Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

Pull powerpc updates from Ben Herrenschmidt:
 "This is the powerpc new goodies for 3.17.  The short story:

  The biggest bit is Michael removing all of pre-POWER4 processor
  support from the 64-bit kernel.  POWER3 and rs64.  This gets rid of a
  ton of old cruft that has been bitrotting in a long while.  It was
  broken for quite a few versions already and nobody noticed.  Nobody
  uses those machines anymore.  While at it, he cleaned up a bunch of
  old dusty cabinets, getting rid of a skeletton or two.

  Then, we have some base VFIO support for KVM, which allows assigning
  of PCI devices to KVM guests, support for large 64-bit BARs on
  "powernv" platforms, support for HMI (Hardware Management Interrupts)
  on those same platforms, some sparse-vmemmap improvements (for memory
  hotplug),

  There is the usual batch of Freescale embedded updates (summary in the
  merge commit) and fixes here or there, I think that's it for the
  highlights"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
  powerpc/eeh: Export eeh_iommu_group_to_pe()
  powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
  powerpc: Reduce scariness of interrupt frames in stack traces
  powerpc: start loop at section start of start in vmemmap_populated()
  powerpc: implement vmemmap_free()
  powerpc: implement vmemmap_remove_mapping() for BOOK3S
  powerpc: implement vmemmap_list_free()
  powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
  powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
  powerpc/book3s: handle HMIs for cpus in nap mode.
  powerpc/powernv: Invoke opal call to handle hmi.
  powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
  powerpc/iommu: Fix comments with it_page_shift
  powerpc/powernv: Handle compound PE in config accessors
  powerpc/powernv: Handle compound PE for EEH
  powerpc/powernv: Handle compound PE
  powerpc/powernv: Split ioda_eeh_get_state()
  powerpc/powernv: Allow to freeze PE
  powerpc/powernv: Enable M64 aperatus for PHB3
  powerpc/eeh: Aux PE data for error log
  ...

2 files changed, 100 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt
index 700dec4774f..cff38bdbc0e 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/board.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt
@@ -84,3 +84,19 @@ Example:
 		compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c";
 		reg = <0x66>;
 	};
+
+* Freescale on-board CPLD
+
+Some Freescale boards like T1040RDB have an on board CPLD connected.
+
+Required properties:
+- compatible: Should be a board-specific string like "fsl,<board>-cpld"
+  Example:
+	"fsl,t1040rdb-cpld", "fsl,t1042rdb-cpld", "fsl,t1042rdb_pi-cpld"
+- reg: should describe CPLD registers
+
+Example:
+	cpld@3,0 {
+		compatible = "fsl,t1040rdb-cpld";
+		reg = <3 0 0x300>;
+	};
diff --git a/Documentation/vfio.txt b/Documentation/vfio.txt
index b9ca02370d4..96978eced34 100644
--- a/Documentation/vfio.txt
+++ b/Documentation/vfio.txt
@@ -305,7 +305,15 @@ faster, the map/unmap handling has been implemented in real mode which provides
 an excellent performance which has limitations such as inability to do
 locked pages accounting in real time.
 
-So 3 additional ioctls have been added:
+4) According to sPAPR specification, A Partitionable Endpoint (PE) is an I/O
+subtree that can be treated as a unit for the purposes of partitioning and
+error recovery. A PE may be a single or multi-function IOA (IO Adapter), a
+function of a multi-function IOA, or multiple IOAs (possibly including switch
+and bridge structures above the multiple IOAs). PPC64 guests detect PCI errors
+and recover from them via EEH RTAS services, which works on the basis of
+additional ioctl commands.
+
+So 4 additional ioctls have been added:
 
 	VFIO_IOMMU_SPAPR_TCE_GET_INFO - returns the size and the start
 		of the DMA window on the PCI bus.
@@ -316,9 +324,12 @@ So 3 additional ioctls have been added:
 
 	VFIO_IOMMU_DISABLE - disables the container.
 
+	VFIO_EEH_PE_OP - provides an API for EEH setup, error detection and recovery.
 
 The code flow from the example above should be slightly changed:
 
+	struct vfio_eeh_pe_op pe_op = { .argsz = sizeof(pe_op), .flags = 0 };
+
 	.....
 	/* Add the group to the container */
 	ioctl(group, VFIO_GROUP_SET_CONTAINER, &container);
@@ -342,9 +353,79 @@ The code flow from the example above should be slightly changed:
 	dma_map.flags = VFIO_DMA_MAP_FLAG_READ | VFIO_DMA_MAP_FLAG_WRITE;
 
 	/* Check here is .iova/.size are within DMA window from spapr_iommu_info */
-
 	ioctl(container, VFIO_IOMMU_MAP_DMA, &dma_map);
-	.....
+
+	/* Get a file descriptor for the device */
+	device = ioctl(group, VFIO_GROUP_GET_DEVICE_FD, "0000:06:0d.0");
+
+	....
+
+	/* Gratuitous device reset and go... */
+	ioctl(device, VFIO_DEVICE_RESET);
+
+	/* Make sure EEH is supported */
+	ioctl(container, VFIO_CHECK_EXTENSION, VFIO_EEH);
+
+	/* Enable the EEH functionality on the device */
+	pe_op.op = VFIO_EEH_PE_ENABLE;
+	ioctl(container, VFIO_EEH_PE_OP, &pe_op);
+
+	/* You're suggested to create additional data struct to represent
+	 * PE, and put child devices belonging to same IOMMU group to the
+	 * PE instance for later reference.
+	 */
+
+	/* Check the PE's state and make sure it's in functional state */
+	pe_op.op = VFIO_EEH_PE_GET_STATE;
+	ioctl(container, VFIO_EEH_PE_OP, &pe_op);
+
+	/* Save device state using pci_save_state().
+	 * EEH should be enabled on the specified device.
+	 */
+
+	....
+
+	/* When 0xFF's returned from reading PCI config space or IO BARs
+	 * of the PCI device. Check the PE's state to see if that has been
+	 * frozen.
+	 */
+	ioctl(container, VFIO_EEH_PE_OP, &pe_op);
+
+	/* Waiting for pending PCI transactions to be completed and don't
+	 * produce any more PCI traffic from/to the affected PE until
+	 * recovery is finished.
+	 */
+
+	/* Enable IO for the affected PE and collect logs. Usually, the
+	 * standard part of PCI config space, AER registers are dumped
+	 * as logs for further analysis.
+	 */
+	pe_op.op = VFIO_EEH_PE_UNFREEZE_IO;
+	ioctl(container, VFIO_EEH_PE_OP, &pe_op);
+
+	/*
+	 * Issue PE reset: hot or fundamental reset. Usually, hot reset
+	 * is enough. However, the firmware of some PCI adapters would
+	 * require fundamental reset.
+	 */
+	pe_op.op = VFIO_EEH_PE_RESET_HOT;
+	ioctl(container, VFIO_EEH_PE_OP, &pe_op);
+	pe_op.op = VFIO_EEH_PE_RESET_DEACTIVATE;
+	ioctl(container, VFIO_EEH_PE_OP, &pe_op);
+
+	/* Configure the PCI bridges for the affected PE */
+	pe_op.op = VFIO_EEH_PE_CONFIGURE;
+	ioctl(container, VFIO_EEH_PE_OP, &pe_op);
+
+	/* Restored state we saved at initialization time. pci_restore_state()
+	 * is good enough as an example.
+	 */
+
+	/* Hopefully, error is recovered successfully. Now, you can resume to
+	 * start PCI traffic to/from the affected PE.
+	 */
+
+	....
 
 -------------------------------------------------------------------------------