Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
  x86: Clean up apic.c and apic.h
  x86: Remove superflous goal definition of tsc_sync
  x86: dt: Correct local apic documentation in device tree bindings
  x86: dt: Cleanup local apic setup
  x86: dt: Fix OLPC=y/INTEL_CE=n build
  rtc: cmos: Add OF bindings
  x86: ce4100: Use OF to setup devices
  x86: ioapic: Add OF bindings for IO_APIC
  x86: dtb: Add generic bus probe
  x86: dtb: Add support for PCI devices backed by dtb nodes
  x86: dtb: Add device tree support for HPET
  x86: dtb: Add early parsing of IO_APIC
  x86: dtb: Add irq domain abstraction
  x86: dtb: Add a device tree for CE4100
  x86: Add device tree support
  x86: e820: Remove conditional early mapping in parse_e820_ext
  x86: OLPC: Make OLPC=n build again
  x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
  x86: OLPC: Cleanup config maze completely
  x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
  ...

Fix up conflicts in arch/x86/platform/ce4100/ce4100.c

6 files changed, 211 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt b/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt
new file mode 100644
index 00000000000..569b1624851
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt
@@ -0,0 +1,93 @@
+CE4100 I2C
+----------
+
+CE4100 has one PCI device which is described as the I2C-Controller. This
+PCI device has three PCI-bars, each bar contains a complete I2C
+controller. So we have a total of three independent I2C-Controllers
+which share only an interrupt line.
+The driver is probed via the PCI-ID and is gathering the information of
+attached devices from the devices tree.
+Grant Likely recommended to use the ranges property to map the PCI-Bar
+number to its physical address and to use this to find the child nodes
+of the specific I2C controller. This were his exact words:
+
+       Here's where the magic happens.  Each entry in
+       ranges describes how the parent pci address space
+       (middle group of 3) is translated to the local
+       address space (first group of 2) and the size of
+       each range (last cell).  In this particular case,
+       the first cell of the local address is chosen to be
+       1:1 mapped to the BARs, and the second is the
+       offset from be base of the BAR (which would be
+       non-zero if you had 2 or more devices mapped off
+       the same BAR)
+
+       ranges allows the address mapping to be described
+       in a way that the OS can interpret without
+       requiring custom device driver code.
+
+This is an example which is used on FalconFalls:
+------------------------------------------------
+	i2c-controller@b,2 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "pci8086,2e68.2",
+				"pci8086,2e68",
+				"pciclass,ff0000",
+				"pciclass,ff00";
+
+		reg = <0x15a00 0x0 0x0 0x0 0x0>;
+		interrupts = <16 1>;
+
+		/* as described by Grant, the first number in the group of
+		* three is the bar number followed by the 64bit bar address
+		* followed by size of the mapping. The bar address
+		* requires also a valid translation in parents ranges
+		* property.
+		*/
+		ranges = <0 0   0x02000000 0 0xdffe0500 0x100
+			  1 0   0x02000000 0 0xdffe0600 0x100
+			  2 0   0x02000000 0 0xdffe0700 0x100>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+
+			/* The first number in the reg property is the
+			* number of the bar
+			*/
+			reg = <0 0 0x100>;
+
+			/* This I2C controller has no devices */
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+			reg = <1 0 0x100>;
+
+			/* This I2C controller has one gpio controller */
+			gpio@26 {
+				#gpio-cells = <2>;
+				compatible = "ti,pcf8575";
+				reg = <0x26>;
+				gpio-controller;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+			reg = <2 0 0x100>;
+
+			gpio@26 {
+				#gpio-cells = <2>;
+				compatible = "ti,pcf8575";
+				reg = <0x26>;
+				gpio-controller;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/rtc/rtc-cmos.txt b/Documentation/devicetree/bindings/rtc/rtc-cmos.txt
new file mode 100644
index 00000000000..7382989b305
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc-cmos.txt
@@ -0,0 +1,28 @@
+ Motorola mc146818 compatible RTC
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Required properties:
+  - compatible : "motorola,mc146818"
+  - reg : should contain registers location and length.
+
+Optional properties:
+  - interrupts : should contain interrupt.
+  - interrupt-parent : interrupt source phandle.
+  - ctrl-reg : Contains the initial value of the control register also
+    called "Register B".
+  - freq-reg : Contains the initial value of the frequency register also
+    called "Regsiter A".
+
