Merge branch 'devicetree/for-x86' of git://git.secretlab.ca/git/linux-2.6 into x86/platform

Reason: x86 devicetree support for ce4100 depends on those device tree
	changes scheduled for .39.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

1 files changed, 10 insertions, 43 deletions

diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index 9d833bbc592..55dad3a4654 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -43,24 +43,21 @@
 #include "generic.h"
 
 
-/*
- * Serial port configuration.
- *    0 .. 3 = USART0 .. USART3
- *    4      = DBGU
- */
-static struct at91_uart_config __initdata picotux200_uart_config = {
-	.console_tty	= 0,				/* ttyS0 */
-	.nr_tty		= 2,
-	.tty_map	= { 4, 1, -1, -1, -1 }		/* ttyS0, ..., ttyS4 */
-};
-
 static void __init picotux200_map_io(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91rm9200_initialize(18432000, AT91RM9200_BGA);
 
-	/* Setup the serial ports and console */
-	at91_init_serial(&picotux200_uart_config);
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			  | ATMEL_UART_RI);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
 }
 
 static void __init picotux200_init_irq(void)
@@ -77,11 +74,6 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.ports		= 1,
 };
 
-// static struct at91_udc_data __initdata picotux200_udc_data = {
-// 	.vbus_pin	= AT91_PIN_PD4,
-// 	.pullup_pin	= AT91_PIN_PD5,
-// };
-
 static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.det_pin	= AT91_PIN_PB27,
 	.slot_b		= 0,
@@ -89,21 +81,6 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.wp_pin		= AT91_PIN_PA17,
 };
 
-// static struct spi_board_info picotux200_spi_devices[] = {
-// 	{	/* DataFlash chip */
-// 		.modalias	= "mtd_dataflash",
-// 		.chip_select	= 0,
-// 		.max_speed_hz	= 15 * 1000 * 1000,
-// 	},
-// #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-// 	{	/* DataFlash card */
-// 		.modalias	= "mtd_dataflash",
-// 		.chip_select	= 3,
-// 		.max_speed_hz	= 15 * 1000 * 1000,
-// 	},
-// #endif
-// };
-
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0
 #define PICOTUX200_FLASH_SIZE	SZ_4M
 
@@ -135,21 +112,11 @@ static void __init picotux200_board_init(void)
 	at91_add_device_eth(&picotux200_eth_data);
 	/* USB Host */
 	at91_add_device_usbh(&picotux200_usbh_data);
-	/* USB Device */
-	// at91_add_device_udc(&picotux200_udc_data);
-	// at91_set_multi_drive(picotux200_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	// at91_add_device_spi(picotux200_spi_devices, ARRAY_SIZE(picotux200_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-	/* DataFlash card */
-	at91_set_gpio_output(AT91_PIN_PB22, 0);
-#else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
 	at91_add_device_mmc(0, &picotux200_mmc_data);
-#endif
 	/* NOR Flash */
 	platform_device_register(&picotux200_flash);
 }