at91: merge board USB-A9260 and USB-A9263 together

Merge boards together as they are barely the same.

Signed-off-by: Nico Erfurth <ne@erfurth.eu>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: updated to new machine_desc structure]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>

1 files changed, 290 insertions, 0 deletions

diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c
new file mode 100644
index 00000000000..b9b9847fa55
--- /dev/null
+++ b/arch/arm/mach-at91/board-usb-a926x.c
@@ -0,0 +1,290 @@
+/*
+ * linux/arch/arm/mach-at91/board-usb-a926x.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2007 Atmel Corporation.
+ *  Copyright (C) 2007 Calao-systems
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init ek_init_early(void)
+{
+	/* Initialize processor: 12.00 MHz crystal */
+	at91_initialize(12000000);
+
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PB11,
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+void ek_add_device_udc(void)
+{
+	if (machine_is_usb_a9260())
+		ek_udc_data.vbus_pin = AT91_PIN_PC5;
+
+	at91_add_device_udc(&ek_udc_data);
+}
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	}
+#endif
+};
+
+void ek_add_device_spi(void)
+{
+	if (machine_is_usb_a9263())
+		at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+}
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+	.phy_irq_pin	= AT91_PIN_PE31,
+	.is_rmii	= 1,
+};
+
+void ek_add_device_eth(void)
+{
+	if (machine_is_usb_a9260())
+		ek_macb_data.phy_irq_pin = AT91_PIN_PA31;
+
+	at91_add_device_eth(&ek_macb_data);
+}
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+	{
+		.name	= "Uboot & Kernel",
+		.offset	= 0,
+		.size	= SZ_16M,
+	},
+	{
+		.name	= "Root FS",
+		.offset	= MTDPART_OFS_NXTBLK,
+		.size	= 120 * SZ_1M,
+	},
+	{
+		.name	= "FS",
+		.offset	= MTDPART_OFS_NXTBLK,
+		.size	= 120 * SZ_1M,
+	}
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(ek_nand_partition);
+	return ek_nand_partition;
+}
+
+static struct atmel_nand_data __initdata ek_nand_data = {
+	.ale		= 21,
+	.cle		= 22,
+//	.det_pin	= ... not connected
+	.rdy_pin	= AT91_PIN_PA22,
+	.enable_pin	= AT91_PIN_PD15,
+	.partition_info	= nand_partitions,
+};
+
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 1,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 1,
+
+	.ncs_read_pulse		= 3,
+	.nrd_pulse		= 3,
+	.ncs_write_pulse	= 3,
+	.nwe_pulse		= 3,
+
+	.read_cycle		= 5,
+	.write_cycle		= 5,
+
+	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
+	.tdf_cycles		= 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+	if (machine_is_usb_a9260()) {
+		ek_nand_data.rdy_pin	= AT91_PIN_PC13;
+		ek_nand_data.enable_pin	= AT91_PIN_PC14;
+	}
+
+	/* configure chip-select 3 (NAND) */
+	sam9_smc_configure(3, &ek_nand_smc_config);
+
+	at91_add_device_nand(&ek_nand_data);
+}
+
+
+/*
+ * GPIO Buttons
+ */
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button ek_buttons[] = {
+	{	/* USER PUSH BUTTON */
+		.code		= KEY_ENTER,
+		.gpio		= AT91_PIN_PB10,
+		.active_low	= 1,
+		.desc		= "user_pb",
+		.wakeup		= 1,
+	}
+};
+
+static struct gpio_keys_platform_data ek_button_data = {
+	.buttons	= ek_buttons,
+	.nbuttons	= ARRAY_SIZE(ek_buttons),
+};
+
+static struct platform_device ek_button_device = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev		= {
+		.platform_data	= &ek_button_data,
+	}
+};
+
+static void __init ek_add_device_buttons(void)
+{
+	at91_set_GPIO_periph(AT91_PIN_PB10, 1);	/* user push button, pull up enabled */
+	at91_set_deglitch(AT91_PIN_PB10, 1);
+
+	platform_device_register(&ek_button_device);
+}
+#else
+static void __init ek_add_device_buttons(void) {}
+#endif
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+	{	/* user_led (green) */
+		.name			= "user_led",
+		.gpio			= AT91_PIN_PB21,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	}
+};
+
+void ek_add_device_leds(void)
+{
+	if (machine_is_usb_a9260())
+		ek_leds[0].active_low = 0;
+
+	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
+
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	ek_add_device_udc();
+	/* SPI */
+	ek_add_device_spi();
+	/* Ethernet */
+	ek_add_device_eth();
+	/* NAND */
+	ek_add_device_nand();
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
+	/* Push Buttons */
+	ek_add_device_buttons();
+	/* LEDs */
+	ek_add_device_leds();
+	/* shutdown controller, wakeup button (5 msec low) */
+	at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
+				| AT91_SHDW_RTTWKEN);
+}
+
+MACHINE_START(USB_A9263, "CALAO USB_A9263")
+	/* Maintainer: calao-systems */
+	.timer		= &at91sam926x_timer,
+	.map_io		= at91_map_io,
+	.init_early	= ek_init_early,
+	.init_irq	= at91_init_irq_default,
+	.init_machine	= ek_board_init,
+MACHINE_END
+
+MACHINE_START(USB_A9260, "CALAO USB_A9260")
+	/* Maintainer: calao-systems */
+	.timer		= &at91sam926x_timer,
+	.map_io		= at91_map_io,
+	.init_early	= ek_init_early,
+	.init_irq	= at91_init_irq_default,
+	.init_machine	= ek_board_init,
+MACHINE_END