Merge tag 'nomadik-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt

Merge "Nomadik updates for the v3.19 series" from Linus Walleij:

Nomadik changes for the v3.19 development series:
- Rearrange the DTS files to make a pure SoC-specific file and
  a pure board file for S8815.
- Add the device tree for the NDK15 board.
- Update the defconfig and configure in the STMPE expander by
  default on the Nomadik.

* tag 'nomadik-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: nomadik: configure in STMPE support
  ARM: update Nomadik config
  ARM: nomadik: device tree for NHK15 board
  ARM: nomadik: push ethernet down to board
  ARM: nomadik: set up MCDATDIR2
  ARM: nomadik: move GPIO I2C to S8815 board file
  ARM: nomadik: disable chrystals in top level board files
  ARM: nomadik: move MMC/SD card detect GPIO to board DTS

Signed-off-by: Olof Johansson <olof@lixom.net>

4 files changed, 204 insertions, 51 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cfe973fe424..dde363b64f2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -279,7 +279,8 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \
 	imx28-tx28.dtb
-dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb
+dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb \
+	ste-nomadik-nhk15.dtb
 dtb-$(CONFIG_ARCH_NSPIRE) += nspire-cx.dtb \
 	nspire-tp.dtb \
 	nspire-clp.dtb
diff --git a/arch/arm/boot/dts/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/ste-nomadik-nhk15.dts
new file mode 100644
index 00000000000..a8c00ee7522
--- /dev/null
+++ b/arch/arm/boot/dts/ste-nomadik-nhk15.dts
@@ -0,0 +1,151 @@
+/*
+ * Device Tree for the ST-Ericsson Nomadik S8815 board
+ * Produced by Calao Systems
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "ste-nomadik-stn8815.dtsi"
+
+/ {
+	model = "Nomadik STN8815NHK";
+	compatible = "st,nomadik-nhk-15";
+
+	chosen {
+		bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
+	};
+
+	aliases {
+		stmpe-i2c0 = &stmpe0;
+		stmpe-i2c1 = &stmpe1;
+	};
+
+	pinctrl {
+		stmpe2401_1 {
+			stmpe2401_1_nhk_mode: stmpe2401_1_nhk {
+				nhk_cfg1 {
+					ste,pins = "GPIO76_B20"; // IRQ line
+					ste,input = <0>;
+				};
+				nhk_cfg2 {
+					ste,pins = "GPIO77_B8"; // reset line
+					ste,output = <1>;
+				};
+			};
+		};
+		stmpe2401_2 {
+			stmpe2401_2_nhk_mode: stmpe2401_2_nhk {
+				nhk_cfg1 {
+					ste,pins = "GPIO78_A8"; // IRQ line
+					ste,input = <0>;
+				};
+				nhk_cfg2 {
+					ste,pins = "GPIO79_C9"; // reset line
+					ste,output = <1>;
+				};
+			};
+		};
+	};
+
+	src@101e0000 {
+		/* These chrystal outputs are not used on this board */
+		disable-sxtalo;
+		disable-mxtalo;
+	};
+
+	/* This is where the interrupt is routed on the NHK-15 debug board */
+	external-bus@34000000 {
+		compatible = "simple-bus";
+		reg = <0x34000000 0x1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x34000000 0x1000000>;
+		ethernet@300 {
+			compatible = "smsc,lan91c111";
+			reg = <0x300 0x0fd00>;
+			reg-io-width = <2>;
+			reset-gpios = <&stmpe_gpio44 10 GPIO_ACTIVE_HIGH>;
+			interrupt-parent = <&stmpe_gpio44>;
+			interrupts = <11 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	i2c0 {
+		stmpe0: stmpe2401@43 {
+			compatible = "st,stmpe2401";
+			reg = <0x43>;
+			reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; // GPIO77
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>; // GPIO76
+			interrupt-parent = <&gpio2>;
+			interrupt-controller;
+			wakeup-source;
+			pinctrl-names = "default";
+			pinctrl-0 = <&stmpe2401_1_nhk_mode>;
+			stmpe_gpio43: stmpe_gpio {
+				compatible = "st,stmpe-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				/* Some pins in alternate functions */
+				st,norequest-mask = <0xf0f002>;
+			};
+			stmpe_keypad {
+				compatible = "st,stmpe-keypad";
+				debounce-interval = <64>;
+				st,scan-count = <8>;
+				st,no-autorepeat;
+				keypad,num-rows = <8>;
+				keypad,num-columns = <8>;
+				linux,keymap = <0x00020072 // Vol down
+						0x00030073 // Vol up
+						0x0100009e // Back
+						0x010100e3 // TV out
+						0x01020098 // Lock
+						0x0103013b // Start
+						0x020000a3 // Next
+						0x020100a4 // Play
+						0x020200a5 // Prev
+						0x02030160 // OK
+						0x03000069 // Left
+						0x0301006a // Right
+						0x03020067 // Up
+						0x0303006c>; // Down
+			};
+		};
+		stmpe1: stmpe2401@44 {
+			compatible = "st,stmpe2401";
+			reg = <0x44>;
+			reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; // GPIO79
+			interrupts = <14 IRQ_TYPE_EDGE_FALLING>; // GPIO78
+			interrupt-parent = <&gpio2>;
+			interrupt-controller;
+			wakeup-source;
+			pinctrl-names = "default";
+			pinctrl-0 = <&stmpe2401_2_nhk_mode>;
+			stmpe_gpio44: stmpe_gpio {
+				compatible = "st,stmpe-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+		};
+	};
+
+	amba {
+		mmcsd: sdi@101f6000 {
+			cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>;
+			wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	/* Custom board node with GPIO pins to active etc */
+	usb-s8815 {
+		/* This will turn off SATA so that MMC/SD can thrive */
+		mmcsd-gpio {
+			gpios = <&stmpe_gpio44 2 0x1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-nomadik-s8815.dts b/arch/arm/boot/dts/ste-nomadik-s8815.dts
index 90d8b6c7a20..e411ff7769f 100644
--- a/arch/arm/boot/dts/ste-nomadik-s8815.dts
+++ b/arch/arm/boot/dts/ste-nomadik-s8815.dts
@@ -4,6 +4,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "ste-nomadik-stn8815.dtsi"
 
