Merge branch 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "For 3.19, the I2C subsystem has to offer special candy this time.
  Right in time for Christmas :)

   - I2C slave framework: finally, a generic mechanism for Linux being
     an I2C slave (if the bus driver supports that).  Docs are still
     missing but will come later this cycle, the code is good enough to
     go.
   - I2C muxes represent their topology in sysfs much more detailed.
     This will help users to navigate around much easier.
   - irq population of i2c clients is now done at probe time, not device
     creation time, to have better support for deferred probing.
   - new drivers for Imagination SCB, Amlogic Meson
   - DMA support added for Freescale IMX, Renesas SHMobile
   - slightly bigger driver updates to OMAP, i801, AT91, and rk3x
     (mostly quirk handling, timing updates, and using better kernel
     interfaces)
   - eeprom driver can now write with byte-access (very slow, but OK to
     have)
   - and the bunch of smaller fixes, cleanups, ID updates..."

* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
  i2c: sh_mobile: remove unneeded DMA mask
  i2c: rcar: add slave support
  i2c: slave-eeprom: add eeprom simulator driver
  i2c: core changes for slave support
  MAINTAINERS: add I2C dt bindings also to I2C realm
  i2c: designware: Fix falling time bindings doc
  i2c: davinci: switch to use platform_get_irq
  Documentation: i2c: Use PM ops instead of legacy suspend/resume
  i2c: sh_mobile: optimize irq entry
  i2c: pxa: add support for SCCB devices
  omap: i2c: don't check bus state IP rev3.3 and earlier
  i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
  i2c: rk3x: add Kconfig dependency on COMMON_CLK
  i2c: omap: add notes related to i2c multimaster mode
  i2c: omap: don't reset controller if Arbitration Lost detected
  i2c: omap: implement workaround for handling invalid BB-bit values
  i2c: omap: cleanup register definitions
  i2c: rk3x: handle dynamic clock rate changes correctly
  i2c: at91: enable probe deferring on dma channel request
  i2c: at91: remove legacy DMA support
  ...

9 files changed, 92 insertions, 10 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
index 5199b0c8cf7..fee26dc3e85 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
@@ -14,10 +14,10 @@ Optional properties :
  - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds.
    This option is only supported in hardware blocks version 1.11a or newer.
 
- - i2c-scl-falling-time : should contain the SCL falling time in nanoseconds.
+ - i2c-scl-falling-time-ns : should contain the SCL falling time in nanoseconds.
    This value which is by default 300ns is used to compute the tLOW period.
 
- - i2c-sda-falling-time : should contain the SDA falling time in nanoseconds.
+ - i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds.
    This value which is by default 300ns is used to compute the tHIGH period.
 
 Example :
diff --git a/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt
new file mode 100644
index 00000000000..b6461602dca
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt
@@ -0,0 +1,26 @@
+IMG Serial Control Bus (SCB) I2C Controller
+
+Required Properties:
+- compatible: "img,scb-i2c"
+- reg: Physical base address and length of controller registers
+- interrupts: Interrupt number used by the controller
+- clocks : Should contain a clock specifier for each entry in clock-names
+- clock-names : Should contain the following entries:
+                "scb", for the SCB core clock.
+                "sys", for the system clock.
+- clock-frequency: The I2C bus frequency in Hz
+- #address-cells: Should be <1>
+- #size-cells: Should be <0>
+
+Example:
+
+i2c@18100000 {
+	compatible = "img,scb-i2c";
+	reg = <0x18100000 0x200>;
+	interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&i2c0_clk>, <&system_clk>;
+	clock-names = "scb", "sys";
+	clock-frequency = <400000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
index 4a8513e4474..52d37fd8d3e 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
@@ -11,6 +11,8 @@ Required properties:
 Optional properties:
 - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
   The absence of the propoerty indicates the default frequency 100 kHz.
+- dmas: A list of two dma specifiers, one for each entry in dma-names.
+- dma-names: should contain "tx" and "rx".
 
 Examples:
 
@@ -26,3 +28,12 @@ i2c@70038000 { /* HS-I2C on i.MX51 */
 	interrupts = <64>;
 	clock-frequency = <400000>;
 };
+
+i2c0: i2c@40066000 { /* i2c0 on vf610 */
+	compatible = "fsl,vf610-i2c";
+	reg = <0x40066000 0x1000>;
+	interrupts =<0 71 0x04>;
+	dmas = <&edma0 0 50>,
+		<&edma0 0 51>;
+	dma-names = "rx","tx";
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-meson.txt b/Documentation/devicetree/bindings/i2c/i2c-meson.txt
new file mode 100644
index 00000000000..682f9a6f766
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-meson.txt
@@ -0,0 +1,24 @@
+Amlogic Meson I2C controller
+
+Required properties:
+ - compatible: must be "amlogic,meson6-i2c"
+ - reg: physical address and length of the device registers
+ - interrupts: a single interrupt specifier
+ - clocks: clock for the device
+ - #address-cells: should be <1>
+ - #size-cells: should be <0>
+
+Optional properties:
+- clock-frequency: the desired I2C bus clock frequency in Hz; in
+  absence of this property the default value is used (100 kHz).
+
+Examples:
+
+	i2c@c8100500 {
+		compatible = "amlogic,meson6-i2c";
+		reg = <0xc8100500 0x20>;
+		interrupts = <0 92 1>;
+		clocks = <&clk81>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt
index d2153ce36fa..2bfc6e7ed09 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt
@@ -2,6 +2,15 @@ Device tree configuration for Renesas IIC (sh_mobile) driver
 
