+of the low megabyte as possible.
+
+Unfortunately, under the following circumstances the 0x90000 memory
+segment has to be used:
+
+	- When loading a zImage kernel ((loadflags & 0x01) == 0).
+	- When loading a 2.01 or earlier boot protocol kernel.
+
+	  -> For the 2.00 and 2.01 boot protocols, the real-mode code
+	     can be loaded at another address, but it is internally
+	     relocated to 0x90000.  For the "old" protocol, the
+	     real-mode code must be loaded at 0x90000.
+
+When loading at 0x90000, avoid using memory above 0x9a000.
+
+For boot protocol 2.02 or higher, the command line does not have to be
+located in the same 64K segment as the real-mode setup code; it is
+thus permitted to give the stack/heap the full 64K segment and locate
+the command line above it.
+
+The kernel command line should not be located below the real-mode
+code, nor should it be located in high memory.
+
+
+**** SAMPLE BOOT CONFIGURATION
+
+As a sample configuration, assume the following layout of the real
+mode segment:
+
+    When loading below 0x90000, use the entire segment:
+
+	0x0000-0x7fff	Real mode kernel
+	0x8000-0xdfff	Stack and heap
+	0xe000-0xffff	Kernel command line
+
+    When loading at 0x90000 OR the protocol version is 2.01 or earlier:
+
+	0x0000-0x7fff	Real mode kernel
+	0x8000-0x97ff	Stack and heap
+	0x9800-0x9fff	Kernel command line
+
+Such a boot loader should enter the following fields in the header:
+
+	unsigned long base_ptr;	/* base address for real-mode segment */
+
+	if ( setup_sects == 0 ) {
+		setup_sects = 4;
+	}
+
+	if ( protocol >= 0x0200 ) {
+		type_of_loader = <type code>;
+		if ( loading_initrd ) {
+			ramdisk_image = <initrd_address>;
+			ramdisk_size = <initrd_size>;
+		}
+
+		if ( protocol >= 0x0202 && loadflags & 0x01 )
+			heap_end = 0xe000;
+		else
+			heap_end = 0x9800;
+
+		if ( protocol >= 0x0201 ) {
+			heap_end_ptr = heap_end - 0x200;
+			loadflags |= 0x80; /* CAN_USE_HEAP */
+		}
+
+		if ( protocol >= 0x0202 ) {
+			cmd_line_ptr = base_ptr + heap_end;
+			strcpy(cmd_line_ptr, cmdline);
+		} else {
+			cmd_line_magic	= 0xA33F;
+			cmd_line_offset = heap_end;
+			setup_move_size = heap_end + strlen(cmdline)+1;
+			strcpy(base_ptr+cmd_line_offset, cmdline);
+		}
+	} else {
+		/* Very old kernel */
+
+		heap_end = 0x9800;
+
+		cmd_line_magic	= 0xA33F;
+		cmd_line_offset = heap_end;
+
+		/* A very old kernel MUST have its real-mode code
+		   loaded at 0x90000 */
+
+		if ( base_ptr != 0x90000 ) {
+			/* Copy the real-mode kernel */
+			memcpy(0x90000, base_ptr, (setup_sects+1)*512);
+			base_ptr = 0x90000;		 /* Relocated */
+		}
+
+		strcpy(0x90000+cmd_line_offset, cmdline);
+
+		/* It is recommended to clear memory up to the 32K mark */
+		memset(0x90000 + (setup_sects+1)*512, 0,
+		       (64-(setup_sects+1))*512);
+	}
+
+
+**** LOADING THE REST OF THE KERNEL
+
+The 32-bit (non-real-mode) kernel starts at offset (setup_sects+1)*512
+in the kernel file (again, if setup_sects == 0 the real value is 4.)
+It should be loaded at address 0x10000 for Image/zImage kernels and
+0x100000 for bzImage kernels.
+
+The kernel is a bzImage kernel if the protocol >= 2.00 and the 0x01
+bit (LOAD_HIGH) in the loadflags field is set:
+
+	is_bzImage = (protocol >= 0x0200) && (loadflags & 0x01);
+	load_address = is_bzImage ? 0x100000 : 0x10000;
+
+Note that Image/zImage kernels can be up to 512K in size, and thus use
+the entire 0x10000-0x90000 range of memory.  This means it is pretty
+much a requirement for these kernels to load the real-mode part at
+0x90000.  bzImage kernels allow much more flexibility.
+
+
+**** SPECIAL COMMAND LINE OPTIONS
+
+If the command line provided by the boot loader is entered by the
+user, the user may expect the following command line options to work.
+They should normally not be deleted from the kernel command line even
+though not all of them are actually meaningful to the kernel.  Boot
+loader authors who need additional command line options for the boot
+loader itself should get them registered in
+Documentation/kernel-parameters.txt to make sure they will not
+conflict with actual kernel options now or in the future.
+
+  vga=<mode>
+	<mode> here is either an integer (in C notation, either
+	decimal, octal, or hexadecimal) or one of the strings
+	"normal" (meaning 0xFFFF), "ext" (meaning 0xFFFE) or "ask"
+	(meaning 0xFFFD).  This value should be entered into the
+	vid_mode field, as it is used by the kernel before the command
+	line is parsed.
