Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Olof Johansson:
 "Most of this branch consists of updates, additions and general churn
  of the device tree source files in the kernel (arch/arm/boot/dts).
  Besides that, there are a few things to point out:

   - Lots of platform conversion on OMAP2+, with removal of old board
     files for various platforms.
   - Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
     well
   - Some updates to pinctrl and other subsystems.  Most of these are
     for DT-enablement of the various platforms and acks have been
     collected"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
  ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
  ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
  ARM: dts: bcm281xx: Add card detect GPIO
  ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
  ARM: bcm281xx: Add device node for the GPIO controller
  ARM: mvebu: Add Netgear ReadyNAS 104 board
  ARM: tegra: fix Tegra114 IOMMU register address
  ARM: kirkwood: add support for OpenBlocks A7 platform
  ARM: dts: omap4-panda: add DPI pinmuxing
  ARM: dts: AM33xx: Add RNG node
  ARM: dts: AM33XX: Add hwspinlock node
  ARM: dts: OMAP5: Add hwspinlock node
  ARM: dts: OMAP4: Add hwspinlock node
  ARM: dts: use 'status' property for PCIe nodes
  ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
  ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
  ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
  ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
  ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  ...

1 files changed, 22 insertions, 24 deletions

diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index dfd83103657..fa532aaacc6 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -44,17 +44,6 @@
 		};
 	};
 
-	/* HS USB Port 2 RESET */
-	hsusb2_reset: hsusb2_reset_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "hsusb2_reset";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio5 19 0>;	/* gpio_147 */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-
 	/* HS USB Port 2 Power */
 	hsusb2_power: hsusb2_power_reg {
 		compatible = "regulator-fixed";
@@ -68,7 +57,7 @@
 	/* HS USB Host PHY on PORT 2 */
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
-		reset-supply = <&hsusb2_reset>;
+		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;	/* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
 	};
 
@@ -101,18 +90,18 @@
 
 	hsusbb2_pins: pinmux_hsusbb2_pins {
 		pinctrl-single,pins = <
-			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* usbb2_ulpitll_clk.usbb1_ulpiphy_clk */
-			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* usbb2_ulpitll_clk.usbb1_ulpiphy_stp */
-			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dir */
-			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_nxt */
-			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat0 */
-			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat1 */
-			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat2 */
-			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat3 */
-			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat4 */
-			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat5 */
-			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat6 */
-			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* usbb2_ulpitll_clk.usbb1_ulpiphy_dat7 */
+			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
 		>;
 	};
 
@@ -180,3 +169,12 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&gpio1_pins>;
 };
+
+&usb_otg_hs {
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
+};