+"Register A" and "B" are usually initialized by the firmware (BIOS for
+instance). If this is not done, it can be performed by the driver.
+
+ISA Example:
+
+	rtc@70 {
+	         compatible = "motorola,mc146818";
+	         interrupts = <8 3>;
+	         interrupt-parent = <&ioapic1>;
+	         ctrl-reg = <2>;
+	         freq-reg = <0x26>;
+	         reg = <1 0x70 2>;
+	 };
diff --git a/Documentation/devicetree/bindings/x86/ce4100.txt b/Documentation/devicetree/bindings/x86/ce4100.txt
new file mode 100644
index 00000000000..b49ae593a60
--- /dev/null
+++ b/Documentation/devicetree/bindings/x86/ce4100.txt
@@ -0,0 +1,38 @@
+CE4100 Device Tree Bindings
+---------------------------
+
+The CE4100 SoC uses for in core peripherals the following compatible
+format: <vendor>,<chip>-<device>.
+Many of the "generic" devices like HPET or IO APIC have the ce4100
+name in their compatible property because they first appeared in this
+SoC.
+
+The CPU node
+------------
+	cpu@0 {
+		device_type = "cpu";
+		compatible = "intel,ce4100";
+		reg = <0>;
+		lapic = <&lapic0>;
+	};
+
+The reg property describes the CPU number. The lapic property points to
+the local APIC timer.
+
+The SoC node
+------------
+
+This node describes the in-core peripherals. Required property:
+  compatible = "intel,ce4100-cp";
+
+The PCI node
+------------
+This node describes the PCI bus on the SoC. Its property should be
+  compatible = "intel,ce4100-pci", "pci";
+
+If the OS is using the IO-APIC for interrupt routing then the reported
+interrupt numbers for devices is no longer true. In order to obtain the
+correct interrupt number, the child node which represents the device has
+to contain the interrupt property. Besides the interrupt property it has
+to contain at least the reg property containing the PCI bus address and
+compatible property according to "PCI Bus Binding Revision 2.1".
diff --git a/Documentation/devicetree/bindings/x86/interrupt.txt b/Documentation/devicetree/bindings/x86/interrupt.txt
new file mode 100644
index 00000000000..7d19f494f19
--- /dev/null
+++ b/Documentation/devicetree/bindings/x86/interrupt.txt
@@ -0,0 +1,26 @@
+Interrupt chips
+---------------
+
+* Intel I/O Advanced Programmable Interrupt Controller (IO APIC)
+
+  Required properties:
+  --------------------
+     compatible = "intel,ce4100-ioapic";
+     #interrupt-cells = <2>;
+
+  Device's interrupt property:
+
+     interrupts = <P S>;
+
+  The first number (P) represents the interrupt pin which is wired to the
+  IO APIC. The second number (S) represents the sense of interrupt which
+  should be configured and can be one of:
+    0 - Edge Rising
+    1 - Level Low
+    2 - Level High
+    3 - Edge Falling
+
+* Local APIC
+  Required property:
+
+     compatible = "intel,ce4100-lapic";
diff --git a/Documentation/devicetree/bindings/x86/timer.txt b/Documentation/devicetree/bindings/x86/timer.txt
new file mode 100644
index 00000000000..c688af58e3b
--- /dev/null
+++ b/Documentation/devicetree/bindings/x86/timer.txt
@@ -0,0 +1,6 @@
+Timers
+------
+
+* High Precision Event Timer (HPET)
+  Required property:
+     compatible = "intel,ce4100-hpet";
diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt
index 28b1c9d3d35..55fd2623445 100644
--- a/Documentation/devicetree/booting-without-of.txt
+++ b/Documentation/devicetree/booting-without-of.txt
@@ -13,6 +13,7 @@ Table of Contents
 
   I - Introduction
     1) Entry point for arch/powerpc
+    2) Entry point for arch/x86
 
   II - The DT block format
     1) Header
@@ -225,6 +226,25 @@ it with special cases.
   cannot support both configurations with Book E and configurations
   with classic Powerpc architectures.
 
+2) Entry point for arch/x86
+-------------------------------
+
+  There is one single 32bit entry point to the kernel at code32_start,
+  the decompressor (the real mode entry point goes to the same  32bit
+  entry point once it switched into protected mode). That entry point
+  supports one calling convention which is documented in
+  Documentation/x86/boot.txt
+  The physical pointer to the device-tree block (defined in chapter II)
+  is passed via setup_data which requires at least boot protocol 2.09.
+  The type filed is defined as
+
+  #define SETUP_DTB                      2
+
+  This device-tree is used as an extension to the "boot page". As such it
+  does not parse / consider data which is already covered by the boot
+  page. This includes memory size, reserved ranges, command line arguments
+  or initrd address. It simply holds information which can not be retrieved
+  otherwise like interrupt routing or a list of devices behind an I2C bus.
 
 II - The DT block format
 ========================