Merge tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging driver updates from Greg KH:
 "Here's the huge drivers/staging/ update for 3.15-rc1.

  Loads of cleanup fixes, a few drivers removed, and some new ones
  added.

  All have been in linux-next for a while"

* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
  staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
  staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
  staging: comedi: poc: remove obsolete driver
  staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
  staging: octeon-usb: prevent memory corruption
  staging: usbip: fix line over 80 characters
  staging: usbip: fix quoted string split across lines
  Staging: unisys: Remove RETINT macro
  Staging: unisys: Remove FAIL macro
  Staging: unisys: Remove RETVOID macro
  Staging: unisys: Remove RETPTR macro
  Staging: unisys: Remove RETBOOL macro
  Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
  Staging: unisys: Cleanup macros to get rid of goto statements
  Staging: unisys: include: Remove unused macros from timskmod.h
  staging: dgap: fix the rest of the checkpatch warnings in dgap.c
  Staging: bcm: Remove unnecessary parentheses
  staging: wlags49_h2: Delete unnecessary braces
  staging: wlags49_h2: Do not use assignment in if condition
  staging: wlags49_h2: Enclose macro in a do-while loop
  ...

7 files changed, 386 insertions, 9 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt
index d1061469f63..9a1175b46f4 100644
--- a/Documentation/devicetree/bindings/arm/atmel-adc.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt
@@ -5,6 +5,9 @@ Required properties:
     <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
   - reg: Should contain ADC registers location and length
   - interrupts: Should contain the IRQ line for the ADC
+  - clock-names: tuple listing input clock names.
+	Required elements: "adc_clk", "adc_op_clk".
+  - clocks: phandles to input clocks.
   - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
     device
   - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
@@ -44,6 +47,8 @@ adc0: adc@fffb0000 {
 	compatible = "atmel,at91sam9260-adc";
 	reg = <0xfffb0000 0x100>;
 	interrupts = <20 4>;
+	clocks = <&adc_clk>, <&adc_op_clk>;
+	clock-names = "adc_clk", "adc_op_clk";
 	atmel,adc-channel-base = <0x30>;
 	atmel,adc-channels-used = <0xff>;
 	atmel,adc-drdy-mask = <0x10000>;
diff --git a/Documentation/devicetree/bindings/graph.txt b/Documentation/devicetree/bindings/graph.txt
new file mode 100644
index 00000000000..1a69c078adf
--- /dev/null
+++ b/Documentation/devicetree/bindings/graph.txt
@@ -0,0 +1,129 @@
+Common bindings for device graphs
+
+General concept
+---------------
+
+The hierarchical organisation of the device tree is well suited to describe
+control flow to devices, but there can be more complex connections between
+devices that work together to form a logical compound device, following an
+arbitrarily complex graph.
+There already is a simple directed graph between devices tree nodes using
+phandle properties pointing to other nodes to describe connections that
+can not be inferred from device tree parent-child relationships. The device
+tree graph bindings described herein abstract more complex devices that can
+have multiple specifiable ports, each of which can be linked to one or more
+ports of other devices.
+
+These common bindings do not contain any information about the direction or
+type of the connections, they just map their existence. Specific properties
+may be described by specialized bindings depending on the type of connection.
+
+To see how this binding applies to video pipelines, for example, see
+Documentation/device-tree/bindings/media/video-interfaces.txt.
+Here the ports describe data interfaces, and the links between them are
+the connecting data buses. A single port with multiple connections can
+correspond to multiple devices being connected to the same physical bus.
+
+Organisation of ports and endpoints
+-----------------------------------
+
