Merge branch 'writeback-workqueue' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq into for-3.10/core

Tejun writes:

-----

This is the pull request for the earlier patchset[1] with the same
name.  It's only three patches (the first one was committed to
workqueue tree) but the merge strategy is a bit involved due to the
dependencies.

* Because the conversion needs features from wq/for-3.10,
  block/for-3.10/core is based on rc3, and wq/for-3.10 has conflicts
  with rc3, I pulled mainline (rc5) into wq/for-3.10 to prevent those
  workqueue conflicts from flaring up in block tree.

* Resolving the issue that Jan and Dave raised about debugging
  requires arch-wide changes.  The patchset is being worked on[2] but
  it'll have to go through -mm after these changes show up in -next,
  and not included in this pull request.

The three commits are located in the following git branch.

  git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git writeback-workqueue

Pulling it into block/for-3.10/core produces a conflict in
drivers/md/raid5.c between the following two commits.

  e3620a3ad5 ("MD RAID5: Avoid accessing gendisk or queue structs when not available")
  2f6db2a707 ("raid5: use bio_reset()")

The conflict is trivial - one removes an "if ()" conditional while the
other removes "rbi->bi_next = NULL" right above it.  We just need to
remove both.  The merged branch is available at

  git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git block-test-merge

so that you can use it for verification.  The test merge commit has
proper merge description.

While these changes are a bit of pain to route, they make code simpler
and even have, while minute, measureable performance gain[3] even on a
workload which isn't particularly favorable to showing the benefits of
this conversion.

----

Fixed up the conflict.

Conflicts:
	drivers/md/raid5.c

Signed-off-by: Jens Axboe <axboe@kernel.dk>

6 files changed, 20 insertions, 4 deletions

diff --git a/Documentation/hwmon/lm75 b/Documentation/hwmon/lm75
index c91a1d15fa2..69af1c7db6b 100644
--- a/Documentation/hwmon/lm75
+++ b/Documentation/hwmon/lm75
@@ -23,7 +23,7 @@ Supported chips:
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/
   * Microchip (TelCom) TCN75
-    Prefix: 'lm75'
+    Prefix: 'tcn75'
     Addresses scanned: none
     Datasheet: Publicly available at the Microchip website
                http://www.microchip.com/
diff --git a/Documentation/i2c/busses/i2c-diolan-u2c b/Documentation/i2c/busses/i2c-diolan-u2c
index 30fe4bb9a06..0d6018c316c 100644
--- a/Documentation/i2c/busses/i2c-diolan-u2c
+++ b/Documentation/i2c/busses/i2c-diolan-u2c
@@ -5,7 +5,7 @@ Supported adapters:
     Documentation:
 	http://www.diolan.com/i2c/u2c12.html
 
-Author: Guenter Roeck <guenter.roeck@ericsson.com>
+Author: Guenter Roeck <linux@roeck-us.net>
 
 Description
 -----------
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 4609e81dbc3..c75ea0b8ec5 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -3222,6 +3222,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			or other driver-specific files in the
 			Documentation/watchdog/ directory.
 
+	workqueue.disable_numa
+			By default, all work items queued to unbound
+			workqueues are affine to the NUMA nodes they're
+			issued on, which results in better behavior in
+			general.  If NUMA affinity needs to be disabled for
+			whatever reason, this option can be used.  Note
+			that this also can be controlled per-workqueue for
+			workqueues visible under /sys/bus/workqueue/.
+
 	x2apic_phys	[X86-64,APIC] Use x2apic physical mode instead of
 			default x2apic cluster mode on platforms
 			supporting x2apic.
diff --git a/Documentation/networking/ipvs-sysctl.txt b/Documentation/networking/ipvs-sysctl.txt
index f2a2488f1bf..9573d0c48c6 100644
--- a/Documentation/networking/ipvs-sysctl.txt
+++ b/Documentation/networking/ipvs-sysctl.txt
@@ -15,6 +15,13 @@ amemthresh - INTEGER
         enabled and the variable is automatically set to 2, otherwise
         the strategy is disabled and the variable is  set  to 1.
 
+backup_only - BOOLEAN
+	0 - disabled (default)
+	not 0 - enabled
+
+	If set, disable the director function while the server is
+	in backup mode to avoid packet loops for DR/TUN methods.
+
 conntrack - BOOLEAN
 	0 - disabled (default)
 	not 0 - enabled
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt
index ce6581c8ca2..4499bd94886 100644
--- a/Documentation/sound/alsa/ALSA-Configuration.txt
+++ b/Documentation/sound/alsa/ALSA-Configuration.txt
@@ -912,7 +912,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
     models depending on the codec chip.  The list of available models
     is found in HD-Audio-Models.txt
 
-    The model name "genric" is treated as a special case.  When this
+    The model name "generic" is treated as a special case.  When this
     model is given, the driver uses the generic codec parser without
     "codec-patch".  It's sometimes good for testing and debugging.
 
diff --git a/Documentation/sound/alsa/seq_oss.html b/Documentation/sound/alsa/seq_oss.html
index d9776cf60c0..9663b45f6fd 100644
--- a/Documentation/sound/alsa/seq_oss.html
+++ b/Documentation/sound/alsa/seq_oss.html
@@ -285,7 +285,7 @@ sample data.
 <H4>
 7.2.4 Close Callback</H4>
 The <TT>close</TT> callback is called when this device is closed by the
-applicaion. If any private data was allocated in open callback, it must
+application. If any private data was allocated in open callback, it must
 be released in the close callback. The deletion of ALSA port should be
 done here, too. This callback must not be NULL.
 <H4>