Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
  leds: Futher document blink_set
  leds: Add options to have GPIO LEDs start on or keep their state
  leds: LED driver for National Semiconductor LP3944 Funlight Chip
  leds: pca9532 - Indent using tabs, not spaces.
  leds: Remove an orphan Kconfig entry
  leds: Further document parameters for blink_set()
  leds: alix-leds2 fixed for Award BIOS
  leds: leds-gpio - fix a section mismatch
  leds: add the sysfs interface into the leds-bd2802 driver for changing wave pattern and led current.
  leds: change the license information
  leds: fix led-bd2802 errors while resuming

2 files changed, 66 insertions, 1 deletions

diff --git a/Documentation/leds-lp3944.txt b/Documentation/leds-lp3944.txt
new file mode 100644
index 00000000000..c6eda18b15e
--- /dev/null
+++ b/Documentation/leds-lp3944.txt
@@ -0,0 +1,50 @@
+Kernel driver lp3944
+====================
+
+  * National Semiconductor LP3944 Fun-light Chip
+    Prefix: 'lp3944'
+    Addresses scanned: None (see the Notes section below)
+    Datasheet: Publicly available at the National Semiconductor website
+               http://www.national.com/pf/LP/LP3944.html
+
+Authors:
+        Antonio Ospite <ospite@studenti.unina.it>
+
+
+Description
+-----------
+The LP3944 is a helper chip that can drive up to 8 leds, with two programmable
+DIM modes; it could even be used as a gpio expander but this driver assumes it
+is used as a led controller.
+
+The DIM modes are used to set _blink_ patterns for leds, the pattern is
+specified supplying two parameters:
+  - period: from 0s to 1.6s
+  - duty cycle: percentage of the period the led is on, from 0 to 100
+
+Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
+See the datasheet for details.
+
+LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
+leds, the camera flash light and the lcds power.
+
+
+Notes
+-----
+The chip is used mainly in embedded contexts, so this driver expects it is
+registered using the i2c_board_info mechanism.
+
+To register the chip at address 0x60 on adapter 0, set the platform data
+according to include/linux/leds-lp3944.h, set the i2c board info:
+
+	static struct i2c_board_info __initdata a910_i2c_board_info[] = {
+		{
+			I2C_BOARD_INFO("lp3944", 0x60),
+			.platform_data = &a910_lp3944_leds,
+		},
+	};
+
+and register it in the platform init function
+
+	i2c_register_board_info(0, a910_i2c_board_info,
+			ARRAY_SIZE(a910_i2c_board_info));
diff --git a/Documentation/powerpc/dts-bindings/gpio/led.txt b/Documentation/powerpc/dts-bindings/gpio/led.txt
index 4fe14deedc0..064db928c3c 100644
--- a/Documentation/powerpc/dts-bindings/gpio/led.txt
+++ b/Documentation/powerpc/dts-bindings/gpio/led.txt
@@ -16,10 +16,17 @@ LED sub-node properties:
   string defining the trigger assigned to the LED.  Current triggers are:
     "backlight" - LED will act as a back-light, controlled by the framebuffer
 		  system
-    "default-on" - LED will turn on
+    "default-on" - LED will turn on, but see "default-state" below
     "heartbeat" - LED "double" flashes at a load average based rate
     "ide-disk" - LED indicates disk activity
     "timer" - LED flashes at a fixed, configurable rate
+- default-state:  (optional) The initial state of the LED.  Valid
+  values are "on", "off", and "keep".  If the LED is already on or off
+  and the default-state property is set the to same value, then no
+  glitch should be produced where the LED momentarily turns off (or
+  on).  The "keep" setting will keep the LED at whatever its current
+  state is, without producing a glitch.  The default is off if this
+  property is not present.
 
 Examples:
 
@@ -30,14 +37,22 @@ leds {
 		gpios = <&mcu_pio 0 1>; /* Active low */
 		linux,default-trigger = "ide-disk";
 	};
+
+	fault {
+		gpios = <&mcu_pio 1 0>;
+		/* Keep LED on if BIOS detected hardware fault */
+		default-state = "keep";
+	};
 };
 
 run-control {
 	compatible = "gpio-leds";
 	red {
 		gpios = <&mpc8572 6 0>;
+		default-state = "off";
 	};
 	green {
 		gpios = <&mpc8572 7 0>;
+		default-state = "on";
 	};
 }