+Ports are described by child 'port' nodes contained in the device node.
+Each port node contains an 'endpoint' subnode for each remote device port
+connected to this port. If a single port is connected to more than one
+remote device, an 'endpoint' child node must be provided for each link.
+If more than one port is present in a device node or there is more than one
+endpoint at a port, or a port node needs to be associated with a selected
+hardware interface, a common scheme using '#address-cells', '#size-cells'
+and 'reg' properties is used number the nodes.
+
+device {
+        ...
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        port@0 {
+	        #address-cells = <1>;
+	        #size-cells = <0>;
+		reg = <0>;
+
+                endpoint@0 {
+			reg = <0>;
+			...
+		};
+                endpoint@1 {
+			reg = <1>;
+			...
+		};
+        };
+
+        port@1 {
+		reg = <1>;
+
+		endpoint { ... };
+	};
+};
+
+All 'port' nodes can be grouped under an optional 'ports' node, which
+allows to specify #address-cells, #size-cells properties for the 'port'
+nodes independently from any other child device nodes a device might
+have.
+
+device {
+        ...
+        ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                        ...
+                        endpoint@0 { ... };
+                        endpoint@1 { ... };
+                };
+
+                port@1 { ... };
+        };
+};
+
+Links between endpoints
+-----------------------
+
+Each endpoint should contain a 'remote-endpoint' phandle property that points
+to the corresponding endpoint in the port of the remote device. In turn, the
+remote endpoint should contain a 'remote-endpoint' property. If it has one,
+it must not point to another than the local endpoint. Two endpoints with their
+'remote-endpoint' phandles pointing at each other form a link between the
+containing ports.
+
+device-1 {
+        port {
+                device_1_output: endpoint {
+                        remote-endpoint = <&device_2_input>;
+                };
+        };
+};
+
+device-2 {
+        port {
+                device_2_input: endpoint {
+                        remote-endpoint = <&device_1_output>;
+                };
+        };
+};
+
+
+Required properties
+-------------------
+
+If there is more than one 'port' or more than one 'endpoint' node or 'reg'
+property is present in port and/or endpoint nodes the following properties
+are required in a relevant parent node:
+
+ - #address-cells : number of cells required to define port/endpoint
+                    identifier, should be 1.
+ - #size-cells    : should be zero.
+
+Optional endpoint properties
+----------------------------
+
+- remote-endpoint: phandle to an 'endpoint' subnode of a remote device node.
+
diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
new file mode 100644
index 00000000000..dcebff1928e
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
@@ -0,0 +1,22 @@
+Freescale vf610 Analog to Digital Converter bindings
+
+The devicetree bindings are for the new ADC driver written for
+vf610/i.MX6slx and upward SoCs from Freescale.
+
+Required properties:
+- compatible: Should contain "fsl,vf610-adc"
+- reg: Offset and length of the register set for the device
+- interrupts: Should contain the interrupt for the device
+- clocks: The clock is needed by the ADC controller, ADC clock source is ipg clock.
+- clock-names: Must contain "adc", matching entry in the clocks property.
+- vref-supply: The regulator supply ADC refrence voltage.
+
+Example:
+adc0: adc@4003b000 {
+	compatible = "fsl,vf610-adc";
+	reg = <0x4003b000 0x1000>;
+	interrupts = <0 53 0x04>;
+	clocks = <&clks VF610_CLK_ADC0>;
+	clock-names = "adc";
+	vref-supply = <&reg_vcc_3v3_mcu>;
+};
diff --git a/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt
new file mode 100644
index 00000000000..d9ee909d2b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/xilinx-xadc.txt
@@ -0,0 +1,113 @@
+Xilinx XADC device driver
+
+This binding document describes the bindings for both of them since the