 Required properties:
 - compatible      : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback
+		     Examples with soctypes are:
+			- "renesas,iic-r8a73a4" (R-Mobile APE6)
+			- "renesas,iic-r8a7740" (R-Mobile A1)
+			- "renesas,iic-r8a7790" (R-Car H2)
+			- "renesas,iic-r8a7791" (R-Car M2-W)
+			- "renesas,iic-r8a7792" (R-Car V2H)
+			- "renesas,iic-r8a7793" (R-Car M2-N)
+			- "renesas,iic-r8a7794" (R-Car E2)
+			- "renesas,iic-sh73a0" (SH-Mobile AG5)
 - reg             : address start and address range size of device
 - interrupts      : interrupt of device
 - clocks          : clock for device
@@ -10,6 +19,11 @@ Required properties:
 
 Optional properties:
 - clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset.
+- dmas            : Must contain a list of two references to DMA
+		    specifiers, one for transmission, and one for
+		    reception.
+- dma-names       : Must contain a list of two DMA names, "tx" and "rx".
+
 
 Pinctrl properties might be needed, too. See there.
 
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 605dcca5dbe..9f4e3824e71 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -17,6 +17,9 @@ adi,adt7473		+/-1C TDM Extended Temp Range I.C
 adi,adt7475		+/-1C TDM Extended Temp Range I.C
 adi,adt7476		+/-1C TDM Extended Temp Range I.C
 adi,adt7490		+/-1C TDM Extended Temp Range I.C
+adi,adxl345		Three-Axis Digital Accelerometer
+adi,adxl346		Three-Axis Digital Accelerometer
+adi,adxl34x		Three-Axis Digital Accelerometer
 at,24c08		i2c serial eeprom  (24cxx)
 atmel,24c00		i2c serial eeprom  (24cxx)
 atmel,24c01		i2c serial eeprom  (24cxx)
@@ -76,7 +79,12 @@ ovti,ov5642		OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI an
 pericom,pt7c4338	Real-time Clock Module
 plx,pex8648		48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch
 ramtron,24c64		i2c serial eeprom  (24cxx)
+ricoh,r2025sd		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,r2221tl		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 ricoh,rs5c372a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,rs5c372b		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,rv5c386		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ricoh,rv5c387a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 samsung,24ad0xd1	S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
 sii,s35390a		2-wire CMOS real-time clock
 st-micro,24c256		i2c serial eeprom  (24cxx)
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index 793c83dac73..82f48f774af 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -29,6 +29,7 @@ Supported adapters:
   * Intel Wildcat Point-LP (PCH)
   * Intel BayTrail (SOC)
   * Intel Sunrise Point-H (PCH)
+  * Intel Sunrise Point-LP (PCH)
    Datasheets: Publicly available at the Intel website
 
 On Intel Patsburg and later chipsets, both the normal host SMBus controller
diff --git a/Documentation/i2c/upgrading-clients b/Documentation/i2c/upgrading-clients
index 8e5fbd88c7d..ccba3ffd6e8 100644
--- a/Documentation/i2c/upgrading-clients
+++ b/Documentation/i2c/upgrading-clients
@@ -79,11 +79,10 @@ static struct i2c_driver example_driver = {
  	.driver		= {
 		.owner		= THIS_MODULE,
 		.name		= "example",
+		.pm		= &example_pm_ops,
 	},
 	.attach_adapter = example_attach_adapter,
 	.detach_client	= example_detach,
-	.suspend	= example_suspend,
-	.resume		= example_resume,
 };
 
 
@@ -272,10 +271,9 @@ static struct i2c_driver example_driver = {
  	.driver		= {
 		.owner		= THIS_MODULE,
 		.name		= "example",
+		.pm		= &example_pm_ops,
 	},
 	.id_table	= example_idtable,
 	.probe		= example_probe,
 	.remove		= example_remove,
-	.suspend	= example_suspend,
-	.resume		= example_resume,
 };
diff --git a/Documentation/i2c/writing-clients b/Documentation/i2c/writing-clients
index 6b344b516bf..a755b141fa4 100644
--- a/Documentation/i2c/writing-clients
+++ b/Documentation/i2c/writing-clients
@@ -36,6 +36,7 @@ MODULE_DEVICE_TABLE(i2c, foo_idtable);
 static struct i2c_driver foo_driver = {
 	.driver = {
 		.name	= "foo",
+		.pm	= &foo_pm_ops,	/* optional */
 	},
 
 	.id_table	= foo_idtable,
@@ -47,8 +48,6 @@ static struct i2c_driver foo_driver = {
 	.address_list	= normal_i2c,
 
 	.shutdown	= foo_shutdown,	/* optional */
-	.suspend	= foo_suspend,	/* optional */
-	.resume		= foo_resume,	/* optional */
 	.command	= foo_command,	/* optional, deprecated */
 }
 
@@ -279,8 +278,9 @@ Power Management
 
 If your I2C device needs special handling when entering a system low
 power state -- like putting a transceiver into a low power mode, or
-activating a system wakeup mechanism -- do that in the suspend() method.
-The resume() method should reverse what the suspend() method does.
+activating a system wakeup mechanism -- do that by implementing the
+appropriate callbacks for the dev_pm_ops of the driver (like suspend
+and resume).
 
 These are standard driver model calls, and they work just like they
 would for any other driver stack.  The calls can sleep, and can use