+
+  mem=<size>
+	<size> is an integer in C notation optionally followed by
+	(case insensitive) K, M, G, T, P or E (meaning << 10, << 20,
+	<< 30, << 40, << 50 or << 60).  This specifies the end of
+	memory to the kernel. This affects the possible placement of
+	an initrd, since an initrd should be placed near end of
+	memory.  Note that this is an option to *both* the kernel and
+	the bootloader!
+
+  initrd=<file>
+	An initrd should be loaded.  The meaning of <file> is
+	obviously bootloader-dependent, and some boot loaders
+	(e.g. LILO) do not have such a command.
+
+In addition, some boot loaders add the following options to the
+user-specified command line:
+
+  BOOT_IMAGE=<file>
+	The boot image which was loaded.  Again, the meaning of <file>
+	is obviously bootloader-dependent.
+
+  auto
+	The kernel was booted without explicit user intervention.
+
+If these options are added by the boot loader, it is highly
+recommended that they are located *first*, before the user-specified
+or configuration-specified command line.  Otherwise, "init=/bin/sh"
+gets confused by the "auto" option.
+
+
+**** RUNNING THE KERNEL
+
+The kernel is started by jumping to the kernel entry point, which is
+located at *segment* offset 0x20 from the start of the real mode
+kernel.  This means that if you loaded your real-mode kernel code at
+0x90000, the kernel entry point is 9020:0000.
+
+At entry, ds = es = ss should point to the start of the real-mode
+kernel code (0x9000 if the code is loaded at 0x90000), sp should be
+set up properly, normally pointing to the top of the heap, and
+interrupts should be disabled.  Furthermore, to guard against bugs in
+the kernel, it is recommended that the boot loader sets fs = gs = ds =
+es = ss.
+
+In our example from above, we would do:
+
+	/* Note: in the case of the "old" kernel protocol, base_ptr must
+	   be == 0x90000 at this point; see the previous sample code */
+
+	seg = base_ptr >> 4;
+
+	cli();	/* Enter with interrupts disabled! */
+
+	/* Set up the real-mode kernel stack */
+	_SS = seg;
+	_SP = heap_end;
+
+	_DS = _ES = _FS = _GS = seg;
+	jmp_far(seg+0x20, 0);	/* Run the kernel */
+
+If your boot sector accesses a floppy drive, it is recommended to
+switch off the floppy motor before running the kernel, since the
+kernel boot leaves interrupts off and thus the motor will not be
+switched off, especially if the loaded kernel has the floppy driver as
+a demand-loaded module!
+
+
+**** ADVANCED BOOT LOADER HOOKS
+
+If the boot loader runs in a particularly hostile environment (such as
+LOADLIN, which runs under DOS) it may be impossible to follow the
+standard memory location requirements.  Such a boot loader may use the
+following hooks that, if set, are invoked by the kernel at the
+appropriate time.  The use of these hooks should probably be
+considered an absolutely last resort!
+
+IMPORTANT: All the hooks are required to preserve %esp, %ebp, %esi and
+%edi across invocation.
+
+  realmode_swtch:
+	A 16-bit real mode far subroutine invoked immediately before
+	entering protected mode.  The default routine disables NMI, so
+	your routine should probably do so, too.
+
+  code32_start:
+	A 32-bit flat-mode routine *jumped* to immediately after the
+	transition to protected mode, but before the kernel is
+	uncompressed.  No segments, except CS, are guaranteed to be
+	set up (current kernels do, but older ones do not); you should
+	set them up to BOOT_DS (0x18) yourself.
+
+	After completing your hook, you should jump to the address
+	that was in this field before your boot loader overwrote it
+	(relocated, if appropriate.)
+
+
+**** 32-bit BOOT PROTOCOL
+
+For machine with some new BIOS other than legacy BIOS, such as EFI,
+LinuxBIOS, etc, and kexec, the 16-bit real mode setup code in kernel
+based on legacy BIOS can not be used, so a 32-bit boot protocol needs
+to be defined.
+
+In 32-bit boot protocol, the first step in loading a Linux kernel
+should be to setup the boot parameters (struct boot_params,
+traditionally known as "zero page"). The memory for struct boot_params
+should be allocated and initialized to all zero. Then the setup header
+from offset 0x01f1 of kernel image on should be loaded into struct
+boot_params and examined. The end of setup header can be calculated as
+follow:
+
+	0x0202 + byte value at offset 0x0201
+
+In addition to read/modify/write the setup header of the struct
+boot_params as that of 16-bit boot protocol, the boot loader should
+also fill the additional fields of the struct boot_params as that
+described in zero-page.txt.
+
+After setupping the struct boot_params, the boot loader can load the
+32/64-bit kernel in the same way as that of 16-bit boot protocol.
+
+In 32-bit boot protocol, the kernel is started by jumping to the
+32-bit kernel entry point, which is the start address of loaded
+32/64-bit kernel.
+
+At entry, the CPU must be in 32-bit protected mode with paging
+disabled; a GDT must be loaded with the descriptors for selectors
+__BOOT_CS(0x10) and __BOOT_DS(0x18); both descriptors must be 4G flat
+segment; __BOOS_CS must have execute/read permission, and __BOOT_DS
+must have read/write permission; CS must be __BOOT_CS and DS, ES, SS
+must be __BOOT_DS; interrupt must be disabled; %esi must hold the base
+address of the struct boot_params; %ebp, %edi and %ebx must be zero.