+bindings are very similar. The Xilinx XADC is a ADC that can be found in the
+series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication.
+Currently two different frontends for the DRP interface exist. One that is only
+available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The
+other one is available on all series 7 platforms and is a softmacro with a AXI
+interface. This binding document describes the bindings for both of them since
+the bindings are very similar.
+
+Required properties:
+	- compatible: Should be one of
+		* "xlnx,zynq-xadc-1.00.a": When using the ZYNQ device
+		  configuration interface to interface to the XADC hardmacro.
+		* "xlnx,axi-xadc-1.00.a": When using the axi-xadc pcore to
+		  interface to the XADC hardmacro.
+	- reg: Address and length of the register set for the device
+	- interrupts: Interrupt for the XADC control interface.
+	- clocks: When using the ZYNQ this must be the ZYNQ PCAP clock,
+	  when using the AXI-XADC pcore this must be the clock that provides the
+	  clock to the AXI bus interface of the core.
+
+Optional properties:
+	- interrupt-parent: phandle to the parent interrupt controller
+	- xlnx,external-mux:
+		* "none": No external multiplexer is used, this is the default
+		  if the property is omitted.
+		* "single": External multiplexer mode is used with one
+		   multiplexer.
+		* "dual": External multiplexer mode is used with two
+		  multiplexers for simultaneous sampling.
+	- xlnx,external-mux-channel: Configures which pair of pins is used to
+	  sample data in external mux mode.
+	  Valid values for single external multiplexer mode are:
+		0: VP/VN
+		1: VAUXP[0]/VAUXN[0]
+		2: VAUXP[1]/VAUXN[1]
+		...
+		16: VAUXP[15]/VAUXN[15]
+	  Valid values for dual external multiplexer mode are:
+		1: VAUXP[0]/VAUXN[0] - VAUXP[8]/VAUXN[8]
+		2: VAUXP[1]/VAUXN[1] - VAUXP[9]/VAUXN[9]
+		...
+		8: VAUXP[7]/VAUXN[7] - VAUXP[15]/VAUXN[15]
+
+	  This property needs to be present if the device is configured for
+	  external multiplexer mode (either single or dual). If the device is
+	  not using external multiplexer mode the property is ignored.
+	- xnlx,channels: List of external channels that are connected to the ADC
+	  Required properties:
+		* #address-cells: Should be 1.
+		* #size-cells: Should be 0.
+
+	  The child nodes of this node represent the external channels which are
+	  connected to the ADC. If the property is no present no external
+	  channels will be assumed to be connected.
+
+	  Each child node represents one channel and has the following
+	  properties:
+		Required properties:
+			* reg: Pair of pins the the channel is connected to.
+				0: VP/VN
+				1: VAUXP[0]/VAUXN[0]
+				2: VAUXP[1]/VAUXN[1]
+				...
+				16: VAUXP[15]/VAUXN[15]
+			  Note each channel number should only be used at most
+			  once.
+		Optional properties:
+			* xlnx,bipolar: If set the channel is used in bipolar
+			  mode.
+
+
+Examples:
+	xadc@f8007100 {
+		compatible = "xlnx,zynq-xadc-1.00.a";
+		reg = <0xf8007100 0x20>;
+		interrupts = <0 7 4>;
+		interrupt-parent = <&gic>;
+		clocks = <&pcap_clk>;
+
+		xlnx,channels {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			channel@0 {
+				reg = <0>;
+			};
+			channel@1 {
+				reg = <1>;
+			};
+			channel@8 {
+				reg = <8>;
+			};
+		};
+	};
+
+	xadc@43200000 {
+		compatible = "xlnx,axi-xadc-1.00.a";
+		reg = <0x43200000 0x1000>;
+		interrupts = <0 53 4>;
+		interrupt-parent = <&gic>;
+		clocks = <&fpga1_clk>;
+
+		xlnx,channels {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			channel@0 {
+				reg = <0>;
+				xlnx,bipolar;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt
index b876d4925a5..3be5ce7a965 100644
--- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt
+++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt
@@ -1,3 +1,22 @@
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface ports
+  of IPU devices
+
+example:
+
+display-subsystem {
+	compatible = "fsl,display-subsystem";
+	ports = <&ipu_di0>;
+};
+
+
 Freescale i.MX IPUv3
 ====================
 