 / {
@@ -14,14 +15,6 @@
 		bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
 	};
 
-	/* This is where the interrupt is routed on the S8815 board */
-	external-bus@34000000 {
-		ethernet@300 {
-			interrupt-parent = <&gpio3>;
-			interrupts = <8 0x1>;
-		};
-	};
-
 	src@101e0000 {
 		/* These chrystal drivers are not used on this board */
 		disable-sxtalo;
@@ -47,6 +40,14 @@
 				};
 			};
 		};
+		gpioi2c {
+			gpioi2c_default_mode: gpioi2c_default {
+				gpioi2c_default_cfg {
+					ste,pins = "GPIO73_C21", "GPIO74_C20";
+					ste,input = <0>;
+				};
+			};
+		};
 		user-led {
 			user_led_default_mode: user_led_default {
 				user_led_default_cfg {
@@ -65,6 +66,45 @@
 		};
 	};
 
+	/* Ethernet */
+	external-bus@34000000 {
+		compatible = "simple-bus";
+		reg = <0x34000000 0x1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x34000000 0x1000000>;
+		ethernet@300 {
+			compatible = "smsc,lan91c111";
+			reg = <0x300 0x0fd00>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <8 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	/* GPIO I2C connected to the USB portions of the STw4811 only */
+	gpio-i2c {
+		compatible = "i2c-gpio";
+		gpios = <&gpio2 10 0>, /* sda */
+			<&gpio2 9 0>; /* scl */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpioi2c_default_mode>;
+
+		stw4811@2d {
+			   compatible = "st,stw4811-usb";
+			   reg = <0x2d>;
+		};
+	};
+
+
+	/* Configure card detect for the uSD slot */
+	amba {
+		mmcsd: sdi@101f6000 {
+			cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
 	/* Custom board node with GPIO pins to active etc */
 	usb-s8815 {
 		/* This will bias the MMC/SD card detect line */
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
index dbcf521b017..f435ff20aef 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
@@ -117,7 +117,7 @@
 			mmcsd_default_mux: mmcsd_mux {
 				mmcsd_default_mux {
 					ste,function = "mmcsd";
-					ste,pins = "mmcsd_a_1";
+					ste,pins = "mmcsd_a_1", "mmcsd_b_1";
 				};
 			};
 			mmcsd_default_mode: mmcsd_default {
@@ -127,9 +127,9 @@
 					ste,output = <0>;
 				};
 				mmcsd_default_cfg2 {
-					/* MCCMDDIR, MCDAT0DIR, MCDAT31DIR */
+					/* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */
 					ste,pins = "GPIO10_C11", "GPIO15_A12",
-					"GPIO16_C13";
+					"GPIO16_C13", "GPIO23_D15";
 					ste,output = <1>;
 				};
 				mmcsd_default_cfg3 {
@@ -169,21 +169,11 @@
 				};
 			};
 		};
-		i2c2 {
-			i2c2_default_mode: i2c2_default {
-				i2c2_default_cfg {
-					ste,pins = "GPIO73_C21", "GPIO74_C20";
-					ste,input = <0>;
-				};
-			};
-		};
 	};
 
 	src: src@101e0000 {
 		compatible = "stericsson,nomadik-src";
 		reg = <0x101e0000 0x1000>;
-		disable-sxtalo;
-		disable-mxtalo;
 
 		/*
 		 * MXTAL "Main Chrystal" is a chrystal oscillator @19.2 MHz
@@ -683,18 +673,6 @@
 		};
 	};
 
-	external-bus@34000000 {
-		compatible = "simple-bus";
-		reg = <0x34000000 0x1000000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0x34000000 0x1000000>;
-		ethernet@300 {
-			compatible = "smsc,lan91c111";
-			reg = <0x300 0x0fd00>;
-		};
-	};
-
 	/* I2C0 connected to the STw4811 power management chip */
 	i2c0 {
 		compatible = "st,nomadik-i2c", "arm,primecell";
@@ -749,22 +727,6 @@
 		};
 	};
 
-	/* I2C2 connected to the USB portions of the STw4811 only */
-	i2c2 {
-		compatible = "i2c-gpio";
-		gpios = <&gpio2 10 0>, /* sda */
-			<&gpio2 9 0>; /* scl */
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_default_mode>;
-
-		stw4811@2d {
-			   compatible = "st,stw4811-usb";
-			   reg = <0x2d>;
-		};
-	};
-
 	amba {
 		compatible = "arm,amba-bus";
 		#address-cells = <1>;
@@ -844,7 +806,6 @@
 			bus-width = <4>;
 			cap-mmc-highspeed;
 			cap-sd-highspeed;
-			cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
 			vmmc-supply = <&vmmc_regulator>;