at91: rename rm9200ek and rm9200dk board file name

to be a few more concistant with the other boards

as ek is for evaluation kit and dk for development kit

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>

1 files changed, 201 insertions, 0 deletions

diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c
new file mode 100644
index 00000000000..9df1be8818c
--- /dev/null
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -0,0 +1,201 @@
+/*
+ * linux/arch/arm/mach-at91/board-rm9200ek.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *
+ *  Epson S1D framebuffer glue code is:
+ *     Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_BGA);
+
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
+
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata ek_eth_data = {
+	.phy_irq_pin	= AT91_PIN_PC4,
+	.is_rmii	= 1,
+};
+
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PD4,
+	.pullup_pin	= AT91_PIN_PD5,
+};
+
+#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
+static struct at91_mmc_data __initdata ek_mmc_data = {
+	.det_pin	= AT91_PIN_PB27,
+	.slot_b		= 0,
+	.wire4		= 1,
+	.wp_pin		= AT91_PIN_PA17,
+};
+#endif
+
+static struct spi_board_info ek_spi_devices[] = {
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+	},
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 3,
+		.max_speed_hz	= 15 * 1000 * 1000,
+	},
+#endif
+};
+
+static struct i2c_board_info __initdata ek_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("ics1523", 0x26),
+	},
+	{
+		I2C_BOARD_INFO("dac3550", 0x4d),
+	}
+};
+
+#define EK_FLASH_BASE	AT91_CHIPSELECT_0
+#define EK_FLASH_SIZE	SZ_2M
+
+static struct physmap_flash_data ek_flash_data = {
+	.width		= 2,
+};
+
+static struct resource ek_flash_resource = {
+	.start		= EK_FLASH_BASE,
+	.end		= EK_FLASH_BASE + EK_FLASH_SIZE - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device ek_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &ek_flash_data,
+			},
+	.resource	= &ek_flash_resource,
+	.num_resources	= 1,
+};
+
+static struct gpio_led ek_leds[] = {
+	{	/* "user led 1", DS2 */
+		.name			= "green",
+		.gpio			= AT91_PIN_PB0,
+		.active_low		= 1,
+		.default_trigger	= "mmc0",
+	},
+	{	/* "user led 2", DS4 */
+		.name			= "yellow",
+		.gpio			= AT91_PIN_PB1,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	},
+	{	/* "user led 3", DS6 */
+		.name			= "red",
+		.gpio			= AT91_PIN_PB2,
+		.active_low		= 1,
+	}
+};
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* Ethernet */
+	at91_add_device_eth(&ek_eth_data);
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&ek_udc_data);
+	at91_set_multi_drive(ek_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
+	/* I2C */
+	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+	/* DataFlash card */
+	at91_set_gpio_output(AT91_PIN_PB22, 0);
+#else
+	/* MMC */
+	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
+	at91_add_device_mmc(0, &ek_mmc_data);
+#endif
+	/* NOR Flash */
+	platform_device_register(&ek_flash);
+	/* LEDs */
+	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+	/* VGA */
+//	ek_add_device_video();
+}
+
+MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
+	/* Maintainer: SAN People/Atmel */
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91rm9200_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END