@@ -7,18 +26,31 @@ Required properties:
   datasheet
 - interrupts: Should contain sync interrupt and error interrupt,
   in this order.
-- #crtc-cells: 1, See below
 - resets: phandle pointing to the system reset controller and
           reset line index, see reset/fsl,imx-src.txt for details
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Ports 0 and 1 should correspond to CSI0 and CSI1,
+  ports 2 and 3 should correspond to DI0 and DI1, respectively.
 
 example:
 
 ipu: ipu@18000000 {
-	#crtc-cells = <1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
 	compatible = "fsl,imx53-ipu";
 	reg = <0x18000000 0x080000000>;
 	interrupts = <11 10>;
 	resets = <&src 2>;
+
+	ipu_di0: port@2 {
+		reg = <2>;
+
+		ipu_di0_disp0: endpoint {
+			remote-endpoint = <&display_in>;
+		};
+	};
 };
 
 Parallel display support
@@ -26,19 +58,25 @@ Parallel display support
 
 Required properties:
 - compatible: Should be "fsl,imx-parallel-display"
-- crtc: the crtc this display is connected to, see below
 Optional properties:
 - interface_pix_fmt: How this display is connected to the
-  crtc. Currently supported types: "rgb24", "rgb565", "bgr666"
+  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
 - edid: verbatim EDID data block describing attached display.
 - ddc: phandle describing the i2c bus handling the display data
   channel
+- port: A port node with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
 
 example:
 
 display@di0 {
 	compatible = "fsl,imx-parallel-display";
 	edid = [edid-data];
-	crtc = <&ipu 0>;
 	interface-pix-fmt = "rgb24";
+
+	port {
+		display_in: endpoint {
+			remote-endpoint = <&ipu_di0_disp0>;
+		};
+	};
 };
diff --git a/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt b/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt
new file mode 100644
index 00000000000..1b756cf9afb
--- /dev/null
+++ b/Documentation/devicetree/bindings/staging/imx-drm/hdmi.txt
@@ -0,0 +1,58 @@
+Device-Tree bindings for HDMI Transmitter
+
+HDMI Transmitter
+================
+
+The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with accompanying PHY IP.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
+ - gpr : should be <&gpr>.
+   The phandle points to the iomuxc-gpr region containing the HDMI
+   multiplexer control register.
+ - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described
+   in Documentation/devicetree/bindings/clock/clock-bindings.txt and
+   Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+ - port@[0-4]: Up to four port nodes with endpoint definitions as defined in
+   Documentation/devicetree/bindings/media/video-interfaces.txt,
+   corresponding to the four inputs to the HDMI multiplexer.
+
+Optional properties:
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+
+example:
+
+	gpr: iomuxc-gpr@020e0000 {
+		/* ... */
+	};
+
+        hdmi: hdmi@0120000 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                compatible = "fsl,imx6q-hdmi";
+                reg = <0x00120000 0x9000>;
+                interrupts = <0 115 0x04>;
+                gpr = <&gpr>;
+                clocks = <&clks 123>, <&clks 124>;
+                clock-names = "iahb", "isfr";
+                ddc-i2c-bus = <&i2c2>;
+
+                port@0 {
+                        reg = <0>;
+
+                        hdmi_mux_0: endpoint {
+                                remote-endpoint = <&ipu1_di0_hdmi>;
+                        };
+                };
+
+                port@1 {
+                        reg = <1>;
+
+                        hdmi_mux_1: endpoint {
+                                remote-endpoint = <&ipu1_di1_hdmi>;
+                        };
+                };
+        };
diff --git a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt
index ed9377811ee..578a1fca366 100644
--- a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt
+++ b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt
@@ -50,12 +50,14 @@ have a look at Documentation/devicetree/bindings/video/display-timing.txt.
 
 Required properties:
  - reg : should be <0> or <1>
- - crtcs : a list of phandles with index pointing to the IPU display interfaces
-           that can be used as video source for this channel.
  - fsl,data-mapping : should be "spwg" or "jeida"
                       This describes how the color bits are laid out in the
                       serialized LVDS signal.
  - fsl,data-width : should be <18> or <24>
+ - port: A port node with endpoint definitions as defined in
+   Documentation/devicetree/bindings/media/video-interfaces.txt.
+   On i.MX6, there should be four ports (port@[0-3]) that correspond
+   to the four LVDS multiplexer inputs.
 
 example:
 
@@ -77,23 +79,33 @@ ldb: ldb@53fa8008 {
 
 	lvds-channel@0 {
 		reg = <0>;
-		crtcs = <&ipu 0>;
 		fsl,data-mapping = "spwg";
 		fsl,data-width = <24>;
 
 		display-timings {
 			/* ... */
 		};
+
+		port {
+			lvds0_in: endpoint {
+				remote-endpoint = <&ipu_di0_lvds0>;
+			};
+		};
 	};
 
 	lvds-channel@1 {
 		reg = <1>;
-		crtcs = <&ipu 1>;
 		fsl,data-mapping = "spwg";
 		fsl,data-width = <24>;
 
 		display-timings {
 			/* ... */
 		};
+
+		port {
+			lvds1_in: endpoint {
+				remote-endpoint = <&ipu_di1_lvds1>;
+			};
+		};
 